Results for “parameter compression” — Page 46

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration using Transport Equation Models and Linear Stability Correlations

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework rely upon transition correlations that were derived from a limited number of low-speed experiments. Furthermore, these models often account for only a subset of the relevant transition mechanisms and/or cannot accurately predict the sensitivity of those mechanisms to the changes in significant flow parameters. A preceding investigation had targeted the assessment of the transport-equation-based transition models in NASA's OVERFLOW 2.3b solver, namely, the amplification factor transport (AFT-2017b) equation model coupled with the Spalart-Allmaras RANS model and the Langtry-Menter transition models (LM2009 without crossflow effects and LM2015 including the modeling of crossflow transition) implemented with Menter’s shear-stress transport equation (SST2003) RANS model. Comparisons with recent measurements at transonic freestream conditions on the Common Research Model with Natural Laminar Flow (CRM-NLF) reinforced our earlier finding that all three of the above models significantly underpredict the reported extent of the laminar flow region over the entire span of the wing, regardless of the dominant instability mechanism(s) underlying the onset of the transition process. The underprediction of the laminar flow extent was attributed to the failure of the above models in accounting for the stabilizing effect of compressibility on the amplification of Tollmien-Schlichting instabilities. Based on previous linear stability studies related to compressibility effects, the present work proposes modifications to the two classes of transition models that reduce to the original form of each model at low subsonic speeds and do not require any nonlocal flow information or additional transport equation(s). The modifications are shown to significantly improve the predicted laminar extent of the flow and compare well against the data from the CRM-NLF experiment. Additionally, a previous assessment of transition prediction based on the dual, nonparallel N -factor method in conjunction with linear parabolized stability equations (PSE) is extended to additional angles of attack to provide the first comprehensive assessment of transition models based on nonparallel disturbance amplification over the CRM-NLF. In general, the transition criterion based on the dual, nonparallel N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at R eMAC = 15 million for all angles of attack investigated herein and provides additional validation of the improved predictions from the compressibility-corrected transition models.

CFD modeling↗

NASA NTRS2022

Transition Analysis for the CRM-NLF Wind Tunnel Configuration using Transport Equation Models and Linear Stability Correlations

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework rely upon transition correlations that were derived from a limited number of low-speed experiments. Furthermore, these models often account for only a subset of the relevant transition mechanisms and/or cannot accurately predict the sensitivity of those mechanisms to the changes in significant flow parameters. A preceding investigation had targeted the assessment of the transport-equation-based transition models in NASA's OVERFLOW 2.3b solver, namely, the amplification factor transport (AFT-2017b) equation model coupled with the Spalart-Allmaras RANS model and the Langtry-Menter transition models (LM2009 without crossflow effects and LM2015 including the modeling of crossflow transition) implemented with Menter’s shear-stress transport equation (SST2003) RANS model. Comparisons with recent measurements at transonic freestream conditions on the Common Research Model with Natural Laminar Flow (CRM-NLF) reinforced our earlier finding that all three of the above models significantly underpredict the reported extent of the laminar flow region over the entire span of the wing, regardless of the dominant instability mechanism(s) underlying the onset of the transition process. The underprediction of the laminar flow extent was attributed to the failure of the above models in accounting for the stabilizing effect of compressibility on the amplification of Tollmien-Schlichting instabilities. Based on previous linear stability studies related to compressibility effects, the present work proposes modifications to the two classes of transition models that reduce to the original form of each model at low subsonic speeds and do not require any nonlocal flow information or additional transport equation(s). The modifications are shown to significantly improve the predicted laminar extent of the flow and compare well against the data from the CRM-NLF experiment. Additionally, a previous assessment of transition prediction based on the dual, nonparallel N -factor method in conjunction with linear parabolized stability equations (PSE) is extended to additional angles of attack to provide the first comprehensive assessment of transition models based on nonparallel disturbance amplification over the CRM-NLF. In general, the transition criterion based on the dual, nonparallel N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at R eMAC = 15 million for all angles of attack investigated herein and provides additional validation of the improved predictions from the compressibility-corrected transition models.

CFD modeling↗

NASA NTRS1991

Compressible flows with periodic vortical disturbances around lifting airfoils

A numerical method is developed for solving periodic, three-dimensional, vortical flows around lifting airfoils in subsonic flow. The first-order method that is presented fully accounts for the distortion effects of the nonuniform mean flow on the convected upstream vortical disturbances. The unsteady velocity is split into a vortical component which is a known function of the upstream flow conditions and the Lagrangian coordinates of the mean flow, and an irrotational field whose potential satisfies a nonconstant-coefficient, inhomogeneous, convective wave equation. Using an elliptic coordinate transformation, the unsteady boundary value problem is solved in the frequency domain on grids which are determined as a function of the Mach number and reduced frequency. The numerical scheme is validated through extensive comparisons with known solutions to unsteady vortical flow problems. In general, it is seen that the agreement between the numerical and analytical results is very good for reduced frequencies ranging from 0 to 4, and for Mach numbers ranging from .1 to .8. Numerical results are also presented for a wide variety of flow configurations for the purpose of determining the effects of airfoil thickness, angle of attack, camber, and Mach number on the unsteady lift and moment of airfoils subjected to periodic vortical gusts. It is seen that each of these parameters can have a significant effect on the unsteady airfoil response to the incident disturbances, and that the effect depends strongly upon the reduced frequency and the dimensionality of the gust. For a one-dimensional (transverse) or two-dimensional (transverse and longitudinal) gust, the results indicate that airfoil thickness increases the unsteady lift and moment at the low reduced frequencies but decreases it at the high reduced frequencies. The results show that an increase in airfoil Mach number leads to a significant increase in the unsteady lift and moment for the low reduced frequencies, but a significant decrease for the high reduced frequencies.

Scott, James R.↗

NASA NTRS2024

Scalability in SLA lattice through lattice orientation and hybrid frame and plate architectures

Lightweighting has been a key goal for engineers and designers, with lattice structures widely explored as the building blocks for structural components. Cellular structure-inspired lattice truss frame designs made of struts, have been extensively studied. All plate-based lattice designs have superior mechanical performance. Limits in scalability occur from formation of closed pockets limiting uv curing in processes like stereolithography (SLA). We examine hybrid frame and plate body-centered cubic-simply cubic (BCC-SC) lattices under compression. Unit cells and scaled up lattice exhibit an increase in yield stress and modulus with the addition of plates. The loading direction on the hybrid frame and plate unit cells affected the magnitude of improvement. Simulations and measurements indicated that the optimal lightweight lattice was determined to be when two plates were placed opposite each other with plates buttressing the struts, inhibiting buckling of the struts aligned with the loading direction. This lattice resulted in 63% improvement in specific modulus, a 137% improvement in specific yield point, and a 360% improvement in specific energy absorption (SEA) and the scaled up 4 × 4 × 4 scaled-up structures, showed a 107%, 148%, and 297% in specific modulus, specific yield point, and SEA, respectively A combined stretching-bending behavior was identified in optimal orientations reflecting the delayed buckling mechanism paired to a rising stress-strain curve past the elastic yield indicating bending resistance. The mass moment of inertia was found to be a key parameter correlating optimum orientation for the same number of plates added to the BCC-SC frame.

Mahan Ghosh↗

NASA NTRS1990

Investigation of advanced counterrotation blade configuration concepts for high speed turboprop systems, task 1: Ducted propfan analysis

The time-dependent three-dimensional Euler equations of gas dynamics were solved numerically to study the steady compressible transonic flow about ducted propfan propulsion systems. Aerodynamic calculations were based on a four-stage Runge-Kutta time-marching finite volume solution technique with added numerical dissipation. An implicit residual smoothing operator was used to aid convergence. Two calculation grids were employed in this study. The first grid utilized an H-type mesh network with a branch cut opening to represent the axisymmetric cowl. The second grid utilized a multiple-block mesh system with a C-type grid about the cowl. The individual blocks were numerically coupled in the Euler solver. Grid systems were generated by a combined algebraic/elliptic algortihm developed specifically for ducted propfans. Numerical calculations were initially performed for unducted propfans to verify the accuracy of the three-dimensional Euler formulation. The Euler analyses were then applied for the calculation of ducted propfan flows, and predicted results were compared with experimental data for two cases. The three-dimensional Euler analyses displayed exceptional accuracy, although certain parameters were observed to be very sensitive to geometric deflections. Both solution schemes were found to be very robust and demonstrated nearly equal efficiency and accuracy, although it was observed that the multi-block C-grid formulation provided somewhat better resolution of the cowl leading edge region.

Hall, Edward J.↗

NASA NTRS1995

Out-of-plane properties

This paper summarizes three areas of research which were performed to characterize out-of-plane properties of composite materials. In the first investigation, a series of tests was run to characterize the through-the-thickness tensile strength for a variety of composites that included 2D braids, 2D and 3D weaves, and prepreg tapes. A new test method based on a curved beam was evaluated. Failures were significantly different between the 2D materials and the 3D weaves. The 2D materials delaminated between layers due to out-of-plane tensile stresses while the 3D weaves failed due to the formation of radial cracks between the surface plies caused by high circumferential stresses along the inner radius. The strength of the 2D textile composites did not increase relative to the tapes. Final failure in the 3D weaves was caused by a circumferential crack similar to the 2D materials and occurred at a lower bending moment than in other materials. The early failures in the 3D weaves were caused by radial crack formation rather than a low through-the-thickness strength. The second investigation focused on the development of a standard impact test method to measure impact damage resistance. The only impact tests that currently exist are compression after impact (CAI) tests which incorporate elements of both damage resistance and damage tolerance. A new impact test method is under development which uses a quasi-static indentation (QSI) test to directly measure damage resistance. Damage resistance is quantified in terms of the contact force to produce a unit of damage where a metric for damage may be area in C-scan, depth of residual dent , penetration, damage growth, etc. A final draft of an impact standard that uses a QSI test method will be presented to the ASTM Impact Task Group on impact. In the third investigation, the impact damage resistance behavior of a variety of textile materials was studied using the QSI test method. In this study, the force where large damage initiates was measured and the delamination size as a function of force was determined. The force to initiate large damage was significantly lower in braids and weaves. The delamination diameter - impact forace relationship was quanitfied using a damage resistance parameter, Q(*), which related delamination diameter to imapct force over a range of delamination sizes. Using this Q(*) parameter to rate the materials, the stitched uniweaves, toughened epoxy tapes, and through-the-thickness orthogonal interlock weave were the most damage resistant.

Jackson, Wade C.↗

NASA NTRS2005

A Feasibility Study for Simultaneous Measurements of Water Vapor and Precipitation Parameters using a Three-frequency Radar

The radar return powers from a three-frequency radar, with center frequency at 22.235 GHz and upper and lower frequencies chosen with equal water vapor absorption coefficients, can be used to estimate water vapor density and parameters of the precipitation. A linear combination of differential measurements between the center and lower frequencies on one hand and the upper and lower frequencies on the other provide an estimate of differential water vapor absorption. The coupling between the precipitation and water vapor estimates is generally weak but increases with bandwidth and the amount of non-Rayleigh scattering of the hydrometeors. The coupling leads to biases in the estimates of water vapor absorption that are related primarily to the phase state and the median mass diameter of the hydrometeors. For a down-looking radar, path-averaged estimates of water vapor absorption are possible under rain-free as well as raining conditions by using the surface returns at the three frequencies. Simulations of the water vapor attenuation retrieval show that the largest source of error typically arises from the variance in the measured radar return powers. Although the error can be mitigated by a combination of a high pulse repetition frequency, pulse compression, and averaging in range and time, the radar receiver must be stable over the averaging period. For fractional bandwidths of 20% or less, the potential exists for simultaneous measurements at the three frequencies with a single antenna and transceiver, thereby significantly reducing the cost and mass of the system.

Meneghini, R.↗

NASA NTRS2021

Assessment of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon transition correlations that were derived from a limited number of low-speed experiments and these models often fail to account for all of the relevant transition mechanisms and/or the variation in those mechanisms with respect to changes in the significant flow parameters. Available data from a recent experiment on the Common Research Model with Natural Laminar Flow (CRM-NLF) in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.3b solver for a swept wing configuration with nonzero taper and transonic cruise conditions. Specifically, the OVERFLOW solutions are used to evaluate the accuracy and robustness of the transport-equation-based transition models. Results highlight that the Spalart-Allmaras-based amplification factor transport (AFT-2017b) equation model and Menter’s shear-stress transport equation (SST2003)-based Langtry-Menter transition models (either with or without the modeling of crossflow transition) significantly underpredict the reported extent of laminar flow region over the entire span of the wing, irrespective of which instability mechanism(s) is expected to dominate the onset of the transition process. We show that the transition correlations underlying these models fail to account for the stabilizing effect of compressibility on the Tollmien-Schlichting transition, which is likely to be a major contributor to the underprediction of the laminar flow region on the CRM-NLF. The SST-2003-based Langtry-Menter model also appears to inaccurately predict the chordwise pressure variation along the majority of the wing span at all the flow conditions studied herein, due to how the turbulence intensity levels were enforced in the computations and how that was interfering with the functioning of the underlying turbulence model within the boundary layer. The AFT and Langtry-Menter models appear to be sensitive to the level of the freestream turbulence intensity, but the degree of sensitivity varies across the models.

CFD modeling↗

NASA NTRS2015

Evaluation of Industry Standard Turbulence Models on an Axisymmetric Supersonic Compression Corner

Reynolds-averaged Navier-Stokes computations of a shock-wave/boundary-layer interaction (SWBLI) created by a Mach 2.85 flow over an axisymmetric 30-degree compression corner were carried out. The objectives were to evaluate four turbulence models commonly used in industry, for SWBLIs, and to evaluate the suitability of this test case for use in further turbulence model benchmarking. The Spalart-Allmaras model, Menter's Baseline and Shear Stress Transport models, and a low-Reynolds number k- model were evaluated. Results indicate that the models do not accurately predict the separation location; with the SST model predicting the separation onset too early and the other models predicting the onset too late. Overall the Spalart-Allmaras model did the best job in matching the experimental data. However there is significant room for improvement, most notably in the prediction of the turbulent shear stress. Density data showed that the simulations did not accurately predict the thermal boundary layer upstream of the SWBLI. The effect of turbulent Prandtl number and wall temperature were studied in an attempt to improve this prediction and understand their effects on the interaction. The data showed that both parameters can significantly affect the separation size and location, but did not improve the agreement with the experiment. This case proved challenging to compute and should provide a good test for future turbulence modeling work.

Turbulent Boundary Layer↗

NASA NTRS2006

Comanche Helmet-Mounted Display Symbology Simulation

The Aeroflightdynamics Directorate (AMRDEC) conducted a simulation to examine the performance of the Comanche Contact Analog world-referenced symbology displayed on the Comanche HIDSS when compared with a compressed symbology design similar to that specified by the former MIL-STD 1295. Six experimental test pilots flew one modified ADS-33 maneuver (hover turn, bob-up), an unusual attitude recovery, and two terrain flight tactical tasks in the NASA Vertical Motion Simulator (VMS). Analysis of the pilot objective performance data and subjective data showed the following results. Objective test results showed that 1295 symbology yielded more rapid maneuvering in the hover turn bob-up than Contact Analog symbology. The average margin of difference in the time to complete the maneuver was approximately two seconds, which was statistically significant. There were no significant differences measured between symbology sets with respect to altitude or position performance measures for all other maneuvers. The NOE target ID task data showed improved accuracy in determining heading to target when using Contact Analog over MIL-STD-1295. Subjective test results, including handling qualities ratings (HQRs) and NASA-TLX workload ratings, showed small but consistent advantages of 1295 symbology over Contact Analog for most parameters. For the bob-up maneuver, 1295 symbology handling qualities were rated Desired for lateral position error and time to complete whereas Contact Analog was rated adequate. The average HQRs for all other maneuvers were rated the same for both symbology sets. Pilot comments and the results of an online questionnaire more strongly favored 1295 over Contact Analog. Repeated comments from all six pilots led to a focus on design issues with six Contact Analog symbols. Those symbols were the heading tape, horizon line, radar altitude six-second predictor, the position of the torque symbol, the absence of a hover position cue, and the widespread positioning of the symbology to the outer edges of the display field-of-view. Pilots rated the present design of three of the six symbols as having safety-of-flight implications. Those symbols were the heading tape, horizon line, and six-second predictor. To summarize, test results showed no objective data that would warrant restricting experimental test pilots from flying constrained tasks. Small but consistent advantages were recorded for the MILSTD-1295 symbology design when executing ADS-33 constrained tasks. No general performance differences were recorded for the operational maneuvers (NOE, contour flight modes) except for the azimuth-to-target task, which favored the Contact Analog heading tape design. There were consistent and strong pilot comments supporting the MIL-STD-1295 design over Contact Analog in both this current simulation and in Comanche Sim I. Three Contact Analog symbols warrant modification and further evaluation to mitigate safety-of-flight implications noted by participating test pilots. A plan for symbology redesign and testing was developed. However, the Comanche program was cancelled by Department of Army in February 2004.

Turpin, Terry S.↗

NASA NTRS1993

Ulysses plasma observations in the Jovian magnetosheath

The solar wind plasma experiment aboard the Ulysses spacecraft, including separate ion and electron instruments, measured the plasma properties of the Jovian magnetosheath during the February 1992 encounter with Jupiter. Seven separate magnetosheath intervals were observed, as well as four bow shock crossings and numerous encounters with the magnetopause and its boundary layer. We present an overview of ion and electron bulk parameters and a sampling of distribution shapes for the magnetosheath and adjacent plasma regions. Plasma flows are generally appropriate for slowing and deflection of the solar wind flow about a relatively stationary obstacle, with the notable exception of the first inbound sheath transit, when an expanding magnetosphere resulted in sunward flow just above the magnetopause. The existence of a planetary depletion layer is suggested by trends in plasma density for some magnetopause encounters. The magnetopause boundary layer is characterized by a combination of sheathlike and magnetospheric distributions of both ions and electrons. The ion population in the sheath is observed to include a significant population of suprathermal protons. Electron distributions have a distinctive shape previously observed in the terrestrial magnetosheath, with fluxes parallel to the magnetic field dominating at thermal energies and perpendicular fluxes dominating at higher energies. Trends in electron temperature near the bow shock indicate that shock motion plays an important role in heating the electrons. In general, the plasma characteristics of the Jovian magnetosheath are quite similar to those in its terrestrial counterpart, but the compressible nature of the Jovian magnetosphere accentuates the importance of boundary motions.

Phillips, J. L.↗

NASA NTRS2010

Z-Pinch Pulsed Plasma Propulsion Technology Development

Fusion-based propulsion can enable fast interplanetary transportation. Magneto-inertial fusion (MIF) is an approach which has been shown to potentially lead to a low cost, small reactor for fusion break even. The Z-Pinch/dense plasma focus method is an MIF concept in which a column of gas is compressed to thermonuclear conditions by an axial current (I approximates 100 MA). Recent advancements in experiments and the theoretical understanding of this concept suggest favorable scaling of fusion power output yield as I(sup 4). This document presents a conceptual design of a Z-Pinch fusion propulsion system and a vehicle for human exploration. The purpose of this study is to apply Z-Pinch fusion principles to the design of a propulsion system for an interplanetary spacecraft. This study took four steps in service of that objective; these steps are identified below. 1. Z-Pinch Modeling and Analysis: There is a wealth of literature characterizing Z-Pinch physics and existing Z-Pinch physics models. In order to be useful in engineering analysis, simplified Z-Pinch fusion thermodynamic models are required to give propulsion engineers the quantity of plasma, plasma temperature, rate of expansion, etc. The study team developed these models in this study. 2. Propulsion Modeling and Analysis: While the Z-Pinch models characterize the fusion process itself, propulsion models calculate the parameters that characterize the propulsion system (thrust, specific impulse, etc.) The study team developed a Z-Pinch propulsion model and used it to determine the best values for pulse rate, amount of propellant per pulse, and mixture ratio of the D-T and liner materials as well as the resulting thrust and specific impulse of the system. 3. Mission Analysis: Several potential missions were studied. Trajectory analysis using data from the propulsion model was used to determine the duration of the propulsion burns, the amount of propellant expended to complete each mission considered. 4. Vehicle Design: To understand the applicability of Z-Pinch propulsion to interplanetary travel, it is necessary to design a concept vehicle that uses it -- the propulsion system significantly impacts the design of the electrical, thermal control, avionics and structural subsystems of a vehicle. The study team developed a conceptual design of an interplanetary vehicle that transports crew and cargo to Mars and back and can be reused for other missions. Several aspects of this vehicle are based on a previous crewed fusion vehicle study -- the Human Outer Planet Exploration (HOPE) Magnetized Target Fusion (MTF) vehicle. Portions of the vehicle design were used outright and others were modified from the MTF design in order to maintain comparability.

Polsgrove, Tara↗

NASA NTRS1994

The proton cyclotron instability and the anisotropy/B inverse correlation

Spacecraft observations in the strongly compressed subsolar magnetosheath show an inverse correlation between the proton temperature anistrophy (T(sub perpendicular to p)/T(sub parallel to p) greater than 1 where perpendicular to and parallel to denote directions perpendicular and parallel to the background magnetic field) and the parallel proton beta (beta(sub parallel to p). This manuscript uses one-dimensional hybrid simulations of the proton cyclotron anisotropy instability in homogeneous electron-proton plasmas to study this correlation which may represent a limited closure relation for fluid theories of anisotropic space plasmas. The emphasis is on driven simulation which increase the temperature anisotropy by periodically reducing the magnetic-field-aligned velocities of the protons. The late-time states from ensembles of both initial value and driven simulations yield very similar expressions for the proton anisotropy/beta(sub parallel to P) inverse correlation, and provide a basis for explaining differences between sheath observations from different spacecraft. The driven simulations also yield expressions for the maximum instability growth rate and the fluctuating field energy as functions of beta (sub parallel to p) and a parameter characterizing the anisotropy driver.

Gary, S. Peter↗

NASA NTRS1992

Model based estimation of image depth and displacement

Passive depth and displacement map determinations have become an important part of computer vision processing. Applications that make use of this type of information include autonomous navigation, robotic assembly, image sequence compression, structure identification, and 3-D motion estimation. With the reliance of such systems on visual image characteristics, a need to overcome image degradations, such as random image-capture noise, motion, and quantization effects, is clearly necessary. Many depth and displacement estimation algorithms also introduce additional distortions due to the gradient operations performed on the noisy intensity images. These degradations can limit the accuracy and reliability of the displacement or depth information extracted from such sequences. Recognizing the previously stated conditions, a new method to model and estimate a restored depth or displacement field is presented. Once a model has been established, the field can be filtered using currently established multidimensional algorithms. In particular, the reduced order model Kalman filter (ROMKF), which has been shown to be an effective tool in the reduction of image intensity distortions, was applied to the computed displacement fields. Results of the application of this model show significant improvements on the restored field. Previous attempts at restoring the depth or displacement fields assumed homogeneous characteristics which resulted in the smoothing of discontinuities. In these situations, edges were lost. An adaptive model parameter selection method is provided that maintains sharp edge boundaries in the restored field. This has been successfully applied to images representative of robotic scenarios. In order to accommodate image sequences, the standard 2-D ROMKF model is extended into 3-D by the incorporation of a deterministic component based on previously restored fields. The inclusion of past depth and displacement fields allows a means of incorporating the temporal information into the restoration process. A summary on the conditions that indicate which type of filtering should be applied to a field is provided.

Damour, Kevin T.↗

NASA NTRS1994

Analysis of Airborne Radar Altimetry Measurements of the Greenland Ice Sheet

This dissertation presents an analysis of airborne altimetry measurements taken over the Greenland ice sheet with the 13.9 GHz Advanced Application Flight Experiment (AAFE) pulse compression radar altimeter. This Ku-band instrument was refurbished in 1990 by the Microwave Remote Sensing Laboratory at the University of Massachusetts to obtain high-resolution altitude measurements and to improve the tracking, speed, storage and display capabilities of the radar. In 1991 and 1993, the AAFE altimeter took part in the NASA Multisensor Airborne Altimetry Experiments over Greenland, along with two NASA laser altimeters. Altitude results from both experiments are presented along with comparisons to the laser altimeter and calibration passes over the Sondrestroem runway in Greenland. Although it is too early to make a conclusion about the growth or decay of the ice sheet, these results show that the instrument is capable of measuring small-scale surface changes to within 14 centimeters. In addition, results from these experiments reveal that the radar is sensitive to the different diagenetic regions of the ice sheet. Return waveforms from the wet- snow, percolation and dry-snow zones show varying effects of both surface scattering and sub-surface or volume scattering. Models of each of the diagenetic regions of Greenland are presented along with parameters such as rms surface roughness, rms surface slope and attenuation coefficient of the snow pack obtained by fitting the models to actual return waveforms.

Ferraro, Ellen J.↗

NASA NTRS1996

A Geophysical Flow Experiment in a Compressible Critical Fluid

The first objective of this experiment is to build an experimental system in which, in analogy to a geophysical system, a compressible fluid in a spherical annulus becomes radially stratified in density through an A.C. electric field. When this density gradient is demonstrated, the system will be augmented so that the fluid can be driven by heating and rotation and tested in preparation for a microgravity experiment. This apparatus consists of a spherical capacitor filled with critical fluid in a temperature controlled environment. To make the fluid critical, the apparatus will be operated near the critical pressure, critical density, and critical temperature of the fluid. This will result in a highly compressible fluid because of the properties of the fluid near its critical point. A high voltage A.C. source applied across the capacitor will create a spherically symmetric central force because of the dielectric properties of the fluid in an electric field gradient. This central force will induce a spherically symmetric density gradient that is analogous to a geophysical fluid system. To generate such a density gradient the system must be small (approx. 1 inch diameter). This small cell will also be capable of driving the critical fluid by heating and rotation. Since a spherically symmetric density gradient can only be made in microgravity, another small cell, of the same geometry, will be built that uses incompressible fluid. The driving of the fluid by rotation and heating in these small cells will be developed. The resulting instabilities from the driving in these two systems will then be studied. The second objective is to study the pattern forming instabilities (bifurcations) resulting from the well controlled experimental conditions in the critical fluid cell. This experiment will come close to producing conditions that are geophysically similar and will be studied as the driving parameters are changed.

Hegseth, John↗

NASA NTRS2000

THRSTER: A Three-Stream Ejector Ramjet Analysis and Design Tool

An engineering tool for analyzing ejectors in rocket based combined cycle (RBCC) engines has been developed. A key technology for multi-cycle RBCC propulsion systems is the ejector which functions as the compression stage of the ejector ramjet cycle. The THRee STream Ejector Ramjet analysis tool was developed to analyze the complex aerothermodynamic and combustion processes that occur in this device. The formulated model consists of three quasi-one-dimensional streams, one each for the ejector primary flow, the secondary flow, and the mixed region. The model space marches through the mixer, combustor, and nozzle to evaluate the solution along the engine. In its present form, the model is intended for an analysis mode in which the diffusion rates of the primary and secondary into the mixed stream are stipulated. The model offers the ability to analyze the highly two-dimensional ejector flowfield while still benefits from the simplicity and speed of an engineering tool. To validate the developed code, wall static pressure measurements from the Penn-State and NASA-ART RBCC experiments were used to compare with the results generated by the code. The calculated solutions were generally found to have satisfactory agreement with the pressure measurements along the engines, although further modeling effort may be required when a strong shock train is formed at the rocket exhaust. The range of parameters in which the code would generate valid results are presented and discussed.

Chue, R. S.↗

NASA NTRS2000

THRSTER: A THRee-STream Ejector Ramjet Analysis and Design Tool

An engineering tool for analyzing ejectors in rocket based combined cycle (RBCC) engines has been developed. A key technology for multi-cycle RBCC propulsion systems is the ejector which functions as the compression stage of the ejector ramjet cycle. The THRee STream Ejector Ramjet analysis tool was developed to analyze the complex aerothermodynamic and combustion processes that occur in this device. The formulated model consists of three quasi-one-dimensional streams, one each for the ejector primary flow, the secondary flow, and the mixed region. The model space marches through the mixer, combustor, and nozzle to evaluate the solution along the engine. In its present form, the model is intended for an analysis mode in which the diffusion rates of the primary and secondary into the mixed stream are stipulated. The model offers the ability to analyze the highly two-dimensional ejector flowfield while still benefits from the simplicity and speed of an engineering tool. To validate the developed code, wall static pressure measurements from the Penn-State and NASA-ART RBCC experiments were used to compare with the results generated by the code. The calculated solutions were generally found to have satisfactory agreement with the pressure measurements along the engines, although further modeling effort may be required when a strong shock train is formed at the rocket exhaust. The range of parameters in which the code would generate valid results are presented and discussed.

Chue, R. S.↗