Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “niobium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Microstructural Changes to Thermally Sprayed Materials Subjected to Dynamic Compression

Dynamic compression of materials can induce a variety of microstructural changes. As thermally-sprayed materials have highly complex microstructures, the expected pressure at which changes occur cannot be predicted a priori. In addition, typical in-situ measurements such as velocimetry are unable to adequately diagnose microstructural changes such as failure or pore collapse. Quasi-isentropic compression experiments with sample recovery were conducted to examine microstructural changes in thermally sprayed tantalum and tantalum-niobium blends up to 8 GPa pressure. Spall fracture was observed in all tests, and post-shot pore volume decreased relative to the initial state. The blended material exhibited larger spall planes with fracture occurring at interphase boundaries. An estimate of the pressure at which pore collapse is complete was determined to be ~26 GPa for pure tantalum and ~19 GPa for the tantalumniobium blend under these loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal / structural analysis of the HB 650 thermal shield

Fermilab’s PIP-II project’s superconducting linear accelerator will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield is the focus of this investigation. In preparation for operation, the thermal shield is cooled from 300K to 40K in a slow process over 2-1/2 days. The factors limiting the cooling rate are a high thermal gradient which produces thermal strain and high mechanical stress. D ecreasing the time required to reach operational temperatures is the desired research goal. Physical testing data and finite element method (FEM) computer models from the Single Spoke Resonator – 1 (SSR1) and Linac Coherent Light Source (LCLS-II) cryomodules will be evaluated to determine needed design changes. The thermal shield design for the High Beta 650 MHz (HB650) will be modified and analyzed using FEM computer models to determine maximum cooling rate with a target of 50 thermal cycles of life. Maximum allowable stress will be determined through low cycle fatigue calculations.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Transmitted wave measurements in cold sprayed materials under dynamic compression

Spray-formed materials have complex microstructures which pose challenges for microscale and mesoscale modeling. To constrain these models, experimental measurements of wave profiles when subjecting the material to dynamic compression are necessary. The use of a gas gun to launch a shock into a material is a traditional method to understand wave propagation and provide information of time-dependent stress variations due to complex microstructures. This data contains information on wave reverberations within a material and provides a boundary condition for simulation. Here we present measurements of the wavespeed and wave profile at the rear surface of tantalum, niobium, and a tantalum/niobium blend subjected to plate impact. Measurements of the Hugoniot elastic limit are compared to previous work and wavespeeds are compared to longitudinal sound velocity measurements to examine wave damping due to the porous microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Battery500 Consortium: Development of High-Capacity Cathodes and Robust Solid Electrolytes

The goal off this EERE-BMR-Battery 500 consortium project was to provide the supporting science and to lead the Keystone 1 project. Key findings include: identification of 1st cycle loss of high nickel NMC materials as a major opportunity to increase the capacity of these cathode materials. The selective use of substituents and surface coatings was identified as a potential way of decreasing the 1st cycle loss and in increasing capacity retention. Niobium at around the 1% level was found to be optimum. In addition, operando DSC was utilized to scope out the stability range of electrolytes developed by the Battery 500 team.

25 ENERGY STORAGE↗
DOE OSTI2022

Vapor Deposition Process for Engineering of Dispersed PEMFC ORR Pt/NbO x /C Catalysts

With support from the Department of Energy, and in partnership with Oak Ridge National Laboratory, Exothermics, Northeastern University, the University of Michigan, and IRD Fuel Cells, Ford has led an effort to use physical vapor deposition (PVD) to produce oxygen reduction reaction (ORR) catalysts for proton exchange membrane fuel cells (PEMFCs). Conventional ORR catalysts are made by wet chemical processes, and experience loss of electrochemical surface area and activity over voltage cycling due to Pt dissolution and Pt particle coalescence. Not only was PVD processing researched as a means to reduce solvent waste and enhance reproducibility in catalyst manufacturing, but it was also perceived as a means to deposit preferential phases of niobium oxide onto the catalyst, which would then serve to prevent Pt particle movement and extend PEMFC lifetime.

08 HYDROGEN↗
DOE OSTI2022

Modeling the cooldown of cryocooler conduction-cooled devices

Cryocooler conduction cooled devices can experience significant cooldown time due to lower available cooling capacity compares to convection cooled devices. Therefore, the cooldown time is an important design parameter for conduction cooled devices. This article introduces a framework developed in Python for calculating the cooldown profiles and cooldown time of cryocooler conduction-cooled devices such as superconducting magnets and accelerator cavities. The cooldown time estimation problem is essentially a system of ordinary first-order differential equations comprising the material properties (temperature dependent thermal conductivity and specific heat capacity) of the components intertwined with the prevailing heat transfer channels (conduction, radiation, and heat flow across pressed contacts) and the cryocooler capacity. The formulation of this ODE system is first presented. This ODE system is then solved using the in-built Python library odeint. A case study is presented comprising a small cryocooler conduction-cooled copper stabilized niobium-titanium magnet. The case study is supplemented with the Python script enabling the reader to simply tweak the device design parameters and optimize the design from the point of view of slow/fast cooldown.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Managing Sn-supply to tune surface characteristics of vapor-diffusion coating of Nb3Sn

Nb₃Sn promises better RF performance (Q and E_{acc}) than niobium at any given temperature because of superior superconducting properties. Nb₃Sn-coated SRF cavities are now produced routinely by growing a few microns thick Nb₃Sn films inside Nb cavities via the tin vapor diffusion technique. Sn evaporation and consumption during the growth process notably affect the quality of the coating. Aiming at favorable surface characteristics that could enhance the RF performance, many coatings were produced by varying Sn sources and temperature profiles. Coupon samples were examined using different material characterization techniques, and a selected few sets of coating parameters were used to coat 1.3 GHz single-cell cavities for RF testing. The Sn supply’s careful tuning is essential to manage the microstructure, roughness, and overall surface characteristics of the coating. We summarize the material analysis of witness samples and discuss the performance of several Nb₃Sn-coated single-cell cavities linked to Sn-source characteristics and observed Sn consumption during the film growth process.

Pudasaini, U.↗
DOE OSTI2023

Field Testing of Self-Healing Metallic Coatings for Internal Corrosion Protection of Natural Gas Pipelines

Internal corrosion occurs in natural gas pipelines primarily due to the presence of water, carbon dioxide, and hydrogen sulfide. Internal corrosion can eventually result in leakage, cracks, and rupture of the pipeline. The objective of this work is to mitigate internal corrosion in steel pipelines transporting natural gas using cold spray coatings. The corrosion behavior of carbon steel coated with self-healing zinc chromium (ZnCr) and zinc niobium (ZnNb) cold spray coatings was investigated in a natural gas environment. For comparison purposes, hot-dip galvanized steel (HDGS) was tested under the same conditions as cold spray coatings. The field test was performed at the NW Natural gas storage facility in Mist, Oregon. The field test was conducted in a 6-inch diameter pipe transporting wet natural gas out of an underground storage well at 500 psi and 4.4 °C. The coupons were tested for 15 and 32 days under stagnant and flow conditions, respectively. Weight loss method was used to measure the corrosion rate of metallic coatings. Post-corrosion surface characterization was performed on the specimen using a scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS). Crystalline phases were determined by X-ray diffraction (XRD). The field-test results confirmed that the metallic coatings provided corrosion protection of carbon steel exposed to wet natural gas under stagnant and flow conditions. The formation of the ZnCO 3 layer on top of ZnNb and ZnCr coatings led to passivation of the coatings which helps to reduce the self-corrosion. These layers form a barrier for diffusion of corrosive species to the surface.

03 NATURAL GAS↗
DOE OSTI2023

Improving Nb3Sn Cavity Performance Using Centrifugal Barrel Polishing

Nb3Sn superconducting radiofrequency (SRF) cavities have been an ongoing research topic for many years motivated by the potential for higher accelerating gradients and quality factors compared to niobium SRF cavities. The highest performing Nb3Sn cavities are manufactured using tin vapor-diffusion coating, which creates a Nb3Sn film with a surface roughness of around 100-200 nm. This is thought to be one of the limiting factors for the accelerating gradient of Nb3Sn cavities due to enhancement of magnetic field near sharp surface features. To smooth Nb3Sn SRF cavities, we have developed a mechanical polishing procedure which uses centrifugal barrel polishing to smooth the surface followed by a secondary tin coating step to repair the surface. We show that the accelerating field of a Nb3Sn SRF cavity is improved by applying this procedure. We also investigate the quench mechanism of the polished cavity by utilizing temperature mapping to measure which regions of the cavity e xperience heating during RF operation. We then cut samples from these regions and analyze the film microstructure and chemical composition in 3D using EDS and EBSD measurements together with a focused ion-beam (FIB) tomography technique.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Surface properties and RF performance of Vapor Diffused Nb3Sn on Nb after sequential anneals below 1000 °C

Nb3Sn is a next-generation superconducting material that can be used for future superconducting radiofrequency (SRF) accelerator cavities, promising better performance, cost reduction, and higher operating temperature than Nb. The Sn vapor diffusion method is currently the most preferred and successful technique to coat niobium cavi-ties with Nb3Sn. Among post-coating treatments to opti-mize the coating quality, higher temperature annealing without Sn is known to degrade Nb3Sn because of Sn loss. We have investigated Nb3Sn/Nb samples briefly annealed at 800-1000 °C for 10 and 20 minutes to poten-tially improve the surface to enhance the performance of Nb3Sn-coated cavities. Following the sample studies, a coated single-cell cavity was sequentially annealed at 900 °C and tested its performance each time, improving the cavity's quality factor relatively. This paper summarizes the sample studies and discusses the RF test results from sequentially annealed SRF Nb3Sn/Nb cavity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Two-Tone Spectroscopy of 3D SRF Cavities to Understand Two-Level System Loss

So-called two-level system (TLS) defects are among the most detrimental sources of loss and decoherence in superconducting quantum devices, and their microscopic nature still poorly understood. We develop a two-tone spectroscopy technique to characterize the spectral line width of TLS. This knowledge will help to distinguishes various types of TLS defects. In our experiments we use the fundamental TM010 pass band modes of 9-cell elliptical SRF cavities to probe spectral properties of TLS in native niobium oxide formed on the inside walls of the resonator. We pump one of the modes (4¿/9 through 8¿/9) with continuous high-power to saturate TLSs that couple to this frequency, and we probe the Q-factor of the ¿-mode. We observe increase of the quality factor of the probed ¿-mode when one of the neighboring modes is pumped. Extremely high quality factors of the pass band modes and their relative proximity in the frequency space allow us to estimate the width of the spectral hole burned in the TLS bath absorption spectrum which is related to the line spectral width of the TLS defects.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

The Evaluation of Mechanical Properties of LB650 cavities

The PIP-II project’s LB650 cavities could potentially be vulnerable to mechanical deformation because of the geometric shape of the cavity due to reduced beta. The mechanical property of the niobium half-cell was measured following various heat treatments. The 5-cell cavities were tested in a controlled drop test fashion and the real-world road test. The result showed that the 900 C heat treatment was compatible with cavity handling and transportation during production. The test provides the bases of the transportation specification and shipping container design guidelines.

Holzbauer, J.↗
DOE OSTI2023

SERAPH: Wavelike Dark Matter Searches with SRF Cavities

Haloscopes consisting of a microwave cavity with a high quality factor (Q) connected to low-noise electronics have been deployed to detect wavelike axions and dark photons. But the dark matter mass is unknown, so haloscopes must be tunable to search through the photon coupling vs. mass parameter space. Therefore, the scan rate for haloscope experiments is a crucial figure of merit and is proportional to the cavity’s quality factor. State-of-the-art experiments like ADMX currently use copper cavities with 𝑄∼80000. However, implementing superconducting cavities with 𝑄∼1010 can increase the instantaneous scan rate by possibly a factor of 105. This presentation will report progress on the SERAPH experiment, a family of superconducting haloscopes being developed by the Superconducting Quantum Materials and Systems (SQMS) Center. In this presentation, I will first discuss the principles behind operating a haloscope whose bandwidth is much narrower than the dark matter halo energy distribution. I will then describe the first SERAPH experiments implementing a 1.3 GHz Niobium cavity with an ultra-high quality factor (Q~1010) that has achieved the best sensitivity and deepest exclusion to wavelike dark photon dark matter by almost an order of magnitude. Next, I will discuss progress on the next phase of SERAPH, which will search dark photon dark matter using a widely-tunable SRF cavity (4-7 GHz). I will finally describe plans for subsequent SERAPH experiments to search for dark photons and axions with tunable SRF cavities tolerant to multi-Tesla magnetic fields and quantum sensors that subvert the Standard Quantum Limit.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Study of Cathode and Cavity Geometries in Electropolishing (EP): Electric Field Simulation

Niobium (Nb) superconducting radio frequency (SRF) cavities require electropolishing surface treatment to reach high acceleration gradient. EP performed in the plateau region of an I-V curve [1] leads to a smooth finish of the cavity surface including the equator surface. The equator surface is vital because a rough equator surface leads to premature quench and limit the cavity performance. Previous experimental work was performed to optimize EP parameters for low-beta (LB) 650 MHz Nb cavity [1]. It was found that different cathode surface areas vary the plateau onset voltage. A lower onset voltage was achieved for HB650 cavity with an enlarged cathode surface area. The aim of the study is to perform electrostatic and electrochemical simulation to understand the impact of both cavity geometry and cathodes. This report covers an initial result on electric field simulation performed with HB and LB 650 MHz cavities.

Loer, Bereket↗
DOE OSTI2023

Surface structure studies in 2D and 3D Nb resonators using GI-XRD

Superconductor radio frequency (SRF) Nb-resonators are a key element in the development of new generations of particle accelerators as well as in the fabrication of 3D circuit QED architecture for quantum computing. Nevertheless, Niobium is extremally reactive to light elements such as C, N, O and H, and therefore to the impurities ordering under special conditions, e.g., cryogenic temperatures. Since these resonators are put through a series of metallurgical and chemical processes, the number of impurities in the solid increases in tens of ppm. Upon operational conditions ~1.6 K, Nb become vulnerable to H atoms ordering, which leads to the nucleation of secondary phases such as Nb-hydrides. Thereupon to the energy dissipation and eventually to the superconductivity breakdown known as Q-disease and potentially High-Field Q-slope. In this contribution, we present a detailed structural analysis by high-energy grazing-incidence X-ray diffraction of specimens extracted from 3D Nb resonators to shed light on the kinetic formation of the resulting secondary phases and their crystal phase identification upon cooling and heating cycles. To our knowledge, this is the first study carried out in resonators samples using a light source, shallow angles and temperatures near ~4 K. Consequently, this work opens new routes to understand the chemical and phase composition, crystal and electronic structure of the Nb surface at temperatures near the operating conditions as a strategy to improve the physical and functional properties of Nb superconducting resonators.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Towards multi-qudit quantum processor using superconducting RF cavities

Superconducting radio-frequency (SRF) cavities made using high-purity Niobium can reach single photon lifetimes longer than a second with proper treatment [1]. These resonator cavities are thus an excellent choice for storing higher-dimensional quantum states. However, preparing and manipulating quantum states with larger photon numbers require a nonlinear component, like a transmon, with a sufficiently long coherence time. With the advancement in materials processing enabling coherence times for transmons exceeding hundreds of micro-seconds, one can encode and process quantum information using d-levels (qudit) of the resonators. In this talk, we will present preliminary results showing the control of a single-qudit and our progress toward building multi-qudit architecture using multi-mode SRF cavities.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

SIMS CHARACTERIZATION OF NITROGEN DOPING OF LCLS-II-HE PRODUCTION CAVITIES

The thermal diffusion of nitrogen into the surface of niobium has been shown to yield superior low-loss SRF performance. An effective solution was identified and promptly employed in the production of cryomodules for LCLS-II. With added experience and R&D, a modified process was chosen for use in the upgrade for LCLS-II-HE. Largely motivated by this circumstance, supporting research has significantly refined the technique for making calibrated secondary ion mass spectrometry (SIMS) measurements of the N concentration depth profiles produced by production processes. Standardized reference samples were included with four HE production cavities in their N-doping furnace runs. We report the calibrated dynamic SIMS depth profiles of N, C, and O for these samples, together with the cryogenic acceptance test performance of the associated cavities. Interpretation and comparison with similar samples acquired in other furnaces highlights the importance of intentional process quality control of furnace conditions.

Reece, Charles↗