Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Microstructural Investigation of VPPA–GMAW Welded 7A52 Aluminum Alloys

In this study, the microstructural features of 7A52 heat-treatable aluminum alloys welded by variable polarity plasma arc (VPPA) combined with gas metal arc welding (GMAW) (VPPA–GMAW) were investigated and compared with those of 7A52 aluminum alloys welded by GMAW. The grain structures and modification of the precipitates were analyzed by optical microscopy and transmission electron microscopy. Complementary to modification of the precipitates, the precipitation evolution in the heat-affected zone and magnesium loss in the fusion zone were measured by differential scanning calorimetry and inductively coupled plasma spectroscopy. In VPPA–GMAW, the weld only needs one pass by depositing on one side of the 10-mm-thick aluminum alloy plates because of the large penetration capability of VPPA and good fluidity of the molten metal in the weld pool. Accordingly, the effect of excessive heat input on the microstructure can be minimized. The results show that the grain growth is not obvious and the magnesium loss is small in the fusion zone of VPPA–GMAW compared with that of GMAW under the condition of equal heat input to the workpiece. Small precipitates inside the grains remain homogeneously distributed, and a large volume fraction of the η′ phase exists. The VPPA–GMAW weld exhibits less tendency to soften; thus, VPPA–GMAW is appropriate for welding thick-plate aluminum alloys with a high production rate.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural Characterization and High Strain Rate Plastic Flow Behavior of SMAW Armox500T Steel Joints from Spherical Indentation Experiments

Static indentation and uniaxial compression tests have been conducted on Armox500T steel and its weldments to predict the constraint factor (CF), i.e., ratio of Meyer’s hardness to uniaxial flow stress. Series of dynamic indentation experiments were carried out at impact velocities ranging from 5 to 300 m/s to estimate dynamic hardness as a function of average strain. Subsequently, dynamic indentation (DI) test data and CF determined under static indentation conditions have been used to study the high strain rate plastic flow behavior of Armox500T weldments in comparison with the base metal. It was observed that flow stress for Armox500T and its weldments under dynamic loading conditions (10{sup 4} s{sup −1}) are significantly higher than flow stress measured under static loading conditions (10{sup −3} s{sup −1}). The plastic flow behavior computed from DI is in good agreement with the data evaluated through conventional split Hopkinson pressure bar technique. Further, the study of the microstructure of base metal and weldments by optical microscopy and SEM revealed a considerable variation in the microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Rolling Temperature on the Microstructure and Properties of 2Cr13/316L/9Cr18MoV Stainless Steel Composite Plate Fabricated by Hot-Rolling Bonding Process

A 15-layer composite plate was developed. The microstructure and mechanical properties were characterized by scanning electron microscopy, Vickers microhardness, tensile, and bending tests. Particularly, the effects of hot-rolling at different rolling temperatures of 1130, 1180, 1250, and 1300 °C on the microstructure and mechanical properties of the 2Cr13/316L/9Cr18MoV composite plates were investigated in detail. The results indicated that, with the increase in the rolling temperature, the tensile strength was first decreased and then slightly increased by the coarsening of grains and the increase in the ferrite content in the 2Cr13 layers. The highest tensile elongation of 12.5% and tensile strength of 958.1 MPa were obtained for the composite plate manufactured with the rolling temperature of 1180 °C. The 2Cr13/316L/9Cr18MoV composite plates with rolling temperatures of 1130 and 1180 °C obtained by hot-rolling processes withstood larger bending deformations, showing only local cracks after the bending process because of their strong combined interfaces. However, during the bending to 130° of specimens fabricated with the rolling temperature of 1250 and 1300 °C, the specimens experienced direct fracture at very low bending displacements.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Nb on the Microstructure and Properties of Ti-Added Hypereutectic High-Cr Cast Iron

Effects of Nb on the microstructure and properties of Ti-added hypereutectic high-Cr cast iron were studied. With the addition of Nb, a new phase (Nb,Ti)C was formed. The microstructure analysis revealed that the amount of primary carbides was decreased from 18.6 to 8.8% and the primary and eutectic carbides were greatly refined. The decrease in the amount of primary carbides was attributed with the shrinking of primary M{sub 7}C{sub 3} phase zone in the phase diagram, while the refinement of primary carbides was attributed to the heterogeneous nucleus of (Nb,Ti)C phase for the primary M{sub 7}C{sub 3} carbides. The macrohardness of the alloy increased from 60.8 to 63.5HRC, and the impact toughness increased from 3.8 to 5.2 J cm{sup −2}. Furthermore, the wear resistance was enhanced with the addition of Nb due to the formation of hard (Nb,Ti)C carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Ratcheting Behavior of Additive Manufactured 4043 Aluminum Alloy

In this paper, 4043 aluminum alloy was printed using additive manufacturing (AM) with robot cold metal transfer (CMT) technology. The microstructure and mechanical properties of different parts, including the bottom, middle and upper portions of the printed AM 4043 aluminum alloy, were analyzed. Ratcheting tests were performed using an asymmetric load, and the tensile properties of the pre-ratcheting and un-ratcheted specimens were tested. The results indicate that the dendrites in the middle region are larger than those at the top and bottom regions and that the coarse microstructure associated with the interlayer junction resulted in the decline of the mechanical properties. The tensile strength of the AM specimens is 165 MPa, and the yield strength is 50 MPa. The printed 4043 aluminum alloy exhibits mechanical properties similar to those for conventional cast and welded aluminum alloys. The ratcheting behavior indicates that an increase in the mean stress or stress amplitude leads to an increase in the ratcheting strain, and the accumulation of ratcheting strain causes plastic damage to the materials. Pre-ratcheting behavior causes the tensile and yield strengths to increase compared to the behavior of the un-ratcheted specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Laser Shock Peening on Residual Stress, Microstructure and Hot Corrosion Behavior of Damage-Tolerant TC21 Titanium Alloy

The effect of laser shock peening (LSP) on the residual stress, microstructure and hot corrosion behavior of damage-tolerant TC21 alloy was investigated. The equilateral scanning pattern was adopted to obtain a large overlapping area for LSP. The hot corrosion experiments in a salt mixture composed of 75 wt.% Na{sub 2}SO{sub 4} + 25 wt.% NaCl at 700 and 800 °C for a total exposure of 25 h were conducted. The results demonstrated that LSP caused a high compressive residual stress with a significant increase in micro-hardness and microstructural changes in the form of crystal defects, i.e., high density dislocations. The crystal defects promoted the outward diffusion of Al, Cr and Ti to form protective mixed oxides (Al, Cr, Ti)O{sub 2}. These oxides improved the adhesion of outer oxide layer and hindered the inward diffusion of O, S and Cl, which was beneficial to improve hot corrosion resistance. The mass gains of LSP-treated specimens after hot corrosion at 700 and 800 °C were, respectively, 3.72 and 4.78 mg/cm{sup 2}, which were much lower than those of untreated specimens (5.65 and 6.81 mg/cm{sup 2}). Therefore, LSP leads to an improvement in resistance to hot corrosion of TC21 alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Initial Microstructure on Properties of Cryorolled Al 5052 Alloy Subjected to Different Annealing Treatment Temperatures

Al 5052 alloy sheets were subjected to different pre-annealing temperatures (150, 200, 250, 300, and 350 °C) prior to cryorolling. The process resulted in Al 5052 alloys with different initial microstructures. The pre-annealed alloy sheets were compared with a cryorolled sample not subjected to pre-annealing. The thicknesses of the alloy samples after cryorolling was reduced by 30%. The pre-annealed cryorolled samples exhibited low crystallite size, and high lattice strain. Among them, the cryorolled sample pre-annealed at 300 °C had the lowest crystallite size, and the highest lattice strain. Changes in initial microstructure of this sample resulted in a significant improvement in its hardness (88 Hv), tensile strength (333 MPa), and corrosion resistance. The sample had the highest corrosion resistance among the cryorolled samples.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Minor Er on the Microstructure and Properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr Alloys

As-cast Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloys containing different additions of Er were prepared. Then, the specimens were carried out homogenization heat treatment, hot rolling, cold rolling, and annealing. The effects of minor Er on the microstructure and properties of Al-6.0Mg-0.4Mn-0.1Cr-0.1Zr alloy were investigated. Results show that addition of Er can refine the microstructure and improve the mechanical properties of the alloys. As for the annealed alloys, the addition of 0.33%Er can increase the tensile strength by 29 MPa. Strength increment is mainly attributed to refinement and the precipitation of Al{sub 3}Er and Al{sub 3}(Er, Zr). Additionally, the minor Er can improve the corrosion resistance of the alloys, which can be attributed to the compact composite oxide film of Er-O and Al-O, purification, and modification.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Ti Addition on the Microstructure and Mechanical Properties of Weld Metals in HSLA Steels

Acicular ferrite (AF) can significantly improve the mechanical properties of steel welds. One practical approach to enhance the formation of AF is to provide the heterogonous nucleation sites such as Ti oxides. In this study, Ti was added to different conventional welding processes including shield metal arc welding (SMAW), submerged arc welding (SAW) and tandem SAW (T-SAW). In the SMAW process, TiO{sub 2} particles as a source of Ti were inserted into the weld groove, while in the SAW and the T-SAW processes, the Ti-enriched S2MoTB wire was used as the filler metal. The microstructural evolution of weldments was characterized by employing optical and scanning electron microscopes. In addition, microhardness (Vickers, HV), Charpy impact and tensile tests were carried out to investigate the mechanical properties of weldments. Although the microhardness measurements of all weldments did not vary significantly and were in the range of 205-252 HV, there was a considerable difference in tensile and impact properties of the SAW and the T-SAW weldments. In the SMAW process, the addition of TiO{sub 2} results in no significant enhancement in tensile and impact toughness. This can be attributed to the inhomogeneous distribution of TiO{sub 2} particles as well as the formation of large inclusions in the structure. On the other hand, Ti addition to WM increased the yield strength from 489 to 552 MPa for the SAW process, and in contrast, it decreased the impact toughness from 75 to 33 J. This detrimental effect can be related to the higher deposition of other alloying elements in the WM and the formation of more ferrite side plate phase. By applying the T-SAW process, more Ti in WM led to a higher content of AF in the microstructure and increased both yield strength and impact toughness from 528 to 595 MPa and 100 to 180 J, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Different Post-treatments on the Microstructure of EBM-Built Alloy 718

Electron beam melting (EBM) of Alloy 718 is of rapidly growing interest as it allows cost-effective production of complex components. However, the inherent flaws in the component in as-built state are of concern in view of the severe working conditions in which Alloy 718 components typically operate. The present work entails an investigation of changes in microstructure that accompany some post-treatments that are being widely considered to address defects in EBM processed Alloy 718. The effect of two different post-treatments, namely hot isostatic pressing (HIP) and a combined HIP + heat treatment (HT) carried out inside the HIP vessel, have been studied and results from as-built and post-treated specimens were compared in terms of porosity/lack-of-fusion, microstructure, phase constitution (NbC content, δ-phase) and micro-hardness. Post-treatment resulted in reduction in defect content by more than an order of magnitude. HIPing led to complete dissolution of δ phase. In comparison to as-built material, HIPed specimens exhibited significant drop in hardness. However, a sharp ‘recovery’ of hardness to yield values higher than in as-built condition was observed after HIP + HT and can be attributed to precipitation of γ′′ phase.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Property Improvement in Laser-Welded TC4 Titanium Alloy and 301L Stainless Steel Joints Without Filler Metal

Pulsed laser welding of Ti alloy to stainless steel (SS) has been applied without filler metal. When the laser beam was focused on the Ti alloy–SS interface, large volumes of Ti-Fe intermetallics were formed in the joint. These Ti-Fe intermetallics were highly brittle, causing the joint to crack spontaneously after welding. The brittle coarse Ti-Fe intermetallics seriously deteriorates the joint strength of Ti alloy and SS; therefore, it is necessary to control the quantities and distributions of brittle Ti-Fe intermetallics in the joint. The amount of melted base materials was controlled by changing laser offset to control the melted proportion and thus control the quantity and distribution of brittle Ti-Fe intermetallics in weld. When laser beam was on the SS side, melting amount of Ti alloy in weld was decreased. When laser beam was on the Ti alloy side, melting amount of SS in weld was decreased. When the laser offset was 0.35 mm away from SS side, the sample realizes the effective connection between Ti alloy and SS. A compound layer was formed at the SS side with the main microstructure of β-Ti and TiFe{sub 2}. The joint fractured at the compound layer with the maximum tensile strength of 182 MPa. Microstructures and mechanical properties of joints were improved by changing laser offset.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Annealing on the Microstructure and Properties of Electron Beam Welded 4J34 Kovar Alloy

Electron beam welding of 4J34 Kovar alloy was conducted, and the microstructure and mechanical properties of the joints in as-welded and postweld annealing treatment (PWAT) states were investigated. The martensitic transformation occurred and led to the generation of α lath martensite due to the rapid cooling in the as-welded condition. After annealing treatment, part of the α martensite transformed to γ austenite and subsequently developed the bulk γ phase and α/γ lamellar microstructures in the fusion zone (FZ) of the postwelded joint. Grains in the heat-affected zone (HAZ) clearly developed and penetrated into the FZ, causing the disappearance of the fusion line between the FZ and the HAZ. All the joints in both the as-welded and PWAT conditions exhibited ductile fracture. The maximum tensile strength of 505 MPa was obtained in the as-welded joint with the welding speed of 150 mm/min. The linear expansion coefficients of the joint and base metal decreased with the increase in temperature. However, the decreasing rate of PWAT joints was lower than that of the as-welded joints.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Effects of Heat Treatment on Microstructure and Mechanical Properties of Tribaloy 400 Coatings Deposited by Laser Cladding

The effects of heat treatment on the microstructure, microhardness, nanohardness and wear resistance of Tribaloy 400 coatings prepared by laser cladding on 304 stainless steel were studied in this paper. The results show that the microstructures of Tribaloy 400 laser cladding layer are cobalt matrix dendrites and eutectic structure. After the heat treatment at 1250 °C for 1 h, the eutectic structure disappears and the strip-like Laves phase is formed on the Co matrix. Meanwhile, the hardness is obviously improved. After the heat treatment at 1250 °C for 1 h and then 900 °C for 4 h, a small amount of ε-Co appears, the strip-like Laves phases become coarser and blunter, and some of the strip structures combine together to form blocky structures, and the hardness is decreased. The wear resistance of the samples at 600 °C is better than that at RT since the hardness of the Laves phase increases with the rise in temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Design and Development of Galvannealed Dual-Phase Steel: Microstructure, Mechanical Properties and Weldability

It was attempted to produce galvannealed dual-phase (DP) steel through a commercial continuous galvanizing line (CGL). The main challenge was to form the DP microstructure even with the slow cooling rate after annealing in the CGL. A two-pronged approach was adopted for this, viz. design of the steel chemistry with calculations and optimization of the CGL parameters with simulation using Gleeble-3800 thermomechanical simulator. The steel thus produced in CGL revealed ferrite and 18 ± 2% martensite microstructure, with tensile strength exceeding 600 MPa and 24% total elongation along with good formability. Weldability study using resistance spot welding indicated the possibility of achieving sound joint with a 4-kA width in weld time–current lobe despite the high carbon equivalence.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Solution Treatment on Microstructure Transformation, Tensile and Exfoliation Corrosion Properties of 7136 Aluminum Alloy

The effects of solution treatment on microstructure transformation and tensile properties of 7136 aluminum alloys were investigated by means of scanning electron microscopy, electron backscatter diffraction, differential scanning calorimeter, x-ray diffraction and tensile test, electrochemical evaluations, exfoliation corrosion tests, respectively. The results indicate that solution treatment had a significant effect on the microstructure transformation and tensile properties. Soluble constituents of 7136 aluminum alloys were more likely to form the η(MgZn{sub 2}) phase rather than the S(Al{sub 2}CuMg) phase. With increasing the solution temperature, the η phase was re-dissolved into the α(Al) matrix gradually. After solution treatment of 475 °C/1 h, the η phase was completely dissolved into the matrix, with insoluble Fe-rich phases remained. The dissolution of η phase would increase the strength and the corrosion resistance of the alloys. When continuing to increase the solution temperature, the recrystallized fraction increased obviously, resulting in the decrease in the strength and the corrosion resistance. Consequently, the strength and the corrosion resistance of the alloys increased firstly and then decreased with the increase in solution temperature. After solution treatment of 475 °C/1 h, the tensile strength and yield strength of the aged alloy reached their peaks, 738 and 715 MPa, respectively. The elongation of the alloy solution treated at 475 °C/1 h reached 11.2%, and its exfoliation corrosion rating got EB level. Furthermore, after the double-stage solution treatment of 450 °C/1 h + 475 °C/1 h, the recrystallized fraction decreased, resulting in a slight increase to 12.6% of the elongation, a slight increase in the corrosion resistance and a slight decrease in the strength.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Application of Selected Artificial Intelligence Methods in a System Predicting the Microstructure of Compacted Graphite Iron

Intelligent computing tools such as artificial neural network and fuzzy logic are used as predictive modeling tools. The use of these methods, combined with model experimental results, may be an excellent predictive tool, allowing us to forecast the microstructure of the tested cast iron at the level of computer simulation. In this study, the reference training cases collected in one database were used to determine the parameters of the neuro-fuzzy ANFIS model. They mainly include the results of observations and measurements of the content of individual microstructural constituents of the compacted graphite iron, examined as a function of the content of individual alloy additives (molybdenum, nickel and copper introduced in various proportions). The training process of such a fuzzy inference system is done by constantly changing its parameters (parameters of the membership function) and determining new rule conclusions as a result of presenting individual case examples from the training sample. The conducted research has shown the possibility of applying the ANFIS model as a tool to control the chemical composition of compacted graphite iron in the production of castings with high-strength parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Surface Modification of High-Carbon Steel Using Fiber Laser and Its Thermal, Microstructural and Tribological Analysis

In this study, surface modification of high-carbon steel was carried out using 2 kW fiber laser and thermal, microstructural and tribological characterizations were performed. The process parameters selected for laser surface treatment were laser power (600-1500 W) and scan speed (3000-4500 mm/min). Infrared pyrometer was used to record the surface temperature during the process. The metallographic analysis was carried out using an optical microscope to find the depth and width of the laser-treated zone. Scanning electron microscopy and energy-dispersive spectroscopy were performed to reveal the microstructure and compositional changes taking place in the laser-treated zone. It was observed that the dendritic growth took place from the top surface toward the center of the laser-treated zone. The amount of dendritic growth can be related to the maximum surface temperature generated during the process. XRD analysis indicated the formation of some intermetallic compounds and phase shifts taking place in the laser-treated zone. Residual stress analysis was performed to analyze the amount of stress accumulation in the laser-treated zone. When the temperature cycle was analyzed, it was found that the melting of the steel resulted in the formation of a surface under compressive stress while the non-melt hardened zone developed a surface under tensile stress. The maximum Vickers microhardness value achieved was about 958.8 HV{sub 0.5} for 1500 W power and 3000 mm/min scan speed. Scratch test was performed on the laser-treated track, and it was found that the hardened zone showed better tribological properties with respect to the parent material. Finally, it was observed that the surface roughness value increased with higher heat input probably due to high rate of oxide formation as well as due to the presence of martensite in the laser-treated zone.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coating on AISI1045 Steel Fabricated by Laser Cladding

AISI1045 steel is widely used in mechanical engineering. In spite of the favorable toughness and strength, the surface properties of AISI1045 steel, such as hardness, wear resistance and corrosion resistance, are not ideal. Therefore, surface modification of AISI1045 is necessary, especially for the parts suffering severe work condition. Laser cladding is a promising surface modification technology. In this work, the AlCoCrFeNiTi high-entropy alloy (HEA) coatings were prepared on the AISI1045 steel to improve its surface properties. Metallurgical bonding is obtained between the coating and the substrate. The microstructure and surface properties of the coating were characterized by scanning electron microscope, energy-dispersive spectrometry, x-ray diffraction, electrochemical workstation, microhardness tester and pin-on-ring wear tester. The microstructure of the coating produced by laser cladding is dendritic. The AlCoCrFeNiTi HEA coating is mainly composed of disordered body-centered cubic phase (Fe-Cr), ordered B2 phase (AlNi) and intermetallic phase (Ti-rich). The coating shows excellent abrasion resistance and corrosion resistance in comparison with the substrate. The maximum microhardness of the coating reaches approximately 865 HV, which is 4.5 times of AISI1045 steel.

36 MATERIALS SCIENCE↗