Results for “interface diffusion” — Page 46

DOE OSTI2024

Reconstructing the reflectivity of liquid surfaces from grazing incidence X-ray off-specular scattering data

The capillary wave model of a liquid surface predicts both the X-ray specular reflection and the diffuse scattering around it. A quantitative method is presented to obtain the X-ray reflectivity (XRR) from a liquid surface through the diffuse scattering data around the specular reflection measured using a grazing incidence X-ray off-specular scattering (GIXOS) geometry at a fixed horizontal offset angle with respect to the plane of incidence. With this approach the entire Q z -dependent reflectivity profile can be obtained at a single, fixed incident angle. This permits a much faster acquisition of the profile than with conventional reflectometry, where the incident angle must be scanned point by point to obtain a Q z -dependent profile. The XRR derived from the GIXOS-measured diffuse scattering, referred to in this paper as pseudo-reflectivity, provides a larger Q z range compared with the reflectivity measured by conventional reflectometry. Transforming the GIXOS-measured diffuse scattering profile to pseudo-XRR opens up the GIXOS method to widely available specular XRR analysis software tools. Here the GIXOS-derived pseudo-XRR is compared with the XRR measured by specular reflectometry from two simple vapor–liquid interfaces at different surface tension, and from a hexadecyltrimethylammonium bromide monolayer on a water surface. For the simple liquids, excellent agreement (beyond 11 orders of magnitude in signal) is found between the two methods, supporting the approach of using GIXOS-measured diffuse scattering to derive reflectivities. Pseudo-XRR obtained at different horizontal offset angles with respect to the plane of incidence yields indistinguishable results, and this supports the robustness of the GIXOS-XRR approach. The pseudo-XRR method can be extended to soft thin films on a liquid surface, and criteria are established for the applicability of the approach.

36 MATERIALS SCIENCE↗

DOE OSTI2022

ODD (Version 0.X)

The Orthogonal Diffusion Discretizations (ODD) library is a collection of low order (Diffusion, P1, Ray Tracing, and Variable Eddington Factor (VEF)) thermal radiation solvers for orthogonal structured grids driven by an application programing interface (API).

Cleveland, Mathew↗

NASA NTRS1978

Solidification (crystal growth) in the presence of gravitational forces

The surface tension behavior of doped and undoped InSb melts was investigated as well as their temperature and composition dependence. Surface tension in InSb melts was determined using the sessile-drop technique covering the temperature range from 530 C to 880 C. A linear regression of the data obtained shows that the temperature dependence of sigma is 392- (T-530) x (7000) plus or minus 10 dyne/cm. The d sigma/d Tau for intrinsics InSb is less than that previously reported. On the basis of the surface tension data obtained, it is concluded that surface tension induced convective flow velocities in InSb under reduced gravity conditions range from zero to at most 1 cm/sec. Accordingly, no interference with dopant segregation can be expected during growth in space because the momentum boundary layer (at the crystal melt interface) associated with any Marangoni-type convective flows would, at the given growth rate, be significantly larger than the predicted diffusion boundary layer thickness.

Gatos, H. C.↗

NASA NTRS1985

Study of the kinetics and mechanism of the thermal nitridation of SiO2

X-ray photoelectron spectroscopy (XPS) has been used to study the nitridation time and temperature dependence of the nitrogen distribution in thermally nitrided SiO2 films. The XPS data show that the maximum nitrogen concentration near the (SiO(x)N(y)/Si interface is initially at the interface, but moves 20-25 A away from the interface with increasing nitridation time. Computer modeling of the kinetic processes involved is carried out and reveals a mechanism in which diffusing species, initially consisting primarily of nitrogen, react with the substrate, followed by formation of the oxygen-rich oxynitride due to reaction of the diffusing oxygen displaced by the slower nitridation of the SiO2. The data are consistent with this mechanism provided the influence of the interfacial strain on the nitridation and oxidation kinetics is explicitly accounted for.

Vasquez, R. P.↗

NASA NTRS1991

Optical and structural characterization of InAs/GaAs quantum wells

Three InAs/GaAs single quantum wells of two-, three-, and four-monolayer thickness were characterized using optical and structural techniques. The results of high-resolution transmission electron (HRTEM) microscopy and optical studies which combine absorption, photoluminescence (PL), photoreflectance, and cathodoluminescence are presented. Using the polarization modulated absorptance technique, we observed two absorption features in our samples at 77 K. On the basis of their polarization properties and comparison with an envelope function calculation, these structures are assigned to transitions between the confined heavy-hole and confined and unconfined electron levels. Photoreflectance spectra of the three-monolayer sample in 77-300 K range show only the fundamental quantum well transition. The temperature dependence of this transition is approximately linear with a slope of 2.2 x 10 exp -4 eV/K, which is significantly lower than in both constituent materials. Comparison to the absorption data reveals that the PL spectra are affected by the carrier diffusion and therefore do not provide direct measure of the exciton density of states. The HRTEM images indicate that, while the interfaces of the two-monolayer sample are smooth and the well thickness is uniform, the four-monolayer sample has uneven interfaces and contains domains of two, three, and four monolayers.

Ksendzov, A.↗

DOE OSTI2021

Diffusion energy barrier of Au on Bi 2 Se 3 : theory and experiment

The stability and diffusion of ultra-thin thermally deposited Au films on Bi 2 Se 3 was studied using scanning tunneling microscopy and density functional theory calculations. The Au/Bi 2 Se 3 interface is of interest as gold is predicted to provide excellent electrical contact while maintaining the spin-polarized characteristics of the electronic states in Bi 2 Se 3 that make the material attractive for spintronic applications. When deposited at room temperature, Au 10 covers the surface with tightly packed islands of nanometer scale dimension. The surface morphology is stable up to 400K. At this annealing temperature, Au atoms have sufficient energy to diffuse across the surface and aggregate into larger nanostructures. At 550K, the Bi 2 Se 3 surface is only sparsely covered, and the Au has formed clusters with length scales 5-10 times larger than the original islands formed at room temperature. Comparison of the experiment and first principle calculation lead to the conclusion that the diffusion energy barrier for Au on Bi 2 Se 3 is as high as 0.47 eV, 15 which is much larger than diffusion barriers on other van der Waals materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Transport and Energetics of Carbon Dioxide in Ionic Liquids at Aqueous Interfaces

A major hurdle in utilizing carbon dioxide (CO 2 ) lies in separating it from industrial flue gas mixtures and finding suitable storage methods that enable its application in various industries. To address this issue, we utilized a combination of molecular dynamics simulations and experiments to investigate the behavior of CO 2 in common room-temperature ionic liquids (RTIL) when in contact with aqueous interfaces. Here, our investigation of RTILs, [EMIM][TFSI] and [OMIM][TFSI], and their interaction with a pure water layer mimics the environment of a previously developed ultrathin enzymatic liquid membrane for CO 2 separation. We analyzed diffusion constants and viscosity, which reveals that CO 2 molecules exhibit faster mobility within the selected ILs compared to what would be predicted solely based on the viscosity of the liquids using the standard Einstein–Stokes relation. Moreover, we calculated the free energy of translocation for various species across the aqueous–IL interface, including CO 2 and HCO 3 – . Free energy profiles demonstrate that CO 2 exhibits a more favorable partitioning behavior in the RTILs compared to that in pure water, while a significant barrier hinders the movement of HCO 3 – from the aqueous layer. Experimental measurement of the CO 2 transport in the RTILs corroborates the model. These findings strongly suggest that hydrophobic RTILs could serve as a promising option for selectively transporting CO 2 from aqueous media and concentrating it as a preliminary step toward storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2003

Flow Field Measurement of Mixing Driven by Buoyancy

Mixing driven by buoyancy-induced flows inside a cavity consists of stretching and folding of an interface. Measurement of the flow field using particle imaging velocimetry shows that during stretching the flow field has a single elliptic point, thus dominated by a single vortex. However, global bifurcation that results in folding introduces a hyperbolic point whereby the flow field degenerates to multiple vortex interactions. The short-lived coherent structure observed during mixing which results in the Rayleigh- Taylor morphology is attributed to vortex interactions. The mixing characteristics of non-homogeneous fluids driven by buoyancy are important towards understanding transport phenomenon in a microgravity environment. Mixing consists of stretching and folding of an interface due to a flow field whose intensity depends on the body force. For miscible liquids, the characteristic of the flow field determines whether mass transport is governed by diffusion or bulk stirring which induces mixing. For technologically important processes, transport of mass is governed by the coupling of the body force to scalar gradients such as concentration and or temperature' 2 3 . In order to lend insight into these classes of problems we consider a model experimental system to study mixing driven by buoyancy-induced flows. The characteristics of mixing is addressed from detail measurements of the flow field using particle imaging velocimetry (PIV), and its corresponding interface dynamics using image processing techniques.

Batur, C.↗

NASA NTRS1995

Design of a three-layer antireflection coating for high efficiency indium phosphide solar cells using a chemical oxide as first layer

It is well known that the behavior of III-V compound based solar cells is largely controlled by their surface, since the majority of light generated carriers (63% for GaAs and 79% for InP) are created within 0.2 mu m of the surface of the illuminated cell. Consequently, the always observed high surface recombination velocity (SRV) on these cells is a serious limiting factor for their high efficiency performance, especially for those with p-n junction made by either thermal diffusion or ion implantation. A good surface passivation layer, ideally a grown oxide as opposed to a deposited one, will cause a significant reduction in the SRV without adding interface problems, thus improving the performance of III-V compound based solar cells. Another significant benefit to the overall performance of the solar cells can be achieved by a substantial reduction of their large surface optical reflection by the use of a well designed antireflection (AR) coating. In this paper, we demonstrate the effectiveness of using a chemically grown thermally and chemically stable oxide, not only for surface passivation but also as an integral part of a 3-layer AR coating for thermally diffused p+n InP solar cells. A phosphorus-rich interfacial oxide, In(PO3)3, is grown at the surface of the p+ emitter using an etchant based on HNO3, o-H3PO4 and H2O2. This oxide has the unique properties of passivating the surface as well as serving as an efficient antireflective layer yielding a measured record high AMO open-circuit voltage of 890.3 mV on a thermally diffused InP(Cd,S) solar cell. Unlike conventional single layer AR coatings such as ZnS, Sb2O3, SiO or double layer AR coatings such as ZnS/MgF2 deposited by e-beam or resistive evaporation, this oxide preserves the stoichiometry of the InP surface. We show that it is possible to design a three-layer AR coating for a thermally diffused InP solar cell using the In(PO3)3 grown oxide as the first layer and Al2O3 and MgF2 as the second and third layers respectively, so as to yield an overall theoretical reflectance of less than 2%. Since chemical oxides are readily grown on III-V semiconductors materials, the technique of using the grown oxide layer to both passivate the surface as well as serve as the first of a multilayer AR coating should work well for all III-V compound-based solar cells.

Moulot, Jacques↗

NASA NTRS1995

Design of a Three-Layer Antireflection Coating for High Efficiency Indium Phosphide Solar Cells Using a Chemical Oxide as First Layer

It is well known that the behavior of III-V compound based solar cells is largely controlled by their surface, since the majority of light generated carriers (63% for GaAs and 79% for InP) are created within 0.2 microns of the illuminated surface of the cell. Consequently, the always observed high surface recombination velocity (SRV) on these cells is a serious limiting factor for their high efficiency performance, especially for those with the p-n junction made by either thermal diffusion or ion implantation. A good surface passivation layer, ideally, a grown oxide as opposed to a deposited one, will cause a significant reduction in the SRV without adding interface problems, thus improving the performance of III-V compound based solar cells. Another significant benefit to the overall performance of the solar cells can be achieved by a substantial reduction of their large surface optical reflection by the use of a well designed antireflection (AR) coating. In this paper, we demonstrate the effectiveness of using a chemically grown, thermally and chemically stable oxide, not only for surface passivation but also as an integral part of a 3- layer AR coating for thermally diffused p(+)n InP solar cells. A phosphorus-rich interfacial oxide, In(PO3)3, is grown at the surface of the p(+) emitter using an etchant based on HNO3, o-H3PO4 and H2O2. This oxide has the unique properties of passivating the surface as well as serving as a fairly efficient antireflective layer yielding a measured record high AM0, 25 C, open-circuit voltage of 890.3 mV on a thermally diffused InP(Cd,S) solar cell. Unlike conventional single layer AR coatings such as ZnS, Sb2O3, SiO or double layer AR coatings such as ZnS/MgF2 deposited by e-beam or resistive evaporation, this oxide preserves the stoichiometry of the InP surface. We show that it is possible to design a three-layer AR coating for a thermally diffused InP solar cell using the In(PO3)3 grown oxide as the first layer and Al2O3, MgF2 or ZnS, MgF2 as the second and third layers respectively, so as to yield an overall theoretical reflectance of less than 2%. Since chemical oxides are readily grown on III-V semiconductor materials, the technique of using the grown oxide layer to both passivate the surface as well as serve as the first of a multilayer AR coating, should work well for essentially all III-V compound-based solar cells.

Moulot, Jacques↗

DOE OSTI2023

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Structural and chemical evolutions of a magnesium vanadium oxide cathode under electrochemical cycling in magnesium batteries

The design of cathode materials that remain chemically and structurally stable during repetitive ion insertion and extraction poses a significant challenge in developing multivalent batteries. The cycling stability of traditional metal oxide-based cathode is challenged by sluggish diffusion of multivalent cations and parasitic reactivity at interfacial regimes, including the cathode electrolyte interphase layer (CEI). Understanding the reactions at the cathode-electrolyte interface, particularly those induced by non-stoichiometric surface layers, is a crucial design parameter for both cathode materials and electrolytes. Here, in this study, we employed multimodal analysis, including in situ and ex situ X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (TEM) and electrochemical impedance spectroscopy (EIS) to examine the surface reactions and subsequent structural and chemical evolutions of the CEI on high voltage magnesium vanadium oxide (MgV 2 O 4 ) spinel cathode during the Mg 2+ insertion/extraction processes. The results revealed that the presence of non-stoichiometric surface layers in the magnesium vanadium oxide cathode drive the decomposition of bis(trifluoromethanesulfonyl)imide (TFSI - ) anion, leading to the formation of the CEI layer. The CEI layer could inhibit the Mg 2+ ion transfer processes. Accompanying this reactivity-driven degradation, the magnesium vanadium oxide cathode undergoes pulverization, forming clusters of nanosized particles. This process likely improves cycling ability by creating new intercalation sites and shortening the diffusion pathway for the Mg 2+ cations. This study demonstrates that controlling surface stoichiometry and engineering morphological properties are critical design parameters for high performance cathodes for multivalent batteries.

25 ENERGY STORAGE↗

NASA NTRS1993

A solar dynamo surface wave at the interface between convection and nonuniform rotation

A simple dynamo surface wave is presented to illustrate the basic principles of a dynamo operating in the thin layer of shear and suppressed eddy diffusion beneath the cyclonic convection in the convection zone of the sun. It is shown that the restriction of the shear delta(Omega)/delta(r) to a region below the convective zone provides the basic mode with a greatly reduced turbulent diffusion coefficient in the region of strong azimuthal field. The dynamo takes on the character of a surface wave tied to the lower surface z = 0 of the convective zone. There is a substantial body of evidence suggesting a fibril state for the principal flux bundles beneath the surface of the sun, with fundamental implications for the solar dynamo.

Parker, E. N.↗

DOE OSTI2022

The effect of saturated thermal conduction on clouds in a hot plasma

We numerically investigate the internal evolution of multiphase clouds, which are at rest with respect to an ambient, highly ionized medium (HIM) representing the hot component of the circumgalactic medium. Time-dependent saturated thermal conduction and its implications like condensation rates and mixing efficiency are assessed in multiphase clouds. Our simulations are carried out by using the adaptive mesh refinement code FLASH. The model clouds are initially in both hydrostatic and thermal equilibrium and are in pressure balance with the HIM. Thus, they have steep gradients in both temperature and density at the interface to HIM leading to non-negligible thermal conduction. Several physical processes are considered numerically or semi-analytically: thermal conduction, radiative cooling and external heating of gas, self-gravity, mass diffusion, and dissociation of molecules and ionization of atoms. It turns out that saturated thermal conduction triggers a continuous condensation irrespective of cloud mass. Dynamical interactions with ambient HIM all relate to the radial density gradient in the clouds: (1) mass flux due to condensation is the higher the more homogeneous the clouds are; (2) mixing of condensed gas with cloud gas is easier in low-mass clouds, because of their shallower radial density gradient; and thus (3) accreted gas is distributed more efficiently. A distinct and sub-structured transition zone forms at the interface between cloud and HIM, which starts at smaller radii and is much narrower as deduced from analytical theory.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1989

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2020

Nonoverlapping Localized Exponential Time Differencing Methods for Diffusion Problems

In this paper, we propose nonoverlapping localized exponential time differencing (ETD) methods for diffusion problems. The model time-dependent diffusion equation is first reformulated on subdomains based on the nonoverlapping domain decomposition, in which Neumann boundary conditions are imposed on the interfaces for the subdomain problems and Dirichlet type conditions are enforced to form a space-time interface problem. After spatial discretization by standard central finite differences and temporal integration with the first or second order ETD methods, the fully discrete interface problem is obtained. Such an interface problem is then solved iteratively either at each time step or over the whole time interval: the former involves the solution of stationary problems in each subdomain at each iteration while the latter involves the solution of time-dependent subdomain problems at each iteration. For both approaches, we prove that localized ETD solutions conserve mass exactly and converge in time to the exact space semidiscrete solution. Numerical experiments in two dimensions are also presented to illustrate the performance of the proposed methods.

Mass conservation↗