Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “information services”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Data Communications Performance of AOCDL and AUTOMET Over a VDL Mode 2 Link

Airline Operational Control Data Link (AOCDL) is a service that allows for downlink of in-flight data to help an airline operate efficiently. Automated Meteorological Transmission (AUTOMET) is a weather reporting system that provides forecasts and atmospheric conditions to pilots during flight. These are two examples of new or extended services that will be enabled by implementation of the ATN and its digital air/ground communications data links. One of the possible data links identified for these services is VDL Mode 2. This research focuses on the data link performance of AOCDL and AUTOMET services in a 2015 scenario using VDL Mode 2 as the data link. In the near term, it is expected that the Controller-Pilot Data Link Communication (CPDLC) and Decision Support System Data Link (DSSDL) services will also use the VDL Mode 2 link. CPDLC and DSSDL are high-priority services that communicate aircraft control information and require low end-to-end delays for safety. VDL Mode 3, which is the preferred link for these services because it provides priority-based link access, will not be deployed in time for earlier implementations of these services to use. As such, the research also investigates the impact of CPDLC and DSSDL services on the same VDL link as AOCDL and AUTOMET. Performance of these services over the data link will be separately examined for the airport, terminal, and en route domains. OPNET simulations are performed for each domain. The number of aircraft for each domain is representative of the expected peak aircraft in 2015. Results are collected during a steady-state condition, with aircraft neither entering nor exiting the domain. The study explores the services in terms of the traffic load they present to the VDL Mode 2 radio. The amount of load each service contributes to the data link will be shown for each domain. The end-to-end delays for each service will be discussed. Data link metrics such as subnetwork and queuing delays, channel utilization, and protocol overhead will be used to show the impact of these services on VDL Mode 2. All results will be presented both with and without the inclusion of CPDLC and DSSDL services.

Bretmersky, Steven↗

Aggregation Tool to Create Curated Data albums to Support Disaster Recovery and Response

Despite advances in science and technology of prediction and simulation of natural hazards, losses incurred due to natural disasters keep growing every year. Natural disasters cause more economic losses as compared to anthropogenic disasters. Economic losses due to natural hazards are estimated to be around $6-$10 billion dollars annually for the U.S. and this number keeps increasing every year. This increase has been attributed to population growth and migration to more hazard prone locations such as coasts. As this trend continues, in concert with shifts in weather patterns caused by climate change, it is anticipated that losses associated with natural disasters will keep growing substantially. One of challenges disaster response and recovery analysts face is to quickly find, access and utilize a vast variety of relevant geospatial data collected by different federal agencies such as DoD, NASA, NOAA, EPA, USGS etc. Some examples of these data sets include high spatio-temporal resolution multi/hyperspectral satellite imagery, model prediction outputs from weather models, latest radar scans, measurements from an array of sensor networks such as Integrated Ocean Observing System etc. More often analysts may be familiar with limited, but specific datasets and are often unaware of or unfamiliar with a large quantity of other useful resources. Finding airborne or satellite data useful to a natural disaster event often requires a time consuming search through web pages and data archives. Additional information related to damages, deaths, and injuries requires extensive online searches for news reports and official report summaries. An analyst must also sift through vast amounts of potentially useful digital information captured by the general public such as geo-tagged photos, videos and real time damage updates within twitter feeds. Collecting and aggregating these information fragments can provide useful information in assessing damage in real time and help direct recovery efforts. The search process for the analyst could be made much more efficient and productive if a tool could go beyond a typical search engine and provide not just links to web sites but actual links to specific data relevant to the natural disaster, parse unstructured reports for useful information nuggets, as well as gather other related reports, summaries, news stories, and images. This presentation will describe a semantic aggregation tool developed to address similar problem for Earth Science researchers. This tool provides automated curation, and creates "Data Albums" to support case studies. The generated "Data Albums" are compiled collections of information related to a specific science topic or event, containing links to relevant data files (granules) from different instruments; tools and services for visualization and analysis; information about the event contained in news reports, and images or videos to supplement research analysis. An ontology-based relevancy-ranking algorithm drives the curation of relevant data sets for a given event. This tool is now being used to generate a catalog of Hurricane Case Studies at Global Hydrology Resource Center (GHRC), one of NASA's Distribute Active Archive Centers. Another instance of the Data Albums tool is currently being created in collaboration with NASA/MSFC's SPoRT Center, which conducts research on unique NASA products and capabilities that can be transitioned to the operational community to solve forecast problems. This new instance focuses on severe weather to support SPoRT researchers in their model evaluation studies

Ramachandran, Rahul↗

[The Engineering and Technical Services Directorate at the Glenn Research Center]

My name is James Moon and I am a senior at Tennessee State University where my major is Aeronautical and Industrial Technology with a concentration in industrial electronics. I am currently serving my internship in the Engineering and Technical Services Directorate at the Glenn Research Center (GRC). The Engineering and Technical Service Directorate provides the services and infrastructure for the Glenn Research Center to take research concepts to reality. They provide a full range of integrated services including engineering, advanced prototyping and testing, facility management, and information technology for NASA, industry, and academia. Engineering and Technical Services contains the core knowledge in Information Technology (IT). This includes data systems and analysis, inter and intranet based systems design and data security. Including the design and development of embedded real-time s o h a r e applications for flight and supporting ground systems, Engineering and Technical Services provide a wide range of IT services and products specific to the Glenn Research Center research and engineering community. In the 7000 Directorate I work directly in the 7611 organization. This organization is known as the Aviation Environments Technical Branch. My mentor is Vincent Satterwhite who is also the Branch Chief of the Aviation Environments Technical Branch. In this branch, I serve as the Assistant program manager of the Engineering Technology Program. The Engineering Technology Program (ETP) is one of three components of the High School L.E.R.C.I.P. This is an Agency-sponsored, eight-week research-based apprenticeship program designed to attract traditionally underrepresented high school students that demonstrate an aptitude for and interest in mathematics, science, engineering, and technology.

Moon, James↗

Data Quality Challenges for Analysis Ready Data (ARD)

Data quality plays a critical role in research and applications. The Earth Science Information Partners (ESIP) Information Quality Cluster (IQC) defines four aspects of information quality: Science, Product, Stewardship, and Services. The ESIP IQC has become internationally recognized as an authoritative and responsive resource of information and guidance to data producers and distributors on how to implement data quality standards and best practices for their science data systems, datasets, and data/metadata dissemination services. In recent years, cloud computing environments have provided scale-up capabilities such as data archives and services, enabling interdisciplinary science and applications. More value-added products are expected from data service providers, including Analysis Ready Data (ARD). ARD refers to data that has been preprocessed into a form that allows immediate analysis by the end user, processed to a minimum set of requirements and provides interoperability over time and across multiple datasets. Once a dataset has been developed from its original form to produce ARD, what quality characteristics should the derived dataset or ARD possess? Also, is it safe to assume that the quality of the ARD is consistent with the quality of the source data, or are there special attributes to an ARD that would warrant a secondary, independent quality assessment? What provenance (also called “data lineage”) information needs to be included in ARD? It is important to answer these questions, especially given the ease of use of ARD, and the consequent temptation by users to trust ARD without understanding the limitations or possible variations in quality compared to the source data. In this presentation, we will discuss data quality challenges for ARD products and services and introduce IQC for participation.

data quality↗

Space Radiation Effects Laboratory

The SREL User's Handbook is designed to provide information needed by those who plan experiments involving the accelerators at this laboratory. Thus the Handbook will contain information on the properties of the machines, the beam parameters, the facilities and services provided for experimenters, etc. This information will be brought up to date as new equipment is added and modifications accomplished. This Handbook is influenced by the many excellent models prepared at other accelerator laboratories. In particular, the CERN Synchrocyclotron User's Handbook (November 1967) is closely followed in some sections, since the SREL Synchrocyclotron is a duplicate of the CERN machine. We wish to thank Dr. E. G. Michaelis for permission to draw so heavily on his work, particularly in Section II of this Handbook. We hope that the Handbook will prove useful, and will welcome suggestions and criticism.

Source record↗

Advances Made in the Next Generation of Satellite Networks

Because of the unique networking characteristics of communications satellites, global satellite networks are moving to the forefront in enhancing national and global information infrastructures. Simultaneously, broadband data services, which are emerging as the major market driver for future satellite and terrestrial networks, are being widely acknowledged as the foundation for an efficient global information infrastructure. In the past 2 years, various task forces and working groups around the globe have identified pivotal topics and key issues to address if we are to realize such networks in a timely fashion. In response, industry, government, and academia undertook efforts to address these topics and issues. A workshop was organized to provide a forum to assess the current state-of-the-art, identify key issues, and highlight the emerging trends in the next-generation architectures, data protocol development, communication interoperability, and applications. The Satellite Networks: Architectures, Applications, and Technologies Workshop was hosted by the Space Communication Program at the NASA Lewis Research Center in Cleveland, Ohio. Nearly 300 executives and technical experts from academia, industry, and government, representing the United States and eight other countries, attended the event (June 2 to 4, 1998). The program included seven panels and invited sessions and nine breakout sessions in which 42 speakers presented on technical topics. The proceedings covers a wide range of topics: access technology and protocols, architectures and network simulations, asynchronous transfer mode (ATM) over satellite networks, Internet over satellite networks, interoperability experiments and applications, multicasting, NASA interoperability experiment programs, NASA mission applications, and Transmission Control Protocol/Internet Protocol (TCP/IP) over satellite: issues, relevance, and experience.

Bhasin, Kul B.↗

State-of-the-Art: Small Spacecraft Technology

When the first edition of NASA’s Small Spacecraft Technology State-of-the-art report was published in 2013, 247 CubeSats and 105 other non-CubeSat small spacecraft under 50 kilograms (kg) had been launched worldwide, representing less than 2% of launched mass into orbit over multiple years. In 2013 alone, around 60% of the total spacecraft launched had a mass under 600 kg, and of those under 600 kg, 83% were under 200 kg and 37% were nanosatellites (1). Of the total 1,849 spacecraft launched in 2021, 94% were small spacecraft with an overall mass under 600 kg, and of those under 600 kg, 40% were under 200 kg, and 11% were nanosatellites (1). Since 2013, the fight heritage for small spacecraft has increased by over 30% and has become the primary source to space access for commercial, government, private, and academic institutions. The total number of spacecraft launched in the past 10 years is 5,681 and 45% of those had a mass. As with all previous editions of this report, the 2022 edition captures and distills a wealth of new information available on small spacecraft systems from NASA and other publicly available sources. This report is limited to publicly available information and cannot reflect major advances in development that are not publicly disclosed. We encourage any opportunity to publish mission outcomes and technology development milestones (e.g., via conference papers, press releases, company website) so they can be reflected in this report. Overall, this report is a survey of small spacecraft technologies sourced from open literature; it does not endeavor to be an original source, and only considers literature in the public domain to identify and classify devices. Commonly used sources for data include manufacturer datasheets, press releases, conference papers, journal papers, public filings with government agencies, news articles, presentations, the compendium of databases accessed via NASA’s Small Spacecraft Systems Virtual Institute (S3VI) Information Search, and engagement with companies. Data not appropriate for public dissemination, such as proprietary, export controlled, or otherwise restricted data, are not considered. As a result, this report includes many dedicated hours of desk research performed by subject matter experts reviewing resources noted above. Content in this 2022 edition is based on data available by October 2022. This report should not be considered as a comprehensive overview of all the technologies but a great reference for the current state-of-the-art SmallSat technologies. The organizational approach for each chapter is relatively consistent with previous editions and includes an introduction of the technology, current development status of the technology’s procurable systems, and summary tables of technologies surveyed. The content in each chapter is uniquely organized to present a mini-stand-alone report on spacecraft subsystems. As in previous years, chapters include information from previous editions but are updated with new and maturating technologies and reference missions. Tables in each section provide a convenient summary of the technologies discussed, with explanations and references in the body text. The authors have attempted to isolate trends in the small spacecraft industry to point out which technologies have been adopted after successful demonstration missions. Lastly, the authors tried to use the terms “SmallSat,” “microsatellite,” “nanosatellite,” and “CubeSat” in a consistent manner, even as these terms are often used interchangeably in the space industry. Every subsystem chapter contains updated information to reflect the growth in the small spacecraft market. Significant changes are included in several chapters. The “Complete Spacecraft Platforms” chapter now includes information on the two main market options, hosted payload services and dedicated buses. The “Power” chapter provides information on the development of solid-state batteries with significantly higher energy than the current state-of-theart lithium-ion batteries. A large effort was made to update the “Communications” chapter to appropriately capture the recent technology maturation of optical communications for SmallSats. The “Ground Data Systems and Mission Operations” chapter was updated to reflect the recent establishment of the Near Space Network and influx of SmallSat Optical Ground Stations. The “Guidance, Navigation and Control” chapter was updated to include Lidar sensor technology. The “Deorbit Systems” chapter includes a discussion of recently proposed changes by the Federal Communications Commission (FCC) to limit a spacecraft’s lifetime to no longer than 5 years after end-of-mission. The “Identification and Tracking” Chapter includes updated information on the progress of SmallSat tracking. Finally, this report now encompasses technology funded by NASA’s Small Spacecraft Technology (SST) program’s SmallSat Technology Partnerships (STP) initiative which is described further in this Introduction. The reader can find the included SST technology in the “On the Horizon” section of the “Thermal Systems”, “Communications”, and “Guidance, Navigation, and Control” chapters. A central element of this report is to list state-of-the-art technologies by NASA standard Technology Readiness Level (TRL) as defined by the 2020 NASA Engineering Handbook, found in NASA NPR 7123.1C NASA Systems Engineering Processes and Requirements. The authors have endeavored to independently verify the TRL value of each technology by reviewing and citing published test results or publicly available data to the best of their ability. Where test results and data disagree with vendors’ own advertised TRL, the authors have attempted to engage the vendors to discuss the discrepancy. Readers are strongly encouraged to follow the references cited in the literature describing the full performance range and capabilities of each technology. Readers of this report should reach out to individual companies to further clarify information. It is important to note that this report takes a broad system-level view. To attain a high TRL, the subsystem must be in a flight-ready configuration with all supporting infrastructure—such as mounting points, power conversion, and control algorithms—in an integrated unit. An accurate TRL assessment requires a high degree of technical knowledge on a subject device, and an in-depth understanding of the mission (including interfaces and environment) on which the device was flown. There is variability in TRL values depending on design factors for a specific technology. For example, differences in TRL assessment based on the operating environment may result from the thermal environment, mechanical loads, mission duration, or radiation exposure. If a technology has flown on a mission without success, or without providing valid confirmation to the operator, such claimed “flight heritage” was discounted. The authors believe TRLs are most accurately determined when assessed within the context of a program’s unique requirements. While the overall capability of small spacecraft has matured since the 2021 edition of this report, technologies are still being developed to make deep space SmallSat missions more routine and more cost effective. Future editions of this report may include content dedicated to the rapidly growing fields of assembly, integration, and testing services, and mission modeling and simulation–all of which are now extensively represented at small spacecraft conferences. Many of these subsystems and services are still in their infancy, but as they evolve and reliable conventions and standards emerge, the next iteration of this report may also evolve to include additional chapters.

Bruce Yost↗

Creation of a ceramics handbook

A group of common ceramic materials (alumina, magnesium oxide, silicon nitride, and silicon carbide) were characterized through literature searches according to their physical properties. The files used were the NASA file, DDC/GRA File, Engineering Index File and standard library searches. The results of these searches are arranged by material properties including mechanical, electrical, electromagnetic, where applicable, and fracture; and the entries are arranged in chronological order by candidate. A list, by author, follows where tabular information including charts and figures of results is given along with a brief statement of the results and conclusions. In both cases, information on the independent variables along with their range is given. The results of an extensive industry survey asking for names of other candidates on which information is lacking and also what type of service, if any, is desired in keeping a current information file on general ceramic materials.

Craft, W. J.↗

The NASA Scientific and Technical Information Program: Exploring challenges, creating opportunities

The NASA Scientific and Technical Information (STI) Program offers researchers access to the world's largest collection of aerospace information. An overview of Program activities, products and services, and new directions is presented. The R&D information cycle is outlined and specific examples of the NASA STI Program in practice are given. Domestic and international operations and technology transfer activities are reviewed and an agenda for the STI Program NASA-wide is presented. Finally, the incorporation of Total Quality Management and evaluation metrics into the STI Program is discussed.

Sepic, Ronald P.↗

Information Searching in the Residential Solar PV Market

This paper examines the consumer information search behavior of households in San Diego County with solar photovoltaic (PV) systems. We focus on whether solar PV households financing the technology through third-party ownership (TPO) versus host-ownership (HO), which is equivalent to leasing or buying goods in other markets, have heterogeneous preferences as reflected by information search. Conditional on adoption, we find that TPO households tend to seek more information on home modifications required for solar installation whereas HO households seek more information on the financial returns of solar investments. These preferences may be correlated with the consumption of other goods and services, and thus, if used to inform marketing strategies, our results could help reduce solar PV customer acquisition costs and accelerate technology diffusion. They also have indirect implications for marketing goods and services in other contexts where consumers exhibit similar preferences.

California↗

Optimal reblocking as a practical tool for neighborhood development

Fast urbanization is a common feature of many developing human societies. In many cases, past and present, explosive population growth in cities outstrips the rate of provision of housing and urban services and leads to the formation of informal settlements or slums. Slums are extremely varied in terms of their histories, infrastructure, and rates of change, but they share certain common features: informal land use, lack of physical accesses, and nonexistent or poor quality urban services. Currently, about 1 billion people worldwide live in slums, a number that could triple by 2050 if no practical solutions are enacted to reverse this trend. Underlying most problems of slums is the issue of lack of physical accesses to places of work and residence. This prevents residents and businesses from having an address, obtaining basic services such as water and sanitation, and being helped in times of emergency. In this paper, we show how the physical layout of any neighborhood can be classified quantitatively in terms of its access topology in a way that is independent of its geometry. Topological indices capturing levels of access to structures within a city block can then be used to define a constrained optimization problem, whose solution generates an access network that makes each structure in the settlement accessible to services with minimal disruption and cost. We discuss the general applicability of these techniques to several informal settlements in developing cities and demonstrate various technical aspects of our solutions. In conclusion, we discuss how these techniques could be used on a large scale to speed up human development processes in cities throughout the world while respecting their local identity and history.

54 ENVIRONMENTAL SCIENCES↗

Explicit modeling of abiotic and landscape factors reveals precipitation and forests associated with aphid abundance

Abstract Increases in natural or noncrop habitat surrounding agricultural fields have been shown to be correlated with declines in insect crop pests. However, these patterns are highly variable across studies suggesting other important factors, such as abiotic drivers, which are rarely included in landscape models, may also contribute to variability in insect population abundance. The objective of this study was to explicitly account for the contribution of temperature and precipitation, in addition to landscape composition, on the abundance of a widespread insect crop pest, the soybean aphid ( Aphis glycines Matsumura), in Wisconsin soybean fields. We hypothesized that higher soybean aphid abundance would be associated with higher heat accumulation (e.g., growing degree days) and increasing noncrop habitat in the surrounding landscape, due to the presence of the overwintering primary hosts of soybean aphid. To evaluate these hypotheses, we used an ecoinformatics approach that relied on a large dataset collected across Wisconsin over a 9‐year period (2003–2011), for an average of 235 sites per year ( n = 2,110 fields total). We determined surrounding landscape composition (1.5‐km radius) using publicly available satellite‐derived land cover imagery and interpolated daily temperature and precipitation information from the National Weather Service COOP weather station network. We constructed linear mixed models for soybean aphid abundance based on abiotic and landscape explanatory variables and applied model averaging for prediction using an information theoretic framework. Over this broad spatial and temporal extent in Wisconsin, we found that variation in growing season precipitation was positively related to soybean aphid abundance, while higher precipitation during the nongrowing season had a negative effect on aphid populations. Additionally, we found that aphid populations were higher in areas with proportionally more forest but were lower in areas where minor crops, such as small grains, were more prevalent. Thus, our findings support our hypothesis that including abiotic drivers increases our understanding of crop pest abundance and distribution. Moreover, by explicitly modeling abiotic factors, we may be able to explore how variable climate in tandem with land cover patterns may affect current and future insect populations, with potentially critical implications for crop yields and agricultural food webs.

Stack Whitney, Kaitlin↗

Cockpit weather information system

Weather information, periodically collected from throughout a global region, is periodically assimilated and compiled at a central source and sent via a high speed data link to a satellite communication service, such as COMSAT. That communication service converts the compiled weather information to GSDB format, and transmits the GSDB encoded information to an orbiting broadcast satellite, INMARSAT, transmitting the information at a data rate of no less than 10.5 kilobits per second. The INMARSAT satellite receives that data over its P-channel and rebroadcasts the GDSB encoded weather information, in the microwave L-band, throughout the global region at a rate of no less than 10.5 KB/S. The transmission is received aboard an aircraft by means of an onboard SATCOM receiver and the output is furnished to a weather information processor. A touch sensitive liquid crystal panel display allows the pilot to select the weather function by touching a predefined icon overlain on the display's surface and in response a color graphic display of the weather is displayed for the pilot.

Tu, Jeffrey Chen-Yu↗

Utility Energy Services Contracts: Enabling Documents

The Federal Energy Management Program's 'Utility Energy Service Contracts: Enabling Documents' provide legislative information and materials that clarify the authority for federal agencies to enter into utility energy service contracts, or UESCs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Quantifying and Understanding the Access Time to Dockless Micromobility: A Case Study in Washington, D.C.

Micromobility has been widely deployed in many cities. Similar as how access time/distance affects the travel demand to use public transit and informs transit system design, access time/distance to micromobility service measures its service efficiency and also serves as an equity indicator to inform city agencies from a regulation perspective. Though there is an increasing need to understand it, access to micromobility has not been sufficiently studied. This paper developed a framework to quantity the access time to dockless micromobility service (i.e., the minimum time needed to walk to reach the closest dockless micromobility vehicles). Based on the real-time vehicle location data collected from Washington, DC, this research quantified the access time to dockless micromobility, analyzed its spatial and temporal variation patterns and investigated its relationship with socio-demographic variables (i.e., population density, employment density and low-income population). The results revealed that the access time to dockless micromobility ranges between 0 to 4 minutes with the most frequently observed range of 0.5 to 1 minutes, and the city center area tends to have shorter access time than the outskirts areas. Results also indicate a quite stable access time level in DC with access time standard deviation of 0.2 to 0.5 minutes. After correlating the access time at census-block-group level with socio-demographic data, it was discovered that shorter access time usually aligns with larger population and employment density, and the proportion of low-income population was found not helpful with explaining the access time variation, which indicating a relatively equitable micromobility program.

access time↗

Strategies for Fault Tolerance in Multicomponent Applications

This paper discusses on-going work with the Integrated Plasma Simulator (IPS), a framework for coupled multiphysics simulations of plasmas, to allow simulations to run through the loss of nodes on which the simulation is executing. While many different techniques are available to improve the fault tolerance of computational science applications on high-performance computer systems, checkpoint/restart (C/R) remains virtually the only one that see widespread use in practice. Our focus here is to augment the traditional C/R approach with additional techniques that can provide a more localized and tailored response to faults based on the ability to restart failed tasks on an individual basis, and the use of information external to the application itself in order to guide decision-making, in many cases avoiding the need to stop and restart the entire simulation. This capability involves several features within the IPS framework, and leverages the Fault Tolerance Backplane, a publish/subscribe event service to disseminate fault-related information throughout HPC systems, to obtain information from the Reliability, Availability and Serviceability (RAS) subsystem of the HPC system. This work is described in the context of Cray XT-series computer systems for concreteness, but is applicable to other environments as well. As part of the analysis of this work, we discuss the requirements to generalize this approach to other complex simulation applications beyond the Integrated Plasma Simulator.

99 GENERAL AND MISCELLANEOUS↗

AASG Wells Data for the EGS Test Site Planning and Analysis Task

Temperature measurement data obtained from boreholes for the Association of American State Geologists (AASG) geothermal data project. Typically bottomhole temperatures are recorded from log headers, and this information is provided through a borehole temperature observation service for each state. Service includes header records, well logs, temperature measurements, and other information for each borehole. Information presented in Geothermal Prospector was derived from data aggregated from the borehole temperature observations for all states. For each observation, the given well location was recorded and the best available well identifier (name), temperature and depth were chosen. The "Well Name Source," "Temp. Type" and "Depth Type" attributes indicate the field used from the original service. This data was then cleaned and converted to consistent units. The accuracy of the observation's location, name, temperature or depth was note assessed beyond that originally provided by the service. Bottom hole temperature datasets from the AASG were downloaded from repository.usgin.org between May 16 and May 24, 2013. The data were cleaned to remove null and non-real entries, and units were standardized across all datasets. When selecting key attributes, specific criteria were used to determine the best available values. For temperature, corrected temperature was preferred, followed by measured temperature. For depth, depth of measurement was prioritized, with true vertical depth and driller total depth used as alternatives. Well identification was assigned based on the API number when available, followed by the well name, with the observation URI used as a last option.

15 GEOTHERMAL ENERGY↗

Support of an Active Science Project by a Large Information System: Lessons for the EOS Era

The ability of large information systems to support the changing data requirements of active science projects is being tested in a NASA collaborative study. This paper briefly profiles both the active science project and the large information system involved in this effort and offers some observations about the effectiveness of the project support. This is followed by lessons that are important for those participating in large information systems that need to support active science projects or that make available the valuable data produced by these projects. We learned in this work that it is difficult for a large information system focused on long term data management to satisfy the requirements of an on-going science project. For example, in order to provide the best service, it is important for all information system staff to keep focused on the needs and constraints of the scientists in the development of appropriate services. If the lessons learned in this and other science support experiences are not applied by those involved with large information systems of the EOS (Earth Observing System) era, then the final data products produced by future science projects may not be robust or of high quality, thereby making the conduct of the project science less efficacious and reducing the value of these unique suites of data for future research.

Angelici, Gary L.↗