Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gravity station”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Moonquakes.

Although the average rate of seismic energy release within the moon appears to be far below that of the earth, over 100 events believed to be moonquakes have been recorded by the two seismic stations installed on the lunar surface during Apollo missions 12 and 14. With few exceptions, the moonquakes occur at monthly intervals near times of perigee and apogee and show correlations with the longer-term (7-month) lunar gravity variations. The repeating moonquakes are believed to occur at not less than 10 different locations. However, a single focal zone accounts for 80 per cent of the total seismic energy detected. This active zone appears to be 600 kilometers south-southwest of the Apollo 12 and 14 sites and deep within the moon. Each focal zone must be small (less than 10 kilometers in linear dimension) and fixed in location over a 14-month period. Cumulative strain at each location is inferred. Thus, the moonquakes appear to be releasing internal strain of unknown origin, the release being triggered by tidal stresses.

Latham, G.↗
NASA NTRS1974

A simulation of the San Andreas fault experiment

The San Andreas fault experiment (Safe), which employs two laser tracking systems for measuring the relative motion of two points on opposite sides of the fault, has been simulated for an 8-yr observation period. The two tracking stations are located near San Diego on the western side of the fault and near Quincy on the eastern side; they are roughly 900 km apart. Both will simultaneously track laser reflector equipped satellites as they pass near the stations. Tracking of the Beacon Explorer C spacecraft has been simulated for these two stations during August and September for 8 consecutive years. An error analysis of the recovery of the relative location of Quincy from the data has been made, allowing for model errors in the mass of the earth, the gravity field, solar radiation pressure, atmospheric drag, errors in the position of the San Diego site, and biases and noise in the laser systems. The results of this simulation indicate that the distance of Quincy from San Diego will be determined each year with a precision of about 10 cm. Projected improvements in these model parameters and in the laser systems over the next few years will bring the precision to about 1-2 cm by 1980.

Agreen, R. W.↗
NASA NTRS1987

Long term orbital storage of cryogenic propellants for advanced space transportation missions

A comprehensive study has developed the major features of a large capacity orbital propellant depot for the space-based, cryogenic OTV. The study has treated both the Dual-Keel Space Station and co-orbiting platforms as the accommodations base for the propellant storage facilities, and trades have examined both tethered and hard-docked options. Five tank set concepts were developed for storing the propellants, and along with layout options for the station and platform, were evaluated from the standpoints of servicing, propellant delivery, boiloff, micrometeoroid/debris shielding, development requirements, and cost. These trades led to the recommendation that an all-passive storage concept be considered for the platform and an actively refrigerated concept providing for reliquefaction of all boiloff be considered for the Space Station. The tank sets are modular, each storing up to 45,400 kg of LO2/LH2, and employ many advanced features to provide for microgravity fluid management and to limit boiloff. The features include such technologies as zero-gravity mass gauging, total communication capillary liquid acquisition devices, autogenous pressurization, thermodynamic vent systems, thick multilayer insulation, vapor-cooled shields, solar-selective coatings, advanced micrometeoroid/debris protection systems, and long-lived cryogenic refrigeration systems.

Schuster, John R.↗
NASA NTRS1989

Fire safety applications for spacecraft

Fire safety for spacecraft is reviewed by first describing current practices, many of which are adapted directly from aircraft. Then, current analyses and experimental knowledge in low-gravity combustion, with implications for fire safety are discussed. In orbiting spacecraft, the detection and suppression of flames are strongly affected by the large reduction in buoyant flows under low gravity. Generally, combustion intensity is reduced in low gravity. There are some notable exceptions, however, one example being the strong enhancement of flames by low-velocity ventilation flows in space. Finally, the future requirements in fire safety, particularly the needs of long-duration space stations in fire prevention, detection, extinguishment, and atmospheric control are examined. The goal of spacecraft fire-safety investigations is the establishment of trade-offs that promote maximum safety without hampering the useful human and scientific activities in space.

Friedman, Robert↗
NASA NTRS1999

Gravity and space flight: effects on nutritional status

The final decade of the millennium has seen an enormous amount of on-orbit life sciences research, including both short- and long-duration flight research. Life sciences dedicated Space Shuttle flights have made intensive research opportunities available to study on the acute adaptation to weightlessness. The NASA/Mir Science Program combined resources of the USA and Russia to provide the first long-duration flight opportunities for the United States since the Skylab program of the early 1970s. Many of the results of these studies are still being evaluated, and in some cases data are still being collected to assess long-term readaptation to gravity after several months in weightlessness. The surge in life sciences research during this decade serves as a preamble to the opportunities to be provided by the latest addition to the Earth-orbiting structures--the International Space Station.

short duration↗
NASA NTRS1999

Fluid Physical and Transport Phenomena Studies aboard the International Space Station: Planned Experiments

This paper provides an overview of the microgravity fluid physics and transport phenomena experiments planned for the International Spare Station. NASA's Office of Life and Microgravity Science and Applications has established a world-class research program in fluid physics and transport phenomena. This program combines the vast expertise of the world research community with NASA's unique microgravity facilities with the objectives of gaining new insight into fluid phenomena by removing the confounding effect of gravity. Due to its criticality to many terrestrial and space-based processes and phenomena, fluid physics and transport phenomena play a central role in the NASA's Microgravity Program. Through widely publicized research announcement and well established peer-reviews, the program has been able to attract a number of world-class researchers and acquired a critical mass of investigations that is now adding rapidly to this field. Currently there arc a total of 106 ground-based and 20 candidate flight principal investigators conducting research in four major thrust areas in the program: complex flows, multiphase flow and phase change, interfacial phenomena, and dynamics and instabilities. The International Space Station (ISS) to be launched in 1998, provides the microgravity research community with a unprecedented opportunity to conduct long-duration microgravity experiments which can be controlled and operated from the Principal Investigators' own laboratory. Frequent planned shuttle flights to the Station will provide opportunities to conduct many more experiments than were previously possible. NASA Lewis Research Center is in the process of designing a Fluids and Combustion Facility (FCF) to be located in the Laboratory Module of the ISS that will not only accommodate multiple users but, allow a broad range of fluid physics and transport phenomena experiments to be conducted in a cost effective manner.

Singh, Bhim S.↗
NASA NTRS1978

World gravity standards

In order to use gravity anomalies in geodetic computations and geophysical interpretations, the observed gravity values from which anomalies are derived should be referred to one consistent world wide system. The International Gravity Standardization Net 1971 was adapted by the International Union of Geodesy and Geophysics at Moscow in 1971, the network was result of extensive cooperation by many organizations and individuals around the world. The network contains more than 1800 stations around the world. The data used in the adjustment included more than 25,000 gravimetry, pendulum and absolute measurements.

Uotila, U. A.↗
NASA NTRS1991

Torsional suspension system for testing space structures

A low frequency torsional suspension system for testing a space structure uses a plurality of suspension stations attached to the space structure along the length thereof in order to suspend the space structure from an overhead support. Each suspension station includes a disk pivotally mounted to the overhead support, and two cables which have upper ends connected to the disk and lower ends connected to the space structure. The two cables define a parallelogram with the center of gravity of the space structure being vertically beneath the pivot axis of the disk. The vertical distance between the points of attachment of the cables to the disk and the pivot axis of the disk is adjusted to lower the frequency of the suspension system to a level which does not interfere with frequency levels of the space structure, thereby enabling accurate measurement.

Reed, Wilmer H., III↗
NASA NTRS2006

Mechanism Development, Testing, and Lessons Learned for the Advanced Resistive Exercise Device

The Advanced Resistive Exercise Device (ARED) has been developed at NASA Johnson Space Center, for the International Space Station (ISS) program. ARED is a multi-exercise, high-load resistive exercise device, designed for long duration, human space missions. ARED will enable astronauts to effectively maintain their muscle strength and bone mass in the micro-gravity environment more effectively than any other existing devices. ARED's resistance is provided via two, 20.3 cm (8 in) diameter vacuum cylinders, which provide a nearly constant resistance source. ARED also has a means to simulate the inertia that is felt during a 1-G exercise routine via the flywheel subassembly, which is directly tied to the motion of the ARED cylinders. ARED is scheduled to fly on flight ULF 2 to the ISS and will be located in Node 1. Presently, ARED is in the middle of its qualification and acceptance test program. An extensive testing program and engineering evaluation has increased the reliability of ARED by bringing potential design issues to light before flight production. Some of those design issues, resolutions, and design details will be discussed in this paper.

Lamoreaux, Christopher D.↗
NASA NTRSDate not supplied

Two-Phase Flow in Filters and Orifices: In preparation for Measurements on ISS Packed Bed Reactor Experiment-Water Recovery Series (PBRE-WRS)

Understanding the hydrodynamics of adiabatic two-phase flows in packed bed reactors offers numerous benefits. It enables the optimization of chemical reactions rates and products, crucial for pharmaceuticals and energy production industries. Additionally, this understanding aids in designing more efficient and compact reactors, reducing space and resource requirements. Insights gained from studying such flows in microgravity contribute to advancements of space technologies and the enhancement of our capabilities for undertaking future long duration safe, and sustainable space exploration missions. The Packed Bed Reactor Experiment-Water Recovery Series (PBRE-WRS) is a flight experiment planned for operation on the Microgravity Science Glove box (MSG) facility of the International Space Station (ISS). The objective of the experiment is to validate hydrodynamic models at a range of gas and liquid flow rates. The microgravity environment allows for measurement and observation of aspects of fluid dynamics that are unique when compared to observations made in full or partial gravity environments. The experiment consists of testing two-phase flow hydrodynamics in three different filters, four (4) orifices and one check valve test articles. The experiment utilizes the hardware of the previously flown PBRE and PBRE-2 with packed beds of different packings materials and sizes. The fluid system of the PBRE-WRS consists of a nitrogen gas delivery and water delivery subsystems. The gas delivery subsystem can accommodate two ranges of gas flow rates, just as for the water delivery system. The nitrogen gas loop is open whereas the water loop is closed. Gas is separated from the water using a gas-liquid phase separator which is located in the water delivery module. Preliminary results from ground testing show the pressure drop increasing at different rates with the liquid and gas flow rates in the Brine filter. In this work, a detailed system description is presented along with a summary of results from ground performance testing of different test sections in an end-to-end preflight testing campaign.

Packed Bed Reactor Experiment↗
NASA NTRS1981

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 7: Effects of configuration modifications on the subsonic aerodynamic characteristics of the 1140 A/B orbbiter at high Reynolds numbers

Subsonic longitudinal andd laternal directional characteristics were obtained for several modified configurations of the 140 A/B orbiter (0.010 scale). These modifications, designed to extend longitudinal trim capability forward of the 65 percent fuselage length station, consisted of modified wing planform fillet and a canard. Tests were performed in the Langley Low Turbulence Pressure Tunnel at Reynolds numbers from about 4.2 million to 14.3 million based on the fuselage reference length.

Phillips, W. P.↗
NASA NTRS1985

Quantitative study on dispersion relations of TIDs observed by an HF Doppler array

A quantitative study on the dispersion relation of traveling ionospheric disturbances (TIDs) was performed by using data obtained by an HF Doppler array. Observed data at three stations are digitized continuously with a sampling period of 10 sec. A schematic illustration of a running analysis method is given. Fourier components omega's and their wave vectors k's of the TIDs are calculated from these subset data from three stations by means of the cross-spectrum analysis. Diagrams of horizontal trace velocity V sub ph versus wave period T were also obtained. From these diagrams one can see clear cutoff periods of the internal mode of the atmospheric gravity waves. A morphological classification of the mode of the omega - k and V sub ph - T obtained through one year was performed. The estimation of the horizontal velocity vectors of the thermospheric wind form their dispersion relations was performed also. A key point of the method of obtaining the vectors is to estimate the tilt, in azimuthally different omega - k diagrams, of a resonant branch ascribed to the Brunt oscillations.

Tsutsui, M.↗
NASA NTRS1999

Utilizing Advanced Vibration Isolation Technology to Enable Microgravity Science Operations

Microgravity scientific research is performed in space to determine the effects of gravity upon experiments. Until recently, experiments had to accept the environment aboard various carriers: reduced-gravity aircraft, sub-orbital payloads, Space Shuttle, and Mir. If the environment is unacceptable, then most scientists would rather not expend the resources without the assurance of true microgravity conditions. This is currently the case on the International Space Station, because the ambient acceleration environment will exceed desirable levels. For this reason, the g-LIMIT (Glovebox Integrated Microgravity Isolation Technology) system is currently being developed to provide a quiescent acceleration environment for scientific operations. This sub-rack isolation system will provide a generic interface for a variety of experiments for the Microgravity Science Glovebox. This paper describes the motivation for developing of the g-LIMIT system, presents the design concept and details some of the advanced technologies utilized in the g-LIMIT flight design.

Alhorn, Dean Carl↗
NASA NTRS1998

Modelling and Estimation of Dynamic Ocean Topography Within Global Geopotential Solutions

In this poster, we will present a report on the ongoing investigation "Improved Gravitational and Dynamic Height Models Through the use of Oceanographic Data." we have used a two year mean (1993-1994) of the Dynamic ocean Topography (DOT) field implied by the Semtner and Chervin POCM_4B model, and developed normal equations in surface spherical harmonics to degree and order 30. These normal equations, were combined with normal equations derived from TOPEX and ERS-1 altimeter data over the same time period. Combination solutions (based on satellite tracking data, altimeter data, surface gravity data and OCM data) were were developed Test solutions were obtained estimating the DOT field to 2Ox2O and 3ox3O. These solutions were tested with independent DOT values computed over 38 WOCE hydrographic sections, which contained a total of 3072 stations and represented 216000 km of travelled lines. The weighted standard deviation of the differences between the DOT obtained from the hydrographic data and and the field estimated from the joint combination solutions was computed for each of the test models, the weighted standard deviation for the baseline combination solution excluding the POCM4_B data was 9.7 cm for a DOT solution to 30x30, where introducing the POCM4_B data into the combination model reduced the standard deviation to 9.2 cm, indicating the the introduction of oceanographic information benefits the solution for the dynamic ocean topography. We will discuss the weighting schemes applied and the method of solution. Another aspect of our investigation involves testing alternate parametric representations of the dynamic height field. We looked at the alternative representations in terms of the Proudman functions (PF), and compared these to the use of spherical harmonics (SH) to represent the dynamic ocean topography, using once again the 1993 and 1994 output of the POCM4_B OCM as the reference model. A significant advantage of PF's over SH's is that the former require no "fill-in" values over areas where the DOT is undefined. We show that the PF and SH results using equal number of parameters agree quite well in overall content. In addition, PFs appear better suited for representation of high frequency signals close to the signal boundary. The development of the PF solutions for the DOT will be described and the statistics of the comparisons will be presented.

Lemoine, Frank G.↗
NASA NTRS2002

Restraining Loose Equipment Aboard the International Space Station: The Payload Equipment Restraint System

As the International Space Station (ISS) grows, so do the supplies and equipment needed to support its daily operations. Each day many items must be unstowed and relocated to various worksites so they are readily available to the crew. Due to the lack of gravity, these items may become loose and float away if not restrained. The Payload Equipment Restraint System was developed to meet the new and unique challenge of restrain no loose equipment aboard the ISS.

Smith, Kenneth A.↗
NASA NTRS2004

The effect of simulated microgravity on bacteria from the Mir space station

The effects of simulated microgravity on two bacterial isolates, Sphingobacterium thalpophilium and Ralstonia pickettii (formerly Burkholderia pickettii), originally recovered from water systems aboard the Mir space station were examined. These bacteria were inoculated into water, high and low concentrations of nutrient broth and subjected to simulated microgravity conditions. S. thalpophilium (which was motile and had flagella) showed no significant differences between simulated microgravity and the normal gravity control regardless of the method of enumeration and medium. In contrast, for R. pickettii (that was non-motile and lacked flagella), there were significantly higher numbers in high nutrient broth under simulated microgravity compared to normal gravity. Conversely, when R. pikkettii was inoculated into water (i.e., starvation conditions) significantly lower numbers were found under simulated microgravity compared to normal gravity. Responses to microgravity depended on the strain used (e.g., the motile strain exhibited no response to microgravity, while the non-motile strain did), the method of enumeration, and the nutrient concentration of the medium. Under oligotrophic conditions, non-motile cells may remain in geostationary orbit and deplete nutrients in their vicinity, while in high nutrient medium, resources surrounding the cell may be sufficient so that high growth is observed until nutrients becoming limiting.

Non-NASA Center↗
NASA NTRS2004

The NASA Materials Science Research Program: It's New Strategic Goals and Opportunities

In the past year, the NASA s Office of Biological and Physical Research (OBPR) has formulated a long term plan to perform strategical and fundamental research bringing together physics, chemistry, biology, and engineering to solve problems needed for current and future agency mission goals. Materials Science is one of basic disciplines within the Enterprise s Division of Physical Sciences Research. The Materials Science Program participates to utilize effective use of International Space Station (ISS) and various world class ground laboratory facilities to solve new scientific and technology questions and transfer these results for public and agency benefits. The program has recently targeted new investigative research in strategic areas necessary to expand NASA knowledge base for exploration of the universe and some of these experiments will need access to the microgravity of space. The program is implementing a wide variety of traditional ground and flight based research related types of fundamental science related to materials crystallization, fundamental processing, and properties characterization in order to obtain basic understanding of various phenomena effects and relationships to the structures, processing, and properties of materials. , In addition new initiatives in radiation protection, materials for propulsion and In-space fabrication and repair focus on research helping the agency solve problems needed for future transportation into the solar system. A summary of the types and sources for this research is presented including those experiments planned for a low gravity environment. Areas to help expand the science basis for NASA future missions are described. An overview of the program is given including the scope of the current and future NASA Research Announcements with emphasis on new materials science initiatives. A description of the planned flight experiments to be conducted on the International Space Station program along with the planned facility class Materials Science Research Rack (MSRR) and Microgravity Glovebox (MSG) type investigations. Some initial results from the first three materials experiments are given.

Schlagheck, Ronald A.↗
NASA NTRS1983

The development of a Space Shuttle General Purpose Work Station (GPWS)

The GPWS being developed for the Life Sciences Laboratory to be flown on the fourth Spacelab mission in late 1985 is characterized, and results from Phase I and Phase II tests are reported. The GPWS is designed to provide biological protection for both experiment and operator, a clean-room environment, control of liquids at zero gravity, protection against Spacelab-cabin contamination by chemical vapors, and work space with lights and other accommodations for one or two users in the zero-gravity neutral-body position. The flight hardware subsystems are examined and illustrated; the approach taken to evaluate human factors, performance, contaminant control, and user accommodation is explained; the design-verification unit for ground testing is described; and the improvements introduced in constructing the flight version are indicated.

Wagner, P. A.↗