Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain texture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Creep study of mechanisms involved in low-temperature superplasticity of UFG Ti-6Al-4V processed by SPD

The deformation kinetics of ultrafine-grained Ti-6Al-4V with mean (sub)grain size about 150 nm (produced by isothermal multiaxial forging) and superplastic properties at the relatively low temperature of 873 K was investigated in compression and tension over a large range of strain rates from 10{sup −7} to 10{sup −2} s{sup −1}. Electron microscopic observations showed that the grains coarsen during deformation towards the quasi-stationary spacing w{sub qs} of strain induced boundaries. In spite of the grain coarsening the grains were generally smaller than w{sub qs} allowing high-angle boundaries to dominate the quasi-stationary strength. Texture measurements indicate that dislocation glide plays a large role in deformation. Glide in this alloy is significantly influenced by solid solution strengthening leading to a stress sensitivity of strain rate of n = 3. The present ultrafine-grained Ti alloy displays a stress sensitivity exponent n = 2 over an extended stress range where its superplastic behavior is optimal. While the deformation kinetics of present ultrafine-grained Ti alloy can be roughly explained by the traditional formula for superplastic flow, the significant discrepancy to the measured values suggests that solid solution strengthening must be taken into account to get a complete insight. - Highlights: • The UFG Ti-6Al-4V alloy behaves superplastically at low temperature of 873 K. • Grain coarsening at low stresses limits superplasticity of UFG Ti alloy. • Solute strengthening plays an important role in low-temperature superplasticity. • Acceleration of creep in UFG Ti alloy is caused by processes related to hab.

36 MATERIALS SCIENCE↗

Characterization of microstructure and texture across dissimilar super duplex/austenitic stainless steel weldment joint by austenitic filler metal

The evolution of microstructure and texture across an as-welded dissimilar UNS S32750 super duplex/UNS S30403 austenitic stainless steel joint welded by UNS S30986 (AWS A5.9 ER309LMo) austenitic stainless steel filler metal using gas tungsten arc welding process was evaluated by optical micrography and EBSD techniques. Due to their fabrication through rolling process, both parent metals had texture components resulted from deformation and recrystallization. The weld metal showed the highest amount of residual strain and had large austenite grain colonies of similar orientations with little amounts of skeletal ferrite, both oriented preferentially in the < 001 > direction with cub-on-cube orientation relationship. While the super duplex stainless steel's heat affected zone contained higher ferrite than its parent metal, an excessive grain growth was observed at the austenitic stainless steel's counterpart. At both heat affected zones, austenite underwent some recrystallization and formed twin boundaries which led to an increase in the fraction of high angle boundaries as compared with the respective base metals. These regions showed the least amount of residual strain and highest amount of recrystallized austenite grains. Due to the static recrystallization, the fraction of low degree of fit (Σ) coincident site lattice boundaries, especially Σ3 boundaries, was increased in the austenitic stainless steel heat affected zone, while the formation of subgrains in the ferrite phase increased the content of < 5° low angle boundaries at that of the super duplex stainless steel. - Graphical abstract: Display Omitted - Highlights: • Extensive grain growth in the HAZ of austenitic stainless steel was observed. • Intensification of < 100 > orientated grains was observed adjacent to both fusion lines. • Annealing twins with Σ3 CSL boundaries were formed in the austenite of both HAZ. • Cub-on-cube OR was observed between austenite and ferrite in the weld metal. • Weld metal had the lowest texture intensity and ratio of low angle and CSL boundaries.

36 MATERIALS SCIENCE↗

An Amoeboid Olivine Aggregate in LEW 85300

Amoeboid Olivine aggregates (AOAs) are irregularly shaped objects commonly observed in carbonaceous chondrites. Because they are composed of fine-grained olivine and Ca-Al-rich minerals, they are sensitive indicators for nebular process and parent body alteration of their parent bodies. Recently an AOA was found in a carbonaceous clast in polymict eucrite LEW 85300. The bulk major element composition of the clast matrix in LEW 85300 suggests a relation to CM, CO and CV chondrites, whereas bulk clast trace and major element compositions do not match any carbonaceous chondrite, suggesting they have a unique origin. Here we characterize the mineralogy of AOA in LEW 85300 and discuss the origin of the carbonaceous clasts. Results and Discussion: The AOA is located in an impact melt vein. Half of the aggregate shows recrystallization textures (euhedral pyroxene and molten metal/FeS) due to impact melting, but the remaining part preserves the original texture. The AOA is composed of olivine, FeS and Mg,Al-phyllosilicate. Individual olivine grains measure 1-8 microns, with Fe-rich rims, probably due to impact heating. Olivines in the AOA are highly forsteritic (Fo95-99), indicating that the AOA escaped thermal metamorphism [4]. Although no LIME (Low-Fe, Mn-Enriched) olivine is observed, forsterite composition and the coexistence of Mg,Al-phyllosilicate suggest that the AOA is similar to those in the Bali-type oxidized CV (CVoxB) and CR chondrites. However, it should be noted that fayalitic olivine, which commonly occurs in CVoxB AOA, is not observed in this AOA. Also, the smaller grain size (<8 microns) of olivine suggests they may be related to CM or CO chondrites. Therefore, we cannot exclude the possibility that the AOA originated from a unique carbonaceous chondrite.

Komatsu, M. D.↗

Effect of strain on evolution of dynamic recrystallization in Nb-1 wt%Zr-0.1 wt%C alloy at 1500 and 1600 °C

Uniaxial compression tests were carried out on Nb-1 wt%Zr-0.1 wt%C alloy at temperature of 1500 and 1600 °C and strain rate of 0.1 s{sup −1} to study the evolution of dynamic recrystallization with strain. Electron back scatter diffraction was used to quantify the microstructural evolution. Nb-1Zr-0.1C alloy showed a necklace structure at a strain of 0.9 when deformed at 1500 °C and at strain of 0.6 when deformed at 1600 °C, both at strain rate of 0.1 s{sup −1}. This suggested the occurrence of dynamic recrystallization. At 1500 °C and strain of 0.9 the local average misorientation and the grain orientation spread was low confirming the presence of dynamic recrystallization at this deformation condition. At both 1500 and 1600 °C and all measured strains the recrystallized grains had a strong fiber component of <001>. - Highlights: • Necklace formation of dynamically recrystallized grains occurred at strain of 0.6 and 0.9 for 1500 and 1600 °C, respectively. • Equiaxed microstructures were seen with increase in strain for both 1500 and 1600 °C. • At large strains the predominant recrystallized texture evolved to <001> pole.

36 MATERIALS SCIENCE↗

Enhanced strength and electrical conductivity of ultrafine-grained Al-Mg-Si alloy processed by hydrostatic extrusion

Highlights: • Al-Mg-Si alloy was subjected to hydrostatic extrusion combined with aging treatment. • UFG Al-Mg-Si alloy with UTS of 332 MPa and conductivity of 58% IACS was obtained. • Precipitation process depended on applied strains and crystallographic texture. • Strengthening effect was achieved by UFG structure and needle-like β″ precipitates. • Precipitation of β″ and spherical β′/β particles at GB provided high conductivity. - Abstract: The effect of hydrostatic extrusion combined with an artificial aging on microstructure, mechanical and electrical properties of 6101 Al-Mg-Si alloy was investigated. It has been shown that such thermo-mechanical treatment is an effective method for producing of long wires with an ultrafine-grained microstructure (grain size of 300–400 nm) and enhanced ultimate tensile strength (> 330 MPa) and electrical conductivity (up to 58% IACS). The mechanical behavior of 6101 Al-Mg-Si alloy depended strongly on applied strains by hydrostatic extrusion and crystallographic texture. Higher accumulative strain accelerated the precipitation kinetics but decreased the age hardening response. The double fiber <100> and <111> texture was observed for hydrostatically extruded samples. The <001> grains with homogenously distributed needle-like β″ precipitates provided precipitation strengthening of material while <111> grains resulted in more efficient grain boundary strengthening. Quantitative microstructure characterization allowed adjusting physical model to estimate the electrical conductivity and compare it with experimental data. The high conductivity was provided mainly by decomposition of solid solution due to precipitation of needle-like β″ precipitates in the grain interior and spherical β′ or β particles located at grain boundaries.

36 MATERIALS SCIENCE↗

An automated procedure built on MTEX for reconstructing deformation twin hierarchies from electron backscattered diffraction datasets of heavily twinned microstructures

Here we present a set of algorithms built on the MTEX and MATLAB graph toolboxes for automatic reconstruction of deformation twin hierarchies from Electron Backscatter Diffraction (EBSD) datasets with a focus on developing methods for heavily twinned microstructures (twin fractions >0.5). The algorithms address key issues arising at large strains, mainly: missing twin relationships, grouping of heavily deformed grain fragments into families of similar orientation originating from a single initial grain, identification of parent fragments for large twin volume fractions, and classification of families having twin relationships with multiple families. To facilitate the development of these algorithms, large-grained ultra-high purity α-Ti deformed in compression along two directions is investigated. Graphs are utilized to handle non-local geometric merging and to represent relationships throughout the reconstruction process. When determining if a grain fragment is from the undeformed microstructure, the combined metrics of the fragment's orientation volume fraction in the initial texture and the directed graph centrality measure of out-closeness (the number of nodes reached in a graph from a given node) are essential. To address automation in reconstructing the sequence of twinning and relating fragments originating from a single grain in the initial microstructure, the twin family tree is formulated as a minimum spanning tree emanating from the initial grain family. A scheme constructing the distances associated with twin relationship comprising the spanning tree is developed, and a novel quasi-directional Prim spanning tree algorithm is used to determine the twin family tree. The procedure is demonstrated to significantly improve the level of automation in reconstructing twin hierarchies in heavily twinned microstructure compared to other methodologies in literature. The procedure can readily be applied to analyses of twinning in metals, as well as provide an approach for routinely extracting twin statistics at larger deformation levels than previously possible. Significantly, the procedure is demonstrated to be capable of identifying third generation twinning in α-Ti microstructures.

36 MATERIALS SCIENCE↗

Chemistry, Mineralogy, and Grain Properties at Namib and High Dunes, Bagnold Dune Field, Gale Crater, Mars: A Synthesis of Curiosity Rover Observations: Bagnold Dune Sands Composition

The Mars Science Laboratory Curiosity rover performed coordinated measurements to examine the textures and compositions of aeolian sands in the active Bagnold dune field. The Bagnold sands are rounded to subrounded, very fine- to medium- sized (~45-500 µm) with ≥6 distinct grain colors. In contrast to sands examined by Curiosity in a dust-covered, inactive bedform called Rocknest and soils at other landing sites, Bagnold sands are darker, less red, better sorted, have fewer silt-sized or smaller grains, and show no evidence for cohesion. Nonetheless, Bagnold mineralogy and Rocknest mineralogy are similar with plagioclase, olivine, and pyroxenes in similar proportions comprising >90% of crystalline phases, along with a substantial amorphous component (35% ± 15%). Yet, Bagnold and Rocknest bulk chemistry differ. Bagnold sands are Si-enriched relative to other soils at Gale crater, and H 2 O, S, and Cl are lower relative to all previously measured martian soils and most Gale crater rocks. Mg, Ni, Fe, and Mn are enriched in the coarse-sieved fraction of Bagnold sands, corroborated by VNIR spectra that suggest enrichment of olivine. Together, patterns in major element chemistry and volatile release data indicate two distinctive volatile reservoirs in martian soils: (1) amorphous components in the sand-sized fraction (represented by Bagnold) that are Si-enriched, hydroxylated alteration products and/or impact or volcanic glasses; and (2) amorphous components in the fine fraction (<40 µm; represented by Rocknest and other bright soils) that are Fe-, S-, and Cl-enriched with low Si and adsorbed and structural H 2 O.

58 GEOSCIENCES↗

Ionic conductivity and thermal stability of magnetron-sputtered nanocrystalline yttria-stabilized zirconia

Thermally stable, stoichiometric, cubic yttria-stabilized zirconia (YSZ) thin-film electrolytes have been synthesized by reactive pulsed dc magnetron sputtering from a Zr-Y (80/20 at. %) alloy target. Films deposited at floating potential had a <111> texture. Single-line profile analysis of the 111 x-ray diffraction peak yielded a grain size of approx20 nm and a microstrain of approx2% regardless of deposition temperature. Films deposited at 400 deg. C and selected bias voltages in the range from -70 to -200 V showed a reduced grain size for higher bias voltages, yielding a grain size of approx6 nm and a microstrain of approx2.5% at bias voltages of -175 and -200 V with additional incorporation of argon. The films were thermally stable; very limited grain coarsening was observed up to an annealing temperature of 800 deg. C. Temperature-dependent impedance spectroscopy analysis of the YSZ films with Ag electrodes showed that the in-plane ionic conductivity was within one order of magnitude higher in films deposited with substrate bias corresponding to a decrease in grain size compared to films deposited at floating potential. This suggests that there is a significant contribution to the ionic conductivity from grain boundaries. The activation energy for oxygen ion migration was determined to be between 1.14 and 1.30 eV.

36 MATERIALS SCIENCE↗

Microstructural and Textural Evolutions during β → α/ω Transformation in Biomedical Ti-15Mo Alloy and Its Effects on Mechanical Performance

This study investigated the precipitation behaviors and mechanical performance of Ti-15Mo alloy subjected to different treatment conditions. The microstructures were analyzed via scanning electron microscopy and transmission electron microscopy. The tensile properties and resultant fracture surfaces were investigated to determine the relationship between the phase transformation and mechanical performance. The Ti-15Mo alloy had a notable elongation due to no observable precipitation during solution treatment plus quenching (STQ). A high ultimate tensile strength (UTS) was obtained with a considerable amount of ω precipitates transformed during air cooling after solution treatment (ST). The coarse precipitates and additional precipitation free zones in the Ti-15Mo alloy treated with furnace cooling (FC) after ST induced a decrease in UTS. Furthermore, the absence of a continuous grain boundary α phase resulted in a lower strength in the specimen annealed at 600 °C after hot rolling. The alloy iso-aged after STQ exhibited good tensile properties with a UTS of 920 MPa and an elongation of 15%. The texture and variant relationship of the precipitates was analyzed with x-ray diffraction and electron backscatter diffraction. The common variants of the β matrix influenced the nucleation of precipitates in the Ti-15Mo alloy annealed after hot rolling, and the precipitates showed an obvious {01-10}α main texture. The variant selection of α precipitates at the grain boundary was caused by the two adjacent β grains in the alloy treated by FC after ST.

36 MATERIALS SCIENCE↗

Effect of Rolling Deformation on the Microstructure and Mechanical Properties of an Extruded Mg-Zn-Ca Alloy

The microstructure and mechanical properties of an as-extruded Mg-4.5Zn-1.1Ca (wt.%) alloy subjected to unidirectional rolling and cross-rolling were compared in the present study. The results indicated that rolling deformation refined the microstructure, dispersed second phases and modified the texture, which resulted in an improvement in the mechanical properties of the as-rolled alloys compared with those of the as-extruded alloy. The yield strength of the Mg-4.5Zn-1.1Ca (wt.%) alloy increased from 173 to 297 MPa after unidirectional rolling. The initial fragmented Ca{sub 2}Mg{sub 6}Zn{sub 3} phases were further refined after rolling deformation, which clearly restricted the grain growth and gave rise to a fine microstructure. It was also found that rolling deformation intensified the basal texture in comparison with the as-extruded alloy, which was related to particle pinning.

36 MATERIALS SCIENCE↗

The relationships between residual stress relaxation and texture development in AZ31 Mg alloys via the vibratory stress relief technique

A systematic study of residual stress relaxation and the texture evolution of cold-rolled AZ31 Mg alloys using the vibratory stress relief technique with a simple cantilever beam vibration system was performed using a high-resolution X-ray diffractometer and a portable X-ray residual stress analyzer. The effects of vibrational stress excitation on the surface residual stress distribution and on the texture of pole figures (0002) occurring during the vibratory stress relief were examined. Compared with the effects corresponding to the same alloy under non-vibration condition, it can be observed that the uniform surface residual stress distribution and relaxation of the compressive residual stress in the stress concentration zone were observed rather than all of the residual stresses being eliminated. Furthermore, with an increase in the vibrational aging time, the compressive residual stress, texture density, and (0002) preferred orientation increased first and then decreased. It should be underlined that the vibratory stress relief process for the vibrational aging time of more than 10 min is able to weaken the strong basal textures of AZ31 Mg alloys, which is valuable for enhancement of their formability and is responsible for an almost perfect 3D-Debye–Scherrer ring. - Highlights: • 3D-Debye ring about VSR technique is not discussed in the existing literature. • A newly developed VSR method is suitable for small or thin workpieces. • The cosα method accurately and effectively determines the residual stresses. • The VSR technique is valuable for enhancement of their formability. • The texture and preferred orientation change with the vibrational aging time.

36 MATERIALS SCIENCE↗

Survey of basic XRD applications.

This 1/2 day workshop will survey various applications of XRD analysis, including in-situ analyses and neutron diffraction. The analyses will include phase ID, crystallite size and microstrain, preferred orientation and texture, lattice parameters and solid solutions, and residual stress. Brief overviews of high-temperature in-situ analysis, neutron diffraction and synchrotron studies will be included.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of the accuracy of modeling the orientation distribution function of polycrystalline materials from individual orientations

The accuracy of reconstructing the orientation distribution function of grains in polycrystalline materials by the kernel method from a set of individual orientations has been studied. In particular, the influence of choosing the smoothing kernel in the kernel method and the influence of the dependence on the resulting distribution are taken into account. The rotations obeying the normal distribution on the group SO(3) and obtained by the statistical test method are used as an orientation set. Some aspects of electron backscattering diffraction measurements are considered. This problem is urgent in view of the expanding potential of the experimental study of the texture of polycrystalline materials, especially for electron microscopy, which makes it possible to measure the orientations of individual grains.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Ultrafine Mineralogy of a Molten Interplanetary Dust Particle as an Example of the Quench Regime of Atmospheric Entry Heating

Melting and degassing of interplanetary dust particle L2005B22 at approx. 1200 C was due to flash heating during atmospheric entry. Preservation of the porous particle texture supports rapid quenching from the peak heating temperature whereby olivine and pyroxene nanocrystals (3 nm-26 nm) show partial devitrification of the quenched melt at T approx. = 450 C - 740 C. The implied ultrahigh cooling rates are calculated at approx. 105 C/h-106 C/h, which is consistent with quench rates inferred from the temperature-time profiles based on atmospheric entry heating models. A vesicular rim on a nonstoichiometric relic forsterite grain in this particle represents either evaporative magnesium loss during flash heating or thermally annealed ion implantation texture.

Rietmeijer, Frans J. M.↗

Anisotropic SmCo{sub 5} nanoflakes by surfactant-assisted high energy ball milling

Crystallographically anisotropic SmCo{sub 5} nanoflakes were fabricated directly by one-step surfactant-assisted high energy ball milling (HEBM) of Sm{sub 17}Co{sub 83} ingot powders for 5 h in heptane and oleic acid (OA) without preprocessing or further annealing. The SmCo{sub 5} nanoflakes have a strong [001] out-of-plane texture. The thickness of nanoflakes is in the range of 8-80 nm while their length is 0.5-8 {mu}m. The surfactant OA plays an important role in the formation of SmCo{sub 5} nanoflakes. HEBM of SmCo{sub 5} ingots in heptane without OA resulted in the formation of magnetically isotropic more or less equiaxed SmCo{sub 5} particles with a size of 2-30 {mu}m. Closely packed 'kebablike' SmCo{sub 5} nanoflakes were formed by HEBM in heptane with 15 wt % OA. HEBM in 150 wt % OA led to well-separated nanoflakes instead of the closely packed kebablike nanostructure. This resulted in the enhanced [001] out-of-plane texture. In-plane transmission electron microscope examination showed that the SmCo{sub 5} nanoflakes were composed of grains with sizes in the range of 4-8 nm. Coercivities of about 18.0 kOe were obtained for the anisotropic SmCo{sub 5} nanoflakes.

36 MATERIALS SCIENCE↗

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗

Asymmetric cross rolling (ACR): A novel technique for enhancement of Goss/Brass texture ratio in Al-Cu-Mg alloy

Highlights: • The main components of the ACR were Goss, Rotated Goss, Goss-Brass, and α-fiber. • The ACR process was obviously impactful to enhance the Goss/Brass texture ratio. • The Goss/Brass texture ratio increased to 1.51 after 30% ACR process. • During 30% rolling, the DRX occurred and the intensity of Goss and Cube increased. - Abstract: The present work focused on the effect of asymmetric cross rolling (ACR) process as a novel technique on microstructure and texture evolution of Al-Cu-Mg alloys. The microstructural observation and bulk texture from RD–TD plane of the initial and deformed samples were characterized by optical microscopy (OM) and X-ray diffraction (XRD). It was found that the deformed Al-Cu-Mg alloy consisted of strong Goss, Rotated Goss, Goss-Brass, and α-fiber textures. Usually, straight rolling leads to a significant strengthening of the Brass component with increasing strain in the Al-Cu-Mg alloy, but for asymmetrically cross rolled samples, the Goss orientation was stable after 40% deformation. Results showed that the ACR process was effective to intensify (up to 1.51 after 30% thickness reduction) the low Goss/Brass texture ratio often existing in the rolled Al-Cu-Mg alloy. During 30% ACR, the dynamic recrystallization (DRX) occurred, which led to increasing the intensity of Goss and Cube components and the fraction of extra high angle grain boundaries (EHAGBs).

36 MATERIALS SCIENCE↗

Influence of Rotation Rate on Microstructure and Comprehensive Performance of FSWed Mg Alloy

Die-casting AZ31 Mg alloys were successfully friction stir welded at a constant welding speed and different rotation rates. More uniform and fine grains were obtained at the rotation rate of 1400 rpm due to more suitable temperature for dynamic recrystallization in this welding condition. In addition, the intensity of (0001) texture in stir zone increased with the increasing rotation rate. The results of mechanical property test indicated joint with rotation rate of 1400 rpm had better tensile property, which was associated with fine grains, uniform transition in the interface between thermo-mechanically affected zone and stir zone as well as more favorable Schmidt factor for basal slip and twinning. The corrosion resistance of joints increased with the increasing rotation rate, which is significantly related to the (0001) texture with basal plane parallel to the corroded surfaces.

36 MATERIALS SCIENCE↗