Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flat”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Large-area high-efficiency ion-implanted cells and flat-plate modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. Module efficiency of 14 percent (25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1987

Endwall heat transfer in the junction region of a circular cylinder normal to a flat plate at 30 and 60 degrees from stagnation point of the cylinder

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

Nagamatsu, H. T.↗
NASA NTRS1987

Performance improvements in silicon flat-plate cells and modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells developed in this work are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. A comparison of float zone and Czochralski silicon is made. Module efficiency of over 15 percent (at 25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1985

Electricity from photovoltaic solar cells. Flat-Plate Solar Array Project of the US Department of Energy's National Photovoltaics Program: 10 years of progress

The objectives were to develop the flat-plate photovoltaic (PV) array technologies required for large-scale terrestrial use late in the 1980s and in the 1990s; advance crystalline silicon PV technologies; develop the technologies required to convert thin-film PV research results into viable module and array technology; and to stimulate transfer of knowledge of advanced PV materials, solar cells, modules, and arrays to the PV community. Progress reached on attaining these goals, along with future recommendations are discussed.

Christensen, Elmer↗
NASA NTRS1987

CCD photometry of globular cluster core structure. I - NGC 6388, NGC 6624, and M15: One flat core and two cusps

The first results of a major survey of globular cluster core structure are reported. Surface brightness profiles for three clusters are presented: one with a normal flat core profile (NGC 6388), and two with central cusps (NGC 6624 and M15). The profiles are fitted with both seeing-convolved King models and seeing-convolved power laws. A King model provides a reasonable fit to the entire profile of NGC 6388, but there are no acceptable King profiles for NGC 6624 and M15. For these two clusters, a seeing-convolved power law provides a good fit to the inner part of the profile, while a King model gives a good fit to the outer part of the profile. The interpretation of the measured power-law slopes of the central surface brightness cusps of NGC 6624 and M15 are discussed in terms of models for core collapse in a multicomponent cluster.

Lugger, Phyllis M.↗
NASA NTRS1987

Prediction of transition on a flat plate under the influence of free-stream turbulence using low-Reynolds-number two-equation turbulence models

The prediction characteristics and capabilities of two popular two-equation low-Reynolds-number turbulence models (Jones, Launder 1972; Lam, Bremhorst 1981) have been evaluated with respect to the prediction of transition of a flat plate under the influence of free-stream turbulence. The sensitivity of the predictions to free-stream turbulence intensity, initial starting location of the calculation, and the assumed initial starting profiles for k and epsilon has been determined and presented. Although both models predict the correct qualitative characteristics of transition, they also exhibit significant quantitative deficiencies with regard to both the predicted location and the length of transition. A modification to the production term in the turbulent kinetic energy equation is proposed which is based on a simple stability criterion and correlated to the free-stream turbulence level. The modification becomes inactive in the fully turbulent regime, but is shown to improve both the qualitative and quantitative characteristics of the transition predictions.

Schmidt, Rodney C.↗
NASA NTRS1987

The economic payoff for a state-of-the-art high-efficiency flat-plate crystalline silicon solar cell technology

In 1986 during the flat-plate solar array project, silicon solar cells 4.0 sq cm in area were fabricated at the Jet Propulsion Laboratory (JPL) with a conversion efficiency of 20.1 percent (AM1.5-global). Sixteen cells were processed with efficiencies measuring 19.5 percent (AM1.5 global) or better. These cells were produced using refined versions of conventional processing methods, aside from certain advanced techniques that bring about a significant reduction in a major mechanism (surface recombination) that limits cell efficiency. Wacker Siltronic p-type float-zone 0.18-ohm-cm wafers were used. Conversion efficiencies in this range have previously been reported by other researchers, but generally on much smaller (0.5 vs. 4.0 cm) devices which have undergone sophisticated and costly processing steps. An economic analysis is presented of the potential payoffs for this approach, using the Solar Array Manufacturing Industry Costing Standards (SAMICS) methodology. The process sequence used and the assumptions made for capturing the economies of scale are presented.

Bickler, Donald B.↗
NASA NTRS1987

Post-flare coronal arches observed with the SMM/XRP flat crystal spectrometer

Postflare coronal arch observations made with the SMM Flat Crystal Spectrometer on January 20-23, 1985 are discussed. Results suggest that the arch revival following the dynamic flare of 23:50 UT on January 1 was of the type noted on November 6-8 and June 4, 1980 by the SMM Hard X-ray Imaging Spectrometer (HXIS). Activity different from that of the HXIS observations was found starting at about 23 UT on January 22, with no trigger of the revival being identified, and with the activity being restricted to the coronal regions (without any related disturbance in the chromosphere). The development of the arch enhancement in the corona was shown to be slower than is expected for a flare-associated revival.

Hick, Paul↗
NASA NTRS1988

Effect of large amplitude pitching motions on the unsteady aerodynamic characteristics of flat-plate wings

Large-amplitude unsteady motion effects on the aerodynamic force and stability characteristics of flat-plate wings were investigated in a wind tunnel for the cases of two delta wings with respective leading edge sweeps of 70 and 45 deg, and a rectangular wing whose aspect ratio was equal to that of the 70-deg delta wing. Attention was given to the effects of reduced frequency and mean angle of attack. It is found that lags in vortex burst location and separation/reattachment of flow on the upper surface of the wing produced large overshoots and hysteresis loops in normal force and pitching moment coefficients that were a strong function of mean oscillation angle and reduced frequency.

Brandon, Jay M.↗
NASA NTRS1988

Design of high-Reynolds-number flat-plate experiments in the NTF

The design of an experiment to measure skin friction and turbulent boundary layer characteristics at Reynolds numbers exceeding 1 x 10 to the 9th is described. The experiment will be conducted in a zero-pressure-gradient flow on a flat plate in the National Transonic Facility (NTF). The development of computational codes to analyze the aerodynamic loads and the blockage is documented. Novel instrumentation techniques and models, designed to operate in cryogenic environments, are presented. Special problems associated with aerodynamic loads, surface finish, and hot-wire anemometers are discussed.

Saric, William S.↗
NASA NTRS1988

Rarefied flow past a flat plate at incidence

Results of a numerical study using the direct simulation Monte Carlo (DSMC) method are presented for the transitional flow about a flat plate at 40 deg incidence. The plate has zero thickness and a length of 1.0 m. The flow conditions simulated are those experienced by the Shuttle Orbiter during reentry at 7.5 km/s. The range of freestream conditions are such that the freestream Knudsen number values are between 0.02 and 8.4, i.e., conditions that encompass most of the transitional flow regime. The DSMC simulations show that transitional effects are evident when compared with free molecule results for all cases considered. The calculated results demonstrate clearly the necessity of having a means of identifying the effects of transitional flow when making aerodynamic flight measurements as are currently being made with the Space Shuttle Orbiter vehicles. Previous flight data analyses have relied exclusively on adjustments in the gas-surface interaction models without accounting for the transitional effect which can be comparable in magnitude. The present calculations show that the transitional effect at 175 km would increase the Space Shuttle Orbiter lift-drag ratio by 90 percent over the free molecule value.

Dogra, Virendra K.↗
NASA NTRS1989

Nonprincipal plane scattering of flat plates and pattern control of horn antennas

Using the geometrical theory of diffraction, the traditional method of high frequency scattering analysis, the prediction of the radar cross section of a perfectly conducting, flat, rectangular plate is limited to principal planes. Part A of this report predicts the radar cross section in nonprincipal planes using the method of equivalent currents. This technique is based on an asymptotic end-point reduction of the surface radiation integrals for an infinite wedge and enables nonprincipal plane prediction. The predicted radar cross sections for both horizontal and vertical polarizations are compared to moment method results and experimental data from Arizona State University's anechoic chamber. In part B, a variational calculus approach to the pattern control of the horn antenna is outlined. The approach starts with the optimization of the aperture field distribution so that the control of the radiation pattern in a range of directions can be realized. A control functional is thus formulated. Next, a spectral analysis method is introduced to solve for the eigenfunctions from the extremal condition of the formulated functional. Solutions to the optimized aperture field distribution are then obtained.

Balanis, Constantine A.↗
NASA NTRS1988

Flat-plate solar array project: Government and industry responding to national needs

This document recounts the accomplishments of the 11-year Flat-Plate Solar Array Project, which is recognized as one of the most successful and comprehensive technology-transfer efforts ever achieved through government-sponsored research and development. Few Federal research projects can claim the degree of industry involvement that was a fundamental aspect of the FSA Project. This philosophy in turn led to an extraordinary transfer of technology to the private sector, and assured that a maximum amount of the taxpayers' dollars were devoted to research of primary importance to the technology's commercialization.

Adcock, J. Patrick↗
NASA NTRS1989

Asymptotic behavior of a flat plate wake

An experimental study has been conducted to investigate the far-field, self-similar properties of a flat plate wake. A plane turbulent wake was generated at the trailing edge of a smooth splitter plate separating two legs of a Mixing Layer Wind Tunnel, with both initial boundary layers tripped. For the present study, both legs were operated at a free-steam velocity in the test section of 15 m/s, giving a Reynolds number based on wake momentum thickness of about 1750. Single profile measurements were obtained at five streamwise locations using a Pitot probe for the mean velocity measurements and a single cross-wire probe for the turbulence data, which included statistics up to third order. The mean flow data indicated a self-similar behavior beyond a streamwise distance equivalent to about 350 wake momentum thicknesses. However, the turbulence data show better collapse beyond a distance equivalent to about 500 momentum thicknesses, with all the measured peak Reynolds stresses achieving constant, asymptotic levels. The asymptotic mean flow behavior and peak primary stress levels agree well with theoretical predictions based on a constant eddy viscosity model. The present data also agree reasonably well with previous measurements, of which only one set extends into the self-similar region. Detailed comparisons with previous data are presented and discussed in this report.

Weygandt, James H.↗
NASA NTRS1989

Time domain numerical calculations of unsteady vortical flows about a flat plate airfoil

A time domain numerical scheme is developed to solve for the unsteady flow about a flat plate airfoil due to imposed upstream, small amplitude, transverse velocity perturbations. The governing equation for the resulting unsteady potential is a homogeneous, constant coefficient, convective wave equation. Accurate solution of the problem requires the development of approximate boundary conditions which correctly model the physics of the unsteady flow in the far field. A uniformly valid far field boundary condition is developed, and numerical results are presented using this condition. The stability of the scheme is discussed, and the stability restriction for the scheme is established as a function of the Mach number. Finally, comparisons are made with the frequency domain calculation by Scott and Atassi, and the relative strengths and weaknesses of each approach are assessed.

Hariharan, S. I.↗
NASA NTRS1989

Relaminarization of turbulent flow on a flat plate by localized surface heating

Relaminarization of a turbulent boundary layer in air on a flat plate is demonstrated experimentally using localized surface heating. Localized heating is achieved by electrically heating a wire embedded in a thermally insulated substrate (Space Shuttle Tile) on the surface. The stability of the flow downstream of the applied control point increases with decreasing stream temperature in the flow direction. The mean and perturbation velocity profiles without control show that the flow is turbulent. With control, these profiles sequentially change from intermittently turbulent to a fully laminar state. In the relaminarization stage, the turbulent energy is dissipated by molecular transport due to viscous and conductivity mechanisms. The new profile adjusts to a lower Reynolds number based on the momentum thickness than that of the previous turbulent state.

Maestrello, Lucio↗
NASA NTRS1989

A useful approximation for the flat surface impulse response

The flat surface impulse response (FSIR) is a very useful quantity in computing the mean return power for near-nadir-oriented short-pulse radar altimeters. However, for very small antenna beamwidths and relatively large pointing angles, previous analytical descriptions become very difficult to compute accurately. An asymptotic approximation is developed to overcome these computational problems. Since accuracy is of key importance, a condition is developed under which this solution is within 2 percent of the exact answer. The asymptotic solution is shown to be in functional agreement with a conventional clutter power result and gives a 1.25-dB correction to this formula to account properly for the antenna-pattern variation over the illuminated area.

Brown, Gary S.↗
NASA NTRS1990

Pressurized-Flat-Interface Heat Exchanger

High thermal conductance obtained without leakage between loops. Heat-exchanger interface enables efficient transfer of heat between two working fluids without allowing fluids to intermingle. Interface thin, flat, and easy to integrate into thermal system. Possible application in chemical or pharmaceutical manufacturing when even trace contamination of process stream with water or other coolant ruins product. Reduces costs when highly corrosive fluids must be cooled or heated.

Voss, F. E.↗