Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Flap noise prediction method for a powered lift system

A method is presented for estimating the noise generated by deflection of the engine exhaust for under-the-wing and over-the-wing versions of an externally blown flap configuration for powered lift. Correlation equations and curves are given for the OASPL and directivity and for spectra scaled to a high bypass 25,000-pound thrust size engine. Data are taken from TF34 engine tests and from large cold flow model tests. The correlations are empirical, and thus application of this prediction procedure is limited to geometrically similar configurations. Application of the method is illustrated by calculated sample footprints.

Clark, B.↗
NASA NTRS1974

Low-speed aerodynamics of the upper-surface blown jet flap

Review of the results of recent wind-tunnel investigations conducted to provide fundamental aerodynamic information on the upper-surface blown jet-flap concept incorporating high-bypass-ratio turbofan engines. The results of the investigations have shown the concept to have aerodynamic performance generally comparable to that of other externally blown high-lift systems. Some of the more critical problem areas associated with this concept are covered, and solutions which have been found for these problems are discussed.

Johnson, J. L., Jr.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1974

Computer experiments on periodic systems identification using rotor blade transient flapping-torsion responses at high advance ratio

Computer experiments are described which used transient responses in flap-bending and torsion of a rotor blade at high advance ratio. It was found that a simple system identification method applying a linear sequential estimator also called equation of motion estimator, is suitable for this periodic system and can be used directly, if only the acceleration data are noise-polluted. In the case where noise is also present in the state-variable data, the direct application of the estimator gave poor results. However after prefiltering the data with a digital Graham filter having a cutoff frequency above the natural blade torsion frequency, the linear sequential estimator successfully recovered the parameters of the periodic coefficient analytical model.

Hohenemser, K. H.↗
NASA NTRS1974

Analysis of a flare-director concept for an externally blown flap STOL aircraft

A flare-director concept involving a thrust-required flare-guidance equation was developed and tested on a moving-base simulator. The equation gives a signal to command thrust as a linear function of the errors between the variables thrust, altitude, and altitude rate and corresponding values on a desired reference flare trajectory. During the simulator landing tests this signal drove either the horizontal command bar of the aircraft's flight director or a thrust-command dot on a head-up virtual-image display of a flare director. It was also used as the input to a simple autoflare system. An externally blown flap STOL (short take-off and landing) aircraft (with considerable stability and control augmentation) was modeled for the landing tests. The pilots considered the flare director a valuable guide for executing a proper flare-thrust program under instrument-landing conditions, but were reluctant to make any use of the head-up display when they were performing the landings visually.

Middleton, D. B.↗
NASA NTRS1975

Wind tunnel investigation of a twin engine straight wing upper surface blown jet flap configuration

An investigation was conducted in a full scale wind tunnel to determine the performance and aerodynamic characteristics of a twin engine, straight wing, upper surface blown jet flap configuration. The model had two simulated high bypass ratio turbofan engines with rectangular nozzles exhausting onto the upper surface of the wing at the 35 percent chord station. The model was tested with an aspect ratio 8.2 wing and with the wingtips removed to give an aspect ratio of 6.0.

Phelps, A. E., III↗
NASA NTRS1975

Wind tunnel investigation of the wake near the trailing edge of a distributed upper-surface-blown flap

An investigation of the flow field near the trailing edge of a distributed upper-surface-blown propulsive-lift transport was conducted in the Langley V/STOL tunnel. This model used blowing slots across the entire wing span to produce a thin jet efflux near the leading edge and at the knee of the flap. Velocity surveys of the flow field were taken near the trailing edge of the model, and are presented as plots of the individual velocity vectors. The test conditions include an angle-of-attack range from 4 deg to 16 deg and a thrust coefficient range from 0 to 1.3 at a free-stream dynamic pressure of 814 Newton per square meter (17 pounds per square foot).

Forsyth, D. R.↗
NASA NTRS1975

Flapping response characteristics of hingeless rotor blades by a gereralized harmonic balance method

Linearized equations of motion for the flapping response of flexible rotor blades in forward flight are derived in terms of generalized coordinates. The equations are solved using a matrix form of the method of linear harmonic balance, yielding response derivatives for each harmonic of the blade deformations and of the hub forces and moments. Numerical results and approximate closed-form expressions for rotor derivatives are used to illustrate the relationships between rotor parameters, modeling assumptions, and rotor response characteristics. Finally, basic hingeless rotor response derivatives are presented in tabular and graphical form for a wide range of configuration parameters and operating conditions.

Peters, D. A.↗
NASA NTRS1975

Effectiveness of spoilers on the GA(W)-1 airfoil with a high performance Fowler flap

Two-dimensional wind-tunnel tests were conducted to determine effectiveness of spoilers applied to the GA(W)-1 airfoil. Tests of several spoiler configurations show adequate control effectiveness with flap nested. It is found that providing a vent path allowing lower surface air to escape to the upper surface as the spoiler opens alleviates control reversal and hysteresis tendencies. Spoiler cross-sectional shape variations generally have a modest influence on control characteristics. A series of comparative tests of vortex generators applied to the (GA-W)-1 airfoil show that triangular planform vortex generators are superior to square planform vortex generators of the same span.

Wentz, W. H., Jr.↗
NASA NTRS1975

Theory of an airfoil equipped with a jet flap under low-speed flight conditions

A theory is developed, for the inviscid, incompressible flow past a thin airfoil equipped with a thin, part-span jet flap, by treating the induced flowfields of the jet and the wing separately and by obtaining the fully coupled solution in an iterative manner. Spanwise variation of the jet vortex strength is assumed to be elliptical in the analysis. Since the method considers the vorticity associated with the jet to be positioned on the computed locus of the jet, the downwash aft of the wing is evaluated as well as forces and moments on the wing. A lifting-surface theory is incorporated for the aerodynamics of the wing. Computational results are presented for a rectangular wing at momentum coefficients above 2.0 and compared with existing linear theories and experimental data. Good agreement is found for small angles of attack, jet-deflection angles, and jet-momentum coefficients where the linear theories and experimental data are applicable. Downwash data at a point in the vicinity of a control surface, the load distribution on the airfoil, and the jet, and the jet location are also presented for representative flight conditons.

Addessio, F. L.↗
NASA NTRS1975

Interim prediction method for externally blown flap noise

An interim procedure for predicting externally blown flap (EBF) noise spectra anywhere below a powered lift aircraft is presented. Both engine-under-the-wing and engine-over-the-wing EBF systems are included. The method uses data correlations for the overall sound pressure level based on nozzle exit area and exhaust velocity along with OASPL directivity curves and normalized one-third-octave spectra. Aircraft motion effects are included by taking into account the relative motion of the source with respect to the observer and the relative velocity effects on source strength.

Dorsch, R. G.↗
NASA NTRS1975

Motion-base simulator study of control of an externally blown flap STOL transport aircraft after failure of an outboard engine during landing approach

A moving-base simulator investigation of the problems of recovery and landing of a STOL aircraft after failure of an outboard engine during final approach was made. The approaches were made at 75 knots along a 6 deg glide slope. The engine was failed at low altitude and the option to go around was not allowed. The aircraft was simulated with each of three control systems, and it had four high-bypass-ratio fan-jet engines exhausting against large triple-slotted wing flaps to produce additional lift. A virtual-image out-the-window television display of a simulated STOL airport was operating during part of the investigation. Also, a simple heads-up flight director display superimposed on the airport landing scene was used by the pilots to make some of the recoveries following an engine failure. The results of the study indicated that the variation in visual cues and/or motion cues had little effect on the outcome of a recovery, but they did have some effect on the pilot's response and control patterns.

Middleton, D. B.↗
NASA NTRS1975

Comparison of model and flight test data for an augmented jet flap STOL research aircraft

Aerodynamic design data for the Augmented Jet Flap STOL Research Aircraft or commonly known as the Augmentor-Wing Jet-STOL Research Aircraft was based on results of tests carried out on a large scale research model in the NASA Ames 40- by 80-Foot Wind Tunnel. Since the model differs in some respects from the aircraft, precise correlation between tunnel and flight test is not expected, however the major areas of confidence derived from the wind tunnel tests are delineated, and for the most part, tunnel results compare favorably with flight experience. In some areas the model tests were known to be nonrepresentative so that a degree of uncertainty remained: these areas of greater uncertainty are identified, and discussed in the light of subsequent flight tests.

Cook, W. L.↗
NASA NTRS1975

A theoretical study of the application of jet flap circulation control for reduction of rotor vibratory forces, addendum

The theoretical potential of a jet flap control system for reducing the vertical and horizontal non-cancelling helicopter rotor blade root shears was investigated. It was determined that the dominant contributor to the rotor power requirements is the requirement to maintain moment trim as well as force trim. It was also found that the requirement to maintain moment trim does not entail a power penalty.

Renka, A. R.↗
NASA NTRS1976

Ground simulation and tunnel blockage for a jet-flapped, basic STOL model tested to very high lift coefficients

Ground effects experiments and large/small-tunnel interference studies were carried out on a model with a 20-inch (50.8 cm) span wing. The wing, which includes a highly deflected knee-blown flap can be fitted with unflapped tips and slats. A low-mounted tailplane can be fitted to the aft fuselage. Three-component balance meaurements, made with a fixed ground equipped with a single boundary-layer blowing slot, were compared with datum, moving-ground results. Good comparisons were obtained up to model blowing momentum coefficients of approximately two, after which the particular floor blowing settings used proved insufficient to prevent floor separation in the vicinity of the model. Skin friction measurements, taken routinely along the floor centerline, proved invaluable during the analysis of results, and their use is recommended as input to determination of floor BLC setting. A careful investigation was made of pitching moments, including tail-on, close-to-ground cases, with favorable results. Drag proved the most sensitive to the change from a moving to the boundary-layer controlled ground.

Hackett, J. E.↗
NASA NTRS1976

An experimental investigation of the flap-lag stability of a hingeless rotor with comparable levels of hub and blade stiffness in hovering flight

An experimental investigation of the flap-lag stability of a hingeless rotor in hovering flight is presented and discussed. The rotor blade and hub configuration were selected such that the hub and blade had comparable levels of bending stiffness. Experimental measurements of the lag damping were made for various values of rotor rotational speed and blade pitch angle. Specifically at a blade pitch angle of 8 deg at three-quarters radius, the lag damping was determined over a range of rotational speeds from 200 RPM to 320 RPM and also over a range of blade pitch angles from 0 deg to 8 deg.

Curtiss, H. C., Jr.↗
NASA NTRS1976

A nonlinear theory for airfoils with trailing-edge jet flap

A nonlinear procedure for computing the pressure distribution on an airfoil with a trailing edge jet flap is described. The method is not restricted to thin airfoils or shallow jet-deflection angles. Correlation with experiment indicates that the characteristics of the pressure distribution are predicted by the theory, but the effect of entrainment is overpredicted with the entrainment coefficient used.

Barger, R. L.↗
NASA NTRS1977

Application of NASA-ARC delayed flap approach procedures to Boeing 727 airplane

The results of an engineering and piloted simulator study to adapt a NASA developed-approach energy management system (AEMS) concept to the B727 are presented. The AEMS concept was developed and flight tested on a CV-990. The purpose of the AEMS is to reduce approach time, fuel, and noise by providing computer-driven cockpit displays to assist the pilot in flying optimized delayed flap approach (DFA) procedures. Development of the DFA flight profiles, the AEMS airborne digital computer algorithm, and associated cockpit displays were studied. Study ground rules and pertinent aerodynamic and noise trend data used in developing the flight profiles are presented. Approach time, fuel, and noise for the DFA are compared to several other types of procedures.

Allison, R. L.↗