Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1955

Reduction of Profile Drag at Supersonic Velocities by the Use of Airfoil Sections Having a Blunt Trailing Edge

A preliminary theoretical and experimental investigation has been made on the aerodynamic characteristics of blunt-trailing-edge airfoils at supersonic velocities. The theoretical considerations indicate that properly designed airfoils with moderately blunt trailing edges can have less profile drag, greater lift-curve slope, and high maximum lift-drag ratio than conventional sections. These predictions have been substantiated by experimental measurements on airfoils of 10-percent-thickness ratio at Mach numbers of 1.5 and 2.0, and at Reynolds numbers between 0.2 and 1.2 million.

Chapman, Dean R↗
NASA NTRS1955

Flight Investigation at Mach Numbers from 0.6 to 1.7 to Determine Drag and Base Pressures on a Blunt Trailing-edge Airfoil and Drag of Diamond and Circular-arc Airfoils at Zero Lift

Results of an exploratory free-flight investigation at zero lift of several rocket-powered drag-research models having rectangular 6-percent-thick wings are presented for a Mach number range of 0.6 to 1.7. Wings having diamond, circular-arc, and blunt-trailing-edge airfoil sections were tested. Pressures over the base of the blunt-trailing-edge airfoil were measured. The drags of all the models were measured and are compared with theory in this paper.

Morrow, John D↗
NASA NTRS1942

Square plate with clamped edges under normal pressure producing large deflections

A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of the solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agree within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.

PLATES-PRESSURE↗
NASA NTRS1933

Wind-tunnel tests on model wing with Fowler flap and specially developed leading-edge slot

An investigation was made in the NACA 7 by 10 foot wind tunnel to find the increase in maximum lift coefficient which could be obtained by providing a model wing with both a Fowler trailing-edge extension flap and a Handley Page type leading-edge slot. A conventional Handley page slot proportioned to operate on the plain wing without a flap gave but a slight increase with the flap; so a special form of slot was developed to work more effectively with the flap. With the best combined arrangement the maximum lift coefficient based on the original area was increased from 3.17, for the Fowler wing, to 3.62. The minimum drag coefficient with both devices retracted was increased in approximately the same proportion. Tests were also made with the special-type slot on the plain wing without the flap. The special slot, used either with or without the Fowler flap, gave definitely higher values of the maximum lift coefficient than the slots of conventional form, with an increase of the same order in the minimum drag coefficient.

WING SLOTS & FLAPS, FOWLER↗
NASA NTRS1947

Investigation of Pressure Distribution over an Extended Leading-Edge Flap on a 42 Degrees Sweptback Wing

Pressure distribution over an extended leading-edge flap on a 42 degree swept-back wing was investigated. Results indicate that the flap normal-force coefficient increased almost linearly with the angle of attack to a maximum value of 3.25. The maximum section normal-force coefficient was located about 30 percent of the flap span outboard of the inboard end and had a value of 3.75. Peak negative pressures built up at the flap leading edge as the angle of attack was increased and caused the chordwise location of the flap center of pressure to be move forward.

Conner, D. William↗
NASA NTRS1954

Effect of Ice Formations on Section Drag of Swept NACA 63A-009 Airfoil with Partical-span Leading-edge Slat for Various Modes of Thermal Ice Protection

Studies were made to determine the effect of ice formations on the section drag of a 6.9-foot-chord 36 degree swept NACA 63A-009 airfoil with partial-span leading-edge slat. In general, the icing of a thin swept airfoil will result in greater aerodynamic penalties than for a thick unswept airfoil. Glaze-ice formations at the leading edge of the airfoil caused large increases in section drag even at liquid-water content of 0.39 gram per cubic meter. The use of an ice-free parting strip in the stagnation region caused a negligible change in drag compared with a completely unheated airfoil. Cyclic de-icing when properly applied caused the drag to decrease almost to the bare-airfoil drag value.

PROTUBERANCES - BODIES↗
NASA NTRS1955

Effect of Reduced Stator-blade Trailing-edge Thickness on Over-all Performance of a Transonic Turbine

A transonic turbine with a stator trailing-edge thickness reduced from 0.030 to 0.010 inch has been investigated experimentally. The performance results indicated an increase in efficiency of 0.6 of a point at design operation, and as much as 2.4 points at off-design conditions, as a result of reducing the trailing-edge thickness. This improvement could only be partially accounted for by the theoretical change in mixing loss for the two stator-blade rows, and it was felt that the improvement was largely due to a reduced amount of low-velocity fluids entering the rotor and the interference effect of these fluids whth the mainstream flow.

Whitney, Warren J↗
NASA NTRS1958

Aerodynamic Characteristics at a Mach Number of 6.8 of Two Hypersonic Missile Configurations, One with Low-Aspect-Ratio Cruciform Fins and Trailing-Edge Flaps and One with a Flared Afterbody and All-Movable Controls

An investigation has been made to determine the aerodynamic characteristics in pitch at a Mach number of 6.8 of hypersonic missile configurations with cruciform trailing-edge flaps and with all-movable control surfaces. The flaps were tested on a configuration having low-aspect-ratio cruciform fins with an apex angle of 5 deg the all-movable controls were mounted at the 46.7-percent body station on a configuration having a 10 deg flared afterbody. The tests were made through an angle-of-attack range of -2 deg to 20 deg at zero sideslip in the Langley 11-inch hypersonic tunnel. The results indicated that the all-movable controls on the flared afterbody model should be capable of producing much larger values of trim lift and of normal acceleration than the trailing-edge -flap configuration. The flared -after body configuration had considerably higher drag than the cruciform-fin model but only slightly lower values of lift drag ratio.

Robinson, Ross B↗
NASA NTRS1952

Experimental Investigation of Base Pressure on Blunt-Trailing-Edge Wings at Supersonic Velocities

Measurements of base pressure are presented for 29 blunt-trailing-edge wings having an aspect ratio of 3.0 and various airfoil profiles. The different profiles comprised thickness ratios between 0.05 and 0.10, boattail angles between -2.9 degrees and 20 degrees, and ratios of trailing-edge thickness to airfoil thickness between 0.2 and 1.0. The tests were conducted at Mach numbers of 1.25, 1.5, 2.0, and 3.1. For each Mach number, the Reynolds number and angle of attack were varied. The lowest Reynolds number investigated was 0.2 x 10(6) and the highest was 3.5 x 10(6). Measurements on each wing were obtained separately with turbulent flow and laminar flow in the boundary layer. Span-wise surveys of the base pressure were conducted on several wings. The results with turbulent boundary-layer flow showed only small effects on base pressure of variations in Reynolds number, airfoil profile shape, boattail angle, and angle of attack. The principal variable affecting the base pressure for turbulent flow was the Mach number.

Chapman, Dean R↗
NASA NTRS1933

The effect of multiple fixed slots and a trailing-edge flap on the lift and drag of a Clark Y airfoil

Lift and drag tests were made on a Clark Y wing equipped with four fixed slots and a trailing-edge flap in the 5-foot vertical wind tunnel of the National Advisory Committee for Aeronautics. All possible combinations of the four slots were tested with the flap neutral and the most promising combinations were tested with the flap down 45 degrees. Considering both the maximum lift coefficient and the speed-range ratio with the flap neutral no appreciable improvement was found with the use of more than the single leading-edge slot. With the flap down 45 degrees a maximum lift coefficient of 2.60 was obtained but the particular slot combination used had a rather large minimum drag coefficient with the flap neutral. With the flap down 45 degrees the optimum combination, considering both the maximum lift coefficient and the speed-range ratio, was obtained with only the two rearmost slots in use. For this arrangement the maximum lift coefficient was 2.44.

Weick, Fred E↗
NASA NTRS1942

Restraint Provided a Flat Rectangular Plate by a Sturdy Stiffener Along an Edge of the Plate

A sturdy stiffener is defined as a stiffener of such proportions that it does not suffer cross-sectional distortion when moments are applied to some part of the cross section. When such a stiffener is attached to one edge of a plate, it will resist rotation of that edge of the plate by means of its torsional properties. A formula is given for the restraint coefficient provided the plate by such a stiffener. This coefficient is required for the calculation of the critical compressive stress of the plate.

Lundquist, Eugene E↗
NASA NTRS1942

Square plate with clamped edges under normal pressure producing large deflections

A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agrees within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.

Levy, Samuel↗
NASA NTRS1949

Summary of section data on trailing-edge high-lift devices

A summary has been made of available data on the characteristics of airfoil sections with trailing-edge high-lift devices. Data for plain, split, and slotted flaps are collected and analyzed. The effects of each of the variables involved in the design of the various types of flap are examined and, in cases where sufficient data are given, optimum configurations are deduced. Wherever possible, the effects of airfoil section, Reynolds number, and leading-edge roughness are shown. For single and double slotted flaps, where a large amount of unrelated data are available, maximum lift coefficients of many configurations are presented in tables.

Cahill, Jones F↗
NASA NTRS1952

Air forces and moments on triangular and related wings with subsonic leading edges oscillating in supersonic potential flow

This analysis treats the air forces and moments in supersonic potential flow on oscillating triangular wings and a series of sweptback and arrow wings with subsonic leading edges and supersonic trailing edges. For the wings undergoing sinusoidal torsional oscillations simultaneously with vertical translations, the linearized velocity potential is derived in the form of a power series in terms of a frequency parameter. This method can be useful for treatment of similar problems for other plan forms and for wings undergoing other sinusoidal motions. For triangular wings, as many terms of such a series expansion as may be derived can be determined; however, the terms after the first few become very cumbersome. Closed expressions that include the reduced frequency to the fifth power, an order which is sufficient for a large class of practical application, are given for the velocity potential and for the components of chordwise section force and moment coefficients. These wings are found to exhibit the possibility of undamped torsional oscillations for certain ranges of Mach number and locations of the axis of rotation. The ranges of these parameters are delineated for triangular wings.

Watkins, Charles E↗
NASA NTRS1958

Area-Suction Boundary-Layer Control as Applied to the Trailing-Edge Flaps of a 35 Degree Swept-Wing Airplane

A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying area-suction boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effect of boundary-layer control in the handling qualities and operation of the airplane, particularly during landing. The wind-tunnel and flight tests indicated that area suction applied to the trailing-edge flaps produced significant increases in flap lift increment. Although the flap boundary-layer control reduced the stall speed only slightly, a reduction in minimum comfortable approach speed of about 12 knots was obtained.

Cook, Woodrow L↗
NASA NTRS1956

Low-speed cascade investigation of loaded leading-edge compressor blades

Six percent thick NACA 63-series compressor-blade sections having a loaded leading-edge A4K6 mean line have been investigated systematically in a two-dimensional porous-wall cascade over a range of Reynolds numbers from 160,000 to 385,000. Blades cambered to have isolated-airfoil lift coefficients of 0.6, 1.2, 1.8, and 2.4 were tested over the usable angle-of-attack range at inlet-air angles of 30 degrees, 45 degrees, and 60 degrees and solidities of 1.0 and 1.5. A comparison with data of NACA RM L51G31, shows that the angle-of-attack operating range is 2 degrees to 4 degrees less than the range for the uniformly loaded section; however, the wake losses near design angle of attack are slightly lower than those for the uniformly loaded section. Except for highly cambered blades at high inlet angles, the 63-(C s oA4K6)06 compressor-blade sections are capable of more efficient operation for moderate-speed subsonic compressors at design angle of attack than are the 65-(C s oa10)10 or the 65-(c s oA2I8b)10 compressor-blade sections. In contrast to the other sections, the loaded leading-edge sections are capable of operating efficiently at the lower Reynolds numbers.

Emery, James C↗
NASA NTRS1956

Formation of a vortex at the edge of a plate

The flow about the plate of infinite width may be represented as a potential flow with discontinuity surfaces which extend from the plate edges. For prescribed form and vortex distribution of the discontinuity surfaces, the velocity field may be calculated by means of a conformal representation. One condition is that the velocity at the plate edges must be finite. However, it is not sufficient for determination of the form and vortex distribution of the surface. However, on the basis of a similitude requirement one succeeds in finding a solution of this problem for the plate of infinite width which is correct for the very beginning of the motion of the fluid. Starting from this solution, the further development of the vortex distribution and shape of the surface are observed in the case of a plate of finite width.

THEORIES - VORTEX↗
NASA NTRS1994

Improved Abutting Edges For Welding In Keyhole Mode

Welds of better quality made, and/or heat input reduced. Improved shapes devised for abutting edges of metal pieces to be joined by plasma arc welding in keyhole mode, in which gas jet maintains molten hole ("keyhole") completely through thickness of weld joint. Edges of metal pieces to be welded together machined to provide required combination gap and shaped, thin sections. Shapes and dimensions chosen to optimize weld in various respects; e.g., to enhance penetration of keyhole or reduce heat input to produce joint of given thickness.

Harwing, Dennis D.↗