Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drag”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Use of a pitot probe for determining wing section drag in flight

A wake traversing probe was used to obtain section drag and wake profile data from the wing of a sailplane. The transducer sensed total pressure defect in the wake as well as freestream total pressure on both sides of the sensing element when the probe moved beyond the wake. Profiles of wake total pressure defects plotted as a function of distance above and below the trailing edge plane were averaged for calculating section drag coefficients for flights at low dynamic pressures.

Saltzman, E. J.↗

Wing-tip vanes as vortex attenuation and induced drag reduction devices

Analytical studies have been conducted to examine the feasibility of utilizing wing tip turbines to remove swirl from the wing trailing vortex, and hence reduce the potential for upset of following aircraft. Energy recovery from the turbines is also analyzed. A computer routine has been developed to permit rapid parametric studies of various tip turbine designs. It is shown that the optimum turbine is a non-rotating set of vanes which reduce swirl and recover energy in the form of reduced overall configuration induced drag. A specific case study indicates a 23% reduction in induced drag for a rectangular wing of aspect ratio 5.33, operated at a lift coefficient at 1.0.

Wentz, W. H., Jr.↗

Reduction of trimmed drag

Methods are reported for reducing the aircraft drag coefficient for a given aircraft lift coefficient, or speed. The emphasis is placed in determining the load distribution between the wing-body combination and the tail which reduces overall drag coefficient. Furthermore, a technique is presented which allows the determination of various aerodynamic and geometric parameters to permit the best location to satisfy inherent stability requirements. Included in the method is the calculation of sensitivity coefficients which indicate the importance of various parameters in achieving specified goals. Preliminary results indicate that such an approach is feasible.

Lutze, F. H., Jr.↗

Minimum wave drag for arbitrary arrangements of wings and bodies

Various arrangements of wings and bodies designed to provide favorable wave interference at supersonic speeds lead to the problem of determining the minimum possible value of the wave resistance obtainable by any disposition of the elements of an aircraft within a definitely prescribed region. Under the assumptions that the total lift and the total volume of the aircraft are given, conditions that must be satisfied if the drag is to be a minimum are found. The report concludes with a discussion of recent developments of the theory which lead to an improved understanding of the drag associated with the production of lift.

Jones, R. T.↗

Inlet spillage drag tests and numerical flow-field analysis at subsonic and transonic speeds of a 1/8-scale, two-dimensional, external-compression, variable-geometry, supersonic inlet configuration

Accurate spillage drag and pressure data are presented for a realistic supersonic inlet configuration. Results are compared with predictions from a finite-differencing, inviscid analysis computer procedure. The analytical technique shows good promise for the evaluation of inlet drag, but necessary refinements were identified. A detailed description of the analytical procedure is contained in the Appendix.

Hawkins, J. E.↗

Effect of Reynolds number on the subsonic boattail drag of several wing-body configurations

An investigation was conducted in a transonic cryogenic tunnel to determine the effect of varying Reynolds number on the boattail drag of several wing-body configurations. This study was made at 0 deg angle of attack at Mach numbers from 0.6 to 0.9 for Reynolds numbers up to 67 x 1 million (based on distance from the nose to the start of the boattail). Results indicate that as the Reynolds number was increased the boattail static pressure coefficients in the expansion region of the boattail became more negative while those in the recompression region became more positive. Results show that there was only a small effect of Reynolds number of boattail pressure drag.

Reubush, D. E.↗

A vortex-lattice method for the mean camber shapes of trimmed noncoplanar planforms with minimum vortex drag

A new subsonic method has been developed by which the mean camber surface can be determined for trimmed noncoplanar planforms with minimum vortex drag. This method uses a vortex lattice and overcomes previous difficulties with chord loading specification. A Trefftz plane analysis is utilized to determine the optimum span loading for minimum drag, then solved for the mean camber surface of the wing, which provides the required loading. Sensitivity studies, comparisons with other theories, and applications to configurations which include a tandem wing and a wing winglet combination have been made and are presented.

Lamar, J. E.↗

Minimum trim drag design for interfering lifting surfaces using vortex-lattice methodology

A new method has been developed by which the mean camber surface can be determined for trimmed noncoplanar planforms with minimum vortex drag under subsonic conditions. The method uses a vortex lattice and overcomes previous difficulties with chord loading specification; it uses a Trefftz plane analysis to determine the optimum span loading for minimum drag, then solves for the mean camber surface of the wing which will provide the required loading. Pitching-moment or root-bending-moment constraints can be employed as well at the design lift coefficient. Sensitivity studies of vortex-lattice arrangement have been made with this method and are presented. Comparisons with other theories show generally good agreement. The versatility of the method is demonstrated by applying it to (1) isolated wings, (2) wing-canard configurations, (3) a tandem wing, and (4) a wing-winglet configuration.

Lamar, J. E.↗

An investigation of drag reduction on box-shaped ground vehicles

A wind tunnel investigation was conducted to determine the reduction in drag which could be obtained by making various configuration changes to a box-shaped ground vehicle. Tests were conducted at yaw (relative wind) angles of 0, 5, 10, 20, and 30 degrees and Reynolds numbers of 300,000 to 850,000. The power required to overcome the aerodynamic drag was reduced by a maximum of 73% for a head wind for the best configuration relative to the smooth bottom box-shape, or 75% relative to the rough bottom box-shape. The reduction for a 20 MPH wind at 30 deg to the vehicle path was, respectively, 77% and 79%.

Muirhead, V. U.↗

Drag coefficient of 20-degree conical ribbon parachute

An empirical formula for the steady-state drag coefficient of a 20-degree conical ribbon parachute is developed. The derived expression takes into account the effect of suspension line length and geometric porosity within the limits of practical design. Also included are factors which provide drag reduction due to skirt reefing and the wake behind a primary body. The calculated values are in agreement with the available experimental results.

Utreja, L. R.↗

Mass center estimation of a drag-free satellite

The mass center location of a spinning drag-free satellite can be estimated because there is control required to accelerate the mass center along the axis of spin as long as there is some nutation in the spinning motion. Linear and nonlinear models are compared and observability discussed. Online estimation fails when nutation is damped so an offline mechanization is proposed. A new sensor has been designed to permit greater relative motion than was possible on the drag-free satellite flown in 1972 (JH-1). Experimental laboratory results using a spinning vehicle with the new sensor mounted 30 cm from a spherical air bearing support are presented which confirm earlier simulation results.

Sanz Fernandez De Cordova, S.↗

Exospheric density measurements from the drag-free satellite Triad

The Triad satellite is maintained within 1 mm of its proof mass (a small metal ball) in a purely gravitational orbit, using a drag-free control system, named Discos, as the disturbance compensation system. The Discos proof mass is surrounded by an outer shell which holds fuel tanks and cold gas jets. The shell shields the proof mass from such nongravitational forces as radiation pressure, atmospheric drag, and micrometeorite impact. Whenever these forces displace the outer shell relative to the proof mass, an error signal is generated by a capacitive bridge sensor, and the satellite is propelled by gas jets to remain centered on the proof mass when the error reaches 1 mm. Local atmospheric densities near 800 km were measured, using ball position data, and the observed accelerations were corrected for the effects of solar radiation pressure. The measured densities reveal a greater dependence on latitude than that indicated by balloon satellites, and also a dependence on longitude. Only a small dependence on Kp, however, was observed in the region where the measurements were made.

Moe, K.↗

Prediction of the drag coefficient of a 20-degree conical ribbon parachute

An empirical formula for the steady state drag coefficient of a 20 degree conical ribbon parachute is developed. The derived expression takes into account the effect of suspension line length and geometric porosity within the limits of practical design. Also included are factors which provide drag reduction due to skirt reefing and the wake behind a primary body. The calculated values are in agreement with the available experimental results.

Utreja, L. R.↗

Boron-epoxy-reinforced titanium aircraft landing-gear drag strut

The structural performance of a boron-epoxy-reinforced titanium drag strut, containing a bonded scarf joint and designed to the criteria of a large commercial transport, has been evaluated experimentally and analytically. The strut was exposed to two lifetimes of fatigue loading and was statically loaded to the tensile and compressive design ultimate loads. Throughout the test program no evidence of any damage in the drag strut was detected by strain-gage measurements, ultrasonic inspection, or visual observation. The bonded joint was analyzed using the NASTRAN computer program. A comparison of the strains predicted by the NASTRAN computer program with the experimentally determined values shows excellent agreement. An analytical study indicated that the nonlinear behavior of a structural spacer at each end of the strut could be explained by the inelastic behavior and possible creep of the adhesive.

Howell, W. E.↗

Advanced airfoil design empirically based transonic aircraft drag buildup technique

To systematically investigate the potential of advanced airfoils in advance preliminary design studies, empirical relationships were derived, based on available wind tunnel test data, through which total drag is determined recognizing all major aircraft geometric variables. This technique recognizes a single design lift coefficient and Mach number for each aircraft. Using this technique drag polars are derived for all Mach numbers up to MDesign + 0.05 and lift coefficients -0.40 to +0.20 from CLDesign.

Morrison, W. D., Jr.↗

Calculations, and comparison with an ideal minimum, of trimmed drag for conventional and canard configurations having various levels of static stability

Classical drag equations were used to calculate total and induced drag and ratios of stabilizer lift to wing lift for a variety of conventional and canard configurations. The Flight efficiencies of such configurations that are trimmed in pitch and have various values of static margin are evaluated. Classical calculation methods are compared with more modern lifting surface theory.

Mclaughlin, M. D.↗

Determining the Lift and Drag Distributions on a Three-Dimensional Airfoil from Flow-Field Velocity Surveys

The application of the incompressible momentum integral equation to a three-dimensional airfoil was reviewed to interpret the resulting equations in a way that suggests a reasonable experimental technique for determining the spanwise distributions of lift and drag. Consideration was given to constraints that must be placed on the character of the vortex wake structure shed by the wing, to provide the familiar relationship between lift and bound vorticity. It is shown that the induced drag distribution is not directly measurable, but can be obtained, via the lift distribution, approximately for a deflected wake and exactly for a planar wake. Moreover, it is shown that it is only necessary to survey a short distance above and below the wing trailing edge. Examples are presented for several typical loading distributions and the results of a numerical simulation of the suggested experiment are discussed.

Orloff, K. L.↗

A possible experiment with two counter-orbiting drag-free satellites to obtain a new test of Einstein's general theory of relativity and improved measurements in geodesy

In 1918, Lense and Thirring calculated that a moon in orbit around a massive rotating planet would experience a nodal dragging effect due to general relativity. We describe an experiment to measure this effect by means of two counter-orbiting drag-free satellites in polar orbit about the earth. For a 2-1/2 year experiment, the measurement should approach an accuracy of 1%. An independent measurement of the geodetic precession of the orbit plane due to the motion about the sun may also be possible to about 10% accuracy. In addition to precision tracking data from existing ground stations, satellite-to-satellite Doppler data are taken at points of passing near the poles to yield an accurate measurement of the separation distance between the two satellites. New geophysical information on both earth harmonics and tidal effects is inherent in this polar ranging data.

Van Patten, R. A.↗