Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diameter distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

In situ measurements of particulate number density and size distribution from an aircraft

Two different commercial particulate measuring instruments were flown aboard the NASA Convair 990. A condensation nuclei monitor was utilized to measure particles larger than approximately 0.003 micron in diameter. A specially designed pressurization system was used with this monitor at cabin altitude pressure. A near-forward light scattering counter was used to measure the number and size distribution particles in the size range from 0.5 to 5 microns and greater in diameter. Considerable variation in number density was encountered for both classes of particles at the test altitudes ranging from 5 to 12 km. Presence of clouds could be detected by the light scattering instrument because large numbers of particles would then be registered by the instrument, especially in the size range above 5.0 microns in diameter.

Briehl, D.↗

Effect of Reynolds Number on the Force and Pressure Distribution Characteristics of a Two-Dimensional Lifting Circular Cylinder

A two-dimensional lifting circular cylinder has been tested over a Mach number range from 0.011 to 0.32 and a Reynolds number range from 135,000 to 1,580,000 to determine the force and pressure distribution characteristics. Two flaps having chords of 0.37 and 6 percent of the cylinder diameter, respectively, and attached normal to the surface were used to generate lift. A third configuration which had 6-percent flaps 1800 apart was also investigated. All flaps were tested through a range of angular positions. The investigation also included tests of a plain cylinder without flaps. The lift coefficient showed a wide variation with Reynolds number for the 6-percent flap mounted on the bottom surface at the 50-percent-diameter station, varying from a low of about 0.2 at a Reynolds number of 165,000 to a high of 1.54 at a Reynolds number of 350,000 and then decreasing almost linearly to a value of 1.0 at a Reynolds number of 1,580,000. The pressure distribution showed that the loss of lift with Reynolds number above the critical was the result of the separation point moving forward on the upper surface. Pressure distributions on a plain cylinder also showed similar trends with respect to the separation point. The variation of drag coefficient with Reynolds number was in direct contrast to the lift coefficient with the minimum drag coefficient of 0.6 occurring at a Reynolds number of 360,000. At this point the lift-drag ratios were a maximum at a value of 2.54. Tests of a flap with a chord of 0.0037 diameter gave a lift coefficient of 0.85 at a Reynolds number of 520,000 with the same lift-drag ratio as the larger flap but the position of the flap for maximum lift was considerably farther forward than on the larger flap. Tests of two 6-percent flaps spaced 180 deg apart showed a change in the sign of the lift developed for angular positions of the flap greater than 132 deg at subcriti- cal Reynolds numbers. These results may find use in application to air- craft using forebody strakes. The drag coefficient developed by the flaps when normal to the relative airstream was approximately equal to that developed by a flat plate in a similar attitude.

Lockwood, Vernard E.↗

Using GRIDVIEW to Better Understand the Early Bombardment History of the Moon, Mars and Earth

For more than a decade we have used GRIDVIEW to help analyze topographic and related data for Mars and more recently for the Moon. Our focus has been to employ the stretching, contouring, profiling, circle-fitting and other capabilities of GRIDVIEW to search for Quasi-Circular Depressions (CTAs) in MOLA, LOLA and other topographic data, and for Circular Thin Areas (CTAs) in Mars and Moon model crustal thickness data. Both QCDs and CTAs likely represent buried or obscured impact craters not readily visible in image data. We found clear evidence for a much larger population of buried impact craters in the northern lowlands of Mars (Frey et al. 2002), suggesting that part of the Red Planet is not significantly younger than the southern highlands. Edgar and Frey (2008) found that the N(300) crater retention ages of both areas were essentially identical, a conclusion confirmed by Wyatt (unpublished data) using more recent crustal thickness data for Mars. MOLA topographic data and MOLA-derived crustal thickness data were used to both identify a large number of previously unrecognized very large impact basins (D> 1000 km) on Mars and to determine relative crater retention ages for them (Frey, 2008). The distribution of N(300) CRAs suggested most formed in a relatively short interval of time. This dating also suggested the main magnetic field of Mars disappeared during this period (Lillis et al., 2008), because only the youngest basins systematically lack a remagnetized signature. Similar QCD and CTA analysis of first Clementine (Frey, 2011) and more recently LOLA topographic and LOLA-derived crustal thickness data for the Moon (Frey et al., 2011) revealed a significantly larger population of impact basins > 300 km in diameter than previously known. N(50) CRAs suggest a two-peak distribution of ages (Frey, 2012). An improved counting process confirms the two peaks, perhaps indicating both a pre-Nectaris Early Heavy Bombardment (EHB) as well as a Late Heavy Bombardment (LHB) on the Moon (Frey and Burgess, 2012, this meeting), with obvious implications for the early bombardment history of the Earth.

Frey, Herbert↗

Large Impact Basins on Mercury: Global Distribution, Characteristics, and Modification History from MESSENGER Orbital Data

The formation of large impact basins (diameter D greater than or equal to 300 km) was an important process in the early evolution of Mercury and influenced the planet's topography, stratigraphy, and crustal structure. We catalog and characterize this basin population on Mercury from global observations by the MESSENGER spacecraft, and we use the new data to evaluate basins suggested on the basis of the Mariner 10 flybys. Forty-two certain or probable impact basins are recognized a few additional basins that may have been degraded to the point of ambiguity are plausible on the basis of new data but are classified as uncertain. The spatial density of large basins (D greater than or equal to 500 km) on Mercury is lower than that on the Moon. Morphological characteristics of basins on Mercury suggest that on average they are more degraded than lunar basins. These observations are consistent with more efficient modification, degradation, and obliteration of the largest basins on Mercury than on the Moon. This distinction may be a result of differences in the basin formation process (producing fewer rings), greater relaxation of topography after basin formation (subduing relief), and/or higher rates of volcanism during the period of heavy bombardment on Mercury compared to the Moon (burying basin rings and interiors).

Fassett, Caleb I.↗

Diagnostic Systems in the Muon $g-2$ experiment at Fermilab

The muon anomalous magnetic moment, $a_\mu=\frac{g-2}{2}$, is a low-energy observable which can be both measured and computed to high precision, making it a sensitive test of the Standard Model and a probe for new physics. This anomaly was measured with a precision of $0.20$~parts per million (ppm) by the Fermilab's Muon g-2 (E989) experiment. The final goal of the E989 experiment is to reach a precision of $0.14$~ppm. The experiment is based on the measurement of the muon spin anomalous precession frequency, $\omega_a$, based on the arrival time distribution of high-energy decay positrons observed by 24 electromagnetic calorimeters, placed around the inner circumference of a $14$~m diameter storage ring, and on the precise knowledge of the storage ring magnetic field and of the beam time and space distribution. Achieving this level of precision requires strict control over systematics, which is ensured through several diagnostic devices. At the accelerator level, these devices monitor the quality of the injected beam (e.g., verifying that it has the correct momentum), while at the detector level, they track both the magnetic field and the gain of the calorimeters. In this work the devices and techniques used by the E989 experiment will be presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Large craters on the meteoroid and space debris impact experiment

The distribution around the Long Duration Exposure Facility (LDEF) of 532 large craters in the Al plates from the Meteoroid and Space Debris Impact Experiment (S0001) is discussed along with 74 additional large craters in Al plates donated to the Meteoroid and Debris Special Investigation Group by other LDEF experimenters. The craters are 0.5 mm in diameter and larger. Crater shape is discussed. The number of craters and their distribution around the spacecraft are compared with values predicted with models of the meteoroid environment and the manmade orbital debris environment.

Humes, Donald H.↗

Density and temperature distributions in the plasma expanding from an exploded wire in vacuum

The plasma expansion from an exploded wire with characteristic times of energy deposition in the wire of tens of microseconds was studied. The probe method was used to measure the plasma temperature and plasma density distributions. Tungsten wires 25, 50, 75, and 125 {mu}m in diameter and a copper wire 100 {mu}m in diameter were used. The waveforms of discharge voltage U{sub d}, discharge current I{sub d}, and floating potential showed that U{sub d} was close to a constant, while I{sub d} decreased, indicating that the wire resistance increased until plasma appeared. Immediately after the appearance of plasma, I{sub d} was observed to peak, while the voltage decreased stepwise from {approx}110 to about 70 V. A relatively high electron temperature (about 12 eV) was observed in the expanding plasma even at r=2 cm from the wire axis. The plasma density was a maximum of 2x10{sup 13} cm{sup -3} at r=2 cm, and it decreased with increasing r. For r<2 cm, unusual electrical parameters were observed, indicating the probe activity and a significantly increased plasma density in the region close to the wire core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mesoscale simulation of granular materials under weak shock compaction–pore size distribution effects

This research established a systematic method to generate various pore-size distributions (PSDs) and studied the effect of PSDs on the shock compaction response of granular materials using two-dimensional mesoscale simulations under identical porosity. Simulations utilized various PSDs for three particle shapes (circle, ellipse, and square). Contacting particle configurations using three PSDs, characterized by spatially uniform distributed pores to heterogeneous distributed pores, and non-contacting particle configurations under a single case of PSD were tested. The PSD of generated particle sets was characterized using coordination number, mean diameter, and bimodality coefficient as statistical metrics. Mesoscale simulations showed that regardless of the conditions of pore distributions, shock compaction of granular materials consistently demonstrates a precursor, shock compaction front, and end. However, the shock compaction velocity of contacting particles was dependent on the PSDs despite the constant initial porosity. The compaction velocity was faster in particle configurations with relatively uniform pore distributions than in heterogeneous pore distributions, which our study demonstrated can be attributed to particle rearrangement during compaction. Circular-shaped particles had high sensitivity in shock compaction response to the various PSDs. Furthermore, a contacting particle configuration tended to propagate the shock compaction wave relatively faster than particles that were in a non-contact configuration. This study established the relative importance of considering PSD as a metric over the coordination number in studies of the shock compaction response of granular materials. Further, insights are provided on the evolving shock substructure to characterize the shock compaction response of granular materials.

36 MATERIALS SCIENCE↗

A model of the origin of the Jovian ring

Assuming that the micron-sized particles making up the bright Jovian ring are fragments of erosive collisions between micrometeoroid projectiles and large parent bodies, a physical model of the ring is calculated. This leads to a well-defined size distribution for the ejecta, whose optical properties can be compared with observation. The (most likely silicate) ejecta material maximum diameter is estimated to be 0.1 micron, and most likely the result of Io volcanic activity. The impact model's determination of ejecta size distribution in turn determines the structure of the ring, with the largest ejecta forming the bright ring, medium-sized ejecta forming a disk that extends to the Jovian atmosphere, and small ejecta forming a faint halo whose structure is dominated by electromagnetic forces.

Gruen, E.↗

Extending the Capabilities of Single Particle Mass Spectrometry: II. Measurements of Aerosol Particle Density without DMA

Particle density is an important and useful property that is difficult to measure because it usually 5 requires separate instruments to measure two particle attributes. As density measurements are 6 often performed on size-classified particles, they are hampered by low particle numbers, and 7 hence poor temporal resolution. We present here a new method for measuring particle densities 8 using our single particle mass spectrometer, SPLAT. This method takes advantage of the fact 9 that the detection efficiency in our single particle mass spectrometer drops off very rapidly as the 10 particle size decreases below ~125 nm creating a distinct sharp feature on the small particle side 11 of the vacuum aerodynamic size distribution. Thus, the two quantities needed to determine 12 particle density, the particle diameter and vacuum aerodynamic diameter, are known. We first 13 test this method on particles of known composition and find that the densities it yields are 14 sufficiently accurate. We then apply the method to obtain the densities of particles that were 15 characterized during an airborne field campaign. In addition, we show that the distinctive 16 features of the vacuum aerodynamic size distribution can be used to characterize the instrument 17 detection efficiency as a function of particle size. In general, the method presented here reduces 18 complexity and yields information with high temporal resolution while the instrument is 19 collecting routine data on particle size and composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Use of Cloud Radar Doppler Spectra to Evaluate Stratocumulus Drizzle Size Distributions in Large-Eddy Simulations with Size-Resolved Microphysics

Abstract A case study of persistent stratocumulus over the Azores is simulated using two independent large-eddy simulation (LES) models with bin microphysics, and forward-simulated cloud radar Doppler moments and spectra are compared with observations. Neither model is able to reproduce the monotonic increase of downward mean Doppler velocity with increasing reflectivity that is observed under a variety of conditions, but for differing reasons. To a varying degree, both models also exhibit a tendency to produce too many of the largest droplets, leading to excessive skewness in Doppler velocity distributions, especially below cloud base. Excessive skewness appears to be associated with an insufficiently sharp reduction in droplet number concentration at diameters larger than ~200 μm, where a pronounced shoulder is found for in situ observations and a sharp reduction in reflectivity size distribution is associated with relatively narrow observed Doppler spectra. Effectively using LES with bin microphysics to study drizzle formation and evolution in cloud Doppler radar data evidently requires reducing numerical diffusivity in the treatment of the stochastic collection equation; if that is accomplished sufficiently to reproduce typical spectra, progress toward understanding drizzle processes is likely.

54 ENVIRONMENTAL SCIENCES↗

Streamwise flow and heat transfer distributions for jet array impingement with crossflow

Two-dimensional arrays of circular jets of air impinging on a heat transfer surface parallel to the jet orifice plate are considered. The air, after impingement, is constrained to exit in a single direction along the channel formed by the surface and the jet plate. The downstream jets are subjected to a crossflow originating from the upstream jets. Experimental and theoretical results obtained for streamwise distributions of jet and crossflow velocities are presented and compared. Measured Nusselt numbers resolved to one streamwise hole spacing are correlated with individual spanwise row jet Reynolds numbers and crossflow-to-jet velocity ratios. Correlations are presented for both inline and staggered hole patterns including effects of geometric parameters: streamwise hole spacing, spanwise hole spacing, and channel height, normalized by hole diameter. The physical mechanisms influencing heat transfer coefficients as a function of flow distribution and geometric parameters are also discussed.

Florschuetz, L. W.↗

Height and altitude distribution of large volcanoes on Venus

Magellan data reveal 156 large volcanoes on Venus (greater than 100 km in diameter) which range in height from 300 m to 5.55 km, with an average height of 1.42 km. On the basis of theory it has been predicted that the development of neutral buoyancy zones (NBZ) on Venus and thus the resulting volcanic deposits are strongly influenced by the altitude-controlled variations in surface pressure. The distribution and height of these large volcanoes as a function of altitude was examined to begin to test these predications. Although large volcanoes are relatively uniformly distributed in altitude, there may be a slight paucity of volcanoes at the lowest elevations and a slight surplus at mid-altitudes. In addition, it is observed that the volcanoes at the highest altitudes tend to be the tallest. The observed distributions at low-mid altitudes is consistent with the prediction of NBZ theory. The high altitude distribution and heights, however, emphasize the necessity of considering other factors, such as tectonic setting, edifice age, magma supply, and thermal gradient, in describing the location and development of large volcanoes on Venus.

Keddie, S. T.↗

Aerosol size spectrum analysis using relaxation time measurement

An experimental method has been developed to measure the dynamic relaxation times of aerosol particles. The particle relaxation time (tau-p) is determined from the ratio of the velocity amplitude of an aerosol particle (v-p) to the velocity amplitude of the medium (u-g) while the aerosol is subjected to acoustic excitation of a known frequency. A differential laser Doppler velocimeter is used to measure v-p, while a microphone is used to measure u-g. From the value of tau-p, the aerodynamic diameter of the particle can be determined if the particle density is known. The method can be applied to real-time in situ measurement of size distribution of an aerosol containing both solid particles and liquid droplets in the range of 0.1-10.0-micron diameters.

Kirsch, K. J.↗

Modifications to the JET Shattered Pellet Injector to Optimize Disruption Mitigation Experiments for Supporting ITER’s DMS Design

Shattered pellet injection (SPI) experiments on Joint European Torus (JET) are an important element in determining the physics basis for mitigating disruptions in ITER. Here, the initial design of the JET SPI system included three barrels to produce pellets with diameters of 4.5, 8.1, and 12.5 mm. The variability of the pellet speed by operating with and without a mechanical punch was limited and led to poor pellet integrity, so the mechanical punch was removed. Fragment size distribution is a function of pellet speed and the desire to change the resulting fragment size distribution was not originally a requirement. After the first set of SPI experiments on JET, different pellet sizes were considered to enable dual injection experiments with identical pellet diameters. It was also determined that speed control is necessary to improve experimental repeatability and to determine how the fragment size distribution impacts mitigation performance. Two barrels were fabricated to form pellets of 10 mm diameter and a third to form an 8.1 mm diameter pellet. New propellant valves were also fabricated and characterized to improve repeatability and overall performance. To have fine control of pellet speed, inserts to reduce the breech volume were fabricated and installed. Laboratory testing was conducted to ensure pellet release and provide a comparison of propellant gas delivered versus pellet speeds for a range of pellet types and mixtures. This article will also discuss how lessons learned from the JET SPI modifications can be applied to other SPI systems, such as the ITER SPI system, as controlling pellet release with the least amount of propellant gas is essential for optimal SPI effectiveness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A distribution model for the aerial application of granular agricultural particles

A model is developed to predict the shape of the distribution of granular agricultural particles applied by aircraft. The particle is assumed to have a random size and shape and the model includes the effect of air resistance, distributor geometry and aircraft wake. General requirements for the maintenance of similarity of the distribution for scale model tests are derived and are addressed to the problem of a nongeneral drag law. It is shown that if the mean and variance of the particle diameter and density are scaled according to the scaling laws governing the system, the shape of the distribution will be preserved. Distributions are calculated numerically and show the effect of a random initial lateral position, particle size and drag coefficient. A listing of the computer code is included.

Fernandes, S. T.↗

SU-F-P-37: Implementation of An End-To-End QA Test of the Radiation Therapy Imaging, Planning and Delivery Process to Identify and Correct Possible Sources of Deviation

Purpose: To implement an end-to-end QA test of the radiation therapy imaging, planning and delivery process, aimed to assess the dosimetric agreement accuracy between planned and delivered treatment, in order to identify and correct possible sources of deviation. To establish an internal standard for machine commissioning acceptance. Methods: A test involving all steps of the radiation therapy: imaging, planning and delivery process was designed. The test includes analysis of point dose and planar dose distributions agreement between TPS calculated and measured dose. An ad hoc 16 cm diameter PMMA phantom was constructed with one central and four peripheral bores that can accommodate calibrated electron density inserts. Using Varian Eclipse 10.0 and Elekta XiO 4.50 planning systems, IMRT, RapidArc and 3DCRT with hard and dynamic wedges plans were planned on the phantom and tested. An Exradin A1SL chamber is used with a Keithley 35617EBS electrometer for point dose measurements in the phantom. 2D dose distributions were acquired using MapCheck and Varian aS1000 EPID.Gamma analysis was performed for evaluation of 2D dose distribution agreement using MapCheck software and Varian Portal Dosimetry Application.Varian high energy Clinacs Trilogy, 2100C/CD, 2000CR and low energy 6X/EX where tested.TPS-CT# vs. electron density table were checked for CT-scanners used. Results: Calculated point doses were accurate to 0.127% SD: 0.93%, 0.507% SD: 0.82%, 0.246% SD: 1.39% and 0.012% SD: 0.01% for LoX-3DCRT, HiX-3DCRT, IMRT and RapidArc plans respectively. Planar doses pass gamma 3% 3mm in all cases and 2% 2mm for VMAT plans. Conclusion: Implementation of a simple and reliable quality assurance tool was accomplished. The end-to-end proved efficient, showing excellent agreement between planned and delivered dose evidencing strong consistency of the whole process from imaging through planning to delivery. This test can be used as a first step in beam model acceptance for clinical use.

60 APPLIED LIFE SCIENCES↗

Flow and Noise Control in High Speed and High Reynolds Number Jets Using Plasma Actuators

The idea of manipulating flow to change its characteristics is over a century old. Manipulating instabilities of a jet to increase its mixing and to reduce its radiated noise started in the 1970s. While the effort has been successful in low-speed and low Reynolds number jets, available actuators capabilities in terms of their amplitude, bandwidth, and phasing have fallen short in control of high-speed and high Reynolds number jets of practical interest. Localized arc filament plasma actuators have recently been developed and extensively used at Gas Dynamics and Turbulence Laboratory (GDTL) for control of highspeed and high Reynolds number jets. While the technique has been quite successful and is very promising, all the work up to this point had been carried out using small high subsonic and low supersonic jets from a 2.54 cm diameter nozzle exit with a Reynolds number of about a million. The preliminary work reported in this paper is a first attempt to evaluate the scalability of the technique. The power supply/plasma generator was designed and built in-house at GDTL to operate 8 actuators simultaneously over a large frequency range (0 to 200 kHz) with independent control over phase and duty cycle of each actuator. This allowed forcing the small jet at GDTL with azimuthal modes m = 0, 1, 2, 3, plus or minus 1, plus or minus 2, and plus or minus 4 over a large range of frequencies. This power supply was taken to and used, with minor modifications, at the NASA Nozzle Acoustic Test Rig (NATR). At NATR, 32 actuators were distributed around the 7.5 in. nozzle (a linear increase with nozzle exit diameter would require 60 actuators). With this arrangement only 8 actuators could operate simultaneously, thus limiting the forcing of the jet at NATR to only three azimuthal modes m = plus or minus 1, 4, and 8. Very preliminary results at NATR indicate that the trends observed in the larger NASA facility in terms of the effects of actuation frequency and azimuthal modes are similar in both small GDTL and larger NASA jets. However, the actuation authority seems to fall short in the larger jet at higher Mach numbers, resulting in decreased amplitude response compared to the small jet, which is attributed at this point to the lack of sufficient number of actuators. The preliminary results seem also to suggest that amplitude of actuation tones is similar in both the small and larger jets.

Samimy, M.↗