SEARCH · Engineering Papers

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Numerical Simulation of Vitiation Effects on a Hydrogen-Fueled Dual-Mode Scramjet

The Wind-US computational fluid dynamics (CFD) flow solver was used to simulate dual-mode direct-connect ramjet/scramjet engine flowpath tests conducted in the University of Virginia (UVa) Supersonic Combustion Facility (SCF). The objective was to develop a computational capability within Wind-US to aid current hypersonic research and provide insight to flow as well as chemistry details that are not resolved by instruments available. Computational results are compared with experimental data to validate the accuracy of the numerical modeling. These results include two fuel-off non-reacting and eight fuel-on reacting cases with different equivalence ratios, split between one set with a clean (non-vitiated) air supply and the other set with a vitiated air supply (12 percent H2O vapor). The Peters and Rogg hydrogen-air chemical kinetics model was selected for the scramjet simulations. A limited sensitivity study was done to investigate the choice of turbulence model and inviscid flux scheme and led to the selection of the k-epsilon model and Harten, Lax and van Leer (for contact waves) (HLLC) scheme for general use. Simulation results show reasonably good agreement with experimental data and the overall vitiation effects were captured.

Vyas, Manan A.↗

NASA NTRS1988

The numerical simulation of transonic separated flow about the complete F-16A

The thin-layer, Reynolds-averaged, Navier-Stokes equations are used to simulate the transonic viscous flow about the complete F-16A fighter aircraft. These computations demonstrate how computational fluid dynamics (CFD) can be used to simulate turbulent viscous flow about realistic aircraft geometries. A zonal grid approach is used to provide adequate viscous grid clustering on all aircraft surfaces. Zonal grids extend inside the F-16A inlet and up to the compressor face while power on conditions are modeled by employing a zonal grid extending from the exhaust nozzle to the far field. A simple solution adaptive grid procedure is used on the wing surface and good agreement with experimental data is obtained. Computations for the F-16A in side slip are also presented.

Flores, Jolen↗

DOE OSTI2022

CFD simulations of electric motor end ring cooling for improved thermal management

Proper thermal management of an electric motor for vehicle applications extends its operating range. One cooling approach is to impinge Automatic Transmission Fluid (ATF) onto the rotor end ring. Increased ATF coverage correlates to enhanced heat transfer. Computational Fluid Dynamics (CFD) analytical tools provide a mechanism to assess motor thermal management prior to hardware fabrication. The complexity of the fluid flow (e.g., jet atomization, interface tracking, wall impingement) and heat transfer makes these simulations challenging. Computational costs are high when solving these flows on high-speed rotating meshes. Typically, a Volume-of Fluid (VOF) technique (i.e., two-fluid system) is used to resolve ATF dynamics within this rotating framework. Suitable numerical resolution of the relevant physics for thin films under strong inertial forces at high rotor speeds is computationally expensive, further increasing the run times. In this work, a numerical study of rotor-ring cooling by ATF is presented using a patent automated Cartesian cut-cell based method coupled with Automatic Mesh Refinement (AMR). This approach automatically creates the Cartesian mesh on-the-fly and can effectively handle complex rotating geometries by adaptively refining the mesh based on local gradients in the flow field which results in better resolution of the air-ATF interface. A Single non-inertial Reference Frame (SRF) approach is used to account for the rotating geometry and to further improve the overall computational efficiency. Quasi-steady state conditions are targeted in the analysis of the results. Important physics such as ATF jet structure, velocity detail near the air-jet interface, ATF coverage/accumulation on the ring surface, and cooling capacity are presented for a low-resolution Reynolds averaged Navier-Stokes (RANS), high-resolution RANS, and high-resolution Large-Eddy Simulation (LES) models. Computations are scaled over hundreds of cores on a supercomputer to maximize turnaround time. Each numerical approach is shown to capture the general trajectory of the oil jet prior to surface impingement. The high-resolution LES simulation, however, is superior in capturing small scale details and heat transfer between the free jet and surrounding air.

42 ENGINEERING↗

DOE OSTI2024

Accelerating transients with NekRS: GPU overlapping domain implementation and multi-rate timestepping

The simulation of nuclear transients using Computational Fluid Dynamics (CFD) presents significant computational challenges due to the inherent complexity and the wide separation in temporal scales between various flow physical phenomena. These disparities lead to high computational costs, often making the simulation of transients impractical without advanced techniques. Consequently, multiple research initiatives are being pursued by the NEAMS thermal-hydraulic area, some driven by academic institutions and some by national laboratories. Overall, they are exploring novel methods to make transient simulations more feasible and efficient. This report delves into recent advancements within the CFD code NekRS, specifically those achieved in Fiscal Year 2024 under the CONNECT effort, aimed at improving the performance and feasibility of transient simulations. The first major advancement involves the porting of NekRS to Aurora, one of the Department of Energy’s (DOE) most powerful supercomputers. Additionally, the report discusses the implementation of an overlapping domain capability within NekRS. This novel GPU-accelerated capability allows different spatial regions of the domain to be solved independently, enhancing the code’s efficiency, particularly when running large-scale simulations in complex domains. The scalability of this approach is demonstrated, highlighting its potential to transform how transients are approached in CFD simulations. Lastly, the report focuses on how this overlapping domain capability specifically accelerates transient simulations through multi-rate timestepping. By decoupling different regions and facilitating faster computations, this method offers a promising pathway to making nuclear transient simulations more computationally feasible, addressing one of the critical bottlenecks in the field. Together, these advancements represent a significant leap forward in transient simulation technology, bringing closer the possibility of handling highly complex nuclear scenarios with greater efficiency and accuracy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1993

A concurrent hybrid Navier-Stokes/Euler approach to fluid dynamic computations

We present a methodology for the numerical simulation of flow fields by the simultaneous application of two distinct approaches to computational aerodynamics. We compute the three dimensional flow field of a missile at moderate angle of attack by dividing the flow field into two regions: a region near the surface where we use a structured grid and a Navier Stokes solver, and a region farther away from the surface where we utilize an unstructured grid and an Euler solver. The two solvers execute as independent UNIX processes either on the same machine or on two machines. The solvers communicate data across their common interfaces within the same machine or over the network. The computations indicate that extensively separated flow fields can be computed without significant distortion by combining viscous and inviscid solvers.

Tavella, Domingo A.↗

DOE OSTI2023

Terrain-Influenced Winds and Fire-Fire Interactions in Wildland Fire Simulations [Dissertation]

Ensemble-based approaches to prescribed fire planning cannot be supported by computational fluid dynamics based models like FIRETEC and the Wildland-Urban Interface Fire Dynamics Simulator (WFDS) because they are too computationally expensive and cannot leverage large eddy simulation approaches like CAWFE and WRF-SFIRE because they have too coarse of resolution. QUIC-Fire was developed to fill this gap but it cannot currently address complex terrain, that is typical for instance in the Western United States. This dissertation describes a variety of improvements made to QUIC-Fire and its various incorporated algorithms in an effort to make it a viable tool in simulating wildland and prescribed fires on terrain. The modifications made to QUIC-Fire are described in three chapters. The first chapter describes the extension of the diagnostic wind model QUIC-URB, the wind engine of QUIC-Fire, to a terrain-following coordinate system. The terraininfluenced winds it generates are analyzed and compared. In particular, this chapter presents the mathematical derivation of the wind solver leading to a linear system of equations that are solved through the successive over-relaxation method. The model is validated against a standard test used in previous works (the Askervein Hill) and against a new dataset from measurements in the Socorro Mountains, New Mexico. The terrain-following implementation captures the correct phenomenology for the isolated Askervein Hill, with a wind speed up at the top of the hill. The model agrees well with measurements on the upwind side of the peak, but overestimates speed-up on the downwind side of the hill. This is due to the inability of the model to generate flow separation and wake-eddy dynamics. On a common laptop, the divergence-free wind field is obtained in 6 s, making the solver appealing for coupled fire-atmosphere simulations. The Socorro Mountain is highly complex, with many cliff faces, peaks, and valleys. Although the model captures the magnitude and direction of inlet and outlet areas of the domain, it performs rather poorly in the valley region and in the regions near the steep cliffs. Hence, the model shows good agreement with data in areas of open sloped terrain but lacks in areas where flow separation and thermally driven effects may be present (neither effect is addressed in this work). In the second chapter the implementation of the terrain-following version of QUIC-URB into QUIC-Fire, and the necessary changes needed to include terrain are described. No changes to the underlying fire spread algorithm are made other than what is required to correctly account for the inclusion of terrain. Previously published FIRETEC results that use five different topographies that share the same centerline profile are compared to simulation results from the modified QUIC-Fire that use the same topographies and fuels. QUIC-Fire results show overall similar behaviors in terms of how the topographies affect fire shapes and trends in spread rates. Due to the terrain-following version of QUIC-URB being unable to generate flow separations at the crest of hills, fire spread rates in these regions across all topographies are over-predicted when compared to FIRETEC. Lateral fire growth shows similar trends with FIRETEC between topographies but does not capture the increase in spread due to a diagonal interface between grassland and forested fuel region of the domain. These results suggest that there are three algorithms within QUIC-Fire that could use improvement: how flame tilt angle is accounted for, the incorporation of non-local drag effects, and the inclusion of the wake-eddy parameterizations that are used in QUIC-URB. Lastly, the third chapter describes a modification to the initial guess used for the calculation of the QUIC-URB mass-conserved wind solution during fire simulations. The modification is aimed at improving fire-fire interactions in QUIC-Fire simulations. The modification consists of using the solution from the previous timestep as the starting point for the calculation of the solution for the next timestep. Fire-fire interactions is greatly improved by the change but a new source of error is introduced. Due to how plumes are modelled in QUIC-Fire the new solution contains errors where gaps in the plume structure are present. However, these errors are mostly limited to the upper atmosphere, where they do not affect fire behavior at the surface, and their magnitude isn’t significant enough to discount the amount of new fire phenomenology now captured in QUIC-Fire with the change.

58 GEOSCIENCES↗

DOE OSTI2021

Berni Julian Alder, theoretical physicist and inventor of molecular dynamics, 1925–2020

Berni Julian Alder, one of the leading figures in the invention of molecular dynamics simulations used for a wide array of problems in physics and chemistry, died on September 7th, 2020. His career, spanning more than 65 years, transformed statistical mechanics, many body physics, the study of chemistry and the microscopic dynamics of fluids, by making atomistic computational simulation (in parallel with traditional theory and experiment) a new pathway to unexpected discoveries. Among his many honors, the CECAM prize, recognizing exceptional contributions to the simulation of the microscopic properties of matter is named for him. He was awarded the National Medal of Science by President Obama in 2008.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

Simulations for Planning of Liquid Hydrogen Spill Test

In order to better understand the complex pooling and vaporization of a liquid hydrogen spill, Sandia National Laboratories is conducting a highly instrumented, controlled experiment inside their Shock Tube Facility. Simulations were run before the experiment to help with the planning of experimental conditions, including sensor placement and cross wind velocity. This paper describes the modeling used in this planning process and its main conclusions. Sierra Suite’s Fuego, an in-house computational fluid dynamics code, was used to simulate a RANS model of a liquid hydrogen spill with five crosswind velocities: 0.45, 0.89, 1.34, 1.79, and 2.24 m/s. Two pool sizes were considered: a diameter of 0.85 m and a diameter of 1.7. A grid resolution study was completed on the smaller pool size with a 1.34 m/s crosswind. A comparison of the length and height of the plume of flammable hydrogen vaporizing from the pool shows that the plume becomes longer and remains closer to the ground with increasing wind speed. The plume reaches the top of the facility only in the 0.45 m/s case. From these results, we concluded that it will be best for the spacing and location of the concentration sensors to be reconfigured for each wind speed during the experiment.

08 HYDROGEN↗

NASA NTRS2000

Computational Investigation of the Aerodynamic Effects on Fluidic Thrust Vectoring

A computational investigation of the aerodynamic effects on fluidic thrust vectoring has been conducted. Three-dimensional simulations of a two-dimensional, convergent-divergent (2DCD) nozzle with fluidic injection for pitch vector control were run with the computational fluid dynamics code PAB using turbulence closure and linear Reynolds stress modeling. Simulations were computed with static freestream conditions (M=0.05) and at Mach numbers from M=0.3 to 1.2, with scheduled nozzle pressure ratios (from 3.6 to 7.2) and secondary to primary total pressure ratios of p(sub t,s)/p(sub t,p)=0.6 and 1.0. Results indicate that the freestream flow decreases vectoring performance and thrust efficiency compared with static (wind-off) conditions. The aerodynamic penalty to thrust vector angle ranged from 1.5 degrees at a nozzle pressure ratio of 6 with M=0.9 freestream conditions to 2.9 degrees at a nozzle pressure ratio of 5.2 with M=0.7 freestream conditions, compared to the same nozzle pressure ratios with static freestream conditions. The aerodynamic penalty to thrust ratio decreased from 4 percent to 0.8 percent as nozzle pressure ratio increased from 3.6 to 7.2. As expected, the freestream flow had little influence on discharge coefficient.

Deere, K. A.↗

DOE OSTI2023

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗

NASA NTRS2001

Aerothermal Analysis of the Project Fire II Afterbody Flow

Computational fluid dynamics (CFD) is used to simulate the wake flow and afterbody heating of the Project Fire II ballistic reentry to Earth at 11.4 km/sec. Laminar results are obtained over a portion of the trajectory between the initial heat pulse and peak afterbody heating. Although non-catalytic forebody convective heating results are in excellent agreement with previous computations, initial predictions of afterbody heating were about a factor of two below the experimental values. Further analysis suggests that significant catalysis may be occurring on the afterbody heat shield. Computations including finite-rate catalysis on the afterbody surface are in good agreement with the data over the early portion of the trajectory, but are conservative near the peak afterbody heating point, especially on the rear portion of the conical frustum. Further analysis of the flight data from Fire II shows that peak afterbody heating occurs before peak forebody heating, a result that contradicts computations and flight data from other entry vehicles. This result suggests that another mechanism, possibly pyrolysis, may be occurring during the later portion of the trajectory, resulting in less total heat transfer than the current predictions.

Wright, Michael J.↗

NASA NTRS2009

CFD Simulation on the J-2X Engine Exhaust in the Center-Body Diffuser and Spray Chamber at the B-2 Facility

A computational fluid dynamic (CFD) code is used to simulate the J-2X engine exhaust in the center-body diffuser and spray chamber at the Spacecraft Propulsion Facility (B-2). The CFD code is named as the space-time conservation element and solution element (CESE) Euler solver and is very robust at shock capturing. The CESE results are compared with independent analysis results obtained by using the National Combustion Code (NCC) and show excellent agreement.

Wang, Xiao-Yen↗

NASA NTRS1998

A Method for Generating Reduced-Order Linear Models of Multidimensional Supersonic Inlets

Simulation of high speed propulsion systems may be divided into two categories, nonlinear and linear. The nonlinear simulations are usually based on multidimensional computational fluid dynamics (CFD) methodologies and tend to provide high resolution results that show the fine detail of the flow. Consequently, these simulations are large, numerically intensive, and run much slower than real-time. ne linear simulations are usually based on large lumping techniques that are linearized about a steady-state operating condition. These simplistic models often run at or near real-time but do not always capture the detailed dynamics of the plant. Under a grant sponsored by the NASA Lewis Research Center, Cleveland, Ohio, a new method has been developed that can be used to generate improved linear models for control design from multidimensional steady-state CFD results. This CFD-based linear modeling technique provides a small perturbation model that can be used for control applications and real-time simulations. It is important to note the utility of the modeling procedure; all that is needed to obtain a linear model of the propulsion system is the geometry and steady-state operating conditions from a multidimensional CFD simulation or experiment. This research represents a beginning step in establishing a bridge between the controls discipline and the CFD discipline so that the control engineer is able to effectively use multidimensional CFD results in control system design and analysis.

Chicatelli, Amy↗

NASA NTRS1988

Three dimensional simulation of an underexpanded jet interacting with a supersonic cross flow

A new three-dimensional computational fluid dynamics (CFD) code has been developed to simulate the flow fields of an underexpanded jet transversely injected into supersonic air stream inside the combustors of ramjets and scramjets. The code employs an implicit finite volume, lower-upper (LU) time marching method to solve the complete three-dimensional Navier-Stokes equations in a fully-coupled and very efficient manner. Results clearly depict the flow characteristics, including the shock structure, separated flow regions around the injector, and the wake flow in the lee of the injector.

Yu, Sheng-Tao↗

DOE OSTI2024

Forest structural complexity and ignition pattern influence simulated prescribed fire effects

Background: Forest structural characteristics, the burning environment, and the choice of ignition pattern each influence prescribed fire behaviors and resulting fire effects; however, few studies examine the influences and interactions of these factors. Understanding how interactions among these drivers can influence prescribed fire behavior and effects is crucial for executing prescribed fires that can safely and effectively meet management objectives. To analyze the interactions between the fuels complex and ignition patterns, we used FIRETEC, a three-dimensional computational fluid dynamics fire behavior model, to simulate fire behavior and effects across a range of horizontal and vertical forest structural complexities. For each forest structure, we then simulated three different prescribed fires each with a unique ignition pattern: strip-head, dot, and alternating dot. Results: Forest structural complexity and ignition pattern affected the proportions of simulated crown scorch, consumption, and damage for prescribed fires in a dry, fire-prone ecosystem. Prescribed fires in forests with complex canopy structures resulted in increased crown consumption, scorch, and damage compared to less spatially complex forests. The choice of using a strip-head ignition pattern over either a dot or alternating-dot pattern increased the degree of crown foliage scorched and damaged, though did not affect the proportion of crown consumed. We found no evidence of an interaction between forest structural complexity and ignition pattern on canopy fuel consumption, scorch, or damage. Conclusions: We found that forest structure and ignition pattern, two powerful drivers of fire behavior that forest managers can readily account for or even manipulate, can be leveraged to influence fire behavior and the resultant fire effects of prescribed fire. These simulation findings have critical implications for how managers can plan and perform forest thinning and prescribed burn treatments to meet risk management or ecological objectives.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Visualization of post-detonation fireball flowfields and comparison to CFD modeling

Visualization of flow structures within post-detonation fireballs has been performed for benchmark validation of numerical simulations. Custom pressed PETN explosives with a 12-mm diameter hemispherical form factor were used to produce a spherically symmetric post-detonation flow with low soot yield. Hydroxyl-radical planar laser induce fluorescence (OH-PLIF) was employed to visualize the structure ranging from approximately 10 μs to 35 μs after shock breakout from the explosive pellet. Fireball simulations were performed using the HyBurn Computational Fluid Dynamics (CFD) package. Experimental OH-PLIF results were compared to synthetic OH-PLIF from post-processing of CFD simulations. From the comparison of experimental and synthetic OH-PLIF images, CFD is shown to replicate much of the flow structure observed in the experiments, revealing potential differences in turbulent length scales and OH kinetics. Furthermore, results provide significant advancement in experimental resolution of these harsh turbulent combustion environments and validate physical models thereof.

Detonator↗

NASA NTRSDate not supplied

Simulating Underexpanded Plumes in Martian and Lunar Environments

While the Loci/Chem Computational fluid dynamics (CFD) application has been validated and used extensively for simulating launch environments in atmospheric conditions, use of this tool for simulating supersonic plumes at much lower ambient pressure requires further validation. Simulations of underexpanded plumes have been performed using Loci/Chem at Martian pressure to predict several metrics for laminar, turbulent, and impinging plumes. The CFD results are compared with an experimental data set for low Reynolds number plumes at these conditions in order to evaluate the current capability of the Loci/Chem tool for these types of environments. The CFD validation results to date show reasonable agreement with the experimental data across all the metrics of interest for the configurations considered. The Loci/Chem-Boltzmann tool is a hybrid continuum/rarefied flow solver which extends modeling capabilities to very low-pressure environments such as those on the Moon. The Loci/Chem-Boltzmann solver uses a gradient-based continuum breakdown criterion to restrict solution of the computationally expensive Boltzmann equation to only a subset of the domain, while using the Navier-Stokes equations elsewhere. This CFD application is under active development, and current efforts toward establishing production ready capability for evaluating Lunar plume surface interactions are well under way. Initial simulations of an Apollo Lunar excursion module indicate that several regions of the flow require solving the Boltzmann equations due to extreme rarefaction. Early simulations are promising, indicating reasonable overall computational time for a full 3D human scale lander simulation.

Plume Surface Interaction↗

NASA NTRS2023

Simulations of Zero Boiloff, Densification, and Solidification in a Large-Scale Liquid Hydrogen Tank

The current research utilizes an Energy of Fluid (EOF) approach to develop a finite volume-based Computation Fluid Dynamic (CFD) model to create a benchmark simulation of the densification of liquid hydrogen (LH2) in an experimental Integrated Refrigeration and Storage (IRAS) tank at the Kennedy Space Center (KSC). The computational code will incorporate the FLUENT pressure-based model with User Defined Functions (UDF) to implement the EOF model. The enhanced model will solve the energy equation in terms of internal energy and provide temperature and pressure calculations for a given tank geometry. Specifically, a convection term will be added to an already existing code for a more accurate simulation of LH2 densification. However, currently the research focuses on utilizing User Defined Scalars (UDS) with FLUENT to show the built-in solvers are as accurate as the written UDS. This will reduce the computational time down significantly by utilizing an already built in solver for the momentum equation. A custom UDF has been written to solve transient and steady state conduction, and results obtained using the UDF agree with results obtained using the built-in FLUENT solver. Currently, a convection UDF is being added and will be verified using known solutions for solidification and validated with the experimental results from the Cryogenics Test Laboratory (CTL) at KSC for the IRAS densification process.

Colin Philip Mahony↗