Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “bulk techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Significant improvement of conversion efficiency by passivation of low-angle grain boundaries in flexible low-cost single-crystal-like GaAs thin-film solar cells directly deposited on metal tape

We develop an easily implementable yet effective process to achieve high power conversion efficiency in newly-developed flexible single-crystal-like GaAs thin-film photovoltaic solar cells on cheap metal tape. We study various techniques on the fabricated devices to passivate the defect states associated with dangling bonds at low-angle grain boundaries (LA-GBs) existing in the single-crystal-like GaAs material. We report that sulfur by trioctylphosphine sulfide (TOP:S) solution treatment can partially but effectively passivate the defect states at the LA-GBs to increase all the solar cell performance parameters of open-circuit voltage VOC (33.2%), short-circuit current JSC (19.5%), and fill factor FF (25.8%), resulting in the improvement of the power conversion efficiency more than double. The material and device characterizations and numerical modeling are performed to propose a mechanism, also suggesting that the power conversion efficiency higher than 20%, which is an important target milestone in emerging solar cell technologies, can be achieved. This work presents the first effective passivation of the bulk defects in GaAs at the device level and can also offer a solution for other photonic and electronic devices using non-single-crystalline GaAs films for flexible electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sub-Alfvénic Turbulence: Magnetic-to-kinetic Energy Ratio, Modification of Weak Cascade, and Implications for Magnetic Field Strength Measurements

Abstract We study the properties of sub-Alfvénic magnetohydrodynamic (MHD) turbulence, i.e., turbulence with Alfvén mach number M A = V L / V A < 1, where V L is the velocity at the injection scale and V A is the Alfvén velocity. We demonstrate that MHD turbulence can have different properties, depending on whether it is driven by velocity or magnetic fluctuations. If the turbulence is driven by isotropic bulk forces acting upon the fluid, i.e., is velocity driven, in an incompressible conducting fluid we predict that the kinetic energy is M A − 2 times larger than the energy of magnetic fluctuations. This effect arises from the long parallel wavelength tail of the forcing, which excites modes with k ∥ / k ⊥ < M A . We also predict that as the MHD turbulent cascade reaches the strong regime, the energy of slow modes exceeds the energy of Alfvén modes by a factor M A − 1 . These effects are absent if the turbulence is driven through magnetic fluctuations at the injection scale. We confirm our predictions with numerical simulations. Since the assumption of magnetic and kinetic energy equipartition is at the core of the Davis–Chandrasekhar–Fermi (DCF) approach to measuring magnetic field strength in sub-Alfvénic turbulence, we conclude that the DCF technique is not universally applicable. In particular, we suggest that the dynamical excitation of long azimuthal wavelength modes in the galactic disk may compromise the use of the DCF technique. We discuss alternative expressions that can be used to obtain magnetic field strength from observations and consider ways of distinguishing the cases of velocity and magnetically driven turbulence using observational data.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Advancing Aerosol Chemical Characterization and Vertical Profiling over the Southern Great Plains Using Uncrewed Aerial Sampling and Offline Aerosol Mass Spectrometry

Recent advancements in uncrewed aerial systems (UASs) and particulate matter (PM) analytical techniques have provided opportunities for atmospheric research. In this study, we deployed the Department of Energy’s fixed-wing ArcticShark UAS to examine PM 2.5 composition at varying altitudes─within and above the planetary boundary layer (PBL)─over the Southern Great Plains atmospheric observatory (SGP). A total of 22 flights were conducted across March, June, and August 2023. Composite filter samples were collected during each flight and analyzed with offline aerosol mass spectrometry (AMS), complemented by on-board real-time sensors and ground-based instrumentation, to provide a comprehensive view of regional aerosol characteristics. Results show clear vertical and seasonal differences in the aerosol composition. Relative to ground-level measurements, aloft samples exhibited shifts in the distribution of organic and inorganic PM, with the organic composition varying distinctly across seasons. Particulate organic nitrogen (ON) was elevated, with bulk compositions similar in March and June but strongly altered in August, likely driven by biomass burning and enhanced photochemical activity. Combined AMS and chemical ionization mass spectrometry analyses detected amines, amides, and amino acids. PM above the planetary boundary layer was enriched in oxidized organic aerosols, while ground-level PM contained higher nitrate and sulfate. Seasonal differences in aqueous-phase processing were also observed, which were strongest in March during persistent cloud cover and weaker in the drier August period, suggesting a shift from aqueous- to gas-phase SOA formation. In conclusion, these findings highlight the value of UAS in advancing PM measurements and vertical profiling of aerosol composition.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

General Analysis of Data Collected from DOE Lidar Buoy Deployments Off Virginia and New Jersey

Pacific Northwest National Laboratory (PNNL) operates two AXYS WindSentinel lidar buoys for the U.S. Department of Energy’s Wind Energy Technologies. The purpose of these buoys is to collect hub-height winds and supporting meteorological and oceanographic information to facilitate the development of offshore wind energy in the U.S. In general, each buoy is deployed for a year or more at a given location in order to capture at least a full annual cycle of weather conditions. The initial deployment for one buoy was off the coast of Virginia beginning in 2015, and the other buoy was first deployed off the coast of New Jersey beginning in 2016. Over the last two years, PNNL has had an opportunity to analyze the data collected during these first two deployments. This report describes a substantial analysis of data collected by the two lidar buoys operated off the coasts of Virginia and New Jersey. The centerpiece instrument for each buoy as deployed off Virginia and New Jersey is a lidar system, which is designed to measure the horizontal wind vector from approximately 40 m to 200 m above the sea surface with vertical resolution of 40 m. Since the initial deployments, the original lidars have been replaced with more powerful Leosphere 866 v2 systems. The analyses in this report will apply to the original Vindicator systems. In addition to the wind profiles from the lidars, the buoys collect near-surface measurements of wind speed and direction, air temperature, relative humidity, barometric pressure, and solar irradiance. Oceanographic variables measured include the two-dimensional wave spectrum, water temperature and conductivity, and ocean current vectors to a depth of 90 m. An assessment of overall data recovery and a basic analysis of the data collected was provided in a previous report This report substantially extends that analysis. The various sections describe the development and application of an inertial measurement unit (IMU) data recovery scheme for the New Jersey deployment; a climatological analysis of winds at hub height and at the surface together with thermodynamic variables measured at the surface for the full deployment periods; an analysis of oceanographic observations describe sea state; the development of a refinement for NOAA’s WaveWatch III model to allow its application to near-shore areas; a basic climatology of ocean currents observed from the buoys; an analysis of observed winds in the framework of Monin-Obukhov Similarity Theory; and the development and evaluation of techniques to extract turbulence intensity and turbulence kinetic energy from the lidars. The analyses contained in this report provide a great deal of new information about offshore conditions on the U.S. East Coast. In addition, the experience gained will inform both configurations and analysis of data from future deployments of these lidar buoy systems.

17 WIND ENERGY↗
DOE OSTI2023

Subsurface Characteristics of Metal-Halide Perovskites Polished by an Argon Ion Beam

Focused ion beam (FIB) techniques have been frequently used to section metal-halide perovskites for microstructural investigations. However, the ion beams directly irradiating the sample surface may alter its properties far different from those of pristine, potentially leading to modified deterioration mechanisms under aging stressors. Here, we combine complementary approaches to measure the subsurface characteristics of polished perovskites and identify the chemical species responsible for the measured properties. Analysis of the experimental results in conjunction with Monte Carlo simulations indicates that atomic displacements and local heating occur in the first ≈15 nm of the subsurface of methylammonium lead iodide (MAPbI 3 ) by glancing-angle Ar + beam irradiation (4 kV at 3°). The lead-rich, iodine-deficient surface promotes rapid phase segregation under thermal aging conditions. On the other hand, despite the subsurface modification, our experiments confirm that the rest of the MAPbI 3 bulk retains the material integrity. Our observation supports that polished perovskites could serve in studying the properties of bulk or buried junctions far away from the altered subsurface with care.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Correlated Signal Analysis for Nuclear Emergency Response

In the context of nuclear emergency response (NER) scenarios, the critical task is to quickly identify a "black box" as a potential threat, as failing to do so could have catastrophic consequences. Techniques for passive assay of a “black box” typically include gamma-ray spectroscopy and neutron coincidence/multiplicity counting. However, there are significant challenges associated with these type of measurements. First, the presence of intervening materials can obstruct the detection of relevant signatures. Second, the presence of strong non-fission neutron sources, like (α, n) emitters, can add uncertainties to the neutron multiplicity analysis. In our LDRD-MFR Phase II work, a portable neutron spectrometer, called the Compact Fast Neutron Spectrometer (CFNS), was developed for NER applications. The CFNS system leverages information-rich neutron energy spectra to derive actionable information. This work investigates the use of correlated signals in the CFNS from special nuclear material (SNM) to characterize physical properties, such as intervening shielding material and fission to non-fission neutron contributions. In this report, the Phase II results from bulk SNM measurements at the National Criticality Experiments Research Center (NCERC) are briefly discussed along with the motivation for this work. Afterwards, simulations using the MCNPX-PoliMi transport code are discussed, which were used to expand our correlated signal study. Signal triggered analysis for neutron multiplicity extraction will also be discussed. Lastly, the use neutron-photon correlations for intervening material identification are shown, along with the use of correlated neutron energy spectra for α-ratio extraction.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Electric field stimulates production of highly conductive microbial OmcZ nanowires

Multifunctional living materials are attractive due to their powerful ability to self-repair and replicate. However, most natural materials lack electronic functionality. Here we show that an electric field, applied to electricity-producing Geobacter sulfurreducens biofilms, stimulates production of cytochrome OmcZ nanowires with 1,000-fold higher conductivity (30 S cm -1 ) and threefold higher stiffness (1.5 GPa) than the cytochrome OmcS nanowires that are important in natural environments. Using chemical imaging-based multimodal nanospectroscopy, we correlate protein structure with function and observe pH-induced conformational switching to β-sheets in individual nanowires, which increases their stiffness and conductivity by 100-fold due to enhanced π-stacking of heme groups; this was further confirmed by computational modeling and bulk spectroscopic studies. These nanowires can transduce mechanical and chemical stimuli into electrical signals to perform sensing, synthesis and energy production. Overall, these findings of biologically produced, highly conductive protein nanowires may help to guide the development of seamless, bidirectional interfaces between biological and electronic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Growth and Properties of Vapor Diffused Nb3Sn Coating for Superconducting Radiofrequency Accelerator Cavity Applications

The desire to reduce construction and operating costs of future SRF accelerators motivates the search for higher-performing alternative materials. Nb3Sn (Tc ~ 18.3 K and Hsh ~ 425 mT) is the front runner. The tin vapor diffusion process is currently the technique of choice to produce promising Nb3Sn-coated cavities. Understanding Nb3Sn nucleation and growth in this process is essential to progress. Samples representing different stages of Nb3Sn formation have been produced and studied to elucidate the effects of nucleation, growth, process conditions, and impurities. Nb3Sn films with thickness from a few hundred nm up to ~15 µm were grown and characterized. The microscopic examination of samples suggests the mechanisms of thin film nucleation and growth. Broadly, nucleation deposits tin as a thin surface phase and, under some conditions, a few hundred nanometer sized particles as well. Conditions that impair nucleation promote the formation of defects, such as ?patches?, in subsequent coating growth. Analysis of coated samples is consistent with the model of Nb3Sn grown in which tin diffuses via grain boundaries to Nb3Sn-Nb interface, where the growth Nb3Sn into the niobium bulk takes place. Similar scaling laws are found for grain growth and layer thickness. Non-parabolic layer growth is consistent with significant grain growth, which reduces the number of Sn-transport channels. Examination of patchy region in Nb3Sn coating revealed it to be large single crystalline grains, pointing to impeded Nb3Sn layer growth due to low grain boundary density, resulting in a significantly thin coating in those areas. Examination of RF loss regions from a coated cavity, identified with a thermometry mapping system showed patchy regions and carbonus defects were associated with strong local field-dependent surface resistance. RF measurements of coated cavities were combined with material characterization of witness samples and coated-cavity cutouts to improve the coating process. Understanding obtained and applied to cavity coatings, resulted in single-cell Nb3Sn cavities with a quality factor of ~2 ×1010 up to 15 MV/m accelerating gradient at 4 K, without "Wuppertal" Q-slope. We have also produced Nb3Sn-coated CEBAF 5-cell cavities with accelerating gradients useful for accelerator cryomodules. This dissertation will discuss the genesis of the Nb3Sn coating in a typical tin vapor diffusion process, effects of different process parameters, and its consequences to the coating of single-cell and multi-cell SRF cavities.

Pudasaini, Uttar↗
DOE OSTI2024

Tank Waste Characterization: History, Challenges, and Success Stories

The preparation and chemical and radiochemical analysis of Hanford tank waste samples can be performed with standard laboratory equipment and instruments as relatively routine processes that are not particularly challenging. Rather, the main challenges of tank waste characterization are associated with radiological dose and sampling limitations. Accurate, representative and effective sampling techniques are difficult with the waste tanks because they were not designed for routine sampling. There are a finite number of sampling locations for each tank based on riser positioning, depth and the operational functionality of the sampling riser. For example, in one recently emptied SST, there was one riser that was found to have had concrete dumped down it, thereby eliminating that sampling port. Additionally, the waste within the tank; especially true for the saltcake and sludge, is not homogenous. The ability to adequately mix a million-gallon double shell tank (DST) is a concern for data reproducibility. Another real challenge that must be addressed for sampling single shell tanks, is how to dissolve the salt cake waste in a compromised (leaking) SST. These physical constraints mean that uncertainty in the representativeness of samples must be considered when applying analytical results to the bulk contents of the tank. The tank waste is highly radioactive and thus can only be handled initially by facilities that can receive samples into concrete-shielded hot cells with remote operation with an example provided in Figure 1. The shielding protects the worker from the radiological dose while mineral oil windows and remotely operated manipulators enables the samples to be handled. At Hanford, analytical laboratories with these hot cell capabilities are limited to the Pacific Northwest National Laboratory and the main Hanford operations support laboratory, 222-S Laboratory. Because of their highly radioactive nature, samples must be sufficiently diluted to facilitate their analysis outside of a shielded cell. In some cases, this means some accuracy must be compromised to complete the analysis beyond that normally encountered for non-radioactive material.

Waste Characterization, BBI, PHOENIX: Tank Farms: ↗
DOE OSTI2025

Electrical Detection of Single-Domain Néel Vector Reorientation across the Spin–Flop Transition in Cr 2 O 3 Crystals

Electrical transport measurements in heterostructures of antiferromagnetic Cr 2 O 3 bulk crystals and a thin Pt layer exhibit sharp responses as the Néel vector of Cr 2 O 3 undergoes the spin−flop transition. This abrupt change can arise from several distinct mechanisms including magnetostriction, proximity-induced anomalous Hall, spin Hall anomalous Hall, and spin Hall planar Hall effects. While large Pt devices sensing multiple up/ down domains can produce indistinguishable Hall signal jumps due to different initial Néel vector orientations, smaller Pt devices that sense single domains isolate the proximity-induced Hall signals. This allows direct electrical detection of Néel vector reorientation across the spin−flop transition in single-domain regions. Furthermore, the single-domain state can be prepared by magnetic field cooling or magnetoelectric cooling. We demonstrate a method to control and characterize the three-dimensional orientation of single-domain Néel vectors by exploiting Hall measurements and cooling techniques, crucial for future antiferromagnetic spintronic applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Exploring constituent redistribution in irradiated U-19Pu-14Zr fuel via electron probe microanalysis

Here, the phenomena of constituent redistribution, wherein a previously homogeneous metallic fuel forms discrete, radially concentric compositional zones upon irradiation was investigated by examining an irradiated U-19Pu-14Zr fuel (where numbers represent wt. %) with a burnup of 11.5 at.% with electron probe microanalysis (EPMA) and quadruple inductively coupled plasma mass spectroscopy (Q-ICP-MS). EPMA-generated U, Pu, and Zr compositional data obtained from a diameter traverse of the sample was converted to mass and was used to: 1) compare the overall fuel element analysis results between the two methods, 2) determine the number of compositionally distinct zones forming as a result of constituent redistribution; and 3) quantify the post-irradiation loss or gain of U, Pu, and Zr atoms in each distinct compositional zone. Weight percent concentrations of U, Pu, and Zr for the overall cross section compare favorably between the two analytical methods, suggesting that the spatially resolved EPMA analysis complements bulk chemical analysis. Among the four identified compositional zones, post-irradiation quantification of U, Pu, and Zr elemental atom content changes shows that the quantity of U atoms lost from the innermost zone is slightly less than the quantity of U atoms gained by the middle two zones, and the quantity of Zr atoms lost from the high-U third zone is slightly less than is gained by the two innermost zones. Pu is lost from all four zones, although the innermost zone and the high-U third zone lose a significantly higher percentage (> 22 %) of their initial Pu atoms than the other two zones. For all three elements, EPMA cannot distinguish between atoms lost due to transport to a different zone from atoms lost due to nuclear processes; however, the insight gained from using this process can be used to experiment with new modeling techniques to predict constituent redistribution in U-Pu-Zr fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

An overview of switchgrass phenotypes variability across diverse populations and their implications for conversion to fuels

There have been substantial changes to the human lifestyle over the past two centuries, which are reflected in the amount of fuel we consume to power our day-to-day needs. The way we use these resources has indeed manifested in an overdependence on non-renewable energy sources, such as coal and petroleum, for generating electricity and powering our transportation needs. There is a pressing need to explore alternative ways of fueling our current lifestyle without impacting the environment. Biofuels have long been touted as a sustainable solution for use as drop-in fuels in aviation and maritime applications. Still, they have yet to establish themselves as a competitive commercial alternative, necessitating further research and development. Lignocellulosic biomass is an underutilized resource that is widely accessible for the commercial processing of renewable biofuels. Bioenergy crops, such as switchgrass (Panicum virgatum L.), which can be cultivated on marginal lands with minimal competition for agricultural land, are an ideal and promising candidate for bulk-scale biofuel synthesis. Over the past 30 years, significant progress has been made in breeding and genetically modifying these grasses to enhance their drought resilience and subsequent yields. However, discrepancies in biomass composition can lead to irregular feedstocks for downstream operations, which in turn affect overall production targets for biofuels. Here, this review examines the variability in switchgrass (P. virgatum L.) biomass phenotypes across diverse populations and plant components, and their implications for biofuel conversion. The study highlights significant variations in biomass yield, composition, and cell wall chemistry both between switchgrass genotypes and within individual cultivars. Key findings include differences in cellulose, hemicellulose, and lignin content between leaves and stems, which affect biomass digestibility and ethanol yield. The review also discusses the impact of lignin chemistry, particularly the syringyl/guaicyl (S/G) ratio, on the efficiency of biomass saccharification. Furthermore, it explores how these variations respond differently to various pretreatment techniques, affecting overall biofuel production. We conclude that understanding and quantifying this variability is crucial for optimizing switchgrass as a feedstock for commercial biofuel production, thereby potentially addressing the pressing need for sustainable energy sources in sectors such as aviation.

Kousika, Rohit [Univ. of Tennessee, Knoxville, TN ↗
DOE OSTI2025

Velocity-space signatures of shock-drift acceleration at quasi-perpendicular collisionless shocks

The shock-drift acceleration of ions at quasi-perpendicular shocks is a well-known kinetic mechanism for the acceleration of a small fraction of incoming ions to high energy. Here, we use a suite of sixteen hybrid simulations of quasi-perpendicular collisionless shocks over the range of Alfvén Mach number 4.3 ≤ M A ≤ 15.8 (corresponding to a range of fast magnetosonic Mach numbers 2.6 ≤ M f ≤ 9.4) and shock-normal angle 45°≤ θ Bn ≤ 90° to identify the velocity-space signature of shock-drift acceleration using the field-particle correlation technique. We show that the features of the ion velocity distribution in the shock foot and ramp regions can be clearly interpreted by analysis of the single-particle trajectory of a reflected ion through the full 3D-3V phase space. The characteristic features of the velocity-space signature of shock-drift acceleration remain qualitatively robust over the full parameter range of our simulations, providing a potential means for its identification using single-point spacecraft measurements. At higher Alfvén Mach numbers M A ≳8 (M f ≳5), kinetic instabilities generate fluctuations of the electromagnetic fields within the shock transition region, leading to fluctuations in and smearing out of the resulting velocity-space signatures, but the signature remains generally robust and identifiable. The results on the shock-drift acceleration of ions presented here represent a novel means to determine more completely the partitioning of upstream bulk flow kinetic energy into plasma heating, particle acceleration, and electromagnetic fields in collisionless shocks.

Howes, Gregory G. [Univ. of Iowa, Iowa City, IA (U↗
DOE OSTI2025

In situ high-temperature Raman spectroscopy for online EAF slag analysis

Real-time monitoring of slag chemistry is critical for optimizing Electric Arc Furnace (EAF) steelmaking operations, where dynamic variations in slag composition directly influence slag foaming, refractory degradation, and thermal efficiency. Conventional techniques such as X-ray fluorescence (XRF), Fourier-transform infrared (FTIR), and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) are commonly used to analyze slag composition, but their offline nature and equipment constraints limit their applicability for online monitoring in harsh industrial environments. To address this challenge, we present an in situ, high-temperature analytical approach that integrates Raman spectroscopy with a custom designed fiber-optic probe for real-time slag characterization at 1550 °C. The system enables non destructive spectral acquisition from molten slags, providing molecular-level insights into silicate polymerization and iron oxidation states. Eight synthetic slag samples were evaluated, and key Raman features—such as Q n silicate units and FeO₄/FeO₆ coordination environments—were identified and quantitatively correlated with slag basicity and Fe₂O₃ content. The results demonstrate agreement between Raman spectral ratios and bulk slag chemistry, validating the method’s capability to track compositional and structural changes under molten temperature. This work establishes the feasibility of deploying fiber-optic Raman probe for online EAF slag monitoring and highlights their potential to support closed-loop control strategies, thereby enhancing process stability, refractory protection, and steel quality in industrial steelmaking applications.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Detecting damage in composites using volume decomposition analysis of tomographic data

Detection of damage in a single tow ceramic matrix composite specimen has been achieved using orthogonal decomposition of volumetric tomographic datasets collected at four tensile loads. This decomposition approach has been applied at two different length scales: (i) individual fibres and (ii) bulk volumes containing fibres and matrix material. Volumes were first decomposed to feature vectors, orders of magnitude smaller than the original volume they describe, and then comparisons between datasets at different load levels were made in feature vector space. The results show quantitative measurements of damage location, damage morphology and the relative growth of this damage with increased load when compared with a dataset with less or no damage. No prior knowledge of the dataset or training of algorithms is required for damage to be detected, it is only necessary that at least two datasets are available for comparison, e.g. from in situ or repeated scanning measurements. Results are generated on significantly shorter timescales when compared with previous automated approaches to tomography data processing. This approach has the potential to be applied to damage detection in a range of materials through comparisons of volumetric datasets from a range of measurement or computational techniques.

Middleton, Ceri A.↗
DOE OSTI2024

Epoxy Coating of Biofiber: An Effective Modifier of Biofiber Physical and Flow Properties for Improved Tensile Behavior of Biofiber-Reinforced Biocomposite

Biocomposites combine renewable, plant-based fibers with degradable polymers and are an attractive option for sustainable, lightweight, and cost-effective materials with a low carbon footprint, especially for large-scale additive manufacturing. One of the major challenges in the widespread adoption of biocomposites is that their mechanical performance is significantly inferior to that of synthetic composites. Surface treatment is a common and effective technique to improve the mechanical properties of the biofibers used in biocomposites. This study aims to investigate the physical and flow properties of surface-treated biofibers, as well as the tensile properties of their PLA-based biocomposite, to gain insights into how surface treatment changes the fiber‘s characteristics and biocomposite‘s mechanical properties. Surface treatment was created using a two-component epoxy system by reacting poly(bisphenol A-co-epichlorohydrin) glycidyl end-capped (PBG) and dicyandiamide (DICY). The treatment was tested on two different biofibers (loblolly pine and corn stover fibers) with three different PBG/DICY molar ratios (0.25, 0.5, and 2). Results showed that surface-treated fibers improved the tensile strength and Young‘s modulus of the biocomposites. Loblolly pine biocomposites from fibers treated with a PBG/DICY ratio of 0.25 exhibited the best tensile properties. The surface treatment resulted in a more loosely dispersed fiber bulk structure, as evidenced by less fiber agglomeration into smaller particle sizes, higher fiber sphericity, and lower loose bulk density. This can enhance stress distribution and the overall mechanical performance of the biocomposites. Additionally, surface-treated fibers exhibited better dynamic flow properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Measurement of flow properties coupled to experimental and numerical analyses of dense, granular flows for solar thermal energy storage

Granular flows of sintered bauxite proppants were researched along an inclined plane for solar thermal energy storage applications. Granular flow properties needed to drive numeric granular models were measured for improved numerical model predictions for Carbobead CP 50/140, 40/100, and 30/60 particles. Particle shape and size distributions were determined by coupling optical microscopy to an in-house image processing algorithm. The impulse excitation technique was used to measure elastic and shear moduli, and compute Poisson’s ratio. The coefficient of static sliding friction was measured using the slip-stick method, and the static rolling friction was determined from measured shear on particles positioned between two hot-pressed plates. The coefficient of restitution was measured by dropping particles on a surface and determining the kinetic energy before and after impact with the surface using high resolution particle tracking velocimetry. Particle size did not significantly impact the coefficients of restitution and static rolling friction, however, particle shape distribution resulted in a large variation in measurements. An inclined flow experiment was performed to characterize granular flows of Carbobead CP 30/60 particles using particle image velocimetry. Numerical models of the experiment using discrete element method were generated with the measured mechanical properties as inputs for comparison with experimental results. A constant directional torque rolling friction model best predicted bulk granular flow behavior. Furthermore, good agreement between the model and experiment was achieved at ambient, steady state conditions, with average velocity differences <10%.

14 SOLAR ENERGY↗
DOE OSTI2026

Silyl Hot-Injection Versus Thiocyanate Heat-Up Synthesis of Chalcohalides: Pushing the Size and Composition Envelope

Chalcohalide semiconductors are rapidly gaining traction as stable, biocompatible materials for energy conversion applications. While the solid-state synthesis of bulk chalcohalides is relatively well-developed, the colloidal chemistry of these materials is still in its early stages. Colloidal semiconductors are often advantageous in device fabrication due to the cost effectiveness of solution processing. Thus, we aim to increase the utility of chalcohalides in device fabrication by establishing solution phase chemistry of promising compositions. We show that silyl hot-injection is a versatile and effective method of making colloidal PnChI (Pn = Sb, Bi; Ch = S, Se) and Sn 2 PnS 2 I 3 (Pn = Sb, Bi) chalcohalides of tunable sizes and compositions. Furthermore, we demonstrate the preparation of mixed-pnictide chalcohalides through direct hot-injection and/or postsynthetic cation exchange, the latter being one of the few reported instances in chalcohalides. Additionally, we use the thiocyanate heat-up approach in combination with density functional theory to study halide mixing in quaternary tin chalcohalides. By pushing the limits of each synthetic technique, we have designed more soluble chalcohalides with tunable compositions while also gaining a better understanding of the efficacy of each procedure in respect to thin film and subsequent device fabrication. In addition to size and composition tuning, silyl hot-injection can help facilitate the future development and wide-scale application of chalcohalide-based devices by expanding the selection of solution-processable chalcohalides.

halogens↗