Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

An investigation of the effects of the propeller slipstream of a laminar wing boundary layer

A research program is in progress to study the effects of the propeller slipstream on natural laminar flow. Flight and wind tunnel measurements of the wing boundary layer have been made using hot-film velocity sensor probes. The results show the boundary layer, at any given point, to alternate between laminar and turbulent states. This cyclic behavior is due to periodic external flow turbulence originating from the viscous wake of the propeller blades. Analytic studies show the cyclic laminar/turbulent boundary layer to result in a significantly lower wing section drag than a fully turbulent boundary layer. The application of natural laminar flow design philosophy yields drag reduction benefits in the slipstream affected regions of the airframe, as well as the unaffected regions.

Howard, R. M.↗
NASA NTRS2011

Off-Body Boundary-Layer Measurement Techniques Development for Supersonic Low-Disturbance Flows

Investigations were performed to develop accurate boundary-layer measurement techniques in a Mach 3.5 laminar boundary layer on a 7 half-angle cone at 0 angle of attack. A discussion of the measurement challenges is presented as well as how each was addressed. A computational study was performed to minimize the probe aerodynamic interference effects resulting in improved pitot and hot-wire probe designs. Probe calibration and positioning processes were also developed with the goal of reducing the measurement uncertainties from 10% levels to less than 5% levels. Efforts were made to define the experimental boundary conditions for the cone flow so comparisons could be made with a set of companion computational simulations. The development status of the mean and dynamic boundary-layer flow measurements for a nominally sharp cone in a low-disturbance supersonic flow is presented.

Owens, Lewis R.↗
NASA NTRS1991

Effect of leading-edge geometry on boundary-layer receptivity to freestream sound

The receptivity to freestream sound of the laminar boundary layer over a semi-infinite flat plate with an elliptic leading edge is simulated numerically. The incompressible flow past the flat plate is computed by solving the full Navier-Stokes equations in general curvilinear coordinates. A finite-difference method which is second-order accurate in space and time is used. Spatial and temporal developments of the Tollmien-Schlichting wave in the boundary layer, due to small-amplitude time-harmonic oscillations of the freestream velocity that closely simulate a sound wave travelling parallel to the plate, are observed. The effect of leading-edge curvature is studied by varying the aspect ratio of the ellipse. The boundary layer over the flat plate with a sharper leading edge is found to be less receptive. The relative contribution of the discontinuity in curvature at the ellipse-flat-plate juncture to receptivity is investigated by smoothing the juncture with a polynomial. Continuous curvature leads to less receptivity. A new geometry of the leading edge, a modified super ellipse, which provides continuous curvature at the juncture with the flat plate, is used to study the effect of continuous curvature and inherent pressure gradient on receptivity.

Lin, Nay↗
NASA NTRS1983

Developing mass spectrometric techniques for boundary layer measurement in hypersonic high enthalpy test facilities

Thermodynamic flow properties of gases in the boundary layer or the flowfield have been mainly deduced from pressures and temperatures measured on a model. However, further progress with respect to an understanding of these properties requires a more complete characterization of the layer including determination of the gas composition and chemistry. Most attempts to measure boundary layer chemistry involve the employment of a mass spectrometer and an associated gas sampling system. The three major limiting factors which must be addressed for species measurement in aerothermodynamic investigations on models at reentry stream velocities, are gas sampling effects, instrument limitations, and problems with data acquisition. The present investigation is concerned with a concentrated effort to quantitatively identify and correct for instrument and sampling system effects, and to develop a miniaturized high performance mass spectrometer for on-model real-time analysis of the boundary layer and its associated atmosphere.

Wood, G. M., Jr.↗
NASA NTRS1984

Stability of the laminar boundary layer in a streamwise corner

The stability of viscous, incompressible flow along a streamwise corner, often called the corner boundary layer problem is examined. The semi-infinite boundary value problem satisfied by small amplitude disturbances in the "bending boundary layer' region is obtained. The mean secondary flow induced by the corner exhibits a flow reversal in this region. Uniformly valid "first approximations' to solutions of the governing differential equations are derived. Uniformity at infinity is achieved by a suitable choice of the large parameter and use of an approximate Langer variable. Approximations to solutions of balanced type have a phase shift across the critical layer which is associated with instabilities in the case of two dimensional boundary layer profiles.

Lakin, W. D.↗
NASA NTRS1984

Stability of the laminar boundary layer in a streamwise corner

The stability of viscous, incompressible flow along a streamwise corner, often called the corner boundary layer problem is examined. The semi-infinite boundary value problem satisfied by small amplitude disturbances in the 'bending boundary layer' region is obtained. The mean secondary flow induced by the corner exhibits a flow reversal in this region. Uniformly valid 'first approximations' to solutions of the governing differential equations are derived. Uniformity at infinity is achieved by a suitable choice of the large parameter and use of an approximate Langer variable. Approximations to solutions of balanced type have a phase shift across the critical layer which is associated with instabilities in the case of two dimensional boundary layer profiles. Previously announced in STAR as N84-17532

Lakin, W. D.↗
NASA NTRS1991

Exploratory study of in-plane streamline curvature effects on a turbulent boundary layer at a Mach number of 3

This report on a program to study in-plane streamline curvature effects in a turbulent boundary layer at a Mach number of 3. The original proposal, for a 3-year program to explore in-plane streamline curvature effects on a supersonic turbulent boundary layer using three-dimensional pressure fields generated by fins and wall geometry, ended after one year. The purpose of these tests was to compare these streamline curvature effects to the more classical two-dimensional curvature generated by wall shape and imposed pressure gradients, previously considered primarily in a plane normal to the floor. The studies were carried out in the Mach number of 3, 8 x 8 inch High Reynolds Number Supersonic Tunnel. The usual surface visualization and mean wall static pressures were supplemented by the use of many small high frequency wall static pressure gauges (Kulites) to get some indication of the amplification of boundary layer disturbances by the in-plane streamline curvature caused by the three-dimensional pressure fields imposed on the boundary layer.

Bogdonoff, Seymour M.↗
NASA NTRS1982

Recent sidewall boundary-layer investigations with suction in the Langley 0.3-m Transonic Cryogenic Tunnel

An experimental and theoretical study of the Langley 0.3-m Transonic Cryogenic Tunnel (TCT) sidewall boundary-layer with and without suction, has been made. Without suction, the boundary-layer displacement thickness at a station ahead of the model varied from about 1.6 mm to 1.3 mm over a Reynolds number range of 20 million to 200 million per m at Mach numbers from 0.30 to 0.76. Measured velocity profiles were correlated using the defect law of Hama. The boundary-layer displacement thickness decreased when suction was applied; however, after suction of about 2 percent of test section mass flow, the change in the thickness was small. A comparison of the measured suction effectiveness with finite difference and integral methods of boundary-layer calculation showed that both methods predicted the right trend over the range of suction velocities (up to a suction to free-stream velocity ratio of -0.02).

Murthy, A. V.↗
NASA NTRS1995

Direct Simulation of Evolution and Control of Three-Dimensional Instabilities in Attachment-Line Boundary Layers

The spatial evolution of three-dimensional disturbances in an attachment-line boundary layer is computed by direct numerical simulation of the unsteady, incompressible Navier-Stokes equations. Disturbances are introduced into the boundary layer by harmonic sources that involve unsteady suction and blowing through the wall. Various harmonic- source generators are implemented on or near the attachment line, and the disturbance evolutions are compared. Previous two-dimensional simulation results and nonparallel theory are compared with the present results. The three-dimensional simulation results for disturbances with quasi-two-dimensional features indicate growth rates of only a few percent larger than pure two-dimensional results; however, the results are close enough to enable the use of the more computationally efficient, two-dimensional approach. However, true three-dimensional disturbances are more likely in practice and are more stable than two-dimensional disturbances. Disturbances generated off (but near) the attachment line spread both away from and toward the attachment line as they evolve. The evolution pattern is comparable to wave packets in at-plate boundary-layer flows. Suction stabilizes the quasi-two-dimensional attachment-line instabilities, and blowing destabilizes these instabilities; these results qualitatively agree with the theory. Furthermore, suction stabilizes the disturbances that develop off the attachment line. Clearly, disturbances that are generated near the attachment line can supply energy to attachment-line instabilities, but suction can be used to stabilize these instabilities.

Joslin, Ronald D.↗
DOE OSTI2024

Statistically Resolved Planetary Boundary Layer Height Diurnal Variability Using Spaceborne Lidar Data

The Planetary Boundary Layer Height (PBLH) significantly impacts weather, climate, and air quality. Understanding the global diurnal variation of the PBLH is particularly challenging due to the necessity of extensive observations and suitable retrieval algorithms that can adapt to diverse thermodynamic and dynamic conditions. This study utilized data from the Cloud-Aerosol Transport System (CATS) to analyze the diurnal variation of PBLH in both continental and marine regions. By leveraging CATS data and a modified version of the Different Thermo-Dynamics Stability (DTDS) algorithm, along with machine learning denoising, the study determined the diurnal variation of the PBLH in continental mid-latitude and marine regions. The CATS DTDS-PBLH closely matches ground-based lidar and radiosonde measurements at the continental sites, with correlation coefficients above 0.6 and well-aligned diurnal variability, although slightly overestimated at nighttime. In contrast, PBLH at the marine site was consistently overestimated due to the viewing geometry of CATS and complex cloud structures. The study emphasizes the importance of integrating meteorological data with lidar signals for accurate and robust PBLH estimations, which are essential for effective boundary layer assessment from satellite observations.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1996

Nonlinear Excitation of Inviscid Stationary Vortex in a Boundary-Layer Flow

We examine the excitation of inviscid stationary crossflow instabilities near an isolated surface hump (or indentation) underneath a three-dimensional boundary layer. As the hump height (or indentation depth) is increased from zero, the receptivity process becomes nonlinear even before the stability characteristics of the boundary layer are modified to a significant extent. This behavior contrasts sharply with earlier findings on the excitation of the lower branch Tollmien-Schlichting modes and is attributed to the inviscid nature of the crossflow modes, which leads to a decoupling between the regions of receptivity and stability. As a result of this decoupling, similarity transformations exist that allow the nonlinear receptivity of a general three-dimensional boundary layer to be studied with a set of canonical solutions to the viscous sublayer equations. The parametric study suggests that the receptivity is likely to become nonlinear even before the hump height becomes large enough for flow reversal to occur in the canonical solution. We also find that the receptivity to surface humps increases more rapidly as the hump height increases than is predicted by linear theory. On the other hand, receptivity near surface indentations is generally smaller in comparison with the linear approximation. Extension of the work to crossflow receptivity in compressible boundary layers and to Gortler vortex excitation is also discussed.

Choudhari, Meelan↗
NASA NTRS1991

On the X-ray emitting boundary layer of the dwarf nova VW Hydri

The temperature and luminosity of the boundary layer of VW Hyi are constrained to kT(BL) of about 10.5 eV, and L(BL) of about 6 x 10 to the 32nd (d/65 pc)squared ergs/sec. This is based on Voyager far- and extreme-ultraviolet spectrophotometry and a measurement of the column density of neutral hydrogen, combined with Exosat LE filter observations. Results are compared with the accretion-disk luminosity found by Polidan et al. (1990) using concurrent optical, IUE, and Voyager spectrophotometric observations. The value of zeta is found to be about 0.04, although theoretical predictions show comparable luminosities at the boundary layer and the accretion disk - zeta is identical to L(BL)/L(disk), which is about 1 - unless the white dwarf rotates very rapidly. Severe contamination of filter observations due to light from the inner accretion disk is also found. This contamination had previously been understood as a result of the luminous ultrasoft boundary layer.

Mauche, Christopher W.↗
NASA NTRS1989

Sidewall boundary-layer removal effects on wall adaptation in the Langley 0.3-meter transonic cryogenic tunnel

This paper describes the Langley 0.3-m transonic cryogenic tunnel sidewall boundary-layer removal system and is integrated operation with the adaptive wall adjustment. Empty test section measurements show the sidewall boundary-layer displacement thickness at the model station is reduced from about 1.0 to 0.6 percent of the test section width when the maximum boundary-layer removal conditions are applied. Tests with a supercritical airfoil model show the iterative top and bottom wall adaptation process performs satisfactorily with sidewall boundary-layer removal.

Murthy, A. V.↗
NASA NTRS1985

An experimental and computational study of turbulent boundary layers in oscillating flows

An experimental-computational study of the behavior of turbulent boundary layers for oscillating air flows over a plane surface with a small favorable mean pressure gradient is described. Experimental data were obtained for boundary layers generated on the test section wall of a new type of facility that produces a mean flow velocity with a superposed sinusoidal component over a wide frequency range. Experimental results for unsteady velocity profiles and turbulence intensity obtained from hot wire measurements at a fixed stream-wise position on the surface are presented for frequencies ranging from 5 to 21 Hz. Numerical predictions were obtained using an unsteady boundary layer computational code and the Cebeci-Smith and Glushko turbulence models. Predicted quantities related to unsteady velocity profiles exhibit fair agreement with experiment when the Cebeci-Smith model is used.

Cook, W. J.↗
NASA NTRS1991

Modeling of the heat transfer in bypass transitional boundary-layer flows

A low Reynolds number k-epsilon turbulence model and conditioned momentum, energy and turbulence equations were used to predict bypass transition heat transfer on a flat plate in a high-disturbance environment with zero pressure gradient. The use of conditioned equations was demonstrated to be an improvement over the use of the global-time-averaged equations for the calculation of velocity profiles and turbulence intensity profiles in the transition region of a boundary layer. The approach of conditioned equations is extended to include heat transfer and a modeling of transition events is used to predict transition onset and the extent of transition on a flat plate. The events, which describe the boundary layer at the leading edge, result in boundary-layer regions consisting of: (1) the laminar, (2) pseudolaminar, (3) transitional, and (4) turbulent boundary layers. The modeled transition events were incorporated into the TEXSTAN 2-D boundary-layer code which is used to numerically predict the heat transfer. The numerical predictions in general compared well with the experimental data and revealed areas where additional experimental information is needed.

Simon, Frederick F.↗
NASA NTRS1974

Boundary layer separation and reattachment

A review of developments in a new model for boundary-layer separation is presented. The separation model encompasses timevarying as well as steady-flow conditions. Engineering criteria in terms of calculable pressure gradients are obtained for both laminar and turbulent boundary-layer separation. These criteria, together with limited information on time-dependent separations, should be of value in predicting flows in turbomachinery. The reattachment of boundary layers is also shown to fit within the separation model.

Sandborn, V. A.↗
NASA NTRS1978

The analysis of a nonsimilar laminar boundary layer

A computer code is described which yields accurate solutions for a broad range of laminar, nonsimilar boundary layers, providing the inviscid flow field is known. The boundary layer may be subject to mass injection for perfect-gas, nonreacting flows. If no mass injection is present, the code can be used with either perfect-gas or real-gas thermodynamic models. Solutions, ranging from two-dimensional similarity solutions to solutions for the boundary layer on the Space Shuttle Orbiter during reentry conditions, have been obtained with the code. Comparisons of these solutions, and others, with solutions presented in the literature; and with solutions obtained from other codes, demonstrate the accuracy of the present code.

Stalmach, D. D.↗