Results for “active solids” — Page 46

NASA NTRS1974

Domestic wash water reclamation for reuse as commode water supply using filtration: Reverse-osmosis separation technique

A combined filtration-reverse-osmosis water recovery system has been evaluated to determine its capability to reclaim domestic wash water for reuse as a commode water supply. The system produced water that met all chemical and physical requirements established by the U.S. Public Health Service for drinking water with the exception of carbon chloroform extractables, methylene blue active substances, and phenols. It is thought that this water is of sufficient quality to be reused as commode supply water. The feasibility of using a combined filtration and reverse-osmosis technique for reclaiming domestic wash water has been established. The use of such a technique for wash-water recovery will require a maintenance filter to remove solid materials including those less than 1 micron in size from the wash water. The reverse-osmosis module, if sufficiently protected from plugging, is an attractive low-energy technique for removing contaminants from domestic wash water.

Hall, J. B., Jr.↗

NASA NTRS1988

The determination of energy transfer rates in the Ho:Tm:Cr:YAG laser material

Energy transfer processes occurring between atomic, ionic, or molecular systems are very widespread in nature. The applications of such processes range form radiation physics and chemistry to biology. In the field of laser physics, energy transfer processes have been used to extend the lasing range, increase the output efficiency, and influence the spectral and temporal characteristics of the output pulses of energy transfer dye lasers or solid-state laser materials. Thus in the development of solid state lasers, it is important to investigate the basic energy transfer (ET) mechanisms and processes in order to gain detailed knowledge so that successful technical utilization can be achieved. The aim of the present research is to measure the ET rate from a given manifold associated with the chromium sensitizer atom to a given manifold in the holmium activator atom via the thulium transfer atom, in the Ho:Cr:YAG laser material.

Koker, Edmond B.↗

NASA NTRS1996

Dynamics of Permanent-Magnet Biased Active Magnetic Bearings

Active magnetic radial bearings are constructed with a combination of permanent magnets to provide bias forces and electromagnets to generate control forces for the reduction of cost and the operating energy consumption. Ring-shaped permanent magnets with axial magnetization are attached to a shaft and share their magnet stators with the electromagnets. The magnet cores are made of solid iron for simplicity. A simplified magnetic circuit of the combined magnet system is analyzed with linear circuit theory by approximating the characteristics of permanent magnets with a linear relation. A linearized dynamical model of the control force is presented with the first-order approximation of the effects of eddy currents. Frequency responses of the rotor motion to disturbance inputs and the motion for impulsive forces are tested in the non-rotating state. The frequency responses are compared with numerical results. The decay of rotor speed due to magnetic braking is examined. The experimental results and the presented linearized model are similar to those of the all-electromagnetic design.

Fukata, Satoru↗

NASA NTRS1998

Status of Regenerative Life Support Research and Technology Program at NASA Ames Research Center

Future long duration manned space missions will require life support systems that minimize resupply requirements and ultimately approach self-sufficiency in space. This presentation will provide an overview of the Advanced Life Support program unclassified fundamental research and technology development activities being conducted at NASA Ames Research Center. Top level program goals and technical objectives, and the role of NASA-Ames within the Advanced Life Support program, will be reviewed. The presentation will focus on FY97 and FY98 research tasks that were directed at physicochemical processes with emphasis on system closure and self-sufficiency. Research areas include solid waste processing and resource recovery, water recycling, air regeneration, and regenerative system dynamics. Proposed future work and potential applications of this research to both terrestrial and space closed ecology experimentation in space will be addressed.

Kliss, Mark↗

NASA NTRS2010

Lessons Learned in Launching Ares I-X

The Ares I-X flight test, scheduled for 2009, is the first opportunity for the Constellation Program and Ares Projects to obtain important data on the in-flight loads, first stage recovery, and ground-handling characteristics of the Ares I crew launch vehicle. The flight test vehicle will incorporate a mix of flight and mockup hardware, reflecting an acceptable representation of the mass and outer mold line characteristics of the operational Ares I vehicle. It will be powered by a four-segment solid rocket motor from the Space Shuttle inventory and will include a fifth, inert spacer segment and new forward structures to make it the same shape as the Ares I first stage. The vehicle also includes mass simulators for the upper stage, Orion crew module, and launch abort system to match the outer mold line of Ares I; an active roll control system; and avionics derived from Shuttle and Atlas hardware. This suborbital mission will take the flight test vehicle from stacking in the Vehicle Assembly Building (VAB) at Kennedy Space Center (KSC) through liftoff, maximum dynamic pressure, first stage separation, and recovery. Ares I-X presented NASA with unique project management challenges. This presentation will address those unique challenges, including managing a virtual nationwide team under a constrained timeline; designing and building the launch vehicle and ground systems; working concurrently with Space Shuttle activities; and integrating technical and management functions. It also will identify key data collected and lessons learned from the flight that will be applied to future exploration missions.

Davis, Stephan R.↗

NASA NTRS2017

OSIRIS-REx Asterod Sample Return Mission

OSIRIS-REx is NASA's third New Frontiers Program mission, following New Horizons that completed a flyby of Pluto in 2015 and the Juno mission to Jupiter that has just begun science operations. The OSIRIS-REx mission's primary objective is to collect pristine surface samples of a carbonaceous asteroid and return to Earth for analysis. Carbonaceous asteroids and comets are 'primitive' bodies that preserved remnants of the Solar System starting materials and through their study scientists can learn about the origin and the earliest evolution of the Solar System. The OSIRIS-REx spacecraft was successfully launched on September 8, 2016, beginning its seven year journey to asteroid 101955 Bennu. The robotic arm will collect 60-2000 grams of material from the surface of Bennu and will return to Earth in 2023 for worldwide distribution by the Astromaterials Curation Facility at NASA Johnson Space Center. The name OSIRIS-REx embodies the mission objectives (1) Origins: Return and analyze a sample of a carbonaceous asteroid, (2) Spectral Interpretation: Provide ground-truth for remote observation of asteroids, (3) Resource Identification: Determine the mineral and chemical makeup of a near-Earth asteroid (4) Security: Measure the non-gravitational that changes asteroidal orbits and (5) Regolith Explorer: Determine the properties of the material covering an asteroid surface. Asteroid Bennu may preserve remnants of stardust, interstellar materials and the first solids to form in the Solar System and the molecular precursors to the origin of life and the Earth's oceans. Bennu is a potentially hazardous asteroid, with an approximately 1 in 2700 chance of impacting the Earth late in the 22nd century. OSIRIS-REx collects from Bennu will help formulate the types of operations and identify mission activities that astronauts will perform during their expeditions. Such information is crucial in preparing for humanity's next steps beyond low Earthy orbit and on to deep space destinations.

Nakamura-Messinger, Keiki↗

NASA NTRS2017

Simulation of Guided-Wave Ultrasound Propagation in Composite Laminates: Benchmark Comparisons of Numerical Codes and Experiment

Ultrasonic wave methods constitute the leading physical mechanism for nondestructive evaluation (NDE) and structural health monitoring (SHM) of solid composite materials, such as carbon fiber reinforced polymer (CFRP) laminates. Computational models of ultrasonic wave excitation, propagation, and scattering in CFRP composites can be extremely valuable in designing practicable NDE and SHM hardware, software, and methodologies that accomplish the desired accuracy, reliability, efficiency, and coverage. The development and application of ultrasonic simulation approaches for composite materials is an active area of research in the field of NDE. This paper presents comparisons of guided wave simulations for CFRP composites implemented using four different simulation codes: the commercial finite element modeling (FEM) packages ABAQUS, ANSYS, and COMSOL, and a custom code executing the Elastodynamic Finite Integration Technique (EFIT). Benchmark comparisons are made between the simulation tools and both experimental laser Doppler vibrometry data and theoretical dispersion curves. A pristine and a delamination type case (Teflon insert in the experimental specimen) is studied. A summary is given of the accuracy of simulation results and the respective computational performance of the four different simulation tools.

Composite↗

NASA NTRS2020

Area South of K7-516, SWMU 100 Operations, Maintenance, and Monitoring Report Kennedy Space Center, Florida

This Operations, Maintenance, and Monitoring Report documents groundwater interim measure activities from March 30, 2019 through December 31, 2019 at the Area South of K7-516 site located at Kennedy Space Center (KSC), Florida. An air sparge (AS) system consisting of 16 AS wells was installed along the Barge Canal in 2012 to be protective of the Outstanding Florida Waters (OFW). The AS system was expanded in 2015 by installing 40 AS wells to remediate the hot spot (HS) area. Additional expansion activities were performed in 2018 through the installation of eight additional AS wells along the Barge Canal. Currently 24 OFW and 40 HS AS wells are in operation. This report includes performance monitoring events for the OFW and HS areas, along with an annual Interim Groundwater Monitoring (IGWM) event in the Western Area. The 516S site has been designated Solid Waste Management Unit 100 under KSC’s Resource Conservation and Recovery Act Corrective Action program. This document was prepared by Tetra Tech, Inc., for the National Aeronautics and Space Administration under Indefinite Delivery Indefinite Quantity Contract 80KSC019D0011/80KSC019F0068. The OFW and HS AS systems are meeting the performance criteria and IM objectives of preventing contaminant migration and remediating groundwater within the treatment zone. Team consensus was reached to continue operation of the combined OFW and HS AS systems (Meeting Minute 2002-M02, Decisions 2002-D06, D09 and D04). Team consensus was also reached to continue semi-annual OFW performance monitoring and annual monitoring for the IGWM Western Area for the same wells sampled during 2019 events. In the eastern area, MW13, MW14, and MW15 will be reduced from semi-annual to annual frequency. For the HS Area, team consensus was reached to continue the current annual/biennial monitoring program (Meeting Minute 2002-M02, Decisions 2002-D02, D03, D05, D07 and D08).

Patrice L. Lehocky↗

NASA NTRSDate not supplied

Recommendations For Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar Eva

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

E L Dillon↗

NASA NTRSDate not supplied

Recommendations for Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar EVA

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

space suit↗

NASA NTRS1974

Wash water solids removal system study

During wash water purification, surfactants tend to precipitate and foul the RO membranes, causing water flux decline and loss of salt rejection. The use of 165 to 190 ppm ferric chloride and optionally 0.25 to 1.0 ppm polymeric flocculate precipitates 92 to 96 percent of the surfactant from an Olive Leaf Soap based wash water. Crossflow filtration and pressure filtration yield good soap rejection at high water flux rates. Post-treatment of the chemically pretreated and filtered wash water with activated charcoal removes the residual soap down to an undetectable level.

Source record↗

NASA NTRS1979

Tropospheric electrification

The solid Earth carried a negative charge of approximately 10 C to the 6 th power and the lower atmosphere an equal, opposite charge. While a number of charging processes in the lower atmosphere are involved, such as erupting volcanoes, snow, sand and dust storms, and the bubbles bursting from the oceans, the primary cause of the Earth's electrification is activity of thunderstorms. Although it is known that the electrification of these clouds is caused by the accumulation of regions of charged water particles, there is no general agreement concerning which process is the cause of the electrification within the cloud and what role this electrification plays in the meteorological processes that take place in the lower atmosphere. The development of thunderclouds and the electric fields and currents above them are discussed.

Vonnegut, B.↗

NASA NTRS1979

Review of composite propellant burn rate modeling

Steady-state combustion modeling of composite solid propellants is discussed with emphasis on the Beckstead-Derr-Price (BDP) model. The BDP model and some revisions are considered with respect to the analysis of monomodal ammonium perchlorate/inert binder propellants: topics examined include continuity relations, surface area relations, characteristic surface dimension, flame heights, and energy balance. Application of the BDP model to more complicated propellants containing multiple active ingredients is described. These propellants include multimodal, mixed oxidizer, active binder, aluminized, catalyzed, and nitramine propellants. Example cases of modeling (with comparison to experimental data) are presented, and strengths and weaknesses of current modeling approaches are evaluated.

Cohen, N. S.↗

NASA NTRS1999

Using Science and the Internet as Everyday Classroom Tools

The Everyday Classroom Tools project developed a K-6 inquiry-based curriculum to bring the tools of scientific inquiry, together with the Internet, into the elementary school classroom. Our curriculum encourages students and teachers to experience the adventure of science through investigation of the world around us. In this project, experts in computer science and astronomy at SAO worked closely with teachers and students in Massachusetts elementary schools to design and model activities which are developmentally appropriate, fulfill the needs of the curriculum standards of the school district, and provide students with a chance to experience for themselves the joy and excitement of scientific inquiry. The results of our efforts are embodied in the Threads of Inquiry, a series of free-flowing dialogues about inquiry-inspiring investigations that maintain a solid connection with our experience and with one another. These investigations are concerned with topics such as the motion of the Earth, shadows, light, and time. Our work emphasizes a direct hands-on approach through concrete experience, rather than memorization of facts.

Mandel, Eric↗

NASA NTRS1999

Hubble Space Telescope Servicing Mission 3A

The Hubble Space Telescope's purpose is to spend 20 years probing the farthest and faintest reaches of the cosmos. Crucial to fulfilling this objective is a series of on-orbit servicing missions. Hubble was placed in orbit on April 25, 1990, by the shuttle Discovery and subsequent servicing followed in December 1993 and February 1997. The third in the series of planned servicing missions for the Hubble Space Telescope was scheduled for June 2000. This third Servicing Mission has been separated into two flights. The first of these flights, Servicing Mission 3A, is scheduled for December 1999, and the second, Servicing Mission 3B, is scheduled for 2001. The fourth Servicing Mission is scheduled for 2003 with a "close-out" Mission in 2010. Three instruments are currently in active scientific use on Hubble - the Wide Field and Planetary Camera 2, the Space Telescope Imaging Spectrograph, and Fine Guidance Sensor I R, which has been designated as the prime FGS for astrometric science. Other instrument bays are occupied by the Near Infrared Camera and Multi-Object Spectrometer (NICMOS), which is now dormant due to the depletion of its solid nitrogen cryogen, the Faint Object Camera, which has been decommissioned, and the corrective optical device called COSTAR, which is no longer needed.

Source record↗

NASA NTRS1992

STS-49 Endeavour/Compiled Video for Editors

Compiled footage includes shots taken of the rollout of Endeavour at Palmdale, CA, the departure and arrival of Endeavour for Kennedy Space Center (KSC), main engine three installation, solid rocket booster (SRB) segment lift and stack at the Vehicle Assembly Building (VAB), external tank mate to SRB, Intelsat rotation at the Vertical Processing Facility (VPF), Endeavour rollover from the Orbiter Processing Facility (OPF) to VAB, rollout to Pad B, and the flight readiness firing (FRF). The crew is seen during the Terminal Countdown and Demonstration Test (TCDT) training activities, at breakfast, suiting up, and exiting the Operations and Checkout (O&C) Building.

Source record↗

NASA NTRS2026

A Modular Conjugate Heat Transfer Optimization Framework for Thermal Management of Electric Aircraft

Conjugate heat transfer (CHT) analysis and optimization is a powerful method for improving thermal management, as it simultaneously resolves the temperature distribution in both fluid and solid domains. This paper presents a modular, discrete adjoint-based CHT optimization capability integrated within the OpenMDAO/MPhys framework. A unique feature of the proposed framework is its flexibility to extend to multidisciplinary optimization, including aero-structural-thermal applications. The fluid domain is modeled using a finite-volume Computational Fluid Dynamics (CFD) solver, and the solid domain with a conduction heat transfer solver. A mixed Neumann-Dirichlet boundary condition is developed to enable full submersion of the solid geometry within the fluid domain, while ensuring consistent temperature and heat flux coupling at the CHT interface. Gradient-based optimization is performed; the gradients are efficiently computed using the discrete adjoint solvers implemented in DAFoam. To demonstrate the method, this paper considers two cases related to electric aircraft thermal management: a U-bend heat exchanger and an actively cooled battery pack. The U-bend case aims to minimize pressure loss while maximizing heat flux by changing the pipe geometry. The optimized design reduces pressure loss by 52.7% and increases total heat flux by 2.3%. In the battery pack case, a 3-by-3 cell configuration is cooled by ambient airflow, with constant heat generation prescribed in the cells. The battery casing shape serves as the design variable, and the objective function is a weighted sum of pressure loss and pack weight, subject to a maximum temperature constraint. The optimized design achieves a 44.6% reduction in pressure loss and a 1.5% reduction in weight, while satisfying the thermal constraint. To ensure the reliability of the optimized designs, this study validates coarse-mesh, steady-state predictions against fine-mesh unsteady simulations, demonstrating consistency within acceptable errors. This work demonstrates the potential of the developed framework to enable rapid, high-fidelity design of thermal management systems for electric aircraft.

heat transfer↗

NASA NTRS2003

Elevated Temperature Creep Deformation in Solid Solution <001> NiAL-3.6Ti Single Crystals

The 1100 to 1500 K slow plastic strain rate compressive properties of <001> oriented NiAl-3.6Ti single crystals have been measured, and the results suggests that two deformation processes exist. While the intermediate temperature/faster strain rate mechanism is uncertain, plastic flow at elevated temperature/slower strain rates in NiAl-3.6Ti appears to be controlled by solute drag as described by the Cottrell-Jaswon solute drag model for gliding b = a(sub 0)<101> dislocations. While the calculated activation energy of deformation is much higher (approximately 480 kJ/mol) than the activation energy for diffusion (approximately 290 kJ/mol) used in the Cottrell-Jaswon creep model, a forced temperature compensated - power law fit using the activation energy for diffusion was able to adequately (greater than 90%) predict the observed creep properties. Thus we conclude that the rejection of a diffusion controlled mechanism can not be simply based on a large numerical difference between the activation energies for deformation and diffusion.

Whittenberger, J. Daniel↗