Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermal Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

End-of-Life Optical Property Predictions of White Conductive Thermal Control Coatings through Analysis of On-Orbit and Ground Based Testing Data

New system requirements pertaining to thermal optical properties and coating electrical properties are commonly specified on non-low earth orbit missions. An increasing number of projects are specifying coatings with a surface resistivity of less than lE-9 ohm/square to mitigate electrostatic charge buildup events over a range of operational temperatures. There are a limited number of coatings that. meet these electrical property requirements while having flight derived optical properties in representative environments. Goddard Space Flight Center Code 546, Contamination and Thermal Coatings Group has recently explored the variety of electrically conductive white coatings available through domestic vendors to evaluate properties to meet project requirements in a geostationary orbit. The lack of significant flight data in representative environments required the careful selection of samples in ground based tests to establish end of life thermal properties. Attention must be given to the origin and pedigree of samples used on past on-orbit experiments to insure that the present formulations for the materials are similar and will react in similar manner.

Hasegawa, Mark↗

Topex Microwave Radiometer thermal control - Post-system-test modifications and on-orbit performance

The Topex Microwave Radiometer has had an excellent thermal performance since launch. The instrument, however, went through a hardware modification right before launch to correct for a thermal design inadequacy that was uncovered during the spacecraft thermal vacuum test. This paper reports on how the initially obscure problem was tracked down, and how the thermal models were revised, validated, and utilized to investigate the solution options and guide the hardware modification decisions. Details related to test data interpretation, analytical uncertainties, and model-prediction vs. test-data correlation, are documented. Instrument/spacecraft interface issues, where the problem originated and where in general pitfalls abound, are dealt with specifically. Finally, on-orbit thermal performance data are presented, which exhibit good agreement with flight predictions, and lessons learned are discussed.

Lin, Edward I.↗

TOPEX Microwave Radiometer Thermal Control: Post-System-Test Modifications and On-Orbit Performance

The Topex Microwave Radiometer has had an excellent thermal performance since launch. The instrument, however, went through a hardware modification right before launch to correct for athermal design inadequacy that was uncovered during the spacecraft thermal vacuum test. This paper reports on how the initially obscure problem was tracked down, and how the thermal models were revised, validated, and utilized to investigate the solution options and guide the hardware modification decisions. Details related to test data interpretation, analytical uncertainties, and model-prediction vs. test-data correlation, are documented. Instrument/spacecraft interface issues, where the problem originated and where in general pitfalls abound, are dealt with specifically. Finally, on-orbit thermal performance data are presented, which exhibit good agreement with flight predictions, and lessons learned are discussed.

Lin, Edward I.↗

Thermal control requirements for large space structures

Performance capabilities and weight requirements of large space structure systems will be significantly influenced by thermal response characteristics. Analyses have been performed to determine temperature levels and gradients for structural configurations and elemental concepts proposed for advanced system applications ranging from relatively small, low-power communication antennas to extremely large, high-power Satellite Power Systems (SPS). Results are presented for selected platform configurations, candidate strut elements, and potential mission environments. The analyses also incorporate material and surface optical property variation. The results illustrate many of the thermal problems which may be encountered in the development of three systems.

Manoff, M.↗

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗

Thermal control system

The temperature of an exothermic process plant carried aboard an Earth orbiting spacecraft is regulated using a number of curved radiator panels accurately positioned in a circular arrangement to form an open receptacle. A module containing the process is insertable into the receptacle. Heat exchangers having broad exterior surfaces extending axially above the circumference of the module fit within arcuate spacings between adjacent radiator panels. Banks of variable conductance heat pipes partially embedded within and thermally coupled to the radiator panels extend across the spacings and are thermally coupled to broad exterior surfaces of the heat exchangers by flanges. Temperature sensors monitor the temperature of process fluid flowing from the module through the heat exchanges. Thermal conduction between the heat exchangers and the radiator panels is regulated by heating a control fluid within the heat pipes to vary the effective thermal length of the heat pipes in inverse proportion to changes in the temperature of the process fluid.

Hewitt, D. R.↗

Shuttle active thermal control system development testing. Volume 8: Tube anomaly investigation

A modular radiator system projected for use on the space shuttle has been tested. During thermal vacuum testing of the radiator panels leaks developed in the coolant fluid tubes containing the Freon 21 refrigerant. An analysis of thermal vacuum test conditions revealed that the test anomaly consisted of trapped Freon 21 fluid between frozen tube corners colder than the remainder of the panel. The trapped fluid expanded on further warming, causing high pressures to develop in the tubes. The pressure was sufficient to induce tube ruptures. Metallurgical analysis showed that concentric extrusion holes and heat treatment of the aluminum alloy to the -T6 condition would have prevented the ruptures. Thermal analysis indicates that attaching the tube corners to the radiator fin could eliminate the fluid trapping.

Reed, M. W.↗

Electronic Speed Controller Thermal Management

This experiment was coupled with an acoustic test for NASA’s QUiet Electric ENgine (QUEEN). A cold plate with water was used to cool the electronic speed controller of the motor under different conditions (shown on right). Part 1: Fixed motor RPM, translating to fixed power/heat dissipation (4W per MOSFET) of electrical components, with variable cooling capacity measured by flow rate of cold plate water in gpm. Part 2: Fixed cooling power (1 gpm) with variable RPM.

thermal↗

Preliminary investigations into UHCRE thermal control materials (A0178)

An overview of the initial work that was done in the ESTEC Materials and Processes Division to evaluate the effect of space environment on the thermal blankets of the Ultra-Heavy Cosmic Ray Nuclei Experiments (UHCRE) is presented. The topics covered include: (1) a preliminary survey of the perforations of the two-thirds of the thermal blanket returned to ESTEC; (2) thermo-optical properties and thickness recessions of three samples cut from each of the third center parts of the 16 thermal blankets were measured and effects of environments (sun illumination and atomic oxygen fluences); (3) contamination was analyzed on trays, external blanket and internal aluminized Kapton foil by IR technique and scanning electron microscopy SEM/EDX examination; (4) the pattern of contamination on the Al Kapton foils was observed, sketched, and related to atomic oxygen flow; and (5) the Long Duration Exposure Facility (LDEF) yaw angle misorientation was evaluated from the contaminated areas visible on some of the trays. In addition, impacts of micrometeoroids and space debris were experimentally simulated on spare flight thermal blankets. Relations between penetration/perforation hole characteristics and projectile parameters were established.

Levadou, Francois↗

MSFC Skylab Apollo Telescope Mount thermal control system mission evaluation

The Skylab Saturn Workshop Assembly was designed to expand the knowledge of manned earth orbital operations and accomplish a multitude of scientific experiments. The Apollo Telescope Mount (ATM), a module of the Skylab Saturn Workshop Assembly, was the first manned solar observatory to successfully observe, monitor, and record the structure and behavior of the sun outside the earth's atmosphere. The ATM contained eight solar telescopes that recorded solar phenomena in X-ray, ultraviolet, white light, and hydrogen alpha regions of the electromagnetic spectrum. In addition, the ATM contained the Saturn Workshop Assembly's pointing and attitude control system, a data and communication system, and a solar array/rechargeable battery power system. This document presents the overall ATM thermal design philosophy, premission and mission support activity, and the mission thermal evaluation. Emphasis is placed on premission planning and orbital performance with particular attention on problems encountered during the mission. ATM thermal performance was satisfactory throughout the mission. Although several anomalies occurred, no failure was directly attributable to a deficiency in the thermal design.

Hueter, U.↗

Multiphase Flow Technology Impacts on Thermal Control Systems for Exploration

The Two-Phase Flow Facility (TPHIFFy) Project focused on bridging the critical knowledge gap by developing and demonstrating critical multiphase fluid products for advanced life support, thermal management and power conversion systems that are required to enable the Vision for Space Exploration. Safety and reliability of future systems will be enhanced by addressing critical microgravity fluid physics issues associated with flow boiling, condensation, phase separation, and system stability. The project included concept development, normal gravity testing, and reduced gravity aircraft flight campaigns, in preparation for the development of a space flight experiment implementation. Data will be utilized to develop predictive models that could be used for system design and operation. A single fluid, two-phase closed thermodynamic loop test bed was designed, assembled and tested. The major components in this test bed include: a boiler, a condenser, a phase separator and a circulating pump. The test loop was instrumented with flow meters, thermocouples, pressure transducers and both high speed and normal speed video cameras. A low boiling point surrogate fluid, FC-72, was selected based on scaling analyses using preliminary designs for operational systems. Preliminary results are presented which include flow regime transitions and some observations regarding system stability.

McQuillen, John↗

Robust Thermal Control of Propulsion Lines for Space Missions

In spacecraft that have propulsion lines that are located externally with open bus architecture, the lines are typically insulated by Multi Layer Insulation (MLI) blankets to protect them thermally from the cold space environment. In addition to heat loss through the insulation, mechanical supports used to attach the lines to the spacecraft structure also create heat leaks from the lines. These lines typically have very low thermal conduction in the axial direction, so the heat balance in the lines tends to be very local without much heat spreading. The typical allowable temperature range for hydrazine-based lines is +15/+50°C. This tight temperature range has to be maintained for every location on these lines. For typical spacecraft, these lines can be several meters long. Temperature control is typically achieved by closed loop monitoring of temperatures along the lines and the corresponding powering of the heaters in a bang-bang approach to maintain the temperatures within the dead band of the control loop. The temperatures of propulsion lines are a function of several parameters with heat loss characteristics of the MLI being the key one. Unfortunately, this same key characteristic (MLI effective emittance) has a large variation along its length due to its dependence on workmanship, which in turn leads to large uncertainties in the propulsion lines’ local temperatures. Because of the poor conduction along the axial direction, heat balance along the length varies dramatically from one location to the next, even few inches apart, depending on the combination of the controlling parameters. This paper describes various robust design and implementation approaches that have been investigated to greatly reduce the randomness associated with predicting the temperature of these propulsion lines.

Bhandari, Pradeep↗

Time-Separating Heating and Sensor Functions of Thermistors in Precision Thermal Control Applications

A method allows combining the functions of a heater and a thermometer in a single device, a thermistor, with minimal temperature read errors. Because thermistors typically have a much smaller thermal mass than the objects they monitor, the thermal time to equilibrate the thermometer to the temperature of the object is typically much shorter than the thermal time of the object to change its temperature in response to an external perturbation.

Cho, Hyung J.↗

Manipulating Conjugated Polymer Backbone Dynamics through Controlled Thermal Cleavage of Alkyl Side Chains

The morphological stability of an organic photovoltaic (OPV) device is greatly affected by the dynamics of donors and acceptors occurring near the device's operational temperature. These dynamics can be quantified by the glass transition temperature (T g ) of conjugated polymers (CPs). Because flexible side chains possess much faster dynamics, the cleavage of the alkyl side chains will reduce chain dynamics, leading to a higher T g . In this work, the T g s for CPs are systematically studied with controlled side chain cleavage. Isothermal annealing of polythiophenes featuring thermally cleavable side chains at 140 °C, is found to remove more than 95% of alkyl side chains in 24 h, and raise the backbone T g from 23 to 75 °C. Coarse grain molecular dynamics simulations are used to understand the T g dependence on side chain cleavage. X-ray scattering indicates that the relative degree of crystallization remains constantduring isothermal annealing process. The effective conjugation length is not influenced by thermal cleavage; however, the density of chromophore is doubled after the complete removal of alkyl side chains. Here, the combined effect of enhancing T g and conserving crystalline structures during the thermal cleavage process can provide a pathway to improving the stability of optoelectronic properties in future OPV devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tracking single quantum dot and its spectrum in free solution with controllable thermal diffusion suppression

Thermal motions of semiconductor quantum dots (QDs) are suppressed on a dehydrated agarose-modified surface. The diffusion coefficients (D) of particles can be controlled by modifying the surface with an appropriate agarose concentration. The value of D is more than 100 times lower than the theoretical value when the dried agarose surface is made with an 8% agarose solution. This makes it possible to real-time record the diffusion process of single particles and single molecules in low-viscosity solution. A transmission grating installed in front of the charge-coupled device separates the QD fluorescence into the zeroth-order and first-order spectrum. Therefore, the spectrum of dynamic QDs is tracked on the modified surface. Tracking the dynamic QD spectral image is a promising method to explore the process of the molecular interactions in the physiological buffer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗