Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRIBOLOGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Sputtered cadmium oxide as a surface pretreatment for graphite solid lubricant films

Sputtered films of cadmium oxide were applied to sand blasted AISI 440C HT stainless steel disks as a surface pretreatment for the application of rubbed graphite films. Mixtures of cadmium oxide and graphite were applied to the nonpretreated sandblasted metal and evaluated. The results were compared to graphite films applied to other commercially available surface pretreatments. It is found that sputtered CdO pretreated surfaces increase the endurance lives of the graphite films and decrease the counterface steady state wear rate of the pins almost an order of magnitude compared to commercially available pretreatments. The CdO additions in general improved the tribological properties of graphite. The greatest benefit occurred when it was applied to the substrate rather than mixing it with the graphite and that sputtered films of CdO perform much better than rubbed CdO films.

Fusaro, R. L.↗

Adhesion, friction, and deformation of ion-beam-deposited boron nitride films

The tribological properties and mechanical strength of boron nitride films were investigated. The BN films were predominantly amorphous and nonstoichiometric and contained small amounts of oxides and carbides. It was found that the yield pressure at full plasticity, the critical load to fracture, and the shear strength of interfacial adhesive bonds (considered as adhesion) depended on the type of metallic substrate on which the BN was deposited. The harder the substrate, the greater the critical load and the adhesion. The yield pressures of the BN film were 12 GPa for the 440C stainless steel substrate, 4.1 GPa for the 304 stainless steel substrate, and 3.3 GPa for the titanium substrate.

Miyoshi, Kazuhisa↗

The 20th Aerospace Mechanisms Symposium

Numerous topics related to aerospace mechanisms were discussed. Deployable structures, electromagnetic devices, tribology, hydraulic actuators, positioning mechanisms, electric motors, communication satellite instruments, redundancy, lubricants, bearings, space stations, rotating joints, and teleoperators are among the topics covered.

Source record↗

Towards an optimised sputtered MoS2 lubricant film

It is shown that the tribological quality of MoS2 lubricant films formed by magnetron sputtering is determined by the choice of sputtering conditions. By selecting the appropriate conditions, films of extremely high lubricity and endurance (in vacuum), which are well suited to many space applications, are obtained. Such MoS2 films, when applied to precision ball hearings, give rise to the lowest torques (for the given test conditions) yet seen in our laboratory. While a remarkably good performance is obtained in vacuum, tests in air show a marked deterioration in lubricating qualities. It is demonstrated that this is attributable to the adsorption of water vapor on MoS2 surfaces and that the degree of deterioration is related to the partial pressure of water vapor present. Analysis of results indicates that the factors relevant to obtaining optimum films are deposition rate and film composition.

Roberts, E. W.↗

Experimental evaluation of chromium-carbide-based solid lubricant coatings for use to 760 C

A research program is described which further developed and investigated chromium carbide based self-lubricating coatings for use to 760 C. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The three coating components were blended in powder form, applied to stainless steel substrates by plasma spraying and then diamond ground to the desired coating thickness. A variety of coating compositions was tested to determine the coating composition which gave optimum tribological results. Coatings were tested in air, helium, and hydrogen at temperatures from 25 to 760 C. Several counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications, such as piston ring/cylinder liner couples for Stirling engines. In general, silver and fluoride additions to chromium carbide reduced the friction coefficient and increased the wear resistance relative to the unmodified coating. The lubricant additives acted synergistically in reducing friction and wear.

Dellacorte, Christopher↗

The 21st Aerospace Mechanisms Symposium

During the symposium technical topics addressed included deployable structures, electromagnetic devices, tribology, actuators, latching devices, positioning mechanisms, robotic manipulators, and automated mechanisms synthesis. A summary of the 20th Aerospace Mechanisms Symposium panel discussions is included as an appendix. However, panel discussions on robotics for space and large space structures which were held are not presented herein.

Source record↗

Microstructure and surface chemistry of amorphous alloys important to their friction and wear behavior

An investigation was conducted to examine the microstructure and surface chemistry of amorphous alloys, and their effects on tribological behavior. The results indicate that the surface oxide layers present on amorphous alloys are effective in providing low friction and a protective film against wear in air. Clustering and crystallization in amorphous alloys can be enhanced as a result of plastic flow during the sliding process at a low sliding velocity, at room temperature. Clusters or crystallines with sizes to 150 nm and a diffused honeycomb-shaped structure are produced on sizes to 150 nm and a diffused honeycomb-shaped structure are produced on the wear surface. Temperature effects lead to drastic changes in surface chemistry and friction behavior of the alloys at temperatures to 750 C. Contaminants can come from the bulk of the alloys to the surface upon heating and impart to the surface oxides at 350 C and boron nitride above 500 C. The oxides increase friction while the boron nitride reduces friction drastically in vacuum.

Miyoshi, K.↗

Adhesion, friction and deformation of ion-beam-deposited boron nitride films

The tribological properties and mechanical strength of boron nitride films were investigated. The BN films were predominantly amorphous and nonstoichiometric and contained small amounts of oxides and carbides. It was found that the yield pressure at full plasticity, the critical load to fracture, and the shear strength of interfacial adhesive bonds (considered as adhesion) depended on the type of metallic substrate on which the BN was deposited. The harder the substrate, the greater the critical load and the adhesion. The yield pressures of the BN film were 12 GPa for the 440C stainless steel substrate, 4.1 GPa for the 304 stainless steel substrate, and 3.3 GPa for the titanium substrate.

Miyoshi, K.↗

Lubrication And Wear Of Hot Ceramics

Report presents results of experiments on tribological properties of ceramics. Describes friction and wear characteristics of some ceramics under consideration for use in gas turbines, diesel engines, and Stirling engines. Discusses formulation of composite plasma-sprayed ceramics containing solid lubricant additives, and data for carbide- and oxide-based composite coatings for use at temperatures up to at least 900 degree C.

Sliney, H. E.↗

Sputtered silver films to improve chromium carbide based solid lubricant coatings for use to 900 C

Thin silver films, 250 to 3500 A thick, were sputtered onto PS200, a plasma sprayed, chromium carbide based solid lubricant coating, to reduce run-in wear and improve tribological properties. The coating contains bonded chromium carbide as the wear resistant base stock with silver and barium fluoride/calcium fluoride eutectic added as low and high temperature lubricants respectively. Potential applications for the PS200 coating are cylinder wall/piston ring lubrication for Stirling engines and foil bearing journal lubrication. In this preliminary program, the silver film overlay thickness was optimized based on tests using a pin-on-disk tribometer. The friction and wear studies were performed in a helium atmosphere at temperatures from 25 to 760 C with a sliding velocity of 2.7 m/s under a 4.9 N load. Films between 1000 and 1500 A provide the best lubrication of the counterface material. The films enrich the sliding surface with lubricant and reduce the initial abrasiveness of the as ground, plasma-sprayed coating surface, thus reducing wear.

Dellacorte, Christopher↗

Friction and Wear of Monolithic and Fiber Reinforced Silicon-Ceramics Sliding Against IN-718 Alloy at 25 to 800 C in Atmospheric Air at Ambient Pressure

The friction and wear of monolithic and fiber reinforced Si-ceramics sliding against the nickel base alloy IN-718 at 25 to 800 C was measured. The monolithic materials tested were silicon carbide (SiC), fused silica (SiO2), syalon, silicon nitride (Si3N4) with W and Mg additives, and Si3N4 with Y2O3 additive. At 25 C fused silica had the lowest friction while Si3N4 (W,Mg type) had the lowest wear. At 800 C syalon had the lowest friction while Si3N4 (W,Mg type) and syalon had the lowest wear. The SiC/IN-718 couple had the lowest total wear at 25 C. At 800 C the fused silica/IN-718 couple exhibited the least total wear. SiC fiber reinforced reaction bonded silicon nitride (RBSN) composite material with a porosity of 32 percent and a fiber content of 23 vol percent had a lower coefficient of friction and wear when sliding parallel to the fiber direction than in the perpendicular at 25 C. The coefficient of friction for the carbon fiber reinforced borosilicate composite was 0.18 at 25 C. This is the lowest of all the couples tested. Wear of this material was about two decades smaller than that of the monolithic fused silica. This illustrates the large improvement in tribological properties which can be achieved in ceramic materials by fiber reinforcement. At higher temperatures the oxidation products formed on the IN-718 alloy are transferred to the ceramic by sliding action and forms a thin, solid lubricant layer which decreases friction and wear for both the monolithic and fiber reinforced composites.

Deadmore, Daniel L.↗

Interfacial adhesion: Theory and experiment

Adhesion, the binding of different materials at an interface, is of general interest to many branches of technology, e.g., microelectronics, tribology, manufacturing, construction, etc. However, there is a lack of fundamental understanding of such diverse interfaces. In addition, experimental techniques generally have practical objectives, such as the achievement of sufficient strength to sustain mechanical or thermal effects and/or have the proper electronic properties. In addition, the theoretical description of binding at interfaces is quite limited, and a proper data base for such theoretical analysis does not exist. This presentation will review both experimental and theoretical aspects of adhesion in nonpolymer materials. The objective will be to delineate the critical parameters needed, governing adhesion testing along with an outline of testing objectives. A distinction will be made between practical and fundamental objectives. Examples are given where interfacial bonding may govern experimental consideration. The present status of theory is presented along wiith recommendations for future progress and needs.

Ferrante, John↗

Structural Ceramics

This publication is a compilation of abstracts and slides of papers presented at the NASA Lewis Structural Ceramics Workshop. Collectively, these papers depict the scope of NASA Lewis' structural ceramics program. The technical areas include monolithic SiC and Si3N4 development, ceramic matrix composites, tribology, design methodology, nondestructive evaluation (NDE), fracture mechanics, and corrosion.

Source record↗

Ceramics for turbine engines

The Ceramics for Turbine Engines Project is comprised of three main research programs with major elements as indicated: materials and processing (monolithics and fiber reinforcement), design methodology (design code and tribology), and life prediction (environmental effects, nondestructive evaluation, fracture and fatigue, and time dependent behavior). From the NASA perspective an enhanced ceramics technology base directly supports aeronautics initiatives in small engine technology, high-performance turbine engine technology, and hypersonics. An overview of the program, which includes the technical objectives and content of each program, is provided.

Levine, Stanley R.↗

Sputtered cadmium oxide as a surface pretreatment for graphite solid-lubricant films

Sputtered films of cadmium oxide were applied to sand blasted AISI 440C HT stainless steel disks as a surface pretreatment for the application of rubbed graphite films. Mixtures of cadmium oxide and graphite were applied to the nonpretreated sandblasted metal and evaluated. The results were compared to graphite films applied to other commercially available surface pretreatments. It is found that sputtered CdO pretreated surfaces increase the endurance lives of the graphite films and decrease the counterface steady state wear rate of the pins almost an order of magnitude compared to commercially available pretreatments. The CdO additions in general improved the tribological properties of graphite. The greatest benefit occurred when it was applied to the substrate rather than mixing it with the graphite and that sputtered films of CdO perform much better than rubbed CdO films.

Fusaro, Robert L.↗

Sputtered silver films to improve chromium carbide based solid lubricant coatings for use to 900 C

Thin silver films, 250 to 3500 A thick, were sputtered onto PS200, a plasma sprayed, chromium carbide based solid lubricant coating, to reduce run-in wear and improve tribological properties. The coating contains bonded chromium carbide as the wear resistant base stock with silver and barium fluoride/calcium fluoride eutectic added as low and high temperature lubricants, respectively. Potential applications for the PS200 coating are cylinder wall/piston ring lubrication for Stirling engines and foil bearing journal lubrication. In this preliminary program, the silver film overlay thickness was optimized based on tests using a pin-on-disk tribometer. The friction and wear studies were performed in a helium atmosphere at temperatures from 25 to 760 C with a sliding velocity of 2.7 m/s under a 4.9 N load. Films between 1000 and 1500 A provide the best lubrication of the counterface material. The films enrich the sliding surface with lubricant and reduce the initial abrasiveness of the as ground, plasma-sprayed coating surface, thus reducing wear.

Dellacorte, Christopher↗

Space station long-term lubrication analysis

The objectives of this program are: (1) to perform a complete tribology survey of every point of contact in the space station subject to relative motion regarding the materials, environment, and operation characteristics, (2) to review each point of relative motion regarding the selected materials and lubricants from the standpoint of the required operating characteristics and environmental conditions, (3) to make recommendations for improvements where the lubricants and/or materials are not considered optimum, and (4) to perform or recommend simulated or full-scale tests on components where problems are possible or likely because of new designs, significant design extensions beyond current practice, or sensitivity of other components to problems with a particular point of contact. The project is to be conducted over a 3-year time frame in two phases. Phase 1 will be a preliminary analysis conducted during the preliminary design phases of the Space Station. Phase 2 will be a more detailed analysis conducted during the period when the design becomes more established.

Dufrane, K. F.↗

Interfacial adhesion - Theory and experiment

Adhesion, the binding of different materials at an interface, is of general interest to many branches of technology, e.g., microelectronics, tribology, manufacturing, construction, etc. However, there is a lack of fundamental understanding of such diverse interfaces. In addition, experimental techniques generally have practical objectives, such as the achievement of sufficient strength to sustain mechanical or thermal effects and/or have the proper electronic properties. In addition, the theoretical description of binding at interfaces is quite limited, and a proper data base for such theoretical analysis does not exist. This presentation will review both experimental and theoretical aspects of adhesion in nonpolymer materials. The objective will be to delineate the critical parameters needed, governing adhesion testing along with an outline of testing objectives. A distinction will be made between practical and fundamental objectives. Examples are given where interfacial bonding may govern experimental consideration. The present status of theory is presented along with recommendations for future progress and needs.

Ferrante, John↗