Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Effect of processing parameters and strut dimensions on the microstructures and hardness of stainless steel 316L lattice-emulating structures made by powder bed fusion

In this study, we present the effects of input processing parameters and strut thickness (in square struts) on microstructure and properties in laser powder bed fusion additively manufactured stainless steel 316L lattice-emulating structures. Lattice-emulating X-structures with square cross-sections of 1.5, 1.0, and 0.5 mm were fabricated using three different parameter sets with varying power, speed, and therefore, linear energy density. Grain size and morphology were shown to be dictated by epitaxial growth, which was dependent on weld pool morphology. Additionally, grain size and morphology were shown to change across the thickness direction of the struts (from the bottom inclined surface to the top inclined surface). The spatial variation in grain size was reflected by changes in hardness through the thickness of each strut. The 0.5 mm struts exhibited more significant grain elongation in the strut direction and larger sub-grain solidification cell diameters than their thicker counterparts. The larger sub-grain solidification cell diameters in the 0.5 mm samples resulted in correspondingly lower hardness values when compared to samples of higher thicknesses.

36 MATERIALS SCIENCE↗

Carbon nanotube (CNT) reinforced 316L stainless steel composites made by laser powder bed fusion: Microstructure and wear response

Carbon nanotube (CNT) reinforced 316L stainless steel (SS) composites were fabricated by laser powder bed fusion (LPBF) additive manufacturing (AM). This study focuses on microstructure evolution, hardness, and wear behavior. The wear behavior for AM 316L SS and 1 wt% CNT/316L SS was studied by a dry sliding test under normal loads of 10, 15, and 25 N. The addition of CNT to 316L SS led to the change of solidification mode from cellular/columnar to dendritic growth, producing grain refinement. Nanoscale dendrites were observed. Although TEM characterization confirmed the existence of CNT in cell interior, most CNT were damaged, resulting in carbon material segregation along cellular/dendritic boundaries. The wear rate was found dramatically decreased due to the improved hardness. Compared to the adhesive and abrasive wear in AM 316L SS, the wear mechanism of CNT/316L composite was adhesion and oxidative wear. Furthermore, enhanced cellular/dendritic boundary strengthening by carbon segregation was the main strengthening mechanism of CNT/316L composite.

36 MATERIALS SCIENCE↗

Numerical investigation of electromagnetic pulse welded interfaces between dissimilar metals

The quality of an electromagnetic pulse weld is strongly affected by a variety of interacting physical phenomena including large plastic deformation, materials mixing, localised heating and rapid cooling, and possible localised melting and interfacial cracks and void. In the present study, a thermomechanically coupled dynamic model has been developed to quantitatively resolve the high speed impact joining interface characteristics as well as the process induced interface temperature evolution, defect formation and possible microstructural composition variations. Reasonably good agreement has been obtained between the predicted results and the experimental measurements in terms of interfacial morphology characteristics. The modelling framework is expected to provide further understanding of the hierarchical interfacial features of the non-equilibrium material joining process and the weld formation mechanisms.

Xu, W.↗

Directionally Solidified Ceramics Produced

Produced Multiphase, interpenetrating structures are an alternative route to obtaining structural ceramic materials with adequate strength, toughness, and stability for high-temperature aerospace applications. The eutectic architecture, a continuous-reinforcing phase within a higher volume phase or matrix, can be described as a naturally occurring, in situ composite. The phases of a eutectic are thermodynamically compatible at high homologous temperatures. Strong and stable materials have been produced. Toughness, however, remains a technical obstacle. The potential for producing materials with enhanced toughness along with adequate strength and stability was demonstrated using the laser-heated float zone (LHFZ) growth method at the NASA Glenn Research Center at Lewis Field. LHFZ growth at Glenn provides a means to efficiently produce and record the underlying growth phenomena associated with two-phase structures. To initiate directional solidification, a seed of single-crystal sapphire (<0001> direction) was lowered onto the molten liquid until wetting occurred and then withdrawn at a constant rate. Neither the crystal nor the source rod was rotated. The materials produced were tested mechanically in tension, and the resulting microstructure was examined with a scanning electron microscope. Both the inherent properties of the constituent phases and the properties of the interface between them affect the mechanical behavior and the fracture surfaces. The following scanning electron micrographs show the microstructures of two different materials that were tested to failure in tension. In the left micrograph, the flat fracture surface is typical of a material that is strong but has low toughness. In the right micrograph, the crack is effectively deflected at the interface between the two phases, achieving higher toughness at moderately lower strength levels. Conducting mechanical tests to determine the high temperature properties of these materials is the next step in determining their eventual suitability.

Farmer, Serene C.↗

Microstructural and mechanical characterization of Al–Zn–Si nanocomposites

In this paper the addition of silicon nanoparticles into Al–Zn alloys to form metallic matrix nanocomposites by mechanical alloying process was investigated. The influence of various process parameters such as milling time and Si concentration in the Al–Zn matrix has an interesting effect on the microstructure and mechanical properties of the synthesized nanocomposites. The microstructural characterization of the nanocomposites was evaluated by transmission electron microscopy and energy dispersive X-ray spectroscopy (TEM–EDXS) and the mechanical properties were measured by nanoindentation and micro-hardness tests. The results showed that during mechanical milling Si is added to the Al–Zn matrix achieving a uniform and homogeneous dispersion. After solidification, it forms small particles of AlZnSi with blocky morphology in interdendritic regions. The nanoindentation profiles showed that the elastic modulus and hardness properties increase with increasing milling time. However, a high concentration of Si (> 1.2 wt.%) results in a saturation of Si in the Al–Zn matrix, which adversely affects the mechanical properties. Thus, it is important to tune the milling time and concentration of Si added to the Al–Zn alloys to control the growth of brittle phases that result in reduction of the mechanical properties of the material. - Highlights: • A novel technique for addition of Si nanocomposites into Al–Zn liquid alloy is reported. • Good dispersion and homogeneity of Si in the Al–Zn matrix are obtained. • Increasing Si content above 1.2 wt.% decreases the mechanical properties of Al–Zn alloy. • The saturation point of Si in 1.2 wt.% differs from Galvalume® composition. • The Al–Zn–1.5Si alloy with addition of nanocomposite shows 5.7 GPa of hardness.

36 MATERIALS SCIENCE↗

Rapid solidification of highly undercooled liquids

Melt undercooling is considered as a fundamental processing parameter for powders and for melt-spun and surface-melted samples. With reference to experimental results for Mn, Al, Al-Be, Al-Fe, and InSb-Sb powders, it is shown that the undercooling behavior in droplets is influenced by powder size, coating, melt superheat, and cooling rate. Droplet sample microstructures can be compared directly with those of rapidly quenched powders to establish the application of laboratory-scale studies to large-scale processing.

Perepezko, J. H.↗

Design of novel refractory equiatomic multi-principal elemental alloys based on Mo-Nb-Ti system for Gen IV reactor applications

Excellent irradiation damage resistance demonstrated by multi-principal elemental alloys (MPEAs) has sparked significant interest among researchers, prompting exploration into their vast compositional space, to validate their suitability for nuclear applications. A combined approach of thermodynamic and empirical parameters calculations alongside CALPHAD (CALculation of PHAse Diagrams) for phase formation predictions enable high-throughput material selection for sophisticated applications like nuclear, overcoming laborious and time-consuming experiments. Key thermodynamic and empirical parameters for eight novel equiatomic MPEAs, based on seven low thermal neutron cross section refractory elements, for predicting phase formation were calculated, and equilibrium and non-equilibrium simulations in CALPHAD were employed to comprehensively model the systems. Pseudo binary phase diagram simulations showed that Zr, V or equiatomic CrV additions to the base MoNbTi alloy (MoNbTi-Zr, MoNbTi-V and MoNbTi-CrV alloys) favor the formation of isomorphous body-centered cubic (BCC) phase at high temperatures, while Cr, Al, equiatomic ZrV, or equiatomic CrAl additions (MoNbTi-Cr, MoNbTi-Al, MoNbTi-ZrV or MoNbTi-CrAl alloys) limit the solubility of them. Equilibrium CALPHAD simulations at 750 oC were consistent with XRD results on MoNbTi, MoNbTiZr and MoNbTiCr alloys, and partially for others. Notably, elemental segregation observed in the backscattered electron (BSE) scanning electron microscopy (SEM) images of the alloys was accurately simulated through non-equilibrium Scheil solidification calculations in CALPHAD, further verified by experiments. The precipitation of TiCr2 Laves phase in Cr containing MoNbTiCr and MoNbTiCrAl was accurately predicted while discrepancies were noted in MoNbTiCrV. The equilibrium simulations also provided insights into phase compositions at specific temperatures offering a pathway for tailoring the desired microstructure and properties of these systems. Empirical parameters calculations successfully predicted random solid solution in the base MoNbTi alloy, and with an exception in MoNbTiV and MoNbTiAl, predicted intermetallic precipitation in the rest, especially, Laves phase precipitation in Cr containing alloys.

36 - MATERIALS SCIENCE↗

The transition from columnar to equiaxed dendritic growth in proeutectic, low-volume fraction copper, Pb-Cu alloys

Lead, 17.1, 11.2, and 5 volume fraction copper (14, 9, and 4 wt pct Cu) alloys have been directionally solidified at constant growth velocities ranging from 1 to 100 microns/s. Serially increasing the growth velocity within this range results in a graded microstructural transition from fully columnar, albeit segregated, copper dendrites in a lead matrix to one consisting only of equiaxed grains. The imposed velocity necessary to effect fully equiaxed growth is found to drop rapidly as the volume fraction of copper is decreased. Factors which complicate the controlled, directional solidification of these alloys are discussed and the experimental results are interpreted in view of, and seen to be in qualitative agreement with, Hunt's theory on the transition from columnar to equiaxed growth of dendrites.

Kim, Shinwoo↗

The Application of Canned Deformation to a Hard-Deformed Spray-Deposited Al-Zn-Mg-Cu Alloy

A wide variety of industrial applications require Al-Zn-Mg-Cu alloys with high strength and ductility. However, Zn-rich Al-Zn-Mg-Cu alloys prepared by rapid solidification methods usually show excellent strength but poor formability, which restricts their wide application in complex forming. In this study, we developed a new deformation method for the spray-deposited Zn-rich Al-Zn-Mg-Cu alloy to avoid crack formation and achieve isotropic properties. The microstructure evolution and crystallographic textures were analyzed and compared with the results of a normal deformation process. Crack-free forgings with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 727 ± 5 MPa, 690 ± 3 MPa, 5.0 ± 0.7% along the radial direction and 735 ± 2 MPa, 693 ± 3 MPa, 6.3 ± 0.2% along the tangential direction were finally obtained. The improvement in the mechanical properties can be attributed to the larger amount of subgrains and substructures generated in the canned deformed alloy. The results of this study show excellent advantages and potential application prospects of the canned deformation to hard-deformed Al-Zn-Mg-Cu alloys.

36 MATERIALS SCIENCE↗

The effect of solidification rate on the formability of nickel aluminide containing iron and boron

Following reports that rapid solidification improves the ductility of some nickel aluminides, an investigation has been conducted of the possibility of additional improvement in a nickel aluminide containing both Fe and B. Free fall-solidified and free fall/splat-quenched samples similar to those producible under microgravity conditions in space were prepared, and their microstructure was characterized. Attention is given to the preliminary results of tests quantitatively measuring mechanical properties.

Carro, G.↗

Laser Welding in Space

Solidification type welding process experiments in conditions of microgravity were performed. The role of convection in such phenomena was examined and convective effects in the small volumes obtained in the laser weld zone were observed. Heat transfer within the weld was affected by acceleration level as indicated by the resulting microstructure changes in low gravity. All experiments were performed such that both high and low gravity welds occurred along the same weld beam, allowing the effects of gravity alone to be examined. Results indicate that laser welding in a space environment is feasible and can be safely performed IVA or EVA. Development of the hardware to perform the experiment in a Hitchhiker-g platform is recomended as the next step. This experiment provides NASA with a capable technology for welding needs in space. The resources required to perform this experiment aboard a Shuttle Hitchhiker-pallet are assessed. Over the four year period 1991 to 1994, it is recommended that the task will require 13.6 manyears and $914,900. In addition to demonstrating the technology and ferreting out the problems encountered, it is suggested that NASA will also have a useful laser materials processing facility for working with both the scientific and the engineering aspects of materials processing in space. Several concepts are also included for long-term optimization of available solar power through solar pumping solid state lasers directly for welding power.

Workman, Gary L.↗

Effect of carbon content on solidification behaviors and morphological characteristics of the constituent phases in Cr-Fe-C alloys

A combination of transmission electron microscopy, electron backscatter diffraction and wavelength dispersive spectrum has been used to identify crystal structure, grain boundary characteristic and chemical composition of the constituent phases in Cr-Fe-C alloys with three different carbon concentrations. Depending on the three different carbon concentrations, the solidification structures are found to consist of primary {alpha}-phase and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-18.4Fe-2.3 C alloy; primary (Cr,Fe){sub 23} C{sub 6} and [{alpha} + (Cr,Fe){sub 23} C{sub 6}] eutectic in Cr-24.5Fe-3.8 C alloy and primary (Cr,Fe){sub 7} C{sub 3} and [{alpha} + (Cr,Fe){sub 7} C{sub 3}] eutectic in Cr-21.1Fe-5.9 C alloy, respectively. The grain boundary analysis is useful to understand growth mechanism of the primary phase. The morphologies of primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides are faceted structures with polygonal shapes, different from primary {alpha}-phase with dendritic shape. The primary (Cr,Fe){sub 23} C{sub 6} and (Cr,Fe){sub 7} C{sub 3} carbides with strong texture exist a single crystal structure and contain a slight low angle boundary, resulting in the polygonal growth mechanism. Nevertheless, the primary {alpha}-phase with relative random orientation exhibits a polycrystalline structure and comprises a massive high-angle boundary, caused by the dendritic growth mechanism. - Highlights: Black-Right-Pointing-Pointer Microstructures of the as-clad Cr-based alloys are characterized by TEM. Black-Right-Pointing-Pointer EBSD technique has been use to characterize the grain boundary of primary phases. Black-Right-Pointing-Pointer We examine transitions in morphology about the primary phases. Black-Right-Pointing-Pointer Morphologies of primary carbides are polygonal different from primary {alpha}-phase. Black-Right-Pointing-Pointer Solidification structures rely on C concentrations in Cr-Fe-C alloy.

36 MATERIALS SCIENCE↗

Microstructure evolution during near-net-shape fabrication of Ni x Al y -TiC cermets through binder jet additive manufacturing and pressureless melt infiltration

Titanium carbide-nickel aluminide (TiC-Ni x Al y ) intermetallic matrix composite materials were fabricated with additive manufacturing and pressureless melt infiltration for applications intended for high-wear and corrosive environments while maintaining low density. In this work, two compositions of nickel aluminide are infiltrated into porous, printed TiC preforms. Net shaping of a nickel-rich infiltrant is less compared to the net shaping of the aluminum-rich infiltrant due to dissolution of TiC in the molten infiltrant. The microstructures and porosity of the two infiltrants with TiC are examined after processing. The explanation of shape retention from infiltration is explained, and the excellent shape retention in an Al-rich infiltrant system is thought to be from peritectic behavior and a metered infiltration of different phases during cooling and solidification without significant dissolution. The metered infiltration contributed to some porosity, microcracking, and segregated Ni x Al y phases. We show that TiC can be shaped and infiltrated with intermetallics to provide a method of making composites with limited shrinkage and controlled geometry.

36 MATERIALS SCIENCE↗

Preliminary science report on the directional solidification of hypereutectic cast iron during KC-135 low-G maneuvers

An ADSS-P directional solidification furnace was reconfigured for operation on the KC-135 low-g aircraft. The system offers many advantages over quench ingot methods for study of the effects of sedimentation and convection on alloy formation. The directional sodification furnace system was first flown during the September 1982 series of flights. The microstructure of the hypereutectic cast iron sample solidified on one of these flights suggests a low-g effect on graphite morphology. Further experiments are needed to ascertain that this effect is due to low-gravity and to deduce which of the possible mechanisms is responsible for it.

Curreri, P. A.↗

Thermal stability of Cr-Cr 3 Si eutectic microstructures

The thermal stability of Cr-Cr{sub 3}Si lamellar eutectic composites was investigated at temperatures up to 1400 C. In drop-cast Cr-Cr{sub 3}Si, coarsening was found to be interface controlled. The coarsening rate could be reduced by microalloying with Ce and Re, two elements which were chosen because they were expected to segregate to the Cr-Cr{sub 3}Si interfaces. Similarly, directional solidification, which is also expected to lower the Cr-Cr{sub 3}Si interfacial energy, was found to dramatically decrease the coarsening rate.

36 MATERIALS SCIENCE↗

Investigation and simulation of metallic spherules from lunar soils

The microstructure and chemical composition of metallic spherules from the lunar soil were studied by optical, electron-probe, and scanning-electron-microscope techniques. Metallic spherules produced experimentally were compared to the lunar spherules with respect to structure, chemistry, and cooling rates. The structure of the lunar spherules indicates an origin by solidification of molten globules of metal. The spherules are probably produced from both lunar and meteoric sources, the major source being the metal phase present in lunar rocks and soil.

Blau, P. J.↗

Identification of a cast iron alloy containing nonstrategic elements

A program was performed to address the mechanical and environmental needs of Stirling engine heater head and regenerator housing components, while reducing the dependence on strategic materials. An alloy was developed which contained no strategic elemental additions per se. The base is iron with additions of manganese, molybdenum, carbon, silicon, niobium, and ferro-chromium. Such an alloy should be producible on a large scale at very low cost. The resulting alloy, designated as NASAUT 4G-Al, contained 15 Mn, 15 Cr, 2 Mo, 1.5 C, 1.0 Si, 1.0 Nb (in weight percent) with a balance of Fe. This alloy was optimized for chemistry, based upon tensile strength, creep-rupture strength, fracture behavior, and fatigue resistance up to 800 C. Alloys were also tested for environmental compatibility. The microstructure and mechanic properties (including hardness) were assessed in the as-cast condition and following several heat treatments, including one designed to simulate a required braze cycle. The alloy was fabricated and characterized in the form of both equiaxed and columnar-grained castings. The columnar grains were produced by directional solidification, and the properties were characterized in both the longitudinal and transverse orientations. The NASAUT 4G-Al alloy was found to be good in cyclic-oxidation resistance and excellent in both hydrogen and hot-corrosion resistance, especially in comparison to the baseline XF-818 alloy. The mechanical properties of yield strength, stress-rupture life, high-cycle-fatigue resistance, and low-cycle-fatigue resistance were good to excellent in comparison to the current alloy for this application, HS-31 (X-40), with precise results depending in a complex manner on grain orientation and temperature. If required, the ductility could be improved by lowering the carbon content.

Cooper, C. V.↗

Microstructure, mechanical and corrosion behaviors of AlCoCuFeNi-(Cr,Ti) high entropy alloys

The equimolar AlCoCuFeNi-(Cr,Ti) high entropy alloys (HEAs) were synthesized by nonconsumable arc melting to investigate the effects of Cr and Ti on the mechanical and corrosion properties of HEAs. The results showed that as-cast AlCoCuFeNi-(Cr,Ti) HEAs have a multi-phase microstructure, of which the solid-solution face-centered cubic (FCC), body-centered cubic (BCC) phases, and intermetallics can be observed. Ab initio molecular-dynamics (AIMD) simulations exhibit the existence of the preferred short-range ordering of Al-Ni, Co-Cr, Cr-Fe, and Ti-Co pairs in the AlCoCuFeNiCrTi liquid structure. The AIMD simulations are consistent with the experimental observation during solidification. The segregations and the FCC Cu-rich phase appear in the AlCoCuFeNiCrTi alloy, which is in agreement with AIMD calculations. The Cr addition to AlCoCuFeNi facilitates the formation of the BCC phases in the AlCoCuFeNiCr alloy, which can be explained by the larger Ω and smaller δ values. The addition of large Ti atoms facilitates the formation of the FCC phase, which is due to the fact that Ti will easily induce the breakdown of the BCC solid-solution of the AlCoCuFeNi alloy in terms of decreasing the Ω value and increasing the δ value. Finally, the Cr addition improves the corrosion resistance of AlCoCuFeNi alloys.

36 MATERIALS SCIENCE↗