Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHOCK LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Aerothermodynamic heating due to shock wave/laminar boundary-layer interactions in high-enthalpy hypersonic flow

The interaction between a swept shock wave and a laminar boundary layer was investigated experimentally in high-enthalpy hypersonic flow. The effect of high-temperature, real gas physics on the interaction was examined by conducting tests in air and helium. Heat transfer measurements were made on the surface of a flat plate and a shock-generating fin using thin-film resistance sensors for fin incidence angles of 0, 5, and 10 deg at Mach numbers of 6.9 in air and 7.2 in helium. The experiments were conducted in the NASA HYPULSE expansion tube, an impulse-type facility capable of generating high-enthalpy, high-velocity flow with freestream levels of dissociated species that are particularly low. The measurements indicate that the swept shock wave creates high local heat transfer levels in the interaction region, with the highest heating found in the strongest interaction. The maximum measured heating rates in the interaction are order of magnitude greater than laminar flat plate boundary layer heating levels at the same location.

Hackett, Charles M.↗
NASA NTRSDate not supplied

Planar Investigation of a CobraMRV Reentry Flowfield Using Pulse-Burst, Cross-Correlation DGV

The flowfield around a Co-Optimization Blunt-body Reentry Analysis Mid-lift/drag-ratio Rigid Vehicle (CobraMRV) vehicle is investigated with a combination of high-speed planar laser Mie scattering (PLMS) and pulse-burst cross-correlation Doppler global velocimetry (PB-CC-DGV). Tests were conducted in the NASA Langley 4-foot Supersonic Unitary Plan Wind Tunnel (UPWT) over a range of different tunnel operating conditions and model configurations. Results indicate a complex shock-boundary layer interaction. Scalar information extracted from the PLMS show the evolution of the bow shock structure, while streamwise velocity measurements indicate the spatial evolution of the shock-boundary layer interaction including the growth of the separation shock foot and eventual reacceleration of the flow at farther downstream locations. Assessment of multiple cases show strong Mach and Reynolds numbers driven effects on the character of the shock-boundary layer interactions. Measurement uncertainties ranged from 50 to 150 m/s throughout the region of interest, driven largely by angular uncertainties and instabilities in the laser pointing. The mean accuracy of the freestream measurements was found to be 5.2-percent of tunnel predicted values.

Laser↗
NASA NTRS2016

Budget of Turbulent Kinetic Energy in a Shock Wave Boundary-Layer Interaction

Implicit large-eddy simulation (ILES) of a shock wave/boundary-layer interaction (SBLI) was performed. Quantities present in the exact equation of the turbulent kinetic energy transport were accumulated and used to calculate terms like production, dissipation, molecular diffusion, and turbulent transport. The present results for a turbulent boundary layer were validated by comparison with direct numerical simulation data. It was found that a longer development domain was necessary for the boundary layer to reach an equilibrium state and a finer mesh resolution would improve the predictions. In spite of these findings, trends of the present budget match closely with that of the direct numerical simulation. Budgets for the SBLI region are presented at key axial stations. These budgets showed interesting dynamics as the incoming boundary layer transforms and the terms of the turbulent kinetic energy budget change behavior within the interaction region.

shock wave/boundary-layer interaction↗
NASA NTRS1991

Shock wave-boundary layer interactions in rarefied gas flows

A numerical study is presented, using the direct simulation Monte Carlo (DSMC) method, of shock wave-boundary layer interactions in low density supersonic flows. Test cases include two-dimensional, axially-symmetric and three-dimensional flows. The effective displacement angle of the boundary layer is calculated for representative flat plate, wedge, and cone flows. The maximum pressure, shear stress, and heat transfer in the shock formation region is determined in each case. The two-dimensional reflection of an oblique shock wave from a flat plate is studied, as is the three-dimensional interaction of such a wave with a sidewall boundary layer.

Bird, G. A.↗
NASA NTRS1990

Color surface-flow visualization of fin-generated shock wave boundary-layer interactions

Kerosene-lampblack mixtures with addition of a ground colored chalk were used in an experiment on visualizing surface flows of swept shock boundary-layer interactions. The results show that contrasting colors intensify the visualization of different regions of the interaction surface, and help the eye in following the fine streaks to locate the upstream influence. The study confirms observations of the separation occurring at shock strength below accepted values. The superiority of the reported technique over the previous monochrome technique is demonstrated.

Lu, F. K.↗
NASA NTRSDate not supplied

Summary of Shock Wave Turbulent Boundary Layer Interaction Experiments In a Circular Test Section

A series of experiments were performed at Mach 2.5 in a 17 cm diameter circular test section to characterize an impinging/reflected shock wave turbulent boundary layer interaction generated by a cone-cylinder centerbody. The cone-cylinder centerbody generates a conical shock wave that interacts with the naturally occurring boundary layer developing on the test section wall. Three different cone angles were used in the experiment to study unseparated, incipiently separated, and separated interactions. When the cone-cylinder centerbody is positioned on the centerline, a flowfield which is two-dimensional in the mean is generated. Three dimensional interactions were also created by offsetting the cone-cylinder centerbody from the test section centerline. The results are intended to provide benchmark quality datasets for computational fluid dynamics (CFD) validation without the pitfalls inherent in rectangular configurations where corner effects prohibit a truly two-dimensional flow in the mean. The experimental measurements included surface flow visualization, wall static pressure, flowfield Pitot tube pressure, constant-voltage anemometry (CVA) normal hot-wire, and particle image velocimetry (PIV) measurements. The hot-wire measurements were used to calculate mean mass flux and total temperature profiles, mass flux and total temperature turbulence intensities, and the mass flux-total temperature correlation. The PIV measurements provide three-dimensional mean velocity measurements. Agreement between the pressure, hot-wire, and PIV measurements is established in the undisturbed upstream flowfield.

Supersonic↗
NASA NTRSDate not supplied

Summary of Shock Wave Turbulent Boundary Layer Interaction Experiments in a Circular Test Section

A series of experiments were performed at Mach 2.5 in a 17 cm diameter circular test section to characterize an impinging/reflected shock wave turbulent boundary layer interaction generated by a cone-cylinder centerbody. The cone-cylinder centerbody generates a conical shock wave that interacts with the naturally occurring boundary layer developing on the test section wall. Three different cone angles were used in the experiment to study unseparated, incipiently separated, and separated interactions. When the cone-cylinder centerbody is positioned on the centerline, a flowfield which is two-dimensional in the mean is generated. Three dimensional interactions were also created by offsetting the cone-cylinder centerbody from the test section centerline. The results are intended to provide benchmark quality datasets for computational fluid dynamics (CFD) validation without the pitfalls inherent in rectangular configurations where corner effects prohibit a truly two-dimensional flow in the mean. The experimental measurements included surface flow visualization, wall static pressure, flowfield Pitot tube pressure, constant-voltage anemometry (CVA) normal hot-wire, and particle image velocimetry (PIV) measurements. The hot-wire measurements were used to calculate mean mass flux and total temperature profiles, mass flux and total temperature turbulence intensities, and the mass flux-total temperature correlation. The PIV measurements provide three-dimensional mean velocity measurements. Agreement between the pressure, hot-wire, and PIV measurements is established in the undisturbed upstream flowfield.

compressible flow↗
NASA NTRS1976

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetimes for the two flows. It is proposed that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Mikulla, V.↗
NASA NTRS1976

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetime for the two flows. We propose that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Mikulla, V.↗
NASA NTRS1993

Aerodynamic heating in the vicinity of hypersonic, axisymmetric, shock-wave boundary-layer interactions

Aerodynamic heating rates are calculated from time-dependent temperature measurements in the vicinity of shock-wave boundary-layer interactions due to conical compression ramps on an axisymmetric body. The data were acquired at the Ohio State University Aeronautical and Astronautical Research Laboratory and at the Air Force Flight Dynamics Laboratory at Mach numbers of 6 and 10. The model is a cylindrical body with a 10 deg conical nose. Conical ramps with half-angles of 10, 20, 25, 30, and 35 deg serve as shock-wave generators. Flowfield surveys are made in the vicinity of the ramp vertices, separation points, and reattachment points. Experimental results quantify temperature response and the resulting heat transfer rates as a function of ramp angle, Reynolds number and freestream Mach number. The temperature responses within the flowfield appear to be steady-state for all angles and all Reynolds numbers, and hence, the heat transfer rates appear to be steady-state.

Flanagan, M. J., Jr.↗
NASA NTRS1972

Prediction and measurement of heat transfer rates for the shock-induced unsteady laminar boundary layer on a flat plate

The unsteady laminar boundary layer induced by the flow-initiating shock wave passing over a flat plate mounted in a shock tube was theoretically and experimentally studied in terms of heat transfer rates to the plate for shock speeds ranging from 1.695 to 7.34 km/sec. The theory presented by Cook and Chapman for the shock-induced unsteady boundary layer on a plate is reviewed with emphasis on unsteady heat transfer. A method of measuring time-dependent heat-transfer rates using thin-film heat-flux gages and an associated data reduction technique are outlined in detail. Particular consideration is given to heat-flux measurement in short-duration ionized shocktube flows. Experimental unsteady plate heat transfer rates obtained in both air and nitrogen using thin-film heat-flux gages generally agree well with theoretical predictions. The experimental results indicate that the theory continues to predict the unsteady boundary layer behavior after the shock wave leaves the trailing edge of the plate even though the theory is strictly applicable only for the time interval in which the shock remains on the plate.

Cook, W. J.↗
NASA NTRS1975

Calculation of shock-separated turbulent boundary layers

Numerical solutions of the complete, time-averaged conservation equations using several eddy-viscosity models for the Reynolds shear stress to close the equations are compared with experimental measurements in a compressible, turbulent separated flow. An efficient time-splitting, explicit difference scheme was used to solve the two-dimensional conservation equations. The experiment used for comparison was a turbulent boundary layer that was separated by an incident shock wave in a Mach 2.93 flow with a unit Reynolds number of 5.7 x 10 to the seventh power m. Comparisons of predicted and experimental values of surface pressure, shear stress along the wall, and velocity profiles are shown. One of the tested eddy-viscosity models which allows the shear stress to be out of equilibrium with the mean flow produces substantially better agreement with the experimental measurements than the simpler models. A tool is thereby provided for inferring additional information about the flow, such as static pressures in the stream, which might not be directly obtainable from experiments.

Baldwin, B. S.↗
NASA NTRS1975

Control of shock-wave boundary-layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation has been conducted to determine the effect of bleed region geometry and bleed rate on shock wave-boundary layer interactions in an axisymmetric, mixed-compression inlet at a Mach number of 2.5. The full realizable reduction in transformed form factor is obtained by bleeding off about half the incident boundary layer mass flow. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise. Slanted holes are more effective than normal holes. Two different bleed hole sizes were tested without detectable difference in performance.

Fukuda, M. K.↗
NASA NTRS1995

Reduction of fluctuating pressure loads in shock wave turbulent boundary layer interactions

Fluctuating surface pressure measurements have been made to investigate the effectiveness of boundary layer separators (BLS's) in reducing the fluctuating pressure loads produced by separated shock wave turbulent boundary layer interactions. Measurements have been made under unswept and swept compression corner interactions in a Mach 5 flow. BLS's fix the separation location and eliminate the large-amplitude, low-frequency fluctuating pressure loads upstream of the compression corners. The loads on the unswept compression corner face are reduced by as much as 59%. The BLS's also shift the mean pressure distribution on the unswept corner face in the streamwise direction. Results show that the loads on the corner face vary with the BLS height and the distance between the BLS and the compression corner. Suggestions for the optimum placement and the use of the BLS's are also made.

Barter, John W.↗
NASA NTRS1976

Shock wave/turbulent boundary-layer interactions with and without surface cooling

An experimental investigation was conducted to delineate the structure of the flowfield and temperature distributions in a shock wave/turbulent boundary-layer interaction with and without surface cooling. The Mach number upstream was about 3.5, and the wave angle was 23 deg. The wall to stagnation temperature ratio was 0.44 with cooling and 1.1 with heating. A detailed map of the interaction flowfields deduced from numerous boundary-layer traversing stations revealed the influence of wall cooling on the flowfield, wave structure, and size of the flow separation region. With surface cooling, the size of the separation region was much smaller, and the separation and reflected shock waves merged together near the edge of the velocity boundary layer, extending into the freestream as one wave.

Back, L. H.↗
NASA NTRS1952

On Reflection of Shock Waves from Boundary Layers

Measurements are presented at Mach numbers from about 1.3 to 1.5 of reflection characteristics and the relative upstream influence of shock waves impinging on a flat surface with both laminar and turbulent boundary layers. The difference between impulse and step waves is discussed and their interaction with the boundary layer is compared. General considerations on the experimental production of shock waves from wedges and cones and examples of reflection of shock waves from supersonic shear layers are also presented.

Liepmann, H W↗