Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Graphene milling dynamics during helium ion beam irradiation

We explore the potential of the Helium Ion Microscope (HIM) as a tool for direct-write patterning of graphene and describe the underlying processes of graphene milling with image data processing. Controlled helium ion irradiation of suspended graphene conducted while monitoring the mill in-situ revealed the localized formation of nanopores, their growth, and coalescence. We also explore the effects of defects on the milling dynamics, and show that pre-exposed membranes rupture by cracking and rapid crack propagation at the edges of the growing defects. The mechanism for the rupturing process is described by local defect formation by excessive irradiation of helium ions, dictated by the scanning direction of the beam. As a result, these findings enrich fundamental understanding of the graphene milling process with a helium ion beam that, is necessary for high-resolution and high throughput patterning of graphene with nanoscale precision.

36 MATERIALS SCIENCE↗

Combustion characteristics of nanoaluminum, liquid water, and hydrogen peroxide mixtures

An experimental investigation of the combustion characteristics of nanoaluminum (nAl), liquid water (H{sub 2}O{sub (l)}), and hydrogen peroxide (H{sub 2}O{sub 2}) mixtures has been conducted. Linear and mass-burning rates as functions of pressure, equivalence ratio ({phi}), and concentration of H{sub 2}O{sub 2} in H{sub 2}O{sub (l)} oxidizing solution are reported. Steady-state burning rates were obtained at room temperature using a windowed pressure vessel over an initial pressure range of 0.24 to 12.4 MPa in argon, using average nAl particle diameters of 38 nm, {phi} from 0.5 to 1.3, and H{sub 2}O{sub 2} concentrations between 0 and 32% by mass. At a nominal pressure of 3.65 MPa, under stoichiometric conditions, mass-burning rates per unit area ranged between 6.93 g/cm{sup 2} s (0% H{sub 2}O{sub 2}) and 37.04 g/cm{sup 2} s (32% H{sub 2}O{sub 2}), which corresponded to linear burning rates of 9.58 and 58.2 cm/s, respectively. Burning rate pressure exponents of 0.44 and 0.38 were found for stoichiometric mixtures at room temperature containing 10 and 25% H{sub 2}O{sub 2}, respectively, up to 5 MPa. Burning rates are reduced above {proportional_to}5 MPa due to the pressurization of interstitial spaces of the packed reactant mixture with argon gas, diluting the fuel and oxidizer mixture. Mass burning rates were not measured above {proportional_to}32% H{sub 2}O{sub 2} due to an anomalous burning phenomena, which caused overpressurization within the quartz sample holder, leading to tube rupture. High-speed imaging displayed fingering or jetting ahead of the normal flame front. Localized pressure measurements were taken along the sample length, determining that the combustion process proceeded as a normal deflagration prior to tube rupture, without significant pressure buildup within the tube. In addition to burning rates, chemical efficiencies of the combustion reaction were determined to be within approximately 10% of the theoretical maximum under all conditions studied. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The anodic surface film and hydrogen evolution on Mg

This paper clarifies that the inner and outer layers of the anodic film consist of a nano/micro-porous MgO+Mg(OH) 2 mixture. The film becomes thicker and more porous with increasing potential. It can rupture when potential is too positive in a non-corrosive Mg(OH) 2 solution. Hydrogen evolution becomes more intensive as polarization potential increases, particularly when the potential at the film-covered Mg surface is close to or more positive than the hydrogen equilibrium potential, suggesting that an “anodic hydrogen evolution” (AHE) reaction occurs on the substrate Mg in film pores, and the significantly intensified AHE causes film rupture at high potential.

36 MATERIALS SCIENCE↗

A method for predicting failure statistics for steady state elevated temperature structural components

This paper presents the initial development of a high temperature life prediction method that accounts for the variability in the material properties of Grade 91 steel. The method accounts for material variability by fitting a variable 3-parameter Weibull distribution to experimental rupture data and accounts for the variability of creep deformation on the steady-state stresses via a Monte Carlo approach. To ensure reasonable computational times, the model represents the material as an extremely viscous Stokes fluid with a non-Newtonian viscosity, therefore solving the stress relaxation problem with a steady, static, instead of transient, analysis. Furthermore, the complete statistical analysis combines this model for creep deformation with a probabilistic model for creep rupture to evaluate the probability of premature failure for a set of sample problems, comparing the predicted failure statistics to the design life predicted by the ASME Boiler and Pressure Vessel Code rules.

42 ENGINEERING↗

A probabilistic creep model incorporating test condition, initial damage, and material property uncertainty

Uncertainty is prevalent in the creep resistance of alloys, where at elevated temperature and low pressure, rupture can range across logarithmic decades. In this study, a probabilistic continuum-damage-mechanics (CDM)-based model is derived to capture the uncertainty of creep resistance. To meet this objective, creep data for alloy 304 Stainless Steel is gathered. A constitutive model, “Sinh”, is calibrated deterministically to determine the statistical variability of the material properties. Three sources of uncertainty are injected into the model: test condition (stress and temperature), initial damage, and material properties. Probabilistic simulations are carried out by (a) calibrating probability distribution functions (pdfs) for each source of uncertainty (b) randomly sampling the pdfs using Monte Carlo methods and (c) executing simulations to replicate the uncertain creep behavior. A sensitivity analysis is performed to evaluate the relative effect of each source of uncertainty. In full probabilistic simulations, the cumulative uncertainty of creep behavior is evaluated. The probabilistic model accurately predicts the creep deformation and rupture of the available experiments. The probabilistic model is validated for interpolation but lacks extrapolation ability. Several future works are proposed to further improve the model.

36 MATERIALS SCIENCE↗

Catalytic routes and oxidation mechanisms in photoreforming of polyols

Photocatalytic reforming of biomass-derived oxygenates leads to H 2 generation and evolution of CO 2 via parallel formation of organic intermediates through anodic oxidations on a Rh/TiO 2 photocatalyst. The reaction pathways and kinetics in the photoreforming of C 3 –C 6 polyols were explored. Polyols are converted via direct and indirect hole transfer pathways resulting in (i) oxidative rupture of C–C bonds, (ii) oxidation to a-oxygen functionalized aldoses and ketoses (carbonyl group formation) and (iii) light-driven dehydration. Direct hole transfer to chemisorbed oxygenates on terminal Ti(IV)-OH groups, generating alkoxy-radicals that undergo ß-C–C-cleavage, is proposed for the oxidative C–C rupture. Carbonyl group formation and dehydration are attributed to indirect hole transfer at surface lattice oxygen sites [Ti_ _ _O_ _ _Ti] followed by the generation of carbon-centered radicals. Polyol chain length impacts the contribution of the oxidation mechanisms favoring the C–C bond cleavage (internal preferred over terminal) as the dominant pathway with higher polyol carbon number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multiscale modelling of evolving foams

We present a set of multi-scale interlinked algorithms to model the dynamics of evolving foams. These algorithms couple the key effects of macroscopic bubble rearrangement, thin film drainage, and membrane rupture. For each of the mechanisms, we construct consistent and accurate algorithms, and couple them together to work across the wide range of space and time scales that occur in foam dynamics. These algorithms include second order finite difference projection methods for computing incompressible fluid flow on the macroscale, second order finite element methods to solve thin film drainage equations in the lamellae and Plateau borders, multiphase Voronoi Implicit Interface Methods to track interconnected membrane boundaries and capture topological changes, and Lagrangian particle methods for conservative liquid redistribution during rearrangement and rupture. We derive a full set of numerical approximations that are coupled via interface jump conditions and flux boundary conditions, and show convergence for the individual mechanisms. We demonstrate our approach by computing a variety of foam dynamics, including coupled evolution of three-dimensional bubble clusters attached to an anchored membrane and collapse of a foam cluster.

97 MATHEMATICS AND COMPUTING↗

Effect of stress evolution on microstructural behavior in U-Mo/Al dispersion fuel [Effect of stress on microstructural evolution in U-Mo/Al dispersion fuel]

U-Mo/Al dispersion fuel irradiated to high burnup at high power (high fission rate) exhibited microstructural changes such as deformation of the fuel particles, pore growth, and rupture of the Al matrix. The driving force for these microstructural changes was meat swelling caused by a combination of fuel particle swelling and interaction layer growth. Five miniplates with well-recorded fabrication data and irradiation conditions were selected, and their PIE data was analyzed. ABAQUS finite element analysis (FEA) was utilized to simulate the microstructural evolution of the plates. Using the simulation results shear stress, effective stress and hydrostatic stress exerted on both the fuel particles and the Al matrix were determined. The effects of fabrication and irradiation variables on stress-induced microstructural evolutions, such as pore growth in the interaction layers and Al matrix rupture, were investigated. The observed microstructural changes were consistent with the calculated stress distribution in the meat.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiation Damages of Structural Materials under Different Irradiation Environments

For the advancement and development of nuclear systems used in heavy irradiation environments such as fusion DEMO reactors, fission reactors, fast reactors, and accelerator driven target systems, it is necessary to fully understand the changes of mechanical properties and the other properties of the materials induced by irradiation and to clarify the synergistic effect of displacement damage and helium generation. In this study the mechanical property changes and microstructural development induce by displacement damage and helium production have been mainly examined in austenitic stainless steels, 316FR and type304, and ferritic/martensitic steel, HCM12A, irradiated at around 550oC in JRR-3M reactor and/or JOYO fast reactor. At 550°C, 316FR steel was superior to 304 steel in terms of the amount of ductility and strength with respect to irradiation resistance. It is noteworthy that at 550 °C as well as room temperature, the higher fracture strength of the 316FR steels is a remarkable result. It is found that helium atoms strongly influenced on creep lifetime of the irradiated austenitic stainless steel, 316FR. It was found that the ratio of creep rupture time is slightly lower than the lower limit of previous study’s Miyaji and co-workers in the region from 0.01 appm to 1 appm. It is also found that the lower limit of reduction ratio of creep rupture time (irradiation specimen to unirradiation one) does not decrease linearly with the helium production above 10 appm up to about 33 appm. dpa enhanced the reduction of creep lifetime. Recent R&D of high-energy accelerator driven target systems used under heavy irradiation environment is also introduced and discussed for high radiation resistance materials such as Ti alloys with very high number density of nano size precipitate, which have been studying under RaDIATE collaboration, from points of view of irradiation damage and materials development.

radiation damage, structural alloys, neutron irrad↗

Creep behavior of an additively manufactured 9Cr steel in the as-built condition

Limited studies have evaluated the creep behavior of additively manufactured (AM) ferritic-martensitic (FM) steels. This work investigated the creep behavior of a 9Cr FM steel fabricated by powder blown directed energy deposition (DED) technique. Here, the creep testing at 550–650 °C and 150 MPa for the specimens along the deposition direction in the as-built condition, together with corresponding microstructural characterization, revealed a threshold temperature between 600 and 625 °C, below which the steel has creep resistance comparable with Grade 91 cross-welds and noticeably greater than 9Cr-1Mo steel. The threshold temperature distinguishes the creep behavior in two regimes differentiated in creep activation energy, creep deformation, and failure mechanism. Unlike the creep rupture surface ~45° from the loading direction when tested above the threshold temperature, the creep rupture for testing below the threshold temperature resembles type IV failure in the cross-welds of ferritic steels. The DED-induced layer structure in the as-built steel played a significant role on the change of creep behavior.

36 MATERIALS SCIENCE↗

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗

Studies on densification, mechanical, micro-structural and structure–properties relationship of magnesium aluminate spinel refractory aggregates prepared from Indian magnesite

The present work intends to study the development of magnesium aluminate spinel aggregates from Indian magnesite in a single firing stage. The raw magnesite has been evaluated in terms of chemical analysis, differential thermal analysis, thermogravimetric analysis, infrared spectroscopy, and X-ray diffraction. The experimental batch containing Indian magnesite and calcined alumina has been sintered in the temperature range of 1550 °C–1700 °C. The sintered material has been characterized in terms of physico-chemical properties like bulk density, apparent porosity, true density, relative density and thermo-mechanical/mechanical properties like hot modulus of rupture, thermal shock resistance, cold modulus of rupture and structural properties by X-ray diffraction in terms of phase identification and evaluation of crystal structure parameters of corresponding phases by Rietveld analysis. The microstructures developed at different temperatures have been analyzed by field emission scanning electron microscope study and compositional analysis of the developed phase has been carried out by energy dispersive X-ray study. - Highlights: • The studies have been done to characterize the developed magnesium aluminate spinel. • The studies reveal correlation between refractory behavior of spinel and developed microstructures. • The studies show the values of lattice parameters of developed phases.

36 MATERIALS SCIENCE↗

Microstructure characterization of recycled IN718 powder and resulting laser clad material

Highlights: • A simple and efficient recycling procedure of IN718 powder has been defined for the laser cladding process. • Characterization of wasted and cleaned powder and comparison with new IN718 powder pointed out a slight diameter increase. • Microstructure characterization of clad builds showed differences between builds with new and recycled powders. • Clad microstructure and porosity increase remain constant static properties but decrease rupture strain after 3 reuses. • Without special precautions for cladding, the recycled powder can be reused twice without modifying the properties of IN718. - Abstract: The possibility to reuse the metal powder wasted in Laser Material Deposition (LMD) process has been evaluated and a simple procedure developed. LMD uses metal powder which is fed through a nozzle into the focal point of a laser, where it melts the powder and the substrate material. During the process, a high ratio of particles hits against an unmelted area and directly bounces off the deposited area. The efficiency ratio of deposition can drop to 40% depending on the configuration and spot size. This work deals with the design of a procedure to recollect and reuse the wasted powder of a nickel based superalloy IN718. After usage, powder is recollected, undesired fractions are magnetically segregated and aggregates are removed by sieving. The particles are mixed again and ready for reuse. In order to study the effectiveness of the process, no new powder has been added to the recovered fraction, and this procedure has been repeated five times. Experimental tests show that deposited material present similar properties than those obtained with new powder grains. But, after 3 reuses, the porosity content increases consequently and the rupture strain decreases strongly. The implementation of this process allows the improvement of the final efficiency, reducing costs and decreasing the hazardous powder amount.

36 MATERIALS SCIENCE↗

Microstructure control to improve creep strength of alumina-forming austenitic heat-resistant steel by pre-strain

Highlights: • The effect of pre-strain on creep strength of AFA steel was studied. • The creep test was performed at 700°C and 200Mpa, and the aging test was carried out using box furnace at 700°C to simulate the microstructural evolution during creep. • Microstuctural evolution was observed by using SEM, EBSD, and TEM to investigate the relationship between creep strength and microstructure. - Abstract: At 700 °C and 200 MPa, the creep rupture time of W-containing alumina-forming austenitic heat-resistant (WAFA) steel increases from 1044 to 3119 h by pre-strain. Pre-strain introduces a lot of dislocation into the matrix and most of the dislocations remain stable to the end of creep without recovery and recrystallization. In addition, the dislocations have enabled secondary NbC and Laves phase to be uniformly distributed and refined. However, the dislocations lower grain boundary strength due to the coarsening of precipitates along grain boundaries Therefore, the increase in the creep rupture time in spite of deterioration of grain boundary strength is attributed to the dislocation strengthening and enhanced precipitation hardening within grains.

36 MATERIALS SCIENCE↗

Susceptibility weighted MRI pinpoints spontaneous intracerebral hemorrhage in stroke-prone spontaneously hypertensive rats

Purpose: To find magnetic resonance imaging (MRI) precursors of spontaneous intracerebral hemorrhage in stroke-prone spontaneously hypertensive rats (SHRSP). Method: SHRSP rats were used with both a low/high salt (n = 18 or 11) Japanese diet and salty drinking water to generate spontaneous intracerebral hemorrhage (ICH). Various MRI sequences, and in particular, susceptibility weighted imaging (SWI), were used and combined with a gadolinium (Gd) contrast agent or oxygen gas to identify the rupture of the blood brain barrier (BBB) and the temporal ICH. Results: Most rats developed hypertensive ICH stroke in the high salt group during the 10–13 week period compared to only one third of rats in the low salt group during the 14–18 week period. The location of stroke for both the low/high-salt groups was highest in the striatum (58%/43%), followed by the cortex (21%/30%). The edematous enhancement on T2 weighted (T2W) imaging or Gd based T1 weighted (Gd-T1W) imaging due to the ruptured BBB preceded the striatal hemorrhages seen on SWI. The most recent bleeds were observed on temporal SWI or on oxygen-enhanced SWI. The mode of the volume of bleeds was 0.4 mm 3 . A positive correlation between susceptibility x volume and R2* x volume of the bleeds was observed. Conclusions: SHRSP rats with the high salt diet effectively generated a hypertensive hemorrhagic stroke which could be monitored by various MRI sequences. The venous dilation on SWI may precede any abnormality on T2W or Gd-T1W imaging. The edematous enhancement on T2W or Gd-T1W indicated a BBB breakdown that may precede striatal ICH by several days. This suggests the need for immediate treatment to improve outcome if this finding is observed. Here, the use of oxygen with SWI was able to help differentiate old bleeds from very recent bleeds.

60 APPLIED LIFE SCIENCES↗

Effects of Alloying and Processing Modifications on Precipitation Behavior and Elevated Temperature Strength in 9% Cr Ferritic/Martensitic Steels

Two low-carbon 9-Cr ferritic-martensitic steels were designed here with the aim of decreasing M 23 C 6 and maintaining or increasing MX phase fraction. A low-carbon (LC) alloy and a low-carbon, zero-niobium (0 Nb) alloy were fabricated, their designs based upon the P92 alloy system. Solutionizing temperatures to maximize V and Nb in solution while avoiding δ-ferrite were determined to be 1170 °C for the P92 alloy and 1050 °C for LC and 0 Nb, significantly lower than predicted using ThermoCalc ® modelling. As was intended, the M 23 C 6 phase fraction was reduced for LC and 0 Nb alloys after both heat treating and aging relative to the base P92 alloy, as determined by wide angle x-ray scattering (WAXS) analysis. Dislocation density measurements from x-ray line broadening in P92 and LC suggest these alloys had more stable dislocation substructures than 0 Nb at lower temperature and shorter time aging conditions. While LC exhibited lower microhardness than P92 at room temperature, the tensile properties were comparable at 650 °C, suggesting that elevated temperature strength can be achieved with lower carbon contents. Aging studies showed that P92 had a more stable microstructure for higher temperature and longer time aging conditions. The P92 alloy also had a longer stress rupture life, implying that the M 23 C 6 precipitate contribution to thermal stability is important. Evidence of Z-phase was discovered for the LC alloy aged 10,000 h at 650 °C, corresponding to decreased strength and increased ductility. Overall, the stress rupture lives of the modified heat-treatment variations of P92 and LC compare favorably to literature values for 9% Cr steels with conventional heat treatments.

36 MATERIALS SCIENCE↗

Experimental evaluation of localized creep deformation in grade 91 steel weldments

Spatially resolved measurement of localized creep deformation in heterogeneous creep resistant steel weldments is crucial but challenging for lifetime assessments of critical steam components in power plants. Here, experimental approaches were established to quantitatively evaluate commonly observed localized creep deformation in multi-pass Grade 91 steel weldments. An in-situ digital image correlation (DIC) system was utilized with a creep testing frame to monitor and measure both full-field strain and localized strain accumulation across the weldments during long-term creep testing at elevated temperatures. The in situ DIC method measured not only the creep deformation behavior of the weld metal, heat affected zone (HAZ), and base metal, but also creep strain evolution for each sub-region within the HAZ itself, including coarse-grained HAZ, fine-grained HAZ (FGHAZ), and intercritical HAZ (ICHAZ). The DIC results revealed that local creep strain in the ICHAZ reached up to 90% strain before final rupture, whereas nominal creep strain measured by the standard extensometer of the tested cross-weld specimen was below 10%, indicative of Type IV cracking of the Grade 91 weld. Microstructural analyses revealed that the faster creep degradation/deformation in the HAZ was caused mainly by accelerated matrix grain recrystallization/growth and a reduced pinning effect from the segregated and coarsened precipitates in the FGHAZ and ICHAZ. The ultimate creep rupture occurred in the ICHAZ owing to its lowest creep resistance induced by the largest recrystallized grain size, the lowest fraction of coincidence site lattice, and the lowest local strain energies/dislocation densities.

36 MATERIALS SCIENCE↗