Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Materials Compatibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Compatibility Assessment of Advanced Stainless Steels in Sodium

Type 316L stainless steel capsules containing commercially pure sodium and miniature tensile specimens of HT-UPS (austenitic, 14Cr-16Ni), NF-616 (ferritic/martensitic, 9Cr-2W-0.5Mo), or 316L (austenitic, 17Cr-10Ni-2Mo) stainless steel were exposed at 600 or 700 C for 100 and 400 h as a screening test for compatibility. Using weight change, tensile testing, and metallographic analysis, HT-UPS and 316L were found to be largely immune to changes resulting from sodium exposure, but NF-616 was found susceptible to substantial decarburization at 700 C. Subsequently, two thermal convection loops (TCLs) constructed of 316L and loaded with commercially pure sodium and miniature tensile specimens of HT-UPS and 316L were operated for 2000 h each one between 500 and 650 C, the other between 565 and 725 C at a flow rate of about 1.5 cm/s. Changes in specimen appearance, weight, and tensile properties were observed to be very minor in all cases, and there was no metallographic evidence of microstructure changes, composition gradients, or mass transfer resulting from prolonged exposure in a TCL. Thus, it appears that HT-UPS and 316L stainless steels are similarly compatible with commercially pure sodium under these exposure conditions.

36 MATERIALS SCIENCE↗

Identification of High Performance, Low Environmental Impact Materials and Processes Using Systematic Substitution (SyS)

Process analysis can identify opportunities for efficiency improvement including cost reduction, increased safety, improved quality, and decreased environmental impact. A thorough, systematic approach to materials and process selection is valuable in any analysis. New operations and facilities design offer the best opportunities for proactive cost reduction and environmental improvement, but existing operations and facilities can also benefit greatly. Materials and processes that have been used for many years may be sources of excessive resource use, waste generation, pollution, and cost burden that should be replaced. Operational and purchasing personnel may not recognize some materials and processes as problems. Reasons for materials or process replacement may include quality and efficiency improvements, excessive resource use and waste generation, materials and operational costs, safety (flammability or toxicity), pollution prevention, compatibility with new processes or materials, and new or anticipated regulations.

Dhooge, P. M.↗

Improved treatment of multi-material cells in thermal radiation transport codes

High-energy-density physics simulations with non-conformal meshes of materials require a multi-material (MM) closure that affects the thermal radiation transport (TRT). We propose a set of novel closures that work for an arbitrary number of materials, both grey and multigroup energy discretizations, and any angular discretization (such as Sn, IMC, or diffusion). For each spatial cell, our closures let each species (ion and electron) of each material have its own temperature, density, and internal energy, but use a single radiation distribution that interacts with all materials within the cell. Our closures maintain energy conservation, do not incur increased computational cost in the TRT solve itself, are compatible with single-material TRT solvers, and do not make any temperature-equilibrium assumptions. Here we test our closures on a wide range of increasingly realistic problems and find them to be robust.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Durability of ionomer encapsulants in photovoltaic modules

Ethylene vinyl acetate (EVA) has for decades been the preferred material for photovoltaic (PV) module encapsulation. However, while it is relatively inexpensive and initially adheres well to module components, EVA discolors with age and - as interfacial adhesion degrades - becomes susceptible to delamination, ultimately resulting in reduced module efficiency and shortened service lifetimes. As potential replacements for EVA, ionomer thermoplastic materials cure faster, are more resistant to discoloration and potential induced degradation, and do not evolve corrosive acetic acid, making them compatible with new device materials such as perovskites. Since there is limited information on ionomer durability for PV module applications, a series of field and accelerated laboratory aging studies were conducted to assess ionomer interface stability in the presence of terrestrial environmental stressors. It is shown that adhesion to the glass and cell interfaces of PV modules is inferior to EVA, both before and after aging, rendering ionomers particularly susceptible to delamination after short timeframes. Potential solutions to improve ionomer adhesion are discussed.

14 SOLAR ENERGY↗

Trends in Materials' Outgassing Technology

Test sample acquisition and chemical analysis techniques for outgassing products from spacecraft, experiment modules, and support equipment is described. The reduction of test data to a computer compatible format to implement materials selection policies is described. A list of the most troublesome outgassing species is given and several materials correlations are discussed. Outgassing from solar panels, thermal blankets, and wire insulation are examined individually.

Colony, J. A.↗

Manufacturing and NDE of Large Composite Aerospace Structures at MSFC

NASA's vision for transportation to orbit calls for new vehicles built with new materials technology. The goals of this new launch system development are to improve safety, dramatically reduce cost to orbit, and improve vehicle turn around time. Planned Space Shuttle upgrades include new reusable liquid propellant boosters to replace the solid propellant boosters. These boosters are to have wings and return to the launch site for a horizontal landing on an airport runway. New single and two stages to orbit concepts are being investigated. To reduce weight and improve performance composite materials are proposed for fuel and oxidizer tanks, fuel feedlines, valve bodies, aerostructures, turbomachinery components. For large composite structures new methods of fabrication are being proposed and developed. Containment of cryogenic fuel or oxidizer requires emphases on composite material densification and chemical compatibility. Ceramic matrix and fiber composites for hot rotating turbomachinery have been developed with new fabrication processes. The new requirements on the materials for launcher components are requiring development of new manufacturing and inspection methods. This talk will examine new and proposed manufacturing methods to fabricate the revolutionary components. New NDE methods under consideration include alternative X-ray methods, X-ray laminagraphy, advanced CT, Thermography, new ultrasonic methods, and imbedded sensors. The sizes, complexity, use environment, and contamination restrictions will challenge the inspection process. In flight self-diagnosis and rapid depot inspection are also goals of the NDE development.

Whitaker, Ann↗

Investigation of Compatibility Between M-Cr-Al-X Thermal Spray Coatings and Third Generation γ-TiAl Alloys

In this work, the physical and chemical compatibility of cast Ti-Al-Nb-Cr-Zr and Ti-Al-Nb-Cr-Zr-B-La alloys was investigated with oxidation-resistant M-Cr-Al-X thermal spray coatings. Ti and Al are main alloy elements to form γ-TiAl and α{sub 2}-Ti{sub 3}Al phases. To obtain coatings, we used air plasma spray and high-velocity oxygen fuel equipment. Four commercially available M-Cr-Al-X powders, including Ta-containing, were used as starting materials. Our investigation of compatibility between M-Cr-Al-X thermal spray coatings and γ-TiAl alloys consists of isothermal annealing in air muffle furnace during 100 h at 920 °C, followed by samples investigation. Oxidation products formed at coatings surface were studied by XRD analysis with Rietveld refinement. Interdiffusion between coatings and alloys was studied by means of cross-sectional SEM with EDX analysis. Plots were made to show concentration of each main element at the end of experiments. Samples were subjected to dynamic mechanical thermal analysis in order to determine the effect of high-temperature exposure on complex elastic modulus. Finally, burner rig cycling test was performed to estimate the thermal shock resistance of M-Cr-Al-X coatings.

36 MATERIALS SCIENCE↗

An evaluation of complementary approaches to elucidate fundamental interfacial phenomena driving adhesion of energetic materials

In this study, cohesive Hamaker constants of solid materials are measured via optical and dielectric properties (i.e., Lifshitz theory), inverse gas chromatography (IGC), and contact angle measurements. To date, however, a comparison across these measurement techniques for common energetic materials has not been reported. This has been due to the inability of the community to produce samples of energetic materials that are readily compatible with contact angle measurements. Here we overcome this limitation by using physical vapor deposition to produce thin films of five common energetic materials, and the contact angle measurement approach is applied to estimate the cohesive Hamaker constants and surface energy components of the materials. The cohesive Hamaker constants range from 85 zJ to 135 zJ across the different films. When these Hamaker constants are compared to prior work using Lifshitz theory and nonpolar probe IGC, the relative magnitudes can be ordered as follows: contact angle > Lifshitz > IGC. Furthermore, the dispersive surface energy components estimated here are in good agreement with those estimated by IGC. Due to these results, researchers and technologists will now have access to a comprehensive database of adhesion constants which describe the behavior of these energetic materials over a range of settings.

36 MATERIALS SCIENCE↗

Environmentally compatible hand wipe cleaning solvents

Several solvents of environmental concern have previously been used for hand wipe cleaning of SRB surfaces, including 1,1,1-trichloroethane, perchloroethylene, toluene, xylene, and MEK. USBI determined the major types of surfaces involved, and qualification requirements of replacement cleaning agents. Nineteen environmentally compatible candidates were tested on 33 material substrates with 26 types of potential surface contaminants, involving over 7,000 individual evaluations. In addition to the cleaning performance evaluation, bonding, compatibility, and corrosion tests were conducted. Results showed that one cleaner was not optimum for all surfaces. In most instances, some of the candidates cleaned better than the 1,1,1-trichloroethane baseline control. Aqueous cleaners generally cleaned better, and were more compatible with nonmetallic materials, such as paints, plastics, and elastomers. Organic base cleaners were better on metal surfaces. Five cleaners have been qualified and are now being implemented in SRB hand wipe cleaning operations.

Clayton, Catherine P.↗

Heterogeneous dislocation loop formation near grain boundaries in a neutron-irradiated commercial FeCrAl alloy

FeCrAl alloys are an attractive materials class for nuclear power applications due to their increased environmental compatibility over more traditional nuclear materials. Preliminary studies into the radiation tolerance of FeCrAl alloys under accelerated neutron testing between 300-400 °C have shown post-irradiation microstructures containing dislocation loops and Cr-rich ' phase. Although these initial works established the post-irradiation microstructures, little to no focus was applied towards the influence of pre-irradiation microstructures on this response. Here, a well annealed commercial FeCrAl alloy, Alkrothal 720, was neutron irradiated to 1.8 dpa at 382 °C and then the role of random high angle grain boundaries on the spatial distribution and size of dislocation loops, dislocation loops, and black dot damage was analyzed using on-zone scanning transmission electron microscopy. Results showed a clear heterogeneous dislocation loop formation with dislocation loops showing an increased number density and size, black dot damage showing a significant number density decrease, and an increased size of dislocation loops in the vicinity directly adjacent to the grain boundary. Lastly, these results suggest the importance of the pre-irradiation microstructure on the radiation tolerance of FeCrAl alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Physical and chemical test results of electrostatic safe flooring materials

This test program was initiated because a need existed at the Kennedy Space Center (KSC) to have this information readily available to the engineer who must make the choice of which electrostatic safe floor to use in a specific application. The information, however, should be of value throughout both the government and private industry in the selection of a floor covering material. Included are the test results of 18 floor covering materials which by test evaluation at KSC are considered electrostatically safe. Tests were done and/or the data compiled in the following areas: electrostatics, flammability, hypergolic compatibility, outgassing, floor type, material thickness, and available colors. Each section contains the test method used to gather the data and the test results.

Gompf, R. H.↗

Development and Durability Testing of a Low‐Temperature Sintering Bi–Si–Zn Oxide Glass Composite Material (GCM) 129 I Waste Form

The capture and safe storage of radiological iodine ( 129 I) from nuclear fuel reprocessing is of concern due to its long half‐life and potential mobility in the environment. The development of durable waste forms in which to store captured iodine requires materials that are both compatible with the iodine capture phases and durable to repository environments. To that end, Sandia is developing a low‐temperature sintering Bi–Si–Zn oxide glass composite material (GCM) waste form and herein presents results of durability testing. Furthermore, durability studies were extended to both the occluded iodine capture material Ag‐Zeolite (Mordenite, MOR) as well as the GCM, synthesized with compositional variations including: amount of Ag flake added, AgI‐MOR particle size in the GCM, and mass loading of I within the AgI‐MOR. Product consistency test (PCT‐B), chemical durability (MCC‐1) tests, and single‐pass flow‐through (SPFT) tests, were performed on both the individual components of the GCM and the completed GCMs. Durability tests indicate low GCM dissolution rates (<10 −3 g/m 2 ·d) across wide variable ranges including: pH, AgI‐MOR loading, I loading, and AgI‐MOR particle size. Results indicate that the Bi–Si–Zn oxide glass matrix sharply limits the release of iodine from the otherwise relatively fast degrading AgI‐MOR getter material. Furthermore, the formation of an amorphous AgI phase during sintering of the GCM results in the limitation of iodine release during waste form degradation. Durability of GCM and release rates approximate those of established nuclear waste glasses, or analogues such as basaltic glass. This suggests that the Bi–Si–Zn GCM is a viable candidate as a repository iodine waste form.

Mowry, Curtis D.↗

Designing Flexibility into the Authorized Radioactive Contents of the 9982 Shipping Package

The 9982 radioactive material shipping package, or the 9982, differs from the others by allowing a multitude of radionuclides instead of a single defined set. While allowing flexibility, this requires more justification on why these contents would be worthwhile and why they would not cause various safety hazards when shipped together. The latter was covered through mass limit calculations, and the potential uses for the package are shown through comparison with historical shipments. Here, the mass limits were already calculated[1] and used to show three example shipments are suitable for the 9982 as well. Plutonium stored in 3013 containers[2], training sources shipped in 9977 packages[3], and americium standards shipped in 9978 packages[4] were all analyzed. The mass of each radionuclide and the corresponding mass limit were used to first determine if the listed content could be shipped. If so, the maximum allowed mass of such contents is also calculated in order to see if the 200-gram fissile limit for the 9982 would be violated if additional material was packed. The sum-of-the-fractions method produces contents that do not violate the mass limits or exceed the 200-gram fissile limit. These sets also serve as realistic examples of what may be shipped in the 9982. Well-founded example contents will help the approval of the package by showing its compatibility with previously shipped material. Unfounded hypothetical contents would not show the usefulness of having a wide variety of allowed radionuclides. More contents may be developed in order to incorporate other radionuclides that were not present in these three examples. The light elements will also need to be evaluated due to their exclusion currently preventing some materials from being allowed in the 9982.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Literature Review: Silicone Applications in Health Care

Early in the 20 th century, the term ‘silicone’ was coined by Professor Frederic Stanley Kipping, a British chemist and one of the founding fathers of silicon chemistry. The word was given to describe new compounds containing a Si-O linkage (siloxane bond) and basic chemical formula R 2 -Si-O. In industry, silicone usually refers to linear polydimethylsiloxane (PDMS), the most basic silicone polymer containing only methyl groups as substituents in the polymeric structure. However, the term silicone can also be used to describe complex polymer structures that feature a wide range of functional groups, branching or crosslinking. “The properties of basic PDMS materials can be changed by replacing some methyl groups with other organic groups or atoms.” Substitution of this type is useful when specific physical and chemical properties are required of the material, such as adhesion or compatibility with a certain substrate.

36 MATERIALS SCIENCE↗

Materials technology programs in support of a mercury Rankine space power system

A large portion of the materials technology is summarized that was generated in support of the development of a mercury-rankine space power system (SNAP-8). The primary areas of investigation are: (1) the compatibility of various construction materials with the liquid metals mercury and NaK, (2) the mechanical properties of unalloyed tantalum, and (3) the development of refractory metal/austenitic stainless steel tubing and transition joints. The primary results, conclusions, and state of technology at the completion of this effort for each of these areas are summarized. Results of possible significance to other applications are highlighted.

Stone, P. L.↗

Computational Materials Design for Ceramic Nuclear Waste Forms Using Machine Learning, First-Principles Calculations, and Kinetics Rate Theory

Ceramic waste forms are designed to immobilize radionuclides for permanent disposal in geological repositories. One of the principal criteria for the effective incorporation of waste elements is their compatibility with the host material. In terms of performance under environmental conditions, the resistance of the waste forms to degradation over long periods of time is a critical concern when they are exposed to natural environments. Due to their unique crystallographic features and behavior in nature environment as exemplified by their natural analogues, ceramic waste forms are capable of incorporating problematic nuclear waste elements while showing promising chemical durability in aqueous environments. Recent studies of apatite- and hollandite-structured waste forms demonstrated an approach that can predict the compositions of ceramic waste forms and their long-term dissolution rate by a combination of computational techniques including machine learning, first-principles thermodynamics calculations, and modeling using kinetic rate equations based on critical laboratory experiments. By integrating the predictions of elemental incorporation and degradation kinetics in a holistic framework, the approach could be promising for the design of advanced ceramic waste forms with optimized incorporation capacity and environmental degradation performance. Such an approach could provide a path for accelerated ceramic waste form development and performance prediction for problematic nuclear waste elements.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Exploring Material Solutions for Supercritical CO 2 Applications above 800 °C

There has been recent interest in exploring revolutionary supercritical CO 2 (sCO 2 ) power cycles, and this exploratory investigation was seeking materials with CO 2 compatibility at up to 1200 °C. Here, initial exposures were conducted at 0.1 and 2 MPa CO 2 for up to 1000 h at 900–1200 °C. As expected, specimens of Mo and W that might be used as matrix materials in cermets were rapidly attacked under these conditions. Even an alumina-forming FeCrAlMo alloy showed high mass gains in less than 100 h at 1200 °C due to the formation of Fe-rich oxide. However, at 900–1100 °C, more protective behavior was observed for FeCrAlMo specimens, with or without pre-oxidation, in 0.1 MPa CO 2 , but increased attack was observed in 2 MPa CO 2 . In contrast, most Ni-based alloys exposed at 900–1100 °C showed higher mass gains and thicker reaction products than formed in air. Thus, Ni-based alloys appear less compatible with CO 2 environments above 800 °C compared to lower temperatures. Low mass gains were observed for CVD SiC at 900–1200 °C, but MoSi 2 and Mo(Si,Al) 2 specimens did not form protective scales under these conditions at 1000 and 1100 °C.

36 MATERIALS SCIENCE↗

Integrated Force Method for Indeterminate Structures

Two methods of solving indeterminate structural-mechanics problems have been developed as products of research on the theory of strain compatibility. In these methods, stresses are considered to be the primary unknowns (in contrast to strains and displacements being considered as the primary unknowns in some prior methods). One of these methods, denoted the integrated force method (IFM), makes it possible to compute stresses, strains, and displacements with high fidelity by use of modest finite-element models that entail relatively small amounts of computation. The other method, denoted the completed Beltrami Mitchell formulation (CBMF), enables direct determination of stresses in an elastic continuum with general boundary conditions, without the need to first calculate displacements as in traditional methods. The equilibrium equation, the compatibility condition, and the material law are the three fundamental concepts of the theory of structures. For almost 150 years, it has been commonly supposed that the theory is complete. However, until now, the understanding of the compatibility condition remained incomplete, and the compatibility condition was confused with the continuity condition. Furthermore, the compatibility condition as applied to structures in its previous incomplete form was inconsistent with the strain formulation in elasticity.

Hopkins, Dale A.↗