Results for “Mars sample return” — Page 46

NASA NTRSDate not supplied

Uncertainty Modeling for Mars Ascent Vehicle’s Aerodatabase Development

The design of the Mars Ascent Vehicle - Mars Sample Return (MAV-MSR) trajectories requires an accurate assessment of flight performance. Typically, these trajectories are developed by flight mechanics analysis to meet complex mission requirements and then flight performance assessed through Monte Carlo simulations. Consequently, it is crucial to develop an aerodynamic aerodatabase as an input model for flight mechanics analysis to provide static and dynamic force and moment coefficients under specific flight conditions. The force and moment coefficients in the MAV aerodatabase are determined using the FUN3D computational fluid dynamics solver. Firstly, an overview of the aerodatabase is presented to demonstrate its applicability to trajectory-defined simulations. This effort is followed by an initial attempt to quantify uncertainties in the force and moment coefficients necessary for updating the current aerodatabase. The uncertainty model identifies uncertainty adders and multipliers for coefficient-based forces and moments through a direct comparison between FUN3D and wind tunnel test data from NASA Marshall Space Center's 14x14 inch Trisonic Wind Tunnel. These uncertainties aim to encompass various changes in Mach number, angle of attack, and aerodynamic roll angle.

Uncertainty analysis↗

NASA NTRSDate not supplied

Uncertainty Modeling for Mars Ascent Vehicle’s Aerodynamic Database Development

The design of the Mars Ascent Vehicle - Mars Sample Return (MAV-MSR) trajectories requires an accurate assessment of flight performance. Typically, these trajectories are developed by flight mechanics analysis to meet complex mission requirements and then flight performance assessed through Monte Carlo simulations. Consequently, it is crucial to develop an aerodynamic aerodatabase as an input model for flight mechanics analysis to provide static and dynamic force and moment coefficients under specific flight conditions. The force and moment coefficients in the MAV aerodatabase are determined using the FUN3D computational fluid dynamics solver. Firstly, an overview of the aerodatabase is presented to demonstrate its applicability to trajectory-defined simulations. This effort is followed by an initial attempt to quantify uncertainties in the force and moment coefficients necessary for updating the current aerodatabase. The uncertainty model identifies uncertainty adders and multipliers for coefficient-based forces and moments through a direct comparison between FUN3D and wind tunnel test data from NASA Marshall Space Center's 14x14 inch Trisonic Wind Tunnel. These uncertainties aim to encompass various changes in Mach number, angle of attack, and aerodynamic roll angle.

Uncertainty analysis↗

NASA NTRSDate not supplied

Data Processing and Analysis of Performance Measurements From Ingenuity Rotors in the Jet Propulsion Laboratory 25-Ft Space Simulator

The success of Ingenuity completing over 71 flights on Mars has resulted in the possible use of two further optimized Ingenuity-sized helicopters to retrieve samples for the planned Mars Sample Return campaign. Data to validate performance for several rotor speeds, densities, configurations, and collectives will aid in the design process and help in understanding Ingenuity’s current performance limitations. Tests were performed at the Jet Propulsion Laboratory (JPL) in the 25-foot Space Simulator, which include the Engineering Design Model 1 (EDM-1) with and without a cruciform box, and the Transonic Rotor Test (TRT) which is a single rotor setup featuring the same blade geometry as EDM-1 but designed to spin at much higher RPMs. The experimental setup, test matrix, data processing, data quality, and the performance results for EDM1 and TRT campaigns are presented.

Processing↗

NASA NTRSDate not supplied

Enhanced Quantification of 3D Woven Composites Via Fourier Analysis and Structure Tensors Applied to CT Scans

NASA's development of advanced 3D woven carbon composites, such as HEEET and 3MDCP, represents a significant leap in materials designed to endure extreme atmospheric entry conditions. However, the internal complexity of these materials introduces a variety of structures and novel defect types. Traditional characterization methods rely on labor-intensive, manual examination of X-ray CT scans, demanding considerable time and expertise. This process, while thorough, is not sustainable for large-scale analysis and defect tracking. Addressing this critical challenge, this presentation introduces an innovative suite of automated tools and analytical techniques, pioneered by the Mars Sample Return (MSR) Earth Entry System (EES) Thermal Protection System (TPS) project. These advancements offer a more efficient and accurate approach for quantifying CT data and characterizing the defects of 3D woven composites.

Magnus Haw↗

NASA NTRSDate not supplied

Recent Developments of Thermal Protection Materials to Enable Lower Cost Space Missions

Introduction: Starting with the Commercial Crew Program, a new paradigm has emerged at NASA. Rather than designing rockets and spacecrafts for every mission optimized to achieve science, NASA has begun to use a service-based model and utilizing public-private partnership in developing the vehicles that can bring broader benefits as well as lower the cost for NASA missions. Commercial companies own and operate those vehicles. This allows NASA to not design missions from the bottom up, and has cost, risk, and schedule savings implications. On the other side, the constraints require meeting the requirements in terms of mass, volume, power, etc. By leveraging NASA developed technologies, commercial companies can quickly demonstrate the commercial mission concept, and, through technology transfer, adopt needed technology to address supply chain problems. A downside is that the technology has to be sufficiently mature to be transferred by NASA, which means that it requires significant investment, expertise, and time to develop. Space entities are focused on rapid development with an emphasis on manufacturing and integration innovation with reduced cost and schedule and quick entrance into the market. Thermal Protection Systems (TPS) are mission critical, but their development takes years, and involve access to arc jets or unique test facilities. Therefore, their development is both risky and investment heavy. NASA ARC developed several new TPS materials over the last decade (C-PICA, HEEET, 3MDCP, 3DMAT, ADEPT woven TPS) and brought them to high TPS maturity, making them enablers for commercials space missions from LEO, Lunar Sample Return, Mars, and Venus missions. LEO missions are relevant to future Mars missions due to the comparable entry conditions. External Partners' Missions: C-PICA is a recent improvement on NASA’s heritage PICA lightweight TPS ablator. C-PICA is now considered an enabling technology for New Frontiers and other NASA missions. C-PICA was infused into several missions from external partners. Varda Space Industries’ Winnebago-1 spacecraft successfully returned to Earth from LEO on Feb. 21st, 2024, using a C-PICA heatshield. Inversion Space’s Ray vehicle will test both ARC’s C-PICA and SIRCA TPS materials on a LEO return mission later in 2024. The Kentucky Re-Entry Probe Experiment (KREPE) is another example of a low-cost flight experiment to demonstrate the use of small entry capsules to gather data with three instrumented Kentucky Re-entry and Universal Payload System (KRUPS) capsules. NASA Arc provided C-PICA and Soft-PICA for two of the next KRUPS capsules scheduled to re-enter Earth from the ISS later in 2024. Finally, Rocket Lab’s low-cost mission to Venus, scheduled to launch in December 2024, will search for habitable conditions in Venus’ cloud layer, making use of NASA ARC provided HEEET insulation layer heat shield, and SIRCA backshell TPS materials. Future NASA Missions: NASA’s ability to help commercial missions can lead to future low-cost missions for several reasons: Competition encourages lower cost; technology maturation is now done at an integrated system level; and a common design architecture between commercial and scientific applications requires no specialized engineering design. From an engineering perspective, both of these commercial LEO capsules aforementioned are capable of a Mars entry; the commercial payload mut be replaced with as science payload. Finally, several NASA mission concepts, that could be candidates for future SIMPLEx program calls, such as VATMOS-SR and Nephele, both proposing to target the Venusian atmosphere, would make use of the HEEET insulation layer TPS for part of their heat shield.

TPS materials↗

NASA NTRSDate not supplied

Sustaining Thermal Protection Systems Needed for Uranus Probes

Summary: Achieving Uranus in-situ science objectives through deploying probes in the atmosphere requires thermal protection systems capable of withstanding extreme entry environments. NASA’s 3-D Woven based thermal protection systems (TPS), developed specifically to meet this challenge, are mature, efficient, and capable of withstanding such entry. These science-enabling capabilities need to be sustained, otherwise mission implementation risk may increase to the point that the mission is untenable. The heatshield technology has been developed in concert with industry, and manufacturing processes have been technology transferred. Current technology readiness does not guarantee future availability. Sustainment requires maintaining expertise within NASA as well as ensuring that proven industrial expertise and capabilities will be readily available in the future. A constant awareness and risk assessment followed by risk mitigation are required. The scientific community needs to be aware of these challenges. It needs to engage NASA to ensure these capabilities will be available when needed. As was the case with the atrophy of heritage carbon phenolic that led to developing the 3-D Woven capabilities, our vigilance is again needed to sustain these enabling TPS capabilities for Uranus and for other missions. Background: NASA invested in and developed Heatshield for Extreme Entry Environment Technology (HEEET) TPS that was matured to TRL 6 in 2019 as a tiled system with seams and gap-fillers. Manufacturing readiness included development of specialized looms, molding, and infusion processes using commercial partners. In support of the Mars Sample Return mission, a single-layer, seamless, single-piece variant referred to as 3MDCP (3-D woven Mid-Density Carbon-Phenolic) was developed and is limited to a 1.3m maximum diameter scale due to weaving width limitations of 80”. Molding techniques developed to transform a flat, 2”-thick 3-D woven preform into a sphere-cone shape prior to phenolic resin infusion has been demonstrated. A team at NASA Ames is currently working with industry to demonstrate infusion at full-scale. By 2026, 3MDCP will be at a high level of maturity in technical, manufacturing, and integration readiness as well as material characterization. HEEET and 3MDCP for Uranus Entry: Several system studies have evaluated and baselined 3-D Woven TPS for Uranus entry, both HEEET as well as 3MDCP. If the aeroshell carrying the descent probe is 1.3m or less, then 3MDCP is a very capable and the most mass-efficient choice. If the aeroshell is bigger than 1.3m diameter, then HEEET can meet the mission need as it allows for an aeroshell of any diameter. HEEET and 3MDCP are capable of Saturn in-situ science missions prioritized in the New Frontiers-5 draft Announcement of Opportunity (AO) and if Saturn is the mission of choice, there is a pathway for sustaining the capability. Capability Sustainment: Given NASA’s current budgetary constraints, the postponement of the next New Frontiers AO to no earlier than 2026 and the unknown delay in starting the UOP flagship effort point to potential gap years for the HEEET and 3MDCP capabilities. The first step in capability sustainment is to understand the risks as they emerge, assess those risks, and develop plans to mitigate them. Keeping the science community, who are interested in UOP as well as the larger Giant Planet missions, informed of the emerging challenges requires continuous risk assessment/mitigation. Without these steps, atrophy is more likely within the industrial partners with which NASA has partnered. This presentation will provide more details as well as steps NASA can take to minimize the impact to the UOP mission.

Ethiraj Venkatapathy↗

NASA NTRSDate not supplied

Analysis of Integrated Spacecraft Performance Using A Rotating Detonation Rocket Engine

For spacecraft with especially stringent mass fraction constraints, the use of a rotating detonation rocket engine (RDRE) may yield potentially significant system mass savings. The pressure gain combustion inherent to RDREs provides higher thrust than traditional rocket engines for a given supply pressure and throat area. This opens multiple avenues for reducing system mass via higher specific impulse, reduced gravity losses, and reduced feed pressures. To highlight the potentially weight-saving characteristics of RDRE systems, the integrated performance of representative spacecraft designs using either a conventional rocket engine or an RDRE was assessed. This paper details the assumptions, methods, and results of this trade study. Two representative spacecraft were assessed. The first is a Liquid Mars Ascent Vehicle (MAV). This spacecraft was designed by NASA in 2011 for the Mars Sample Return Campaign but was not selected for flight due in part to it exceeding the mass requirements by 119 lbm. The second is MIURA-1, a kerolox sounding rocket developed by Payload Aerospace S.L.. The Liquid MAV assessment showed that an RDRE powered design met the mass requirements with a total vehicle mass 46 lbm below the limit. The MIURA-1 assessment showed that wall heat transfer and regenerative cooling are significant challenges for kerolox RDREs, but these challenges may be mitigated by reducing mixture ratio and using both propellants to cool the chamber. The assessment showed that an RDRE powered sounding rocket could achieve 12% more microgravity time than a conventional sounding rocket with the same payload and total vehicle mass. Alternately, if the payload mass and target apogee are held constant, then an RDRE powered sounding rocket can be 8% shorter and 11% lighter than a conventional sounding rocket. These results suggest that the advent of RDREs for in-space propulsion may unlock new missions for which conventional propulsion is not feasible.

Rotating Detonation Rocket Engine↗

NASA NTRSDate not supplied

Analysis of Integrated Spacecraft Performance Using Rotating Detonation Rocket Engine

For spacecraft with especially stringent mass fraction constraints, the use of a rotating detonation rocket engine (RDRE) may yield potentially significant system mass savings. The pressure gain combustion inherent to RDREs provides higher thrust than traditional rocket engines for a given supply pressure and throat area. This opens multiple avenues for reducing system mass via higher specific impulse, reduced gravity losses, and reduced feed pressures. To highlight the potentially weight-saving characteristics of RDRE systems, the integrated performance of representative spacecraft designs using either a conventional rocket engine or an RDRE was assessed. This paper details the assumptions, methods, and results of this trade study. Two representative spacecraft were assessed. The first is a Liquid Mars Ascent Vehicle (MAV). This spacecraft was designed by NASA in 2011 for the Mars Sample Return Campaign but was not selected for flight due in part to it exceeding the mass requirements by 119 lbm. The second is MIURA-1, a kerolox sounding rocket developed by Payload Aerospace S.L.. The Liquid MAV assessment showed that an RDRE powered design met the mass requirements with a total vehicle mass 46 lbm below the limit. The MIURA-1 assessment showed that wall heat transfer and regenerative cooling are significant challenges for kerolox RDREs, but these challenges may be mitigated by reducing mixture ratio and using both propellants to cool the chamber. The assessment showed that an RDRE powered sounding rocket could achieve 12% more microgravity time than a conventional sounding rocket with the same payload and total vehicle mass. Alternately, if the payload mass and target apogee are held constant, then an RDRE powered sounding rocket can be 8% short and 11% lighter than a conventional sounding rocket. These results suggest that the advent of RDREs for in-space propulsion may unlock new missions for which conventional propulsion is not feasible.

Rotating Detonation Rocket Engine↗

NASA NTRSDate not supplied

Supersonic Free-Flight Dynamics Testing in the Stratosphere

A new technique for obtaining stratospheric free-flight dynamics data for atmospheric entry capsules is described. The Stratospheric Projectile Experiment of Entry Dynamics (SPEED) represents a new approach to characterizing the free-flight dynamics of vehicles in the supersonic and transonic regime of flight. The SPEED test architecture leverages a stratospheric balloon and 3D-printed flight system in a novel two-stage configuration to deliver test articles to supersonic conditions in the atmosphere which achieve dynamic similitude with a full-scale vehicle. Designed to address the limitations of existing test facilities, SPEED captures the complete time evolution of a vehicle’s dynamic state while producing a statistically significant number of observed flight trajectories to address the stochastic nature of the wake-driven dynamic stability phenomenon. SPEED was developed over two years at NASA Ames Research Center. The inaugural flight of the SPEED test platform was conducted in the summer of 2024 where scaled capsules of the Mars Sample Return Earth Entry System and Dragonfly entry vehicle were tested. This paper describes the motivation for a new test architecture, operational constraints and achievable flight test envelopes, the design and development of the SPEED concept, and results from the demonstration flight. Techniques for estimating the dynamic aerodynamic characteristics and atmospheric conditions for each test article individually and as a collective are also discussed.

Entry Vehicle↗

NASA NTRSDate not supplied

Recent Developments of Thermal Protection Materials to Enable Lower Cost Space Missions

Introduction: Starting with the Commercial Crew Program, a new paradigm has emerged at NASA. Rather than designing rockets and spacecrafts for every mission optimized to achieve science, NASA has begun to use a service-based model and utilizing public-private partnership in developing the vehicles that can bring broader benefits as well as lower the cost for NASA missions. Commercial companies own and operate those vehicles. This allows NASA to not design missions from the bottom up, and has cost, risk, and schedule savings implications. On the other side, the constraints require meeting the requirements in terms of mass, volume, power, etc. By leveraging NASA developed technologies, commercial companies can quickly demonstrate the commercial mission concept, and, through technology transfer, adopt needed technology to address supply chain problems. A downside is that the technology has to be sufficiently mature to be transferred by NASA, which means that it requires significant investment, expertise, and time to develop. Space entities are focused on rapid development with an emphasis on manufacturing and integration innovation with reduced cost and schedule and quick entrance into the market. Thermal Protection Systems (TPS) are mission critical, but their development takes years, and involve access to arc jets or unique test facilities. Therefore, their development is both risky and investment heavy. NASA ARC developed several new TPS materials over the last decade (C-PICA, HEEET, 3MDCP, 3DMAT, ADEPT woven TPS) and brought them to high TPS maturity, making them enablers for commercials space missions from LEO, Lunar Sample Return, Mars, and Venus missions. LEO missions are relevant to future Mars missions due to the comparable entry conditions. External Partners' Missions: C-PICA is a recent improvement on NASA’s heritage PICA lightweight TPS ablator. C-PICA is now considered an enabling technology for New Frontiers and other NASA missions. C-PICA was infused into several missions from external partners. Varda Space Industries’ Winnebago-1 spacecraft successfully returned to Earth from LEO on Feb. 21st, 2024, using a C-PICA heatshield. Inversion Space’s Ray vehicle will test both ARC’s C-PICA and SIRCA TPS materials on a LEO return mission later in 2024. The Kentucky Re-Entry Probe Experiment (KREPE) is another example of a low-cost flight experiment to demonstrate the use of small entry capsules to gather data with three instrumented Kentucky Re-entry and Universal Payload System (KRUPS) capsules. NASA Arc provided C-PICA and Soft-PICA for two of the next KRUPS capsules scheduled to re-enter Earth from the ISS later in 2024. Finally, Rocket Lab’s low-cost mission to Venus, scheduled to launch in December 2024, will search for habitable conditions in Venus’ cloud layer, making use of NASA ARC provided HEEET insulation layer heat shield, and SIRCA backshell TPS materials. Future NASA Missions: NASA’s ability to help commercial missions can lead to future low-cost missions for several reasons: Competition encourages lower cost; technology maturation is now done at an integrated system level; and a common design architecture between commercial and scientific applications requires no specialized engineering design. From an engineering perspective, both of these commercial LEO capsules aforementioned are capable of a Mars entry; the commercial payload mut be replaced with as science payload. Finally, several NASA mission concepts, that could be candidates for future SIMPLEx program calls, such as VATMOS-SR and Nephele, both proposing to target the Venusian atmosphere, would make use of the HEEET insulation layer TPS for part of their heat shield.

TPS materials↗

NASA NTRSDate not supplied

Advanced Supersonic Parachute Inflation Research Experiment 2 (ASPIRE2) Flight Mechanics and Parachute Performance

The Advanced Supersonic Parachute Inflation Re-search Experiment-2 (ASPIRE2) program consists of a sounding rocket flight test to be launched at Wallops Flight Facility (WFF) in 2025. This effort seeks to qualify the supersonic parachute for the Sample Retrieval Lander (SRL) under the Mars Sample Return (MSR) program, building off the successes of its predecessor program, ASPIRE, which launched in both 2017 and 2018. The conops for the ASPIRE2 mission are shown in Figure 1 relative to its predecessor. While the ASPIRE pro-gram qualified a 21.5 m diameter disk-gap band parachute deployed at Mach 1.7, the SRL parachute will be increased to 24 m in diameter and target a Mach 2.1 parachute deployment condition, the largest diameter supersonic parachute deployed at the highest Mach number to date. These requirements are driven by the increased landing mass of the sample retrieval lander, which is roughly a 50% increase over that of the Mars2020 entry vehicle. These changes necessitate ASPIRE2 to certify the parachute performance under similar deployment conditions. This work will cover the 6-DoF para-chute model implementation and flight mechanics performance for the ASPIRE2 campaign and discuss how these results will impact the design of the test article. The ASPIRE2 trajectory is simulated using a multi-body flight dynamics tool, Program to Optimize Simulated Trajectories II (POST2). This work will summarize both the flight mechanics and parachute modeling (from payload separation until splashdown) and performance for this mission. Various design trades will be assessed such as para-chute tuning parameters as well as vehicle center of gravity location.

Evan Roelke↗

NASA NTRSDate not supplied

Quantitative Characterization of 3D Woven Composites Via Fourier Analysis and Structure Tensors Applied to CT Scans

NASA's development of advanced 3D woven carbon composites, such as HEEET and 3MDCP, represents a significant leap in materials designed to endure extreme atmospheric entry conditions. However, the internal complexity of these materials introduces a variety of structures and novel defect types. Traditional characterization methods rely on labor-intensive, manual examination of X-ray CT scans, demanding considerable time and expertise. This process, while thorough, is not sustainable for large-scale analysis and defect tracking. Addressing this critical challenge, this presentation introduces an innovative suite of automated tools and analytical techniques, pioneered by the Mars Sample Return (MSR) Earth Entry System (EES) Thermal Protection System (TPS) project. These advancements offer a more efficient and accurate approach for quantifying CT data and characterizing the defects of 3D woven composites.

3D Woven↗

NASA NTRSDate not supplied

New Tools for Automating Arcjet Sample Recession Tracking and Analysis

Arcjet Computer Vision (arcjetCV) has been significantly upgraded to enhance accuracy and performance in tracking material recession and shock-material standoff in test videos. These improvements include integrating new machine learning models, developing a specialized edge detection class, and incorporating a more comprehensive training dataset. These upgrades have refined the software’s ability to automate time-resolved recession tracking, making it more precise and reliable for analyzing complex physical processes. In parallel, a new tool called STARscan (Spatial Targeting and Alignment Rig for Scanning) is being developed to capture detailed 3D surface data before and after testing. By comparing these pre- and post-test scans with arcjetCV’s automated video analysis results, users can achieve a more comprehensive assessment of material recession. This method enables cross-validation of results, improving confidence in the analysis of tested materials. The expanded capabilities of arcjetCV have been successfully demonstrated on videos from various facilities, including the NASA Ames arcjets, UIUC’s PlasmatronX, and the VKI Plasmatron. It has been adopted as a new standard for in-situ recession tracking by the Mars Sample Return Project and Orion. ArcjetCV’s improved efficiency and accuracy are critical for reducing testing uncertainties and validating heatshield material performance under extreme conditions. The software’s user-friendly graphical interface ensures ease of use, enabling seamless processing and precise analysis of arcjet videos, providing deeper insights into material behavior in hypersonic environments. ArcjetCV is now available on both PyPI and Conda, allowing easy installation via "pip install arcjetCV" or through the Conda package manager, ensuring broad accessibility and streamlined deployment for users across various platforms.

Ablation↗

NASA NTRSDate not supplied

An Approach for Practical Grid-Resolved Roughness Aerothermodynamic Simulations for Woven Heatshield Surfaces

An approach for simulating the aerothermal environment over a patterned roughness surface within an otherwise axisymmetric flow is developed. The patterned roughness is simplified into a sinusoidal shape that captures the basic features of a charred 3MDCP ablator. Two orientations of this pattern, which are equally flight relevant due to the forming process, enable periodic boundary conditions along the edges of a grid spanning a single roughness element. This simplified three-dimensional grid represents the minimum problem size for a patterned roughness simulation, which enables computationally efficient grid-resolved roughness simulations. This approach is validated by simulating the Langley Mach 6 measurements made on a similar sinusoidal surface, which results in convective heating within 5% of the experimental data. Applying this approach to Mars Sample Return (MSR) Earth Entry System (EES) flight cases, considering simulations with both 11 species air and 30 species air with ablation products, results in heating augmentation that is slightly lower than the widely-used Dahm correlation approach, with the difference being dependent on pattern orientation. This result provides the only insight into the behavior of the roughness augmentation at the high temperature reacting flow conditions present for EES flight cases, which are not captured by available ground test measurements. For shear augmentation, the simulations revealed that the surface-parallel pressure component is dominant. For arc-jet tests targeted to flight values for shear, the higher arc-jet pressures required to match flight values for shear result in up to a 400% increase in the rough wall shear value, which is not captured by the Dahm correlation. This indicates that, to avoid significant over-testing, grid-resolved roughness simulations are required to determine arc-jet conditions that produce flight shear levels in rough-wall scenarios.

Christopher O Johnston↗

NASA NTRSDate not supplied

Dynamic Stability Test Technique for Blunt Bodies in a Magnetic Suspension and Balance System

Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.

Entry Systems Modeling↗

NASA NTRSDate not supplied

Dynamic Stability Test Technique for Blunt Bodies in a Magnetic Suspension and Balance System

Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.

Entry Systems Modeling↗

NASA NTRSDate not supplied

Multiscale Modeling of Woven Ablative Thermal Protection System Materials

The NASA Entry Systems Modeling project maintains a portfolio of computational model and tool development activities focused on reducing performance uncertainties in ablative Thermal Protection System (TPS) materials for NASA missions. The development activities span material scale and strive to allow microstructural characterization of material structure and properties, mesoscale analyses of damage, and macroscale evaluation of heatshield performance and recession in a given aerothermodynamic environment. This talk will detail the application of developed capabilities at all three scales to the woven TPS material that the Agency has selected as the heatshield for the Mars Sample Return Earth Entry System (MSR-EES) mission – 3D Mid-Density Carbon Phenolic (3MDCP). Each of the applications focuses on driving down uncertainties in material performance and thus risk for MSR-EES and other future missions that may leverage woven TPS. At the microscale, machine learning techniques are used to characterize images from destructive microscopy and inform structural variability. At the mesoscale, Lagrangian techniques are used to simulate ballistic impact and interpret damage modes noted in experiments. At the macroscale, coupled flow-material response techniques are validated by Arc Jet testing to enable heatshield design for missions with massive ablation.

Justin B Haskins↗

NASA NTRSDate not supplied

Three Dimensionally Woven Mid-Density Carbon Phenolic (3MDCP) is a Novel Single Piece Ablative TPS for Extreme Entry Environments

Three Dimensionally Woven Mid-Density Carbon Phenolic (3MDCP) is robust, single piece, carbon phenolic ablative thermal protection system under development at NASA Ames Research Center initially for the Mars Sample Return Earth Entry System (MSR EES). The MSR EES requirements drove the need for TPS with no seams, capable of surviving the highest entry conditions for any NASA Earth return capsule with heat fluxes >2000 W/cm2 and pressures >1.5 atmospheres. To produce 3MDCP required development of new weaving infrastructure to enable weaving of preforms large enough to form into a single piece heatshield. It required development of forming techniques to transform a flat woven panel into a sphere cone shape and enhanced infusion processes to support larger scale infusion of resin into the formed preforms. A rigorous performance testing campaign was conducted to develop and validate the materials thermal response model used to determine the required material thickness and to demonstrate the material can survive the extreme entry conditions. The end of the development effort (end of FY26) will result in a TPS at Technical Readiness Level (TRL) 6 and Manufacturing Readiness Level (MRL) 6+ for the MSR EES mission and a mature system ready to support other missions. This poster will provide a snapshot of where 3MDCP is in its development phase.

Ablator↗