SEARCH · Engineering Papers

Results for “LOW SPEED STABILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

NASA NTRS1960

Low-Speed Investigation of a Full-Span Internal-Flow Jet-Augmented Flap on a High-Wing Model with a 35 deg Swept Wing of Aspect Ratio 7.0

An investigation of a full-span 17-percent-chord internal-flow jet-augmented flap on an aspect-ratio-7.0 wing with 35 deg of sweepback has been made in the Langley 300-MPH 7- by 10-foot tunnel. Blowing over the conventional elevator and blowing down from a nose jet were investigated as a means of trimming the large diving moments at the high momentum and high lift coefficients. The results of the investigation showed that the model with the horizontal tail 0.928 mean aerodynamic chord above the wing-chord plane was stable to the maximum lift coefficient. The large diving-moment coefficients could be trimmed either with a downward blowing nose jet or by blowing over the elevator. Neither the downward blowing nose jet nor blowing over the elevator greatly affected the static longitudinal stability of the model. Trimmed lift coefficients up to 8.8 with blowing over the elevator and up to 11.4 with blowing down at the nose were obtained when the flap was deflected 70 deg and the total momentum coefficients were 3.26 and 4.69.

Turner, Thomas R.↗

NASA NTRS1988

Spatial stability of a compressible mixing layer

Presented are the results of a study of the inviscid spatial stability of a parallel compressible mixing layer. The parameters of this study are the Mach number of the moving stream, the ratio of the temperature of the stationary stream to that of the moving stream, the frequency and the direction of propagation of the disturbance wave. Stability characteristics of the flow as a function of these parameters are given. It is shown that if the Mach number exceeds a critical value there are always two groups of unstable waves. One of these groups is fast with phase speeds greater than 1/2, and the other is slow with speeds less than 1/2. Phase speeds for the neutral and unstable modes are given, as well as growth rates for the unstable modes. It is shown that three dimensional modes have the same general behavior as the two dimensional modes but with higher growth rates over some range of propagation direction. Finally, a group of very low frequency unstable modes was found for sufficiently large Mach numbers. These modes have very low phase speeds but large growth rates.

Jackson, T. L.↗

NASA NTRS1995

Sensitivity of Combustion-Acoustic Instabilities to Boundary Conditions for Premixed Gas Turbine Combustors

Premixed combustors, which are being considered for low NOx engines, are susceptible to instabilities due to feedback between pressure perturbations and combustion. This feedback can cause damaging mechanical vibrations of the system as well as degrade the emissions characteristics and combustion efficiency. In a lean combustor instabilities can also lead to blowout. A model was developed to perform linear combustion-acoustic stability analysis using detailed chemical kinetic mechanisms. The Lewis Kinetics and Sensitivity Analysis Code, LSENS, was used to calculate the sensitivities of the heat release rate to perturbations in density and temperature. In the present work, an assumption was made that the mean flow velocity was small relative to the speed of sound. Results of this model showed the regions of growth of perturbations to be most sensitive to the reflectivity of the boundary when reflectivities were close to unity.

Darling, Douglas↗

NASA NTRS1998

Boundary Layer Transition in the Leading Edge Region of a Swept Cylinder in High Speed Flow

Experiments were conducted on a 76 degree swept cylinder to establish the behavior of the attachment line transition process in a low-disturbance level, Mach number 1.6 flow. For a near adiabatic wall condition, the attachment-line boundary layer remained laminar up to the highest attainable Reynolds number. The attachment-line boundary layer transition under the influence of trip wires depended on wind tunnel disturbance level, and a transition onset condition for this flow is established. Internal heating raised the surface temperature of the attachment line to induce boundary layer instabilities. This was demonstrated experimentally for the first time and the frequencies of the most amplified disturbances were determined over a range of temperature settings. Results were in excellent agreement to those predicted by a linear stability code, and provide the first experimental verification of theory. Transition onset along the heated attachment line at an R-bar of 800 under quiet tunnel conditions was found to correlate with an N factor of 13.2. Increased tunnel disturbance levels caused the transition onset to occur at lower cylinder surface temperatures and was found to correlate with an approximate N factor of 1 1.9, so demonstrating that the attachment-line boundary layer is receptive to increases in the tunnel disturbance level.

Coleman, Colin P.↗

NASA NTRS1992

Investigation of the aerothermodynamics of hypervelocity reacting flows in the ram accelerator

New diagnostic techniques for measuring the high pressure flow fields associated with high velocity ram accelerator propulsive modes was experimentally investigated. Individual propulsive modes are distinguished by their operating Mach number range and the manner in which the combustion process is initiated and stabilized. Operation of the thermally choked ram accelerator mode begins by injecting the projectile into the accelerator tube at a prescribed entrance velocity by means of a conventional light gas gun. A specially designed obturator, which is used to seal the bore of the gun, plays a key role in the ignition of the propellant gases in the subsonic combustion mode of the ram accelerator. Once ignited, the combustion process travels with the projectile and releases enough heat to thermally choke the flow within several tube diameters behind it, thereby stabilizing a high pressure zone on the rear of the projectile. When the accelerating projectile approaches the Chapman-Jouguet detonation speed of the propellant mixture, the combustion region is observed to move up onto the afterbody of the projectile as the pressure field evolves to a distinctively different form that implies the presence of supersonic combustion processes. Eventually, a high enough Mach number is reached that the ram effect is sufficient to cause the combustion process to occur entirely on the body. Propulsive cycles utilizing on-body heat release can be established either by continuously accelerating the projectile in a single propellant mixture from low initial in-tube Mach numbers (M less than 4) or by injecting the projectile at a speed above the propellant's Chapman-Jouguet detonation speed. The results of experimental and theoretical explorations of ram accelerator gas dynamic phenomena and the effectiveness of the new diagnostic techniques are presented in this report.

Hertzberg, A.↗

NASA NTRS1994

Thin tailored composite wing for civil tiltrotor

The tiltrotor aircraft is a flight vehicle which combines the efficient low speed (i.e., take-off, landing, and hover) characteristics of a helicopter with the efficient cruise speed of a turboprop airplane. A well-known example of such vehicle is the Bell-Boeing V-22 Osprey. The high cruise speed and range constraints placed on the civil tiltrotor require a relatively thin wing to increase the drag-divergence Mach number which translates into lower compressibility drag. It is required to reduce the wing maximum thickness-to-chord ratio t/c from 23% (i.e., V-22 wing) to 18%. While a reduction in wing thickness results in improved aerodynamic efficiency, it has an adverse effect on the wing structure and it tends to reduce structural stiffness. If ignored, the reduction in wing stiffness leads to susceptibility to aeroelastic and dynamic instabilities which may consequently cause a catastrophic failure. By taking advantage of the directional stiffness characteristics of composite materials the wing structure may be tailored to have the necessary stiffness, at a lower thickness, while keeping the weight low. The goal of this study is to design a wing structure for minimum weight subject to structural, dynamic and aeroelastic constraints. The structural constraints are in terms of strength and buckling allowables. The dynamic constraints are in terms of wing natural frequencies in vertical and horizontal bending and torsion. The aeroelastic constraints are in terms of frequency placement of the wing structure relative to those of the rotor system. The wing-rotor-pylon aeroelastic and dynamic interactions are limited in this design study by holding the cruise speed, rotor-pylon system, and wing geometric attributes fixed. To assure that the wing-rotor stability margins are maintained a more rigorous analysis based on a detailed model of the rotor system will need to ensue following the design study. The skin-stringer-rib type architecture is used for the wing-box structure. The design variables include upper and lower skin ply thicknesses and orientation angles, spar and rib web thicknesses and cap areas, and stringer cross-sectional areas. These design variables will allow the maximum tailoring of the structure to meet the design requirements most efficiently. Initial dynamic analysis has been conducted using MSC/NASTRAN to determine the baseline wing's frequencies and mode shapes. For the design study we intend to use the finite-element based code called WIDOWAC (Wing Design Optimization With Aeroeastic Constraints) that was developed at NASA Langley in early 1970's for airplane wing structural analysis and preliminary design. Currently, the focus is on modification and validation of this code which will be used for the civil tiltrotor design efforts.

Rais-Rohani, Masoud↗

NASA NTRS1961

Aerodynamic Characteristics of a Four-Propeller Tilt-Wing VTOL Model with Twin Vertical Tails, Including Effects of Ground Proximity

Results are presented of a wind-tunnel investigation of the aerodynamic stability, control, and performance characteristics of a model of a four-propeller tilt-wing VTOL airplane employing flaps and speed brakes through the transition speed range. The results indicate that the wing was stalled for steady level flight for all conditions of the investigation; however, the flapped configuration did produce a higher maximum lift. The effectiveness of the flap in delaying the stall in the present investigation was not as great as in some previous investigations because the flap used was smaller than that used previously. The wing stall resulted in an appreciable reduction of aileron effectiveness during the transition. Out of ground effect the low horizontal tail did not appear to be in an adverse flow field as had been expected and showed no erratic changes in effectiveness; however, in ground effect a large nose-down moment was experienced by the model. In general, the lateral aerodynamic data indicate that the configuration is directionally stable and possesses positive dihedral effect throughout the transition, and the data show no signs of erratic flow at the vertical tails.

Grunwald, Kalman J.↗

NASA NTRSDate not supplied

Instabilities in the Wake of Roughness on a Flat Plate in a Quiet Supersonic Tunnel

Roughness-induced transition is an unavoidable reality in practical high-speed vehicles. Typical prediction of transition due to roughness include algebraic correlations and, more recently, semi-empirical methods. In the NASA Langley Research Center Supersonic Low Disturbance Tunnel, a Mach 3.5 quiet tunnel, several transition experiments have been performed in the past decade to better understand the mechanisms by which small roughness causes transition in a supersonic boundary layer. The study started first with isolated roughness elements of different planforms and shapes and progressed to increasingly more complicated geometries before arriving at a pseudorandom roughness, defined by an analytic function. Concurrent computational efforts progressed with these studies as well, starting with the use of linear stability theory and progressing to the use of harmonic linearized Navier-Stokes to predict the growth of boundary layer stabilities.

Amanda Chou↗

NASA NTRS1989

High performance linear-quadratic and H-infinity designs for a 'supermaneuverable' aircraft

Recent efforts by the National Aeronautics and Space Administration Langley Research Center have focused on expanding the flight envelope of the F/A-18 aircraft. Of particular concern has been the low speed, high angle-of-attack regime over which the conventional aerodynamic controls of the F/A-18 lose their effectiveness. In order to address this problem the F18 high alpha research vehicle was developed. This aircraft is essentially a modified F/A-18 which possesses thrust vectoring capabilities and hence increased maneuverability in this flight regime. The linear-quadratic-Gaussian with loop-transfer-recovery and H(infinity) design methodologies are used to design high performance controllers for the F18 at an operating point within the expanded envelope. In addition, how the control redundancy of the F18 can be used to maintain nominal performance, as well as nominal stability, in situations where failures occur, is shown.

Voulgaris, Petros↗

NASA NTRS1989

Inviscid spatial stability of a compressible mixing layer

Presented are the results of a study of the inviscid spatial stability of a parallel compressible mixing layer. The parameters of this study are the Mach number of the moving stream, the ratio of the temperature of the stationary stream to that of the moving stream, the frequency and the direction of propagation of the disturbance wave. Stability characteristics of the flow as a function of these parameters are given. It is shown that if the Mach number exceeds a critical value there are always two groups of unstable waves. One of these groups is fast with phase speeds greater than 1/2, and the other is slow with speeds less than 1/2. Phase speeds for the neutral and unstable modes are given, as well as growth rates for the unstable modes. It is shown that three-dimensional modes have the same general behavior as the two-dimensional modes but with higher growth rates over some range of propagation direction. Finally, a group of very low frequency unstable modes was found for sufficiently large Mach numbers. These modes have very low phase speeds but large growth rates.

Jackson, T. L.↗

NASA NTRS1947

Longitudinal Stability and Control Characteristics of a Semispan Model of the XF7U-1 Tailless Airplane at Transonic Speeds by the NACA Wing-Flow Method, TED No. NACA DE307

An investigation was made by the NACA wing-flow method to determine the longitudinal stability and control characteristics at transonic speeds of a semispan model of the XF7U-1 tailless airplane. The 25-percent chord line of the wing of the model was swept back 35 deg. The airfoil sections of the wing perpendicular to the 25-percent chord line were 12 percent thick. Measurements were made of the normal force and pitching moment through an angle-of-attack range from about -3 deg to 14 deg for several ailavator deflections at Mach numbers from 0.65 to about 1.08. The results of the tests indicated no adverse effects of compressibility up to a Mach number of at least 0.85 at low normal-force coefficients and small ailavator deflections. Up to a Mach number of 0.85, the neutral point at low normal-force coefficients was at about 25 percent of the mean aerodynamic chord and moved rearward irregularly to 41 or 42 percent with a further increase in Mach number to about 1.05. For deflections up to -8.0 percent, the ailavator was effective in changing the pitching moment except at Mach numbers from 0.93 to about 1.0 where ineffectiveness or reversal was indicated for deflections and normal-force coefficients. With -13.2 deg deflection at normal-force coefficients above about 0.3, reversal of ailavator effectiveness occurred at Mach numbers as low as 0.81. A nose-down trim change, which began at a Mach number of about 0.85, together with the loss in effectiveness of the ailavator, indicated that with increase in the Mach number from about 0.95 to 1.05 an abrupt ailavator movement of 5 deg or 6 deg first up and then down would be required to maintain level flight.

Sawyer, Richard H.↗

NASA NTRS2019

Effect of 3D Roughness Patch on Instability Amplification in a Supersonic Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of high-speed vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, sinusoidal shape roughness elements on a Mach 3.5 flat plate boundary layer for flow conditions corresponding to the planned conditions of an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at the NASA Langley Research Center. Analysis of convective instabilities in the wake of the roughness patch was reported in a previous paper and the current work extends that analysis to instability amplification across the length of the roughness patch. Quasi-parallel stability analysis of the modified boundary layer flow over the patch indicates two dominant families of unstable disturbances, namely, a group of high frequency modes that amplify in localized regions along the roughness patch and another group of low frequency modes that have smaller peak amplification rates but amplify steadily both above the roughness patch and in the wake region behind it. The results suggest that the amplification factors associated with the high-frequency modes are sufficiently low, at least for the roughness patches considered in this paper, so that these modes are unlikely to have a major influence on the transition process. The amplification of the low-frequency modes within the region of the roughness patch is further quantified via direct numerical simulations. Results confirm the strongly destabilizing influence of the roughness patch on the first mode instabilities, yielding an N-factor increment of ΔN ≈ 3.6 for a roughness patch length of eight wavelengths.

Laminar turbulent transition↗

DOE OSTI2023

SPUTTERED THIN FILMS FOR VERY HIGH POWER, EFFICIENT, AND LOW-COST COMMERCIAL SOFCS

The aim of this project was to leverage the low area specific resistance (ASR) of Redox’s GDC electrolyte-based cell architecture and increase solid oxide fuel cell (SOFC) efficiency (i.e., open circuit voltage, or OCV) without significantly increasing cell resistance. The key to achieving the increased SOFC efficiency is the introduction of a thin sputtered yttria stabilized zirconia (YSZ) electron-blocking layer and a thin sputtered gadolinia doped ceria (GDC) barrier layer on top of the half-cell substrate (i.e., anode and GDC electrolyte). A key initial effort of the project was to improve the quality of the half-cell substrate surface so that any remaining defects were significantly smaller than the desired film thickness. During lab-scale trials, we had to overcome challenges with film cracking during post-sputtering treatments (e.g., thermal anneals) as well as damage to the sputtering targets. After the initial lab-scale trials, the focus shifted toward the use of commercial scale sputtering equipment with a sputtering equipment manufacturer in the microelectronics industry. Using the commercial sputtering equipment, we deposited films with different variations of power, PO2, sputtering time, platen speed, etc. We then determined the combinations of sputtering conditions and post-sputtering treatments that yielded high-quality films without cracks or other significant defects. While thin films were deposited on cells as large as 10 cm by 10 cm, the processing was optimized using 4 cm by 4 cm cells. Cell performance was evaluated in stainless-steel test fixtures between 500 °C and 700 °C with hydrogen fuel fed to the anode and air fed to the cathode. Extensive studies allowed us to determine that modified cathode and cathode contact firing processes were required to achieve theoretical OCV. Moreover, use of the new firing processes resulted in the need for a modified cathode contact to achieve a low ASR. In summary, the project demonstrated the performance of high OCV (1.13 V at 650 °C) from sputtered layers and a low ASR (~0.25 Ohms-cm2 at 650 °C) resulting from a modification of cathode/contact processing and the introduction of alternative contact layers that are sufficient to yield a Gen-1 cell with a maximum power density of approximately 1.2 W/cm2. At an operating voltage of 0.74 V, this would yield a cell power density of ~1.1 W/cm2. While not utilized in this project, a Redox Gen-2 cell has a catalyst-infiltrated porous anode that reduces the ASR by more than 50% from that of the Gen-1 cells used in this project. Therefore, if the sputtered YSZ electron-blocking layer and GDC barrier layer are added to a Gen-2 half cell with a similar increase in OCV to the theoretical value of ~1.13 V at 650 °C, and if the same improvement in ASR (from that demonstrated in this project) is achieved when using the Gen-2 half-cell architecture as a sputtered cell substrate, then the power density at 0.74 Vop could be as high as ~2.6 W/cm2. The impact of such power density gains, while still maintaining high cell efficiency, and thus high system efficiency, is a dramatic decrease in system cost because the stack represents ~30-40% of the SOFC system cost.

01 COAL, LIGNITE, AND PEAT↗

NASA NTRS2016

Summary of the Second High-Altitude, Supersonic Flight Dynamics Test for the LDSD Project

NASA’s Low-Density Supersonic Decelerator Project is developing and testing the next generation of supersonic aerodynamic decelerators for planetary entry. A key element of that development is the testing of full-scale articles in conditions relevant to their intended use, primarily in the tenuous Mars atmosphere. To achieve this testing, the LDSD project developed a new test architecture for the qualification of their supersonic parachute. A large, helium filled scientific balloon is used to hoist a 4.7 m blunt body test vehicle to an altitude of approximately 32 kilometers. The test vehicle is released from the balloon, spun up for gyroscopic stability, and accelerated to over four times the speed of sound and an altitude of 50 kilometers using a large solid rocket motor. Once at those conditions, the vehicle is despun and the test period begins.

Clark, Ian↗

NASA NTRS1983

Development and fabrication of a high current, fast recovery power diode

A high voltage (VR = 1200 V), high current (IF = 150 A), fast recovery ( 700 ns) and low forward voltage drop ( 1.5 V) silicon rectifier was designed and the process developed for its fabrication. For maximum purity, uniformity and material characteristic stability, neutron transmutation n-type doped float zone silicon is used. The design features a hexagonal chip for maximum area utilization of space available in the DO-8 diode package, PIN diffused junction structure with deep diffused D(+) anode and a shallow high concentration n(+) cathode. With the high temperature glass passivated positive bevel mesa junction termination, the achieved blocking voltage is close to the theoretical limit of the starting material. Gold diffusion is used to control the lifetime and the resulting effect on switching speed and forward voltage tradeoff. For solder reflow assembly, trimetal (Al-Ti-Ni) contacts are used. The required major device electrical characteristics were achieved. Due to the tradeoff nature of forward voltage drop and reverse recovery time, a compromise was reached for these values.

Berman, A. H.↗

DOE OSTI2021

Evaluation of idealized large-eddy simulations performed with the Weather Research and Forecasting model using turbulence measurements from a 250 m meteorological mast

Abstract. We investigate the ability of the Weather Research and Forecasting model to perform large-eddy simulation of canonical flows. This is achieved through comparison of the simulation outputs with measurements from sonic anemometers on a 250 m meteorological mast located at Østerild, in northern Denmark. Østerild is on a flat and rough area, and for the predominant wind directions, the atmospheric flow can be considered to be close to homogeneous. The idealized simulated flows aim at representing atmospheric boundary layer turbulence under unstable, neutral, and stable stability conditions at the surface, which are statistically significant conditions observed at Østerild. We found that the resolved fields from the simulations appear to have the characteristics of the three stability regimes. Vertical profiles of observed mean wind speeds and direction are well reproduced by the simulations, with the largest differences under near-neutral conditions, where the effect of the subgrid-scale model is evident on the vertical wind shear close to the surface. Vertical profiles of observed eddy fluxes are also well reproduced by the simulations, with the largest differences for the three velocity component variances under stable stability conditions, although nearly always within the observed variability. With regards to turbulent kinetic energy, we find good agreement between observations and simulations at all vertical levels. Simulated and observed velocity spectra match very well and show very similar behavior with height and with atmospheric stability within the low-frequency interval; at the effective resolution, the simulated spectra show the typical drop-off of finite differences. Our findings demonstrate that these idealized simulations reproduce the characteristics of atmospheric stability regimes often observed at a high turbulent and flat site within a direction sector, where the air flows over nearly homogeneous land.

17 WIND ENERGY↗

NASA NTRS1982

Subsonic balance and pressure investigation of a 60 deg delta wing with leading edge devices

Low supersonic wave drag makes the thin highly swept delta wing the logical choice for use on aircraft designed for supersonic cruise. However, the high-lift maneuver capability of the aircraft is limited by severe induced-drag penalties attributed to loss of potential flow leading-edge suction. This drag increase may be alleviated through leading-edge flow control to recover lost aerodynamic thrust through either retention of attached leading-edge flow to higher angles of attack or exploitation of the increased suction potential of separation-induced vortex flow. A low-speed wind-tunnel investigation was undertaken to examine the high-lift devices such as fences, chordwise slots, pylon vortex generators, leading-edge vortex flaps, and sharp leading-edge extensions. The devices were tested individually and in combinations in an attempt to improve high-alpha drag performance with a minimum of low-alpha drag penalty. This report presents an analysis of the force, moment, and static pressure data obtained in angles of attack up to 23 deg, at Mach and Reynolds numbers of 0.16 and 3.85 x 10 to the 6th power per meter, respectively. The results indicate that all the devices produced drag and longitudinal/lateral stability improvements at high lift with, in most cases, minor drag penalties at low angles of attack.

Tingas, S. A.↗

NASA NTRS1986

An experimental investigation of the flap-lag-torsion aeroelastic stability of a small-scale hingeless helicopter rotor in hover

A small scale, 1.92 m diam, torsionally soft, hingeless helicopter rotor was investigated in hover to determine isolated rotor stability characteristics. The two-bladed, untwisted rotor was tested on a rigid test stand at tip speeds up to 101 m/sec. The rotor mode of interest is the lightly damped lead-lag mode. The dimensionless lead-lag frequency of the mode is approximately 1.5 at the highest tip speed. The hub was designed to allow variation in precone, blade droop, pitch control stiffness, and blade pitch angle. Measurements of modal frequency and damping were obtained for several combinations of these hub parameters at several values of rotor speed. Steady blade bending moments were also measured. The lead-lag damping measurements were found to agree well with theoretical predictions for low values of blade pitch angle. The test data confirmed the predicted effects of precone, droop, and pitch control stiffness parameters on lead-lag damping. The correlation between theory and experiment was found to be poor for the mid-to-high range of pitch angles where the theory substantially overpredicted the experimental lead-lag damping. The poor correlation in the mid-to-high blade pitch angle range is attributed to low Reynolds number nonlinear aerodynamics effects not included in the theory. The experimental results also revealed an asymmetry in lead-lag damping between positive and negative thrust conditions.

Sharpe, David L.↗