Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Grain Boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Effect of microstructure and neutron irradiation defects on deuterium retention in SiC

Retention of hydrogen isotopes is a critical concern for operating fusion reactors as retained tritium both activates components and removes scarce fuel from the fuel cycle. Radiation-induced displacement damage in SiC influences the retention of hydrogen isotopes compared to pristine SiC. Deuterium retention in neutron irradiated high purity SiC has been compared to different microstructures of non-irradiated high purity SiC using thermal desorption spectroscopy after gas charging and low energy ion implantation. Experimental results show lower deuterium retention in single crystal SiC than in polycrystal SiC indicating that grain boundaries are key trapping features in unirradiated SiC. Deuterium is released at lower temperatures in neutron irradiated polycrystal SiC compared to pristine polycrystal SiC, suggesting weaker trapping by radiation-induced defects compared to grain boundary trapping sites in the pristine materials. Low energy ion implantation caused a high deuterium release temperature, highlighting the sensitivity of deuterium release behaviour to radiation defect characteristics. First principles calculations have been conducted to identify energetically favourable trapping sites in SiC at the H ABc V Si and H TSi V C complexes, and migration barriers between interstitial sites. This helps interpret experimental results and derive effective diffusivity of hydrogen isotopes in SiC in the presence of vacancies.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Effect of prior creep at 1365 K on the room temperature tensile properties of several oxide dispersion strengthened alloys

An experimental study was conducted to determine whether oxide dispersion-strengthened (ODS) Ni-base alloys in wrought bar form are subject to creep degradation effects similar to those found in thin-gage sheet. The bar products evaluated included ODS-Ni, ODS-NiCr, and advanced ODS-NiCrAl types; the alloys included microstructures ranging from an essentially perfect single crystal to a structure consisting of very small elongated grains. Tensile test specimens were exposed to creep at various stress levels at 1365 K and then tensile tested at room temperature. Low residual tensile properties, change in fracture mode, appearance of dispersoid free bands, grain boundary cavitation, and/or internal oxidation are interpreted as creep degradation effects. The amount of degradation depends on creep strain, and degradation appears to be due to diffusional creep which produces dispersoid free bands around grain boundaries acting as vacancy sources.

Whittenberger, J. D.↗
NASA NTRS1986

Requirements for high-efficiency solar cells

Minimum recombination and low injection level are essential for high efficiency. Twenty percent AM1 efficiency requires a dark recombination current density of 2 x 10 to the minus 13th power A/sq cm and a recombination center density of less than 10 to the 10th power /cu cm. Recombination mechanisms at thirteen locations in a conventional single crystalline silicon cell design are reviewed. Three additional recombination locations are described at grain boundaries in polycrystalline cells. Material perfection and fabrication process optimization requirements for high efficiency are outlined. Innovative device designs to reduce recombination in the bulk and interfaces of single crystalline cells and in the grain boundary of polycrystalline cells are reviewed.

Sah, C. T.↗
DOE OSTI2022

Analytic model of dislocation density evolution in fcc polycrystals accounting for dislocation generation, storage, and dynamic recovery mechanisms

Here, an analytic model of the evolution of dislocation density in fcc polycrystals is described. The evolution equations approximately account for most known dislocation storage, dynamic recovery, and dislocation generation mechanisms in fcc polycrystals. Specifically, the model incorporates network (forest) and grain boundary storage, mobile-network and mobile–mobile annihilation, screw–screw annihilation via athermal and thermal single cross-slip, generation by double cross-slip (Koehler mechanism, including dipole formation), Frank-Read sources, grain boundary nucleation, and mobile–immobile dislocation nucleation due to shock loading. Single cross-slip is assumed to proceed through the Friedel–Escaig (FE) mechanism; the corresponding activation energy is calculated using a modified FE model. The activation energy for double cross-slip is calculated for the first time by extending the FE model. The exact evolution equations are integro-differential equations, and as such are difficult to implement in a code; hence, the evolution equations are simplified by making several approximations. Preliminary results on copper are presented, including comparisons to experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of annealing at 1000°C in flowing He with low O 2 concentration on the room temperature tensile properties of Mo alloys

NorthStar is developing an accelerator-based technology to produce the medical isotope Mo-99. A previous ORNL report (ORNL/SPR-2022/2490) studied the oxidation behavior of Mo in flowing He with low oxygen content at 800°C and 1000°C and it was shown that an O 2 concentration lower than ~5ppm (μ1/1) is required to achieve acceptable oxidation rates for wrought or powder metallurgy (PM) Mo. Oxidation may also impact the mechanical properties of Mo and this report summarizes tensile results at room temperature on wrought and PM Mo before and after exposure at 1000°C in flowing He with O 2 concentration varying from 1 to 15 ppm O 2 . It was found that oxidation at 1000°C results in a significant decrease of Mo strength and ductility with brittle intergranular fracture surfaces, likely due to the segregation of oxygen at grain boundaries. For the PM Mo material, the decrease in strength and ductility was also observed after annealing in vacuum at 1000°C, indicating that the diffusion of the oxygen trapped in the material pores to grain boundaries after 20-100h at 1000°C is sufficient to embrittle the material. Finally, initial results on actual aMo and high-density disks provided by NorthStar revealed the lack of ductility of the materials due to the specific disk microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development of a grain growth model for U 3 Si 2 using experimental data, phase field simulation and molecular dynamics

The purpose of this work is to develop a model for normal grain growth in U 3 Si 2 . The average grain boundary energy was determined from previously published molecular dynamics simulations. The grain growth kinetics were quantified at various temperatures by annealing nanocrystalline samples. Here, the mobility was determined by comparing phase field grain growth simulations to the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mechanistic interpretation of Nelson curves for PVP failures under high temperature hydrogen attack

As an empirically established design criterion, Nelson curves that relate the service temperature and the allowable hydrogen partial pressure have been developed and utilized for more than sixty years in pressure vessels and piping (PVP) safety design. Despite a relatively clear thermodynamic understanding of the high-temperature-hydrogen-attack (HTHA) problem, the detailed fracture process on the microstructural length scales, however, remains elusive, and a quantitative assessment of the PVP lifetime under HTHA from the available creep fracture dataset is still not possible. This work develops a microstructure-informed and micromechanics-based model by incorporating a synergy between hydrogen transport and intergranular-cavity-based fracture process. Based on the available creep lifetime data of C-0.5Mo steels, we are able to calibrate material constitutive parameters, and then conduct nonlinear finite element simulations that reveal a real-time stress-induced hydrogen diffusional transport along grain boundaries, coupled with a microstructure-explicit failure process, from which Nelson curves can be computed. Such failure analyses allow us to delineate two distinct regimes on the Nelson curves, i.e., dislocation-creep-controlled or grain boundary diffusion-assisted cavity growth. More importantly, we found that a small change of the pipe thickness and applied stresses can significantly shift these lifetime curves. However, these two parameters are usually not provided in Nelson curves, thus limiting their usage in material selection and safety design. In conclusion, this discrepancy can clearly be mitigated by extensive parametric studies from our micromechanical modeling/simulation framework.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Multiscale Modeling of Ultra High Temperature Ceramics (UHTC) ZrB2 and HfB2: Application to Lattice Thermal Conductivity

We are developing a multiscale framework in computational modeling for the ultra high temperature ceramics (UHTC) ZrB2 and HfB2. These materials are characterized by high melting point, good strength, and reasonable oxidation resistance. They are candidate materials for a number of applications in extreme environments including sharp leading edges of hypersonic aircraft. In particular, we used a combination of ab initio methods, atomistic simulations and continuum computations to obtain insights into fundamental properties of these materials. Ab initio methods were used to compute basic structural, mechanical and thermal properties. From these results, a database was constructed to fit a Tersoff style interatomic potential suitable for atomistic simulations. These potentials were used to evaluate the lattice thermal conductivity of single crystals and the thermal resistance of simple grain boundaries. Finite element method (FEM) computations using atomistic results as inputs were performed with meshes constructed on SEM images thereby modeling the realistic microstructure. These continuum computations showed the reduction in thermal conductivity due to the grain boundary network.

Lawson, John W.↗
NASA NTRS2012

Multiscale Modeling of UHTC: Thermal Conductivity

We are developing a multiscale framework in computational modeling for the ultra high temperature ceramics (UHTC) ZrB2 and HfB2. These materials are characterized by high melting point, good strength, and reasonable oxidation resistance. They are candidate materials for a number of applications in extreme environments including sharp leading edges of hypersonic aircraft. In particular, we used a combination of ab initio methods, atomistic simulations and continuum computations to obtain insights into fundamental properties of these materials. Ab initio methods were used to compute basic structural, mechanical and thermal properties. From these results, a database was constructed to fit a Tersoff style interatomic potential suitable for atomistic simulations. These potentials were used to evaluate the lattice thermal conductivity of single crystals and the thermal resistance of simple grain boundaries. Finite element method (FEM) computations using atomistic results as inputs were performed with meshes constructed on SEM images thereby modeling the realistic microstructure. These continuum computations showed the reduction in thermal conductivity due to the grain boundary network.

Lawson, John W.↗
DOE OSTI2026

Towards the Ultimate Strength of Medium‐Entropy Alloys Through Pulsed Lasers

The tensile strength of metals at extreme strain rates is a key predictor of their performance in ballistic and structural impact applications. An important experimental method to reach these extreme strain rates is the use of high-amplitude, short-duration pulsed lasers. The Jupiter Laser Facility at the Lawrence Livermore National Laboratory enabled probing for the first time the mechanical response of several promising High Entropy Alloys at times on the order of nanoseconds (strain rates of ∼10 7 and ∼10 9 s −1 ). The measured strength is in the range of 6 to 10 GPa, ten times the quasistatic value. The mechanisms of plastic deformation and failure were identified and quantified through analysis and molecular dynamics simulation. The reflected wave amplitudes, obtained by VISAR, were used to determine the tensile (spall) stress. The high tensile strength obtained is due to two factors: the strain-rate dependence of plastic flow and the kinetics of void nucleation, growth, and coalescence. The experimental results are compared with an analytical prediction considering both grain-interior and grain-boundary void initiation. Molecular dynamics simulations, conducted at strain rates of 10 8 and 10 9 s −1 , rationalize the experimental results. In conclusion, they provide valuable information about the process of failure evolution, and reveal that grain boundary separation plays a pivotal role in spalling.

Materials science↗
DOE OSTI2026

Novel architectures for stabilization of Mn-rich cathodes: a high-valent approach to interfaces

Lithium- and manganese-rich (LMR) layered oxides continue to generate significant interest as promising, earth-abundant cathode materials for next-generation Li-ion batteries. In spite of their attractive capacity and cost advantages, a few long-standing challenges still hamper their widespread adoption, with manganese dissolution being one of the most persistent and vexing issues. In the present study, we explore the incorporation of Sb5+ as a high-valent cation and exploit its ability to form unique lithium-rich surface and grain-boundary structures that can integrate directly with the LMR lattice. When synthesized under appropriate conditions, Sb5+ orders strongly with Li+ to form localized Li+–Sb5+ motifs, which play a key role in restructuring the surface and grain-boundary regions. These restructured regions act as protective, stabilizing entities that substantially suppress electrolyte-driven side reactions, reduce impedance growth, limit manganese dissolution, and help retain cyclable lithium during long-term electrochemical cycling. Further improvements of the electrochemical performance of Sb-treated LMR were achieved using a well-known additive to mitigate Mn dissolution and highlight the synergistic effects of combined strategies. Overall, this work showcases how high-valent elements such as Sb5+ can help tailor the surface and intergranular regions and work in synergy with other modifiers (e.g. electrolyte additives), enhancing the cycle life and practical viability of LMR cathodes for use in graphite-based full cells.

Mallick, Subhadip [Argonne National Laboratory (AN↗
DOE OSTI2021

Advances in CdZnTeSe for Radiation Detector Applications

Detection of X- and gamma-rays is essential to a wide range of applications from medical imaging to high energy physics, astronomy, and homeland security. Cadmium zinc telluride (CZT) is the most widely used material for room-temperature detector applications and has been fulfilling the requirements for growing detection demands over the last three decades. However, CZT still suffers from the presence of a high density of performance-limiting defects, such as sub-grain boundary networks and Te inclusions. Cadmium zinc telluride selenide (CZTS) is an emerging material with compelling properties that mitigate some of the long-standing issues seen in CZT. This new quaternary is free from sub-grain boundary networks and possesses very few Te inclusions. In addition, the material offers a high degree of compositional homogeneity. The advancement of CZTS has accelerated through investigations of the material properties and virtual Frisch-grid (VFG) detector performance. The excellent material quality with highly reduced performance-limiting defects elevates the importance of CZTS as a potential replacement to CZT at a substantially lower cost.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1984

Structural development in the Santa Catharina meteorite

A metallographic study was undertaken to seek support for the idea that Santa Catharina is really massive cloudy taenite. Available metal-rich nuggets of Santa Catharina appear to have been single crystals of taenite in the few centimeter size range, separated from each other by grain boundaries occupied by troilite and schreibersite. Metallographic and electron microprobe data allow one to postulate the following cooling and structural development history: (1) single crystal taenite formed at high temperature; (2) phosphate formed within the taenite and grain boundary schreibersite formed at interfaces with troilite or with other taenite crystals; (3) schreibersite began to precipitate within taenite at about 650 C; (4) at about 450 C the meteorite entered the three phase field at which point kamacite precipitated and started growing; and (5) kamacite/schreibersite interface measurements indicate that cooling continued down to about 350 C, with large Ni diffusion gradients developing within schreibersites.

Clarke, R. S., Jr.↗
DOE OSTI2021

Characterization of CdZnTeSe Nuclear Detector Chemically Etched in Bromine Methanol

Semiconductor nuclear radiation detectors made from tertiary and quaternary compounds of cadmium telluride (CdTe) can operate at room temperature without cryogenic cooling. One of such materials that have become of great interest is cadmium zinc telluride selenide (CdZnTeSe). Compared to other CdTe-based materials, such as cadmium zinc telluride (CdZnTe), CdZnTeSe can be grown with much less Te inclusions and sub-grain boundary networks. Chemical etching is often used to smoothen wafer surfaces during detector fabrication. This paper presents the characterization of CdZnTeSe that is chemically etched using bromine methanol solution. Infrared imaging shows that the wafer has no sub-grain boundary networks that often limit detector performance. The current-voltage (I-V) characterization experiment gave a resistivity of 4.6 × 10 10 Ω-cm for the sample. The I-V curve was linear in the ±10 to ±50 volts range. An energy resolution of 7.2% was recorded at 100 V for the 59.6-keV gamma line of 241 Am.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1973

Development of a Power Metallurgy Superalloy for Use at 1800-2000 F (980-1090 C)

A program was conducted to develop a powder metallurgy nickel-base superalloy for 1800-2000 F (980-1090 C) temperature applications. The feasibility of a unique concept for alloying carbon into a superalloy powder matrix and achieving both grain growth and a discrete particle grain boundary carbide precipitation was demonstrated. The process consisted of blending metastable carbides with a carbon free base alloy and consolidating this blend by hot extrusion. This was followed by heat treatment to grow a desired ASTM No. 2-3 grain size and to solution the metastable carbides to allow precipitation of discrete particle grain boundary carbides during subsequent aging heat treatments. The best alloy developed during this program was hydrogen-atomized, thermal-mechanically processed, modified MAR-M246 base alloy plus VC (0.28 w/o C). Although below those for cast MAR-M246, the mechanical properties exhibited by this alloy represent the best combination offered by conventional powder metallurgy processing to date.

Kortovich, C. S.↗
DOE OSTI2024

Exploring the relationship between deposition method, microstructure, and performance of Nb/Si-based superconducting coplanar waveguide resonators

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. Here, in this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigation of the relationship between classical and nonclassical ultrasound nonlinearity parameters and microstructural mechanisms in metals

This research studies two nonlinear ultrasound techniques: second harmonic generation and nonlinear resonant ultrasound spectroscopy, and the relationship to microstructural mechanisms in metals. The results show that there is a large change in both the classical, β, and nonclassical, α, ultrasound nonlinearity parameters in response to three specific microstructural mechanisms: precipitate growth in and along the grain boundaries, dislocations, and precipitate pinned dislocations. For example, both β and α increase with the growth of the precipitate radii (precipitate-pinned-dislocations). Additionally, both β and α increase when there is a growth of precipitates in and along the grain boundaries. As expected, β and α decrease when there is a removal of dislocations in the material. The relationship between β and α, and the microstructural mechanisms studied provide a quantitative understanding of the relationship between measured nonlinearity parameters and microstructural changes in metals, helping to demonstrate the possibility of using these two independent, but complementary, nonlinear ultrasound procedures to monitor microstructural damage.

Levy, Katherine Marie Scott↗