Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Investigation of the 30P30N Slat Flow Field with Passive Control Devices Using Particle Image Velocimetry

The leading-edge slat of a high-lift wing is one of the main noise contributors during approach and landing. This paper describes an experimental investigation of the velocity field associated with multiple passive noise treatments, including slat-cusp extensions, a cove filler, and a gap filler, on a two-dimensional multi-element high-lift 30P30N airfoil. Previous work documented comparisons of both surface and far field pressure fluctuations in the presence of these devices with those for a baseline case at different flow conditions. However, important information related to the velocity fields was missing from the previous measurements, hindering our ability to elucidate the changes in the flow physics associated with the noise treatments. Therefore, two-component Particle Image Velocity has been used to investigate the influence of passive noise treatments on the flow fields. All measurements are taken at an effective, free-air angle of attack of 5.5 degrees and a stowed-chord-based Reynolds number of 1.71 × 10e6. The measurements show that the slat extensions shorten the slat-cove shear layer trajectory, resulting in reduced growth of disturbances within the slat-cove shear layer. This leads to a shift of tonal peaks to higher frequencies and a reduction in the tonal amplitudes. The gap filler blocks the flow path through the gap, causing the reattachment location to shift to the main wing leading edge lower surface. Consequently, the feedback loop associated with the flow-acoustic interaction in the baseline case is eliminated, and the turbulent kinetic energy in the slat-cove shear layer is significantly reduced. However, extensive flow separation is observed on the suction side of the gap filler, which does not eliminate the noise reduction benefit due to the gap filler, but does degrade the aerodynamic performance of the high-lift configuration. Finally, the overall flow field in the presence of the cove filler is similar to that in the baseline case at the design angle of attack, but the slat-cove shear layer is eliminated leading to a suppression of the cavity tones associated with the shear layer. This change accounts for the reduction in slat noise as measured in previous work.

Aeroacoustics↗
NASA NTRSDate not supplied

Advancing Dust Tolerant Mechanisms for a Sustained Exploration of the Moon

Introduction: “I think dust is probably one of our greatest inhibitors to a nominal operation on the Moon. I think we can overcome other physio-logical or physical or mechanical problems except dust.”– Gene Cernan, Apollo 17 Technical Debrief The Apollo missions revealed the impact of lu-nar dust on mechanisms. Lunar dust particles are jagged and electrostatically charged, giving them the ability to bind or damage mechanisms and alter thermal properties. Reports documented clogged equipment and jammed mechanisms in every mission, regardless of surface duration, as well as clogged mechanisms in the Extravehicular Mobility Suit (EMS), including zippers, wrist and hose locks, faceplates, and sunshades [1-2]. Several astronauts remarked they could not have sustained surface activity much longer because clogged joints would have frozen up completely [2]. Effective dust mitigation strategies are need-ed to support longer duration stays on the lunar surface [3-4]. State of the Art: Technology for mechanisms able to operate in dusty enviroments is advancing rapidly due to the needs of both Mars rovers and the Artemis program. Vacuum-tight connectors are essential for spacesuits and habitats, and their performance can be dependent on cleaning technologies, which have proven difficult on the lunar surface. Several TRL 3-5 technologies are undergoing tests with the expectation to reach TRL 6 within 1-2 years. Some mechanisms will be infused and tested on the VIPER (Volatiles Inves-tigating Polar Exploration Rover) mission planned for mid-2020s. NASA Funded Efforts: NASA has recognized the need for dust tolerant mechanisms, and has partnered with industry to advance the state-of-the-art. At NASA GRC, KSC, and JSC, the Dust Tolerant Mechanisms Project is working to devel-op advanced actuator seals for rotary joints and rotary bearing technologies for long-term sus-tained operation in lunar dust environments. An-other NASA project at NASA GRC, partnered with GSFC, JPL, and KSC is Motors for Dusty & Ex-treme Cold Environments (MDECE). MDECE is developing an unheated magnetically-geared mo-tor that can operate continuously for a long dura-tion at an ambient temperature of -243 ºC (33 K). NASA GRC has the capability to characterize the effects of dust on seals, mechanisms, and other mating surfaces and components under lunar conditions [5]. Through the SBIR/STTR program, NASA has funded several companies to advance dust toler-ant mechanisms via the Dust Tolerant Mecha-nisms sub-topic with applications in surface mobil-ity, spacesuits, connectors, joints, and more. LSIC and Community Efforts: The Lunar Surface Innovation Consortium (LSIC) Dust Miti-gation focus group has fostered collaborations across NASA, industry, and academia to develop solutions that minimizes the impact of lunar dust on robotic and human systems. Community ef-forts have included topical meetings on dust tol-erant mechanisms, featured technology presenta-tions, and feedback to NASA on potential gaps and needs. Testing: In 2021, NASA released NASA-STD-1008 [6]. This NASA Technical Standard estab-lishes minimum requirements and provides guid-ance for testing systems and hardware to be ex-posed to dust in planetary environments. The standard has specific sections dedicated to Mechanisms Testing (e.g. bearings, gears) as well as Seals and Mating Surfaces Testing (e.g. hatches, docking systems). Gaps and Needs: NASA is tracking dust tol-erant mechanisms as a gap in a cross-directorate analysis of capability areas needed to enable fu-ture human space-flight architectures. Two high-priority gap areas include additional facilities for testing mechanisms in lunar-surface conditions, and a better understanding of vulnerabilities to the smallest, nanometer-scale dust particles. Conclusion: Understanding and mitigating lu-nar dust is critical to successful, sustained opera-tions on the lunar surface – whether autonomous or otherwise. This presentation will discuss both the state-of-the-art and open needs in lunar dust tolerant mechanisms, technology impacts, mitiga-tion approaches, testing, LSIC community efforts, and more. References: [1] Gaier, J. R. (2020). The Im-pact of Dust on Lunar Surface Equipment During Apollo. Lunar Dust 2020. [2] GRC, & Gaier, J. R. (2005). The Effects of Lunar Dust on EVA Sys-tems During the Apollo Missions. [3] Johansen, M. R. (2020). An Update on NASA’s Lunar Dust Mitigation Strategy. Lunar Dust 2020. [4] ASI, CSA, ESA, JAXA, & NASA. (2016). Dust Mitiga-tion Gap Assessment Report. [5] Jimenez, N. et al (2022), LPSC Abstract 2572. [6] NASA-STD-1008, 2021.

J I Nunez↗
NASA NTRS2023

Computer Human Interface Challenges in Space Exploration

NASA’s plans to return humans to the Lunar surface require overcoming a variety of challenging technical and operational obstacles. In 2022, NASA formed the Extravehicular Activity (EVA) and Human Surface Mobility (HSM) Program (EHP) at the Johnson Space Center with responsibilities including development of space suits and surface mobility systems for Lunar missions. This program includes a Technology Development and Partnerships office chartered to identify high priority gaps in capabilities for Lunar surface mobility and to coordinate resources to close those gaps. This presentation details the EHP technology roadmap for “Informatics and Decision Support,” a subset of spacecraft avionics focused on effective and autonomous crew interaction with spaceflight systems. The gaps, grouped into displays, audio systems, and information technology infrastructure, are largely driven by the unique interaction requirements for human spacecraft and the severe radiation environments beyond low earth orbit. The roadmap identifies ongoing activities and paths to technology infusion into Lunar spacecraft. NASA is seeking input on the content and ideas for alternative paths to gap closure. Closing these gaps is important to successful human operations on the Lunar surface and vital to NASA’s long-term goal of human missions to Mars.

Spacecraft Displays↗
NASA NTRSDate not supplied

Validation of a Probabilistic Continuity Assessment Method for Earth Observation Portfolios

With the increased reliance on spaceborne Earth observation data among the Earth science community and other end users, it is important that efforts are made to promote data continuity for a range of parameters of interest. Continuity gaps may occur between missions measuring like parameters due to mission development delays or early termination and introduce the potential of increased uncertainty for retrieved parameters. To inform portfolio-level decisions for Earth observing missions, Ivanco et al. developed a method that enables the assessment of the probability of continuity gaps for multi-mission architectures and provides a framework to assess this probability in the context of multiple scenarios that represent possible future states of the architecture [Ivanco et al., “A Scenario-Based Approach to Assess Continuity Gaps in Earth Observations,” IEEE Aerospace Conf., 2024]. While this method was previously applied to assess continuity gaps for a specific multi-mission architecture, it had not yet been validated with historical data. This paper outlines the process of validating the probabilistic gap assessment method by utilizing data obtained from past NASA Earth Science mission formulation documents and provides a discussion of the results and takeaways from the validation. Future areas of improvement pertaining to both the modeling and simulation methodologies and underlying assumptions are identified and discussed.

Katharine Burn↗
NASA NTRSDate not supplied

A Modeling Approach to Support Changeability Analysis and Management of Earth Observation Portfolios

Earth observing (EO) mission portfolios provide data on many geophysical parameters that collectively inform our understanding of the Earth system. To observe large-scale climate trends, it is important to collect data on many parameters over time. However, gaps may occur between missions due to formulation complexity, development delays, and uncertain events in operations. These gaps may impact the ability to provide sustained measurements. Developing a balanced EO mission portfolio is key to supporting study of the Earth system. Yet, decision-making at the portfolio level is a complex task because missions often address multiple parameters. Currently, the likelihood of data gaps is often assessed for an individual parameter, but decisions and events can impact data collection for many parameters. This poster introduces a modeling approach that supports management of the many parameter impacts of decisions and uncertain events. The approach provides a foundation for analyzing changeability in EO mission portfolios. Changeability analysis provides insight into a portfolio’s sensitivity to changes caused by decisions or uncertain events. The model is developed to analyze two aspects of changeability, robustness and flexibility, in EO mission portfolios. In context of these portfolios, the authors define robustness as a portfolio’s ability to provide sustained measurements despite future uncertainties, and they define flexibility as the availability of decision alternatives that contribute to parameter coverage at little detriment to the rest of the portfolio. The proposed model characterizes a portfolio’s sensitivity to change by capturing mission-parameter interconnectivity and redundancy in parameter coverage. The model can be analyzed to identify events that can create substantial gaps, thereby revealing focus areas for mitigation efforts. The model can also be analyzed to identify gap mitigation decisions that may improve parameter coverage with little detriment to the rest of the portfolio, thereby revealing favorable pathways for portfolio improvement. Developing a process for identifying these threats and opportunities will be the focus of future work. A parallel poster proposes a standard for visualizing and communicating portfolio-level impacts of decisions and uncertain events.

Lindsey Jacobson↗
NASA NTRS1974

Overvoltage protection network

Electrical equipment to be protected from overvoltage is connected with a possible source of overvoltage via an input conductor. A fuse is connected in series with the input conductor. A spark gap is connected between the input conductor and ground for conducting the overvoltage current to ground and for blowing the fuse to open the circuit to the electrical equipment. A pulse attenuator network is provided between the spark gap and the electrical equipment to be protected for attenuating the pulse of energy passing through the fuse and spark gap prior to blowing of the fuse. The pulse attenuator network includes additional shunt spark gaps, series inductance, and a series connection of a twisted shielded pair of conductors having low-voltage insulation.

Cambra, J. M.↗
NASA NTRS1974

Performance of LI-1542 reusable surface insulation system in a hypersonic stream

The thermal and structural performance of a large panel of LI-1542 reusable surface insulation tiles was determined by a series of cyclic heating tests using radiant lamps and aerothemal tests in the Langley 8-foot high-temperature structures tunnel. Aerothermal tests were conducted at a free-stream Mach number of 6.6, a total temperature of 1830 K, Reynolds numbers of 2.0 and 4,900,000 per meter, and dynamic pressures of 29 and 65 kPa. The results suggest that pressure gradients in gaps and flow impingement on the header walls at the end of longitudinal gaps are sources for increased gap heating. Temperatures higher than surface radiation equilibrium temperature were measured deep in gaps and at the header walls. Also, the damage tolerance of the LI-1542 tiles appears to be very high. Tile edge erosion rate was slow; could not be tolerated in a shuttle application. Tiles soaked with water and subjected to rapid depressurization and aerodynamic heating showed no visible evidence of damage.

Hunt, L. R.↗
NASA NTRS1975

Schottky barrier solar cell promises improved efficiency

Higher current and higher voltage can be obtained by using Schottky barrier device with wide band-gap semiconductor as top layer and lower band-gap semiconductor underneath. Significant amount of solar radiation that is not absorbed by side band-gap material will be absorbed by narrow band-gap material.

Stirn, R. J.↗
NASA NTRS1977

Open magnetic fields in active regions

Soft X-ray images and magnetograms of several active regions and coronal holes are examined which support the interpretation that some of the dark X-ray gaps seen between interconnecting loops and inner cores of active regions are foot points of open field lines inside the active regions. Characteristics of the investigated dark gaps are summarized. All the active regions with dark X-ray gaps at the proper place and with the correct polarity predicted by global potential extrapolation of photospheric magnetic fields are shown to be old active regions, indicating that field opening is accomplished only in a late phase of active-region development. It is noted that some of the observed dark gaps probably have nothing in common with open fields, but are either due to the decreased temperature in low-lying portions of interconnecting loops or are the roots of higher and less dense or cooler loops.

Svestka, Z.↗
NASA NTRS1978

Nonlinear axisymmetric liquid currents in spherical annuli

A numerical analysis of non-linear axisymmetric viscous flows in spherical annuli of different gap sizes is presented. Only inner sphere was supposed to rotate at a constant angular velocity. The streamlines, lines of constant angular velocity, kinetic energy spectra, and spectra of velocity components are obtained. A total kinetic energy and torque needed to rotate the inner sphere are calculated as functions of Re for different gap sizes. In small-gap annulus nonuniqueness of steady solutions of Navier-Stokes equations is established and regions of different flow regime existences are found. Numerical solutions in a wide-gap annulus and experimental results are used in conclusions about flow stability in the considered range of Re. The comparison of experimental and numerical results shows close qualitative and quantitative agreement.

Astafyeva, N. M.↗
NASA NTRS1982

Optimization of the performance of a tandem microchannel plate detector as a function of interplate spacing and voltage

The effect of varying the size of the gap voltage and spacing on the performance of a tandem pair of microchannel plates (MCP) is investigated. Results show that increasing the voltage in the gap increases the gain of the pair and also produces a narrower Gaussian pulse-height distribution, although beyond a critical voltage the gain of the channel plate pair is found to plateau. A model is developed which explains the nonlinear gain behavior of individual microchannels and the behavior of the electron cloud emitted from the first MCP as it spreads out between the two MCPs and hits the surface of the second. The model calculates the plateau voltage as a function of the gap size, the gain of each MCP, and the diameter of the channels, and is found to show good agreement with the observed results. It is concluded that interplate gaps of up to several millimeters can be accommodated without a significant degradation in pulse-height distribution.

Rogers, D.↗
NASA NTRS1983

Filler bar heating due to stepped tiles in the shuttle orbiter thermal protection system

An analytical study was performed to investigate the excessive heating in the tile to tile gaps of the Shuttle Orbiter Thermal Protection System due to stepped tiles. The excessive heating was evidence by visible discoloration and charring of the filler bar and strain isolation pad that is used in the attachment of tiles to the aluminum substrate. Two tile locations on the Shuttle orbiter were considered, one on the lower surface of the fuselage and one on the lower surface of the wing. The gap heating analysis involved the calculation of external and internal gas pressures and temperatures, internal mass flow rates, and the transient thermal response of the thermal protection system. The results of the analysis are presented for the fuselage and wing location for several step heights. The results of a study to determine the effectiveness of a half height ceramic fiber gap filler in preventing hot gas flow in the tile gaps are also presented.

Petley, D. H.↗
NASA NTRS1985

Designing high frequency ac inductors using ferrite and Molypermalloy Powder Cores (MPP)

The major considerations in the design of high frequency ac inductors are reviewed. Two methods for designing the inductor: the area product method and the core geometry method, are presented. The two major effects of the inductor air gap, fringing flux power loss and increase of inductance, are discussed. Equations for the inductor design and a step-by-step design procedure are given. The use of a lumped air gap or a distributed air gap are discussed and a comparison of the losses resulting from these gaps, together with experimental results are presented.

Mclyman, W. T.↗
NASA NTRS1987

Side-Looking Viewer for Crevices

Side-looking optical viewer inserted into gap 1 mm wide to depth of 10 cm. Instrument allows human observer to inspect small crevices from comfortable viewing angle. Small mirror atop pair of thin, flat legs inserted into gap. Mirror reflects image of gap wall or other object into microscope, which magnifies image 20 times. Quartz/halogen lamp in separate unit provides light to illuminate gap via optical-fiber bundle. Observer looks directly through microscope or attaches photographic or video camera without disturbing setup.

Hagen, G. R.↗
NASA NTRS1986

Breakdown characteristics of an isolated conducting object in a uniform electric field

A laboratory experiment was conducted to determine the physical processes involved in the electrical breakdown of a particular spark gap arrangement. The gap consists of an isolated conducting ellipsoid located midway between two large flat electrodes. Gradual increase of the applied electric field, E, in the gap produces corona on the ellipsoid tips followed by flashover in a leader-arc sequence. The leader phase consists of the abrupt formation of ionized channels which partially bridge the gap and then decay prior to the arc. Measurements of dE/dt and of current were made, and photographs were taken with an image converter. Experimental parameters are listed.

Grothaus, M. G.↗
NASA NTRS1989

Structural and thermal response of 30 cm diameter ion thruster optics

Tabular and graphical data are presented which are intended for use in calibrating and validating structural and thermal models of ion thruster optics. A 30 cm diameter, two electrode, mercury ion thruster was operated using two different electrode assembly designs. With no beam extraction, the transient and steady state temperature profiles and center electrode gaps were measured for three discharge powers. The data showed that the electrode mount design had little effect on the temperatures, but significantly impacted the motion of the electrode center. Equilibrium electrode gaps increased with one design and decreased with the other. Equilibrium displacements in excess of 0.5 mm and gap changes of 0.08 mm were measured at 450 W discharge power. Variations in equilibrium gaps were also found among assemblies of the same design. The presented data illustrate the necessity for high fidelity ion optics models and development of experimental techniques to allow their validation.

Macrae, G. S.↗
NASA NTRS1989

Evaluation of the resiliency characteristics of several candidate Solid Rocket Booster O-ring materials

Resiliency tests have been conducted in order to evaluate O-ring sealing response in the revised Space Shuttle SRBs, giving attention to the effects of temperature and gap-opening rates. Additional testing was conducted to ascertain O-ring responses to simulated SRB field-joint deflections. All tests employed a face-seal fixture mounted on a servohydraulic apparatus. The Viton candidate O-ring material tracked the gap-opening rate better at higher temperatures and lower gap-opening rates; it was also the only material inert to the calcium grease employed. Heaters must be used to maintain the 70 F minimum temperature at which the Viton O-ring will track the required gap opening rate.

Lach, C. L.↗
NASA NTRS1989

Polar cap deflation during magnetospheric substorms

The expanding/contracting polar cap model has been used to simulate DE-2 ion drift data during substorms as determined using the AL index. Of the 39 cases modeled, 57 percent required the opening of a nightside gap which maps to where reconnection occurs in the tail; 75 percent of the 16 recovery phase cases required a nightside gap, while only 29 percent of the 17 expansion phase cases required a nightside gap. On the basis of this result, it is concluded that if a nightside gap implies tail reconnection, then reconnection probably occurs after expansion phase onset and continues throughout most of the recovery phase of a substorm.

Moses, J. J.↗