Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLUID MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

An intelligent data acquisition system for fluid mechanics research

This paper describes a novel data acquisition system for use with wind-tunnel probe-based measurements, which incorporates a degree of specific fluid dynamics knowledge into a simple expert system-like control program. The concept was developed with a rudimentary expert system coupled to a probe positioning mechanism operating in a small-scale research wind tunnel. The software consisted of two basic elements, a general-purpose data acquisition system and the rulebased control element to take and analyze data and supplying decisions as to where to measure, how many data points to take, and when to stop. The system was validated in an experiment involving a vortical flow field, showing that it was possible to increase the resolution of the experiment or, alternatively, reduce the total number of data points required, to achieve parity with the results of most conventional data acquisition approaches.

Cantwell, E. R.↗

Fluidity and supercriticality of the QCD matter created in relativistic heavy ion collisions

In this paper we discuss the fluidity of the hot and dense QCD matter created in ultrarelativistic heavy ion collisions in comparison with various other fluids and, in particular, suggest its possible supercriticality. After examining the proper way to compare nonrelativistic and relativistic fluids from both thermodynamic and hydrodynamic perspectives, we propose a new fluidity measure that shows certain universality for a remarkable diversity of critical fluids. We then demonstrate that a fluid in its supercritical regime has its fluidity considerably enhanced. This result may suggest a possible relationship between the seemingly good fluidity of the QCD matter produced in heavy ion collisions at a center-of-mass energy of sq root(s)=200A GeV and the supercriticality of this matter with respect to the critical end point on the QCD phase diagram. Based on this observation, we predict an even better fluidity of the matter to be created in heavy ion collisions at Large Hadron Collider energies and the loss of good fluidity at certain, lower beam energy. Finally, based on our criteria, we analyze the suitability of a hydrodynamic description for the fireball evolution in heavy ion collisions at various energies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

100 s extraction of negative ion beams by using actively temperature-controlled plasma grid

Long pulse beam extraction with a current density of 120 A/m{sup 2} for 100 s has been achieved with a newly developed plasma grid (PG) for the JT-60SA negative ion source which is designed to produce high power and long pulse beams with a negative ion current of 130 A/m{sup 2} (22 A) and a pulse length of 100 s. The PG temperature is regulated by fluorinated fluids in order to keep the high PG temperature for the cesium-seeded negative ion production. The time constant for temperature controllability of the PG was measured to be below 10 s, which was mainly determined by the heat transfer coefficient of the fluorinated fluid. The measured decay time of the negative ion current extracted from the actively temperature-controlled PG was 430 s which was sufficient for the JT-60SA requirement, and much longer than that by inertial-cooling PG of 60 s. Obtained results of the long pulse capability are utilized to design the full size PG for the JT-60SA negative ion source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sizing of colloidal particle and protein molecules in a hanging fluid drop

We report non-invasive particle size measurements of polystyrene latex colloidal particles and bovine serum albumin (BSA) protein molecules suspended in tiny hanging fluid drops of 30 micro-Liter volume using a newly designed fiber optic probe. The probe is based upon the principles of the technique of dynamic light scattering (DLS). The motivation for this work comes from growing protein crystals in outer space. Protein crystals have been grown previously in hanging drops in microgravity experiments on-board the space shuttle orbiter. However, obtaining quantitative information on nucleation and growth of the protein crystals in real time has always been a desired goal, but hitherto not achieved. Several protein researchers have shown interest in using DLS to monitor crystal growth process in a droplet, but elaborate instrumentation and optical alignment problems have made in-situ applications difficult. We demonstrate that such an experiment is now possible. Our system offers fast (5 seconds) determination of particle size, utilize safe levels of very low laser power (less than or equal to 0.2 mW), a small scattering volume (approximately 2 x 10(exp -5) cu mm) and high spatial coherence (Beta) values. This is a major step forward when compared to currently available DLS systems.

Ansari, Rafat R.↗

Improved Venus ionopause altitude calculation and comparison with measurement

Improved approximations are incorporated into the inviscid fluid method originated by Spreiter et al (1970) in calculations of the altitude of the Venus ionopause. The altitude calculations are then compared with median altitudes measured by the Pioneer Venus retarding potential analyzer. The calculated ionopause shape is found to closely approximate the measured meridian shape in the solar zenith angle (SZA) range of zero-135 deg. The use of improved ionospheric pressure field ionosheath pressure and Prandtl-Meyer expansion approximations lowers the terminator ionopause altitude to approximately half that obtained with the usual Spreiter approximations. It is also determined that the calculated dawn ionopause is about 300 km higher than the dusk ionopause, and that both ionopauses are close to their respective measured meridian values. It is concluded that median ionopause altitude within the SZA angle range may be calculated without inclusion of a viscous interaction in the theory.

Knudsen, W. C.↗

Estimating perturbed stress from 3-D borehole displacements induced by fluid injection in fractured or faulted shales

SUMMARY Hydrofracturing stress measurements in fractured and anisotropic shales are notoriously difficult, because opening of existing geological features tends to prevent the creation of a pure hydraulic fracture perpendicular to the least compressive principal stress. Here we show how adding 3-D borehole-displacement measurements while conducting the hydraulic injection test helps to better constrain the principal stress orientations and magnitudes. We developed a 3-D fully coupled hydromechanical numerical model to analyse the displacement, fluid pressure and injection flow-rate data measured during an injection pressure-step-rate test conducted to activate a faulted borehole interval in the Mont Terri Opalinus Clay (Switzerland). We find that injected fluids can only penetrate the fault when it is at or above the Coulomb failure pressure. Borehole displacement orientations are sensitive to a ∼15° variation in the stress–tensor orientation and a 1 MPa stress magnitude variation. Although some dispersion occurs while rupture is propagating along the fault plane ∼4 m away from the borehole, the maximum density of displacement orientations consistently informs about the stress orientation. Thus, an extended injection step-rate approach coupled with an accurate in situ measurement of the borehole wall displacements can be used to better constrain the local stress field perturbations in fractured shales and in heterogeneous rock in general.

Guglielmi, Yves↗

An optical study of grain formation: Casting and solidification technology (2-IML-1)

By studying the unidirectional growth of a metal-model material in microgravity, an attempt is made to characterize alloy solidification. Using holograms and supporting temperature measurements obtained during processing in the Fluids Experiment System (FES), the solute and thermal fields associated with the dendrite growth front and extraneous nucleation will be measured and compared to a theoretical (computational) model. Ground based supporting experiments include particle tracking to measure the velocity fields, and optical phase shift techniques (confocal optical signal processing, interferometry, and Schlieren) to study thermal and solutal fields.

Mccay, Mary H.↗

Modeling of Slosh Dynamics in Cryogenic Propellant Tanks in Microgravity Environments

The slosh dynamics in cryogenic fuel tanks under microgravity is a pressing problem that severely affects the reliability of launching spacecraft. After reaching low Earth orbit, the propellant in a multistage rocket experiences large and cyclic changes in temperature as a result of solar heating. Tank wall heating can induce thermal stratification and propellant boiloff, particularly during slosh-inducing vehicle maneuvers. Precise understanding of the dynamic and thermodynamic effects of propellant slosh caused by these maneuvers is critical to mission performance and success. Computational fluid dynamics (CFD) analysis is used extensively within the space vehicle industry in an attempt to characterize the behavior of liquids in microgravity, yet experimental data to quantify these predictions is very limited and reduces confidence in the analytical predictions. A novel approach designed to produce high-fidelity data for correlation to CFD model predictions is being developed with the assistance of Florida Institute of Technology (FIT) and Sierra Lobo, Inc. With few exceptions, previous work in slosh dynamics was theoretical or treated the mass of fuel as a variable of inertia only; such models did not consider the viscosity, surface tension, or other important fluid effects. The challenges in this research are in the development of instrumentation able to measure the required parameters, the computational ability to quantify the fluid behaviors, and the means to assess both the measurements and predictions. The design of this experiment bridges the understanding of slosh dynamics in microgravity by a comprehensive approach that combines CFD tools, dynamic simulation tools, semianalytical models of the predominant fluid effects, and an experimental framework that includes measurement and characterization of liquid slosh in one-degree-of-freedom (DOF) and two-DOF experiments, and ultimately experiments in a NASA low-gravity aircraft.

Source record↗

In situ multipurpose time-resolved spectrometer for monitoring nanoparticle generation in a high-pressure fluid

We developed a multipurpose time-resolved spectrometer for studying the dynamics of nanoparticles generated by pulsed-laser ablation (PLA) in a high-pressure fluid. The apparatus consists of a high-pressure optical cell and three spectrometers for in situ measurements. The optical cell was designed for experiments at temperatures up to 400 K and pressures up to 30 MPa with fluctuations within {+-}0.1% h{sup -1}. The three spectrometers were used for the following in situ measurements at high pressures: (i) transient absorption spectrum measurements from 350 to 850 nm to investigate the dynamics of nanoparticle generation from nanoseconds to milliseconds after laser irradiation, (ii) absorption spectrum measurements from 220 to 900 nm to observe the time evolution of nanoparticles from seconds to hours after laser ablation, and (iii) dynamic light scattering measurements to track nanoparticles with sizes from 10 nm to 10 {mu}m in the time range from seconds to hours after laser ablation. By combining these three spectrometers, we demonstrate in situ measurements of gold nanoparticles generated by PLA in supercritical fluids. This is the first report of in situ time-resolved measurements of the dynamics of nanoparticles generated in a supercritical fluid.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Feasibility of Electrostriction for Measurement of the Critical Temperature in the Critical Viscosity Experiment

The large compressibility of a pure fluid near its critical point is a potential means of measuring the critical temperature. At the suggestion of Prof. Ferrell we observed electrostriction in xenon by applying a large voltage across a small, open capacitor immersed in the sample and then measuring the capacitance change caused by the subsequent increase in the xenon's local density. This scheme was attractive because the compressibility is a large, well-understood effect and because we were already familiar with low-voltage capacitance measurements. We found qualitative agreement with our initial expectations based on the fluid's compressibility. However, we also found an additional effect comparable in size to the expected electrostriction but proportional to the applied voltage. We have no explanation for this effect. Thus, given the Science Panel's recommendation against investing extensive effort in this direction, we are abandoning further development of an alternate means for measuring the critical temperature.

Berg, Robert F.↗

Results from the Radio Frequency Mass Gauge Technology Demonstration on the Intuitive Machines Nova-C Lunar Lander

A cryogenic propellant mass gauge known as the Radio Frequency Mass Gauge (RFMG) was integrated into the Intuitive Machines (IM) Nova-C lunar lander and provided an estimate of the liquid oxygen and liquid methane mass in the lander propellant tanks throughout the IM-1 mission, including during microgravity coast phases. An RFMG electronics controller was used to measure and record the spectrum of the RF signal reflected from an antenna sensor in each tank over the frequency range 100 to 1,300 MHz. The RF spectrum of each of the tanks is unique and is sensitive to the index of refraction of the propellants and the spatial distribution of the liquid within the tanks. Electromagnetic simulation software was used to simulate the antenna response spectra for a given tank geometry, fluid properties, and liquid–vapor configurations within the tank. Over 10,000 antenna response simulations were completed for each propellant tank prior to the IM-1 mission and represented various volumetric fill levels and fluid configurations. The simulated spectra served as a database against which measured tank spectra were compared. For analysis, a spectral matching algorithm was used to find the best match between measured and simulated spectra, and the gauged mass was calculated from the most highly correlated fluid mass simulations. RFMG measurements were recorded during tank loading on the launch pad and during translunar coast, lunar orbit insertion, low lunar orbit, powered descent to the lunar surface, and postlanding on the Moon. This paper describes the RF and fluid simulations, the RFMG measurements and analysis of spectral data, the RFMG instrument, and the gauged results throughout all phases of the IM-1 mission.

lunar lander↗

Results from the Radio Frequency Mass Gauge Technology Demonstration on the Intuitive Machines Nova-C Lunar Lander

A cryogenic propellant mass gauge known as the Radio Frequency Mass Gauge (RFMG) was integrated into the Intuitive Machines (IM) Nova-C lunar lander and provided an estimate of the liquid oxygen and liquid methane mass in the lander propellant tanks throughout the IM-1 mission, including during microgravity coast phases. An RFMG electronics controller was used to measure and record the spectrum of the RF signal reflected from an antenna sensor in each tank over the frequency range 100 to 1,300 MHz. The RF spectrum of each of the tanks is unique and is sensitive to the index of refraction of the propellants and the spatial distribution of the liquid within the tanks. Electromagnetic simulation software was used to simulate the antenna response spectra for a given tank geometry, fluid properties, and liquid–vapor configurations within the tank. Over 10,000 antenna response simulations were completed for each propellant tank prior to the IM-1 mission and represented various volumetric fill levels and fluid configurations. The simulated spectra served as a database against which measured tank spectra were compared. For analysis, a spectral matching algorithm was used to find the best match between measured and simulated spectra, and the gauged mass was calculated from the most highly correlated fluid mass simulations. RFMG measurements were recorded during tank loading on the launch pad and during translunar coast, lunar orbit insertion, low lunar orbit, powered descent to the lunar surface, and postlanding on the Moon. This paper describes the RF and fluid simulations, the RFMG measurements and analysis of spectral data, the RFMG instrument, and the gauged results throughout all phases of the IM-1 mission.

lunar lander↗

The solubility of NdPO 4 and DyPO 4 and stability of Nd and Dy chloride and hydroxyl complexes as a function of pH and salinity to 450 °C

The mobility of rare earth elements (REE) in geological systems is often controlled by the stability of monazite and xenotime, which are important hosts for the light and heavy REE. These REE phosphates constitute important resources and provide information on ore formation conditions and timing due to their uses as geothermometers and geochronometers. While the thermodynamic properties for these minerals are well-established up to high temperature and pressure, the properties for the aqueous REE complexes are not well constrained with limited information up to 300 °C. In this study, the solubility of synthetic NdPO 4 and DyPO 4 endmembers were measured in hydrothermal sub- to supercritical NaCl-bearing aqueous solutions from 350 at saturated water vapor pressure to 450 °C at 700 bar. The speciation of Nd and Dy was determined in acidic to alkaline solutions (pH 25 °C values from 2 to 10), and indicates that the hydroxyl species REE(OH) 2 + and REE(OH) 3 0 predominate at low salinity (0.01 mol/kg NaCl) with some contribution of REE chloride species REECl 2+ and REECl 2 + in acidic fluids. The REE phosphate solubility measured in these experiments is up to two orders of magnitude higher than predicted using existing thermodynamic properties from literature for aqueous species extrapolated from lower temperature data to supercritical conditions. To address this discrepancy, the thermodynamic properties of the REE aqueous species were optimized using GEMSFITS to derive the formation constants for the REE chloride (β Cl ) and hydroxyl (β OH ) complexes in the studied temperature range. This study highlights the importance of the hydroxyl species REE(OH) 2 + and REE(OH) 3 0 over a wide range of pH and temperature. As a result, the revised thermodynamic properties for Dy and Nd chloride and hydroxyl species more accurately predict the solubility of NdPO 4 and DyPO 4 and provide insight into the speciation and mobility of the light and heavy REE in hydrothermal supercritical fluids in the crust.

58 GEOSCIENCES↗

Temperature Homogeneity under Selective and Localized Microwave Heating in Structured Flow Reactors

Selective heating of different phases of multiphase systems via microwaves can result in energy savings and suppression of side reactions. However, materials properties and operating conditions that maximize temperature gradients are poorly understood. Here we utilize computational fluid dynamics (CFD) computations and temperature measurements in structured flow reactors (monoliths) in a monomodal microwave cavity to assess the temperature difference between the walls and the fluid and develop a simple lumped model to estimate when temperature gradients exist. We also explore the material’s thermal and electrical properties of structured reactors for isothermal catalyst conditions. We propose that CFD simulations can be used as a nonintrusive, predictive tool of temperature homogeneity. Importantly, we demonstrate that localized heating in the bed under several conditions rather than selective heating is responsible for the selectivity enhancement. Furthermore, our results indicate that structured beds made of high thermal conductivity materials avoid arcing and enable temperature homogeneity and low electrical conductivity materials allow microwaves to penetrate the domain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface Temperature Effect on Convective Heat Transfer Coefficients for Jet Impingement Cooling of Electric Machines with Automatic Transmission Fluid: Preprint

In this study, the results of NREL's continued work on experimental characterization of the thermal performance of free-surface jets of automatic transmission fluid impinged on a heated target surface are presented. The measured heat transfer coefficients are useful for understanding factors influencing performance of driveline fluid-based cooling systems for electric machines and help designers in developing high-performance, power-dense and reliable machines. Experiments were carried out for different fluid and target surface temperatures (50 degrees C, 70 degrees C, and 90 degrees C for the fluid and 90 degrees C, 100 degrees C, 110 degrees C, and 120 degrees C for the target surface). Impinging jet velocities (0.5 m/s to 7.5 m/s) and the jet position on the target surface (center versus edge) were also varied. The impinging angle was kept at 90 degrees relative to the target surface. It was found that higher target surface temperature increased heat transfer coefficients, namely, increasing surface temperature from 90 degrees C to 120 degrees C enhanced heat transfer coefficient values at higher impinged jet velocities (7.5 m/s) by up to 15%.

33 ADVANCED PROPULSION SYSTEMS↗

Fluid and kinetic nonlinearities of near-acoustic plasma waves

Large amplitude, near-acoustic plasma waves have a temperature-dependent harmonic content and nonlinear frequency shifts. On cold plasmas, experiments show that fluid nonlinearities dominate, and the observed harmonic content is well predicted by a recent fluid analysis. In contrast, the measured nonlinear frequency shift is smaller than this theory prediction, suggesting the presence of other nonlinear effects neglected in this analysis. When the plasma is heated, kinetic effects become important, and we observe an increase in both the harmonic content and nonlinear frequency shift. Quantitative experiments on the stability of these large amplitude, near-acoustic plasma waves strongly support the idea that trapped particles reduce the amplitude threshold for instability below fluid models. Furthermore, at low temperatures, the broad characteristics of the parametric instability are determined by the frequency detuning of the pump and daughter wave and the wave-wave coupling strength, surprisingly consistent with simple cold fluid, three-wave theories. However, at higher temperatures, the pump wave becomes unstable at half the threshold pump wave amplitude, with similar exponential growth rates as for a cold plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

In situ quantification of fracture slip induced by hydraulic injections in a deep borehole: A comparison of two different borehole techniques

In situ measurements of fracture deformation during fluid injection are rare, yet essential for understanding the mechanical response of fractured rock. In this study, we evaluate the reliability of two methods by comparing their slip vector estimates: high-resolution borehole acoustic televiewer images captured before and after injection tests, and displacement data from a three-component borehole deformation probe recorded during the injections. Acoustic televiewer images capture only final in-plane displacement, whereas three-component borehole deformation measurements provide full 3D, transient fracture movement. Four injection tests in a fractured granitic rock mass along an inclined borehole at the Bedretto Underground Laboratory (Switzerland), beneath more than 1100 m of overburden, were analyzed. The two methods yielded consistent kinematics and comparable slip magnitudes, typically in the range of 0.2 – 0.6 mm. Angular differences between estimated slip directions ranged from 0.2° to 28°. For two test intervals with pre-existing fractures optimally oriented for slip, the measured slip vectors agreed with forward-modeled slip vectors based on the regional in situ stress field, supporting the Wallace–Bott hypothesis. Measurable shear displacement was identified in two test intervals containing fractures oriented nearly perpendicular to the least principal stress, including a newly formed hydraulic fracture. This demonstrates that even fractures unfavorably oriented for slip can undergo shear due to local stress perturbations around an inclined borehole.

Acoustic televiewer↗

Turbidity of a Binary Fluid Mixture: Determining Eta

A ground based (1-g) experiment is in progress that will measure the turbidity of a density-matched, binary fluid mixture extremely close to its liquid-liquid critical point. By covering the range of reduced temperatures t equivalent to (T-T(sub c)) / T(sub c) from 10(exp -8) to 10(exp -2), the turbidity measurements will allow the critical exponent eta to be determined. No experiment has precisely determined a value of the critical exponent eta, yet its value is significant to theorists in critical phenomena. Relatively simple critical phenomena, as in the liquid-liquid system studied here, serve as model systems for more complex systems near a critical point.

Jacobs, Donald T.↗