Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAT PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Direct Numerical Simulation of Acoustic Disturbances in the Rectangular Test Section of a Hypersonic Wind Tunnel

Direct numerical simulations (DNS) of the full-scale rectangular nozzle of a hypersonic wind tunnel are conducted to study the acoustic freestream fluctuations radiating from turbulent boundary layers (TBLs) along the nozzle walls. The nozzle geometry and the flow conditions of the DNS match those of the NASA 20-Inch Mach 6 Tunnel, and the DNS has been completed for a domain without spanwise sidewall boundary conditions. The turbulent boundary layer parameters based on the DNS compare well with those derived from Reynolds Averaged Navier-Stokes (RANS) calculations as well as with the predictions based on Pate’s correlation. A similarly good comparison is observed for both the Mach number distribution and the Reynold’s stresses obtained from the DNS and RANS calculations, respectively. Various characteristics of the acoustic pressure fluctuations within the inviscid core of the nozzle flow are compared with those associated with a single flat plate at a similar freestream Mach number. The frequency spectrum and bulk propagation speeds match well between the nozzle and the flat plate, but the rms pressure fluctuation is higher for the nozzle configuration, likely due to the combined effect of acoustic radiation from the top and bottom walls. Spatial contours of the two-point correlation coefficient display elliptical tails with approximately equal but opposite angles corresponding to the preferred directionality of acoustic structures radiated from both walls. Future work will focus on DNS of the full nozzle configuration, including the effects of the nozzle side walls.

Deegan, Cole P.↗

Orbiter BLT Flight Experiment Wind Tunnel Simulations: Nearfield Flowfield Imaging and Surface Thermography

This paper reports a series of wind tunnel tests simulating the near-field behavior of the Space Shuttle Orbiter Boundary Layer Transition Detailed Test Objective (BLT DTO) flight experiment. Hypersonic flow over a flat plate with an attached BLT DTO-shaped trip was tested in a Mach 10 wind tunnel. The sharp-leading-edge flat plate was oriented at an angle of 20 degrees with respect to the freestream flow, resulting in post-shock edge Mach number of approximately 4. The flowfield was visualized using nitric oxide (NO) planar laser-induced fluorescence (PLIF). Flow visualizations were performed at 10 Hz using a wide-field of view and high-resolution NO PLIF system. A lower spatial resolution and smaller field of view NO PLIF system visualized the flow at 500 kHz, which was fast enough to resolve unsteady flow features. At the lowest Reynolds number studied, the flow was observed to be laminar and mostly steady. At the highest Reynolds number, flow visualizations showed streak instabilities generated immediately downstream of the trip. These instabilities transitioned to unsteady periodic and spatially irregular structures downstream. Quantitative surface heating imagery was obtained using the Temperature Sensitive Paint (TSP) technique. Comparisons between the PLIF flow visualizations and TSP heating measurements show a strong correlation between flow patterns and surface heating trends.

Danehy, Paul M.↗

Ice Growth Model for Polar Water Capture Systems

In-situ resource utilization (ISRU) is essential to NASA’s goal of sustainable and cost-effective missions to the Moon and beyond. Water has become a particular source of interest since its discovery in the permanently shadowed regions (PSRs) of the Moon. This water exists as ice bound within the regolith, so one mode of capture is heating to sublimation temperatures and capturing at very low pressure. It then can be stored in ice form and transported out of the PSR and to a sunlit ridge, where processes such as electrolysis can be performed[2]. An understanding of frost growth dynamics under rarefied conditions is necessary for successful water capture and storage due to transient thermal properties of frost. A Diffusion-Limited Aggregation (DLA) approach was taken to analytically model bulk thermal conductivity changes of the growing frost layer under varying wall temperatures and frost layer porosities. The model utilizes well-known correlations for effective thermal conductivity and records the values as the frost layer thickness increases. This thermal conductivity can be applied to a known temperature change and be used to evaluate heat flux through the combined frost layer and tank wall for either a flat plate or cylindrical geometry. An experiment is described that will evaluate this model using one-dimensional frost growth on a horizontal, flat plate under low-pressure. The ice growth will be measured using a millimeter-scale photogrammetry camera system and a load cell measured transient mass growth.

In situ Resource Utilization↗

Ice Growth Model for Polar Water Capture Systems

In-situ resource utilization (ISRU) is essential to NASA’s goal of sustainable and cost-effective missions to the Moon and beyond. Water has become a particular source of interest since its discovery in the permanently shadowed regions (PSRs) of the Moon. This water exists as ice bound within the regolith, so one mode of capture is heating to sublimation temperatures and capturing at very low pressure. It then can be stored in ice form and transported out of the PSR and to a sunlit ridge, where processes such as electrolysis can be performed[2]. An understanding of frost growth dynamics under rarefied conditions is necessary for successful water capture and storage due to transient thermal properties of frost. A Diffusion-Limited Aggregation (DLA) approach was taken to analytically model bulk thermal conductivity changes of the growing frost layer under varying wall temperatures and frost layer porosities. The model utilizes well-known correlations for effective thermal conductivity and records the values as the frost layer thickness increases. This thermal conductivity can be applied to a known temperature change and be used to evaluate heat flux through the combined frost layer and tank wall for either a flat plate or cylindrical geometry. An experiment is described that will evaluate this model using one-dimensional frost growth on a horizontal, flat plate under low-pressure. The ice growth will be measured using a millimeter-scale photogrammetry camera system and a load cell measured transient mass growth.

ice growth↗

Analysis of Free-Flight Laminar, Transitional, and Turbulent Heat-Transfer Results at Free-Stream Mach Numbers Near 20 (Reentry F)

Laminar, transitional, and turbulent heat-transfer data were measured during a reentry flight at a Mach number of 20 on a 5 deg half-angle cone 3.962 m (13 ft) long with an initial nose tip radius of 0.254 cm (0.1 in.). The free-stream Reynolds number increased during the prime data period from 7.0 x 10(exp 6) to 51.5 x 10(exp 6) per meter (2.1 x 10(exp 6) to 15.7 x 10(exp 6) per foot) and the ratio of wall to total temperature varied from 0.053 to 0.12. The angle of attack was less than 1deg for the prime data period. The experimental laminar and turbulent heating rates are compared with results from existing flat-plate prediction methods. At conditions of minimal tip blunting and angle of attack (above 26.8 km (88 000 ft)), values from a flat-plate laminar method agreed within 20 percent with the laminar data. The Schultz-Grunow skin-friction equation with reference enthalpy; conditions, with the Reynolds number based on distance from the transition location, and with the Colburn Reynolds analogy agreed within 10 percent with the experimental turbuleiit heating data. The Van Driest n skin-friction equation with Reynolds number greater than 10(exp 7) based on distance from the peak heating point and the Colburn Reynolds analogy was also within approximately 10 percent of the experimental turbulent heating data. A data correlation jbf the extent of transition and a simple empirical transition-zone heating correlation were also presented.

Zoby, Ernest V.↗

Jet decay rate effects on hover jet-induced loads

The paper explains the mechanisms for observed jet decay rate effects on jet-induced loads on a flat plate for cross-flow and hover configurations. Examples are presented for the influence of the decay rate on integrated loads on a flat plate induced by the jet issuing at a right angle from the plate into still air; knowledge of these jet-induced loadings is of particular importance for VTOL aircraft design because they produce an effective loss in the lift force available in hover. The apparent inconsistency between existing lift loss vs jet decay rate trends is explained in light of the different mechanism which determine the jet mixing and trajectory, i.e., entrainment, blockage, and the vortex pair associated with a jet in crossflow.

Kuhlman, J. M.↗

Wall mass transfer and pressure gradient effects on turbulent skin friction

The effects of mass injection and pressure gradients on the drag of surfaces were studied theoretically with the aid of boundary-layer and Navier-Stokes codes. The present investigation is concerned with the effects of spatially varying the injection in the case of flat-plate drag. Effects of suction and injection on wavy wall surfaces are also explored. Calculations were performed for 1.2 m long surfaces, one flat and the other sinusoidal with a wavelength of 30.5 cm. Attention is given to the study of the effect of various spatial blowing variations on flat-plate skin friction reduction, local skin friction coefficient calculated by finite difference boundary-layer code and Navier-Stokes code, and the effect of phase-shifting sinusoidal mass transfer on the drag of a sinusoidal surface.

Watson, R. D.↗

Technology developments toward 30-year-life of photovoltaic modules

As part of the United States National Photovoltaics Program, the Jet Propulsion Laboratory's Flat-Plate Solar Array Project (FSA) has maintained a comprehensive reliability and engineering sciences activity addressed toward understanding the reliability attributes of terrestrial flat-plate photovoltaic arrays and to deriving analysis and design tools necessary to achieve module designs with a 30-year useful life. The considerable progress to date stemming from the ongoing reliability research is discussed, and the major areas requiring continued research are highlighted. The result is an overview of the total array reliability problem and of available means of achieving high reliability at minimum cost.

Ross, R. G., Jr.↗

Stability of axisymmetric boundary layers on sharp cones at hypersonic Mach numbers

The stability of sharp-cone boundary layers at zero angle of attack is investigated. Standard linear stability theory is used to perform a numerical study at an edge Mach number M(e) of 6.8 of normal-mode stability characteristics on an adiabatic-wall cone with special reference to the conditions of the stability experiment of Stetson et al. (1983). Comparisons of the calculations with experimental measurements bring out major areas of disagreement which remain to be resolved even in this simple case. Finally, a series of calculations of both cone and flat-plate N factors at M(e) of 4.5, 5.8, and 6.8 is used to study the relation between transition on a cone and flat plate based on stability theory.

Mack, Leslie M.↗

Receptivity of Supersonic Boundary Layers to Acoustic Disturbances

Boundary layer receptivity to two-dimensional slow and fast acoustic waves is investigated by solving Navier-Stokes equations for Mach 4.5 flow over a flat plate with a finite-thickness leading edge. Higher order spatial and temporal schemes are employed to obtain the solution whereby the flat-plate leading edge region is resolved by providing a sufficiently refined grid. The results show that the instability waves are generated in the leading edge region and that the boundary-layer is much more receptive to slow acoustic waves (by almost a factor of 20) as compared to the fast waves. Hence, this leading-edge receptivity mechanism is expected to be more relevant in the transition process for high Mach number flows. The effect of acoustic wave incidence angle is also studied and it is found that the receptivity of the boundary layer on the windward side (with respect to the acoustic forcing) decreases by more than a factor of 4 when the incidence angle is increased from 0 to 45 deg. However, the receptivity coefficient for the leeward side is found to vary relatively weakly with the incidence angle. The effect of leading-edge thickness is also studied and bluntness is found to stabilize the boundary layer. The relative significance of fast acoustic waves is enhanced in the presence of bluntness.

Malik, Mujeeb R.↗

Acoustic Receptivity of Mach 4.5 Boundary Layer with Leading- Edge Bluntness

Boundary layer receptivity to two-dimensional slow and fast acoustic waves is investigated by solving Navier-Stokes equations for Mach 4.5 flow over a flat plate with a finite-thickness leading edge. Higher order spatial and temporal schemes are employed to obtain the solution whereby the flat-plate leading edge region is resolved by providing a sufficiently refined grid. The results show that the instability waves are generated in the leading edge region and that the boundary-layer is much more receptive to slow acoustic waves (by almost a factor of 20) as compared to the fast waves. Hence, this leading-edge receptivity mechanism is expected to be more relevant in the transition process for high Mach number flows where second mode instability is dominant. Computations are performed to investigate the effect of leading-edge thickness and it is found that bluntness tends to stabilize the boundary layer. Furthermore, the relative significance of fast acoustic waves is enhanced in the presence of bluntness. The effect of acoustic wave incidence angle is also studied and it is found that the receptivity of the boundary layer on the windward side (with respect to the acoustic forcing) decreases by more than a factor of 4 when the incidence angle is increased from 0 to 45 deg. However, the receptivity coefficient for the leeward side is found to vary relatively weakly with the incidence angle.

Malik, Mujeeb R.↗

Analysis of liquid-metal-jet impingement cooling in a corner region and for a row of jets

A conformal mapping method was used to analyze liquid-metal-jet impingement heat transfer. The jet flow region and energy equation are transformed to correspond to uniform flow in a parallel plate channel with nonuniform heat addition along a portion of one wall. The exact solution for the wall-temperature distribution was obtained in the transformed channel, and the results are mapped back into the physical plane. Two geometries are analyzed. One is for a single slot jet directed either into an interior corner formed by two flat plates, or over the external sides of the corner; the flat plates are uniformly heated, and the corner can have various included angles. The heat-transfer coefficient at the stagnation point at the apex of the plates is obtained as a function of the corner angle, and temperature distributions are calculated along the heated walls. The second geometry is an infinite row of uniformly spaced parallel slot jets impinging normally against a uniformly heated plate. The heat-transfer behavior is obtained as a function of the spacing between the jets. Results are given for several jet Peclet numbers from 5 to 50.

Siegel, R.↗

Application of the method of integral relations to laminar boundary layers in three dimensions

The method of integral relations is extended to general three-dimensional compressible laminar boundary layer flows. The transformation employed to transform the basic three-dimensional compressible boundary layer equations into quasi-incompressible form is an extension of the Howarth transformation. The resulting system of differential equations is integrated numerically by the method of integral relations as proposed by Dorodnitsyn. To demonstrate the accuracy of the method, it is applied to calculation of the parabolic flow over a flat plate and the boundary flow over an infinite yawed cylinder, for which solutions are known. It is then applied to the flow over a flat plate disturbed by a cylinder normal to the plate, for which a finite-difference solution is available for comparison. It is finally applied to calculating the crossflow velocity variation for supersonic flow over a swept wedge.

Holt, M.↗

Effects of Reynolds number on orifice induced pressure error

Data previously reported for orifice induced pressure errors are extended to the case of higher Reynolds number flows, and a remedy is presented in the form of a porous metal plug for the orifice. Test orifices with apertures 0.330, 0.660, and 1.321 cm in diam. were fabricated on a flat plate for trials in the NASA Langley wind tunnel at Mach numbers 0.40-0.72. A boundary layer survey rake was also mounted on the flat plate to allow measurement of the total boundary layer pressures at the orifices. At the high Reynolds number flows studied, the orifice induced pressure error was found to be a function of the ratio of the orifice diameter to the boundary layer thickness. The error was effectively eliminated by the insertion of a porous metal disc set flush with the orifice outside surface.

Plentovich, E. B.↗

Gust Acoustics Computation with a Space-Time CE/SE Parallel 3D Solver

The benchmark Problem 2 in Category 3 of the Third Computational Aero-Acoustics (CAA) Workshop is solved using the space-time conservation element and solution element (CE/SE) method. This problem concerns the unsteady response of an isolated finite-span swept flat-plate airfoil bounded by two parallel walls to an incident gust. The acoustic field generated by the interaction of the gust with the flat-plate airfoil is computed by solving the 3D (three-dimensional) Euler equations in the time domain using a parallel version of a 3D CE/SE solver. The effect of the gust orientation on the far-field directivity is studied. Numerical solutions are presented and compared with analytical solutions, showing a reasonable agreement.

Wang, X. Y.↗

Skin friction reduction in supersonic flow by injection through slots, porous sections and combinations of the two

An experimental study of skin friction reduction in a Mach 3.0 air steam with gaseous injection through a tangential slot, a porous wall section, and combinations of the two was conducted. The primary data obtained were wall shear values measured directly with a floating element balance and also inferred from Preston Tube measurements. Detailed profiles at several axial stations, wall pressure distributions and schlieren photographs are presented. The data indicate that a slot provides the greatest skin friction reduction in comparison with a reference flat plate experiment. The porous wall section arrangement suffers from an apparent roughness-induced rise in skin friction at low injection rates compared to the flat plate. The combination schemes demonstrated a potential for gain.

Schetz, J. A.↗

Free-stream turbulence and concave curvature effects on heated, transitional boundary layers

An experimental investigation of the transition process on flat-plate and concave curved-wall boundary layers for various free-stream turbulence levels was performed. Results show that for transition of a flat-plate, the two forms of boundary layer behavior, identified as laminar-like and turbulent-like, cannot be thought of as separate Blasius and fully-turbulent profiles, respectively. Thus, simple transition models in which the desired quantity is assumed to be an average, weighted on intermittency, of the theoretical laminar and fully turbulent values is not expected to be successful. Deviation of the flow identified as laminar-like from theoretical laminar behavior is shown to be due to recovery after the passage of a turbulent spot, while deviation of the flow identified as turbulent-like from the full-turbulent values is thought to be due to incomplete establishment of the fully-turbulent power spectral distribution. Turbulent Prandtl numbers for the transitional flow, computed from measured shear stress, turbulent heat flux and mean velocity and temperature profiles, were less than unity. For the curved-wall case with low free-stream turbulence intensity, the existence of Gortler vortices on the concave wall within both laminar and turbulent flows was established using liquid crystal visualization and spanwise velocity and temperature traverses. Transition was found to occur via a vortex breakdown mode. The vortex wavelength was quite irregular in both the laminar and turbulent flows, but the vortices were stable in time and space. The upwash was found to be more unstable, with higher levels of u' and u'v', and lower skin friction coefficients and shape factors. Turbulent Prandtl numbers, measured using a triple-wire probe, were found to be near unity for all post-transitional profiles, indicating no gross violation of Reynolds analogy. No evidence of streamwise vortices was seen in the high turbulence intensity case.

Kim, J.↗

Fluctuating pressures in flow fields of jets

The powered lift configurations under present development for STOL aircraft are the externally blown flap (EBF), involving direct jet impingement on the aircraft flaps, and the upper surface blown (USB), where the jet flow is attached on the upper surface of the wing and directed downwards. Towards the goal of developing scaling laws to predict unsteady loads imposed on the structural components of these STOL aircraft from small model tests, the near field fluctuating pressure behavior for the simplified cases of a round free cold jet and the same jet impinging on a flat plate was investigated. Examples are given of coherences, phase lags (giving convection velocities), and overall fluctuating pressure levels measured. The fluctuating pressure levels measured on the flat plate are compared to surface fluctuating pressure levels measured on full-scale powered-lift configuration models.

Schroeder, J. C.↗