Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Experimental Verification of Boundary-Layer Corrections in Hypersonic Nozzles

The problem of accurately predicting boundary-layer growth for supersonic nozzle design assumes increased importance as the design Mach Number of the nozzles is pushed into the hypersonic regime. Several methods of calculating this growth have been advanced which vary in ease of computation and accuracy of results. Results of the calibrations performed on two hypersonic helium nozzles recently put into operation in the 11-in. Hypersonic Tunnel Section at the NASA Langley Research Center indicate that the method employed for boundary-layer calculations in these nozzles is adequate. The flow in the test region of both nozzles has been found to be of good quality and the Mach Numbers obtained agree very satisfactorily with the desired design Mach Number.

Boundary Layer Equations↗
NASA NTRS1959

An Experimental Investigation of a Triangular Wing of Aspect Ratio 2 and a Body Warped to be Trimmed at M = 2.24

A cambered and twisted triangular wing of aspect ratio 2 in combination with a cambered body was investigated experimentally to determine the effectiveness of the camber in reducing the drag due to lift at trim at supersonic speeds. Four arrangements were tested comprising all combinations of a symmetrical and a cambered wing with a symmetrical and a cambered body. The camber shape investigated was derived by linearized lifting surface theory for triangular wings with sonic leading edges and satisfied the requirement that the wing be trimmed at the design Mach number and lift coefficient. The experimental results for the cambered wing and cambered body showed that the drag coefficient at trim was always greater, at the same lift coefficient, than that for the untrimmed symmetrical wing and body. The trim lift coefficient was positive and decreased with increasing Mach number. At the design Mach number of 2.24, the trim lift coefficient was somewhat lower and the drag coefficient was higher than values predicted by linearized lifting surface theory for the wing alone. A comparison of the trim lift-drag ratio of the cambered wing and cambered body with values obtained by trimming the symmetrical wing and symmetrical body either with a canard or a trailing-edge flap showed that, at approximately the design Mach number the cambered configuration developed a somewhat higher value than the trailing-edge flap configuration but a lower value than the canard configuration.

Adams, Gaynor J.↗
NASA NTRS1959

Lift and Drag of a Swept-Wing Fighter Airplane at Transonic and Supersonic Speeds

A flight investigation was made of the lift and drag of a sweptwing fighter airplane in the basic configuration and in a slats-locked-closed configuration over a Mach number range from about 0.63 to about 1.44. At a nominal lift coefficient of 0.1 negligible drag-coefficient difference existed between the two configurations over a comparable Mach number and altitude range. For the basic configuration at zero lift the supersonic drag level was about three times as great as the subsonic drag level, which was about 0.01, whereas the drag-due-to-lift factor increased about 137 percent over the test Mach number range. At comparable Mach numbers the high-altitude data produced a larger lift-curve slope and showed a more pronounced variation of lift-curve slope in the transonic region than did the low-altitude data. For the high-altitude data the lift-curve slope at a Mach number of 1.44 was approximately 62 percent of the value at a Mach number of 0.9.

SWEPT WING↗
NASA NTRS1955

Preliminary Results of an Investigation at Transonic Speeds to Determine the Effects of a Heated Propulsive Jet on the Drag Characteristics of a Related Series of Afterbodies

Preliminary results are presented from an investigation to determine the influence of afterbody geometry on the effects of a sonic propulsive jet at transonic speeds. The results presented are base pressure coefficient and afterbody pressure-drag coefficient as a function of jet pressure ratio for different values of Mach number and jet temperature. Geometric parameters investigated include boattail angle, jet-to-model diameter ratio, and jet-to-base diameter ratio.

Henry, Beverly Z , Jr↗
NASA NTRS1996

Aerothermodynamic Analysis of Commercial Experiment Transporter (COMET) Reentry Capsule

An aerothermodynamic analysis of the Commercial Experiment Transporter (COMET) reentry capsule has been performed using the laminar thin-layer Navier-Stokes solver Langley Aerothermodynamic Upwind Relaxation Algorithm. Flowfield solutions were obtained at Mach numbers 1.5, 2, 5, 10, 15, 20, 25, and 27.5. Axisymmetric and 5, 10, and 20 degree angles of attack were considered across the Mach-number range, with the Mach 25 conditions taken to 90 degrees angle of attack and the Mach 27.5 cases taken to 60 degrees angle of attack. Detailed surface heat-transfer rates were computed at Mach 20 and 25, revealing that heating rates on the heat-shield shoulder ,can exceed the stagnation-point heating by 230 percent. Finite-rate chemistry solutions were performed above Mach 10, otherwise perfect gas computations were made. Drag, lift, and pitching moment coefficients are computed and details of a wake flow are presented. The effect of including the wake in the solution domain was investigated and base pressure corrections to forebody drag coefficients were numerically determined for the lower Mach numbers. Pitching moment comparisons are made with direct simulation Monte Carlo results in the more rarefied flow at the highest Mach numbers, showing agreement within two-percent. Thin-layer Navier-Stokes computations of the axial force are found to be 15 percent higher across the speed range than the empirical/Newtonian based results used during the initial trajectory analyses.

Wood, William A.↗
NASA NTRS1947

Lift and Drag of Wings with Small Span

The lift coefficient of!a wing of small span at first shows a linear increase for the increasing angle of attack, but to a lesser degree then was to be expected according to the theory of the lifting line; thereafter the lift coefficient increases more rapidly than linearity, as contrasted with the the theory of the lifting line. The induced drag coefficient for a given lift coefficient, on the other hand, is obviously much smaller than it would be according to the theory. A mall change in the theory of the lifting line will cover these deviations.

Weinig, F.↗
NASA NTRS1948

Aerodynamic Characteristics at Subsonic and Supersonic Mach Numbers of a Thin Triangular Wing of Aspect Ratio 2 II : Maximum Thickness at Midchord

The lift, drag, and pitching-moment characteristics of a triangular wing, having an aspect ratio of 2 and a symmetrical double-wedge profile of 5-percent-chord maximum thickness at midchord, have been evaluated from wind-tunnel tests at Mach numbers from 0.50 to 0.975 and from 1.09 to 1.49 and at Reynolds numbers ranging from 0.67 to 0.85 million. The lift, drag, and pitching-moment coefficients of the triangular wing with a leading-edge sweepback of approximately 63 degrees did not exhibit the irregular variations with Mach number at high subsonic and low supersonic Mach numbers that are characteristic of unswept wings. The lift-curve slope increased steadily with Mach number below unity and declined slowly beyond the Mach number of 1.13. A substantial rise in the minimum drag coefficient occurred between Mach numbers of 0.95 and 1.20 with an associated reduction in the maximum lift-drag ratio. The aerodynamic center shifted rearward toward the centroid of area of the wing with increasing Mach number below 0.975; whereas above 1.09 it coincided with the centroid.

Walker, Harold J↗
NASA NTRS1994

A comparison of turbulence models in computing multi-element airfoil flows

Four different turbulence models are used to compute the flow over a three-element airfoil configuration. These models are the one-equation Baldwin-Barth model, the one-equation Spalart-Allmaras model, a two-equation k-omega model, and a new one-equation Durbin-Mansour model. The flow is computed using the INS2D two-dimensional incompressible Navier-Stokes solver. An overset Chimera grid approach is utilized. Grid resolution tests are presented, and manual solution-adaptation of the grid was performed. The performance of each of the models is evaluated for test cases involving different angles-of-attack, Reynolds numbers, and flap riggings. The resulting surface pressure coefficients, skin friction, velocity profiles, and lift, drag, and moment coefficients are compared with experimental data. The models produce very similar results in most cases. Excellent agreement between computational and experimental surface pressures was observed, but only moderately good agreement was seen in the velocity profile data. In general, the difference between the predictions of the different models was less than the difference between the computational and experimental data.

Rogers, Stuart E.↗
NASA NTRS1953

Rocket-Model Investigation of the Longitudinal Stability, Drag, and Duct Performance Characteristics of the North American MX-770 (X-10) Missile at Mach Numbers from 0.80 to 1.70

A free-flight 0.12-scale rocket-boosted model of the North American MX-770 (X-10) missile has been tested in flight by the Pilotless Aircraft Research Division of the Langley Aeronautical Laboratory. Drag, longitudinal stability, and duct performance data were obtained at Mach numbers from 0.8 to 1.7 covering a Reynolds number range of about 9 x 10(exp 6) to 24 x 10(exp 6) based on wing mean aerodynamic chord. The lift-curve slope, static stability, and damping-in-pitch derivatives showed similar variations with Mach number, the parameters increasing from subsonic values in the transonic region and decreasing in the supersonic region. The variations were for the most part fairly smooth. The aerodynamic center of the configuration shifted rearward in the transonic region and moved forward gradually in the supersonic region. The pitching effectiveness of the canard control surfaces was maintained throughout the flight speed range, the supersonic values being somewhat greater than the subsonic. Trim values of angle of attack and lift coefficient changed abruptly in the transonic region, the change being associated with variations in the out-of-trim pitching moment, control effectiveness, and aerodynamic-center travel in this speed range. Duct total-pressure recovery decreased with increase in free-stream Mach number and the values were somewhat less than normal-shock recovery. Minimum drag data indicated a supersonic drag coefficient about twice the subsonic drag coefficient and a drag-rise Mach number of approximately 0.90. Base drag was small subsonically but was about 25 percent of the minimum drag of the configuration supersonically.

Bond, Aleck C.↗
NASA NTRS1994

Dynamic ground effects flight test of an F-15 aircraft

Flight tests to determine the changes in the aerodynamic characteristics of an F-15 aircraft caused by dynamic ground effects are described. Data were obtained for low and high sink rates between 0.7 and 6.5 ft/sec and at two landing approach speeds and flap settings: 150 kn with the flaps down and 170 kn with the flaps up. Simple correlation curves are given for the change in aerodynamic coefficients because of ground effects as a function of sink rate. Ground effects generally caused an increase in the lift, drag, and nose-down pitching movement coefficients. The change in the lift coefficient increased from approximately 0.05 at the high-sink rate to approximately 0.10 at the low-sink rate. The change in the drag coefficient increased from approximately 0 to 0.03 over this decreasing sink rate range. No significant difference because of the approach configuration was evident for lift and drag; however, a significant difference in pitching movement was observed for the two approach speeds and flap settings. For the 170 kn with the flaps up configuration, the change in the nose-down pitching movement increased from approximately -0.008 to -0.016. For the 150 kn with the flaps down configuration, the change was approximately -0.008 to -0.038.

Corda, Stephen↗
NASA NTRS1989

Analysis of an unswept propfan blade with a semiempirical dynamic stall model

The time history response of a propfan wind tunnel model with dynamic stall is studied analytically. The response obtained from the analysis is compared with available experimental data. The governing equations of motion are formulated in terms of blade normal modes which are calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag and moment coefficients for angles of attack below the static stall angle are obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to angle of attack is used to obtain lift, drag and moment coefficients. Using these coefficients, the aerodynamic forces are calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory is used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near the setting angle.

Reddy, T. S. R.↗
NASA NTRS1976

Comparison of aerodynamic theory and experiment for jet-flap wings

Aerodynamic theory predictions made for a jet flapped wing were compared with experimental data obtained in a fairly extensive series of tests in the Langley V/STOL tunnel. The tests were made on a straight, rectangular wing and investigated two types of jet flap concepts: a pure jet flap with high jet deflection and a wing with blowing at the knee of a plain trailing edge flap. The tests investigated full and partial span blowing for wing aspect ratios of 8.0 and 5.5 and momentum coefficients from 0 to about 4. The total lift, drag, and pitching moment coefficients predicted by the theory were in excellent agreement with experimental values for the pure jet flap, even with the high jet deflection. The pressure coefficients on the wing, and hence the circulation lift coefficients, were underpredicted, however, because of the linearizing assumptions of the planar theory. The lift, drag, and pitching moment coefficients, as well as pressure coefficients, were underpredicted for the wing with blowing over the flap because of the failure of the theory to account for the interaction effect of the high velocity jet passing over the flap.

Gainer, T. G.↗
NASA NTRS1985

Detailed measurements of the flowfield in the vicinity of an airfoil with glaze ice

An experimental study has been conducted in the OSU subsonic tunnel to measure the characteristics of the separation bubble on an airfoil with glaze ice. A measured glaze ice accretion on a NACA 0012 airfoil was simulated in wood for this dry tunnel test. The 21 inch chord model was pressure belted and the ice shape internally tapped to obtain surface pressures, lift and moment coefficients. A wake survey probe was used to obtain airfoil drag. The separation bubble was explored by measuring the time averaged velocities using a split film probe. The probe was positioned using a computer controlled two-dimensional traversing system. In this paper, airfoil lift, drag, and moment coefficient data are compared for the airfoil with and without glaze ice. Velocity profiles in the separation bubble are presented for several chordwise stations at three angles of attack. The ice shape caused a severe lift and drag penalty. The velocity profiles show clearly the large bubble geometry, regions of reversed flow, and bubble reattachment.

Bragg, M. B.↗
NASA NTRS1989

Aeroelastic analysis of prop fan blades with a semiempirical dynamic stall model

The time-history response of a propfan wind-tunnel model with dynamic stall was studied analytically. The response obtained from the analysis was compared with available experimental data. The governing equations of motion were formulated in terms of blade normal modes calculated using the COSMIC-NASTRAN computer code. The response analysis considered the blade plunging and pitching motions. The lift, drag, and moment coefficients for angles of attack below the static stall angle were obtained from a quasi-steady theory. For angles above static stall angles, a semiempirical dynamic stall model based on a correction to the angle of attack was used to obtain lift, drag, and moment coefficients. Using these coefficients, the aerodynamic forces were calculated at a selected number of strips, and integrated to obtain the total generalized forces. The combined momentum-blade element theory was used to calculate the induced velocity. The semiempirical stall model predicted a limit cycle oscillation near the setting angle at which large vibratory stresses were observed in an experiment. The predicted mode and frequency of oscillation also agreed with those measured in the experiment near this setting angle. The results also correlated well with the other published data that used a semiempirical dynamic stall model based on a synthesized procedure.

Reddy, T. S. R.↗
NASA NTRS1941

The Effect of Various Wing-Gun Installations on the Aerodynamic Characteristics of an Airplane Model Equipped with an NACA Low-Drag Wing, Special Report

An investigation was made in the NACA 19-foot pressure wind tunnel to determine the effect of various win-gun installation on the aerodynamic characteristics of a model with an NACA low-drag wing. Measurements were made of lift and drag over an angle-of-attack range and for several values of dynamic pressure on a four-tenths scale model of a high-speed airplane equipped with the low-drag wing and with various wing-gun installations. Two installations were tested: one in which the blast tube and part of the gun barrel protrude ahead of the wing and another in which the guns is mounted wholly within the wing. Two types of openings for the latter installation were tested. For each installation three simulated guns were mounted in each wing. The results are given in the form of nondimensional coefficients. The installations tested appear to have little effect on the maximum-lift coefficient of the model. However, the drag coefficient shows a definite change. The least adverse effect was obtained with the completely internal mounting and small nose entrance. The results indicate that a properly designed wing-gun installation will have very little adverse effect on the aerodynamic characteristics of the low-drag wing.

Muse, Thomas C.↗
NASA NTRS1973

Experimental investigation of the cornering of a C40 x 14-21 cantilever aircraft tire

An experimental investigation was conducted at the Langley aircraft landing loads and traction facility to define the cornering characteristics of a size C40 x14-21 aircraft tire of cantilever design. These characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained for the tire operating on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 20 deg and at ground speeds of 5 to 100 knots, both with and without braking. The results of this investigation show that the cornering-force and drag-force friction coefficients and self-alining torque were influenced by the yaw angle, ground speed, brake torque, surface wetness, and the locked-wheel condition.

Dreher, R. C.↗
NASA NTRS1987

Wind-tunnel test results of airfoil modifications for the EA-6B

Wind-tunnel tests have been conducted (to determine the effects on airfoil performance for several airfoil modifications) for the EA-6B Wing Improvement Program. The modifications consist of contour changes to the leading-edge slat and trailing-edge flap to provide a higher low-speed maximum lift with no high-speed cruise-drag penalty. Airfoil sections from the 28- and 76-percent span stations were selected as baseline shapes with the major testing devoted to the inboard airfoil section (28-percent span station). The airfoil modifications increased the low-speed maximum lift coefficient between 20 and 35 percent over test conditions of 3 to 14 million chord Reynolds number and 0.14 to 0.34 Mach number. At the high-speed test conditions of 0.4 to 0.80 Mach number and 10 million chord Reynolds number, the modified airfoils had either matched or had lower drag coefficients for all normal-force coefficients above 0.2 as compared to the baseline airfoil. At normal-force coefficients less than 0.2, the baseline (original) airfoil had lower drag coefficients than any of the modified airfoils.

Sewall, W. G.↗
NASA NTRS1957

Effects of Inlet Modification and Rocket-Rack Extension on the Longitudinal Trim and Low-Lift Drag of the Douglas F5D-1 Airplane as Obtained with a 0.125-Scale Rocket-Boosted Model between Mach Numbers of 0.81 and 1.64, TED No. NACA AD 399

A flight investigation was conducted to determine the effects of an inlet modification and rocket-rack extension on the longitudinal trim and low-lift drag of the Douglas F5D-1 airplane. The investigation was conducted with a 0.125-scale rocket-boosted model which was flight tested at the Langley Pilotless Aircraft Research Station at Wallops Island, Va. Results indicate that the combined effects of the modified inlet and fully extended rocket racks on the trim lift coefficient and trim angle of attack were small between Mach numbers of 0.94 and 1.57. Between Mach numbers of 1.10 and 1.57 there was an average increase in drag coefficient of about o,005 for the model with modified inlet and extended rocket racks. The change in drag coefficient due to the inlet modification alone is small between Mach numbers of 1.59 and 1.64

Hastings, Earl C., Jr.↗