Results for “Creep modeling” — Page 46

NASA NTRS1981

A multilayer model of time dependent deformation following an earthquake on a strike-slip fault

A multilayer model of the Earth to calculate finite element of time dependent deformation and stress following an earthquake on a strike slip fault is discussed. The model involves shear properties of an elastic upper lithosphere, a standard viscoelastic linear solid lower lithosphere, a Maxwell viscoelastic asthenosphere and an elastic mesosphere. Systematic variations of fault and layer depths and comparisons with simpler elastic lithosphere over viscoelastic asthenosphere calculations are analyzed. Both the creep of the lower lithosphere and astenosphere contribute to the postseismic deformation. The magnitude of the deformation is enhanced by a short distance between the bottom of the fault (slip zone) and the top of the creep region but is less sensitive to the thickness of the creeping layer. Postseismic restressing is increased as the lower lithosphere becomes more viscoelastic, but the tendency for the width of the restressed zone to growth with time is retarded.

Cohen, S. C.↗

NASA NTRS1993

Aerospace devices for magnetic replicas

Retained persistent magnetic field has been studied and improved in the superconductor YBa2Cu3O7 (Y123). During the study, trapped magnetic field, B(t), has been increased by over a factor of 10(exp 5). Methods used to improve magnetic field trapping were principally: (1) the adoption of the Melt Texturing process to increase grain size; (2) the addition of excess Y to disperse deposits of Y2BaCuO5 (Y211) and again increase grain size; (3) irradiation with high energy particles including 1H+, 3He++, 4He++, and fission fragments; and (4) utilizing temperatures below 77 K has also been quantified as a way to increase trapped field. In addition, in our study of B(t), we have found laws governing creep, activation, temperature dependence, creep vs. current flow, etc. In the range 20 K less than or equal to T less than or equal to 65 K, and for B less than 10 Tesla, a simple empirical relationship was found: B(trap) (T2) = B(trap) (T1) ((Tc - T2)/(Tc - T1))squared where Tc is the critical temperature. The highest experimental trapped field was B(trap) = 3.96 Tesla, at 65 K. We believe this to be the highest persistent field ever produced, by any method. A two component model of the persistent currents has been developed. This accurately reproduces the data, using as parameters only the magnitude of a constant surface current, J(s), and a constant volume current J(v). The model successfully predicts B(t) (xyz) for the case of maximum trapped field, for all samples observed. It has also been extended to describe the unsaturated case either zero field cooled, or field cooled. Loss of strap with time has been studied for the critical state (Bt,max), and non critical state (Bt less than Bt,max), for times from a few minutes to a few months, for unirradiated material, for irradiation by 1H+, 3He++, 4He++, high z projectiles, and neutrons, and for all materials used in the overall study. We conclude that: (1) multi Tesla trapped fields are attained; (2) fields over 10 T are achievable; (3) creep is not a large problem; (4) application is feasible to motors, generators, magnets for particle beam optics, separators, levitating bearings, energy storage, shielding, and transportation.

Weinstein, Roy↗

DOE OSTI2024

Fuel performance analysis of Cr-coated Zircaloy-4 cladding during a prototypical LOCA event using BISON

Here, deformation and failure of chromium (Cr) coated Zircaloy-4 (Zry-4) were studied in loss-of-coolant accident (LOCA) conditions using the BISON fuel performance code. The BISON validation model simulating Halden research reactor experiments was extended to include Cr coatings and higher rod internal pressures to simulate high-burnup fuel. The transient simulations show Cr coatings help relieve stress in the Zry-4 substrate during the transient, delaying the onset of high-temperature creep, which leads to ballooning and bursting of the cladding. A nominal Cr coating thickness of 30 µm delays clad failure by 26 seconds and increases the clad burst temperature by 40 K. A parametric study showed that time to failure and burst temperature both increase with coating thickness, and Cr-coated cladding offers burst resistance under a wide range of rod internal pressures simulating high-burnup fuel. Results indicate that a thin Cr coating provides resistance against ballooning and bursting of cladding during LOCA events.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Estimating viscoelastic compliance of desiccating cementitious materials using drying prism tests

Highlights: • Determining relative humidity and degree of reaction of desiccating cementitious materials via an integrated method • Extracting moisture diffusion coefficient of cement mortar using the mass loss data of the prism specimens • Estimating uniaxial viscoelastic compliance of cement mortar using the shrinkage strain data of the prism specimens An integrated modeling approach to determining internal relative humidity and degree of reaction of desiccating cementitious materials has been developed. By simultaneously accounting for both self-desiccation and external drying, the model is capable of predicting the evolution of material properties of desiccating cementitious materials. Using the mass loss data of the prism specimens, the moisture diffusion coefficient of a nonlinear model for cement mortar was determined. Additionally, a previous poroviscoelastic shrinkage model was modified and extended. Through comparison of predicted and measured axial strain of the prism specimens, the viscoelastic compliance of cement mortar was extracted. The present work revealed that it is possible to use a simple drying prism test to fit the moisture diffusion coefficient and creep compliance of cementitious materials, though the comparison of the extracted viscoelastic compliance with measured compliance was only reasonable if the outer layer of the drying mortar was presumed to have microcracking.

36 MATERIALS SCIENCE↗

NASA NTRS2014

Damage Characterization of EBC-SiCSiC Ceramic Matrix Composites Under Imposed Thermal Gradient Testing

Due to their high temperature capabilities, Ceramic Matrix Composite (CMC) components are being developed for use in hot-section aerospace engine applications. Harsh engine environments have led to the development of Environmental Barrier Coatings (EBCs) for silicon-based CMCs to further increase thermal and environmental capabilities. This study aims at understanding the damage mechanisms associated with these materials under simulated operating conditions. A high heat-flux laser testing rig capable of imposing large through-thickness thermal gradients by means of controlled laser beam heating and back-side air cooling is used. Tests are performed on uncoated composites, as well as CMC substrates that have been coated with state-of-the-art ceramic EBC systems. Results show that the use of the EBCs may help increase temperature capability and creep resistance by reducing the effects of stressed oxidation and environmental degradation. Also, the ability of electrical resistance (ER) and acoustic emission (AE) measurements to monitor material condition and damage state during high temperature testing is shown; suggesting their usefulness as a valuable health monitoring technique. Micromechanics models are used to describe the localized stress state of the composite system, which is utilized along with ER modeling concepts to develop an electromechanical model capable of characterizing material behavior.

protective coatings (nonmetallic)↗

NASA NTRS2024

Extreme Temperature Additively Manufactured GRX-810 Alloy Development and Hot-fire Testing for Liquid Rocket Engines

Additive manufacturing (AM) has revolutionized component design for liquid rocket engines by offering rapid manufacturing capabilities. This has led to significant opportunities for development and flight programs in the propulsion industry, resulting in cost and schedule savings, as well as performance improvements through new designs and alloy development. A noteworthy example is the GRX-810 oxide dispersion strengthened (ODS) alloy, which was specifically developed for extreme temperatures. This Ni-Co-Cr based alloy was created using integrated computational materials engineering (ICME) techniques to focus on a new class of materials with exceptional temperature and oxidation-resistant properties. The GRX-810 alloy utilizes AM processes to incorporate nano-scale yttria particles throughout its microstructure, resulting in remarkable enhancements. Compared to traditional Nickel-based superalloys, the GRX-810 alloy offers a two-fold increase in tensile strength, 1,000-fold better creep properties, and two-fold improvement in oxidation resistance. NASA successfully demonstrated the development and manufacturing of components using the GRX-810 alloy through laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Extensive efforts were made to model, evaluate metallurgical properties, develop heat treatment processes, characterize the microstructure, and determine mechanical properties. The GRX-810 alloy was specifically designed for aerospace applications, including liquid rocket engine injectors, preburners, turbines, and hot-section components, capable of withstanding temperatures up to 1,100 °C. The objective of this alloy development is to bridge the temperature gap between traditional Nickel-based superalloys and refractory alloys. This paper provides a comprehensive comparison of the GRX-810 alloy with other aerospace alloys, discussing its microstructure, mechanical properties, processing advancements, component development, and hot-fire testing results. The ultimate goal of this development was to elevate the Technology Readiness Level (TRL) of the GRX-810 alloy, enabling its integration into NASA and commercial aerospace applications.

GRX-810↗

NASA NTRS2024

Extreme Temperature Additively Manufactured GRX-810 Alloy Development and Hot-fire Testing for Liquid Rocket Engines

Additive manufacturing (AM) has revolutionized component design for liquid rocket engines by offering rapid manufacturing capabilities. This has led to significant opportunities for development and flight programs in the propulsion industry, resulting in cost and schedule savings, as well as performance improvements through new designs and alloy development. A noteworthy example is the GRX-810 oxide dispersion strengthened (ODS) alloy, which was specifically developed for extreme temperatures. This Ni-Co-Cr based alloy was created using integrated computational materials engineering (ICME) techniques to focus on a new class of materials with exceptional temperature and oxidation-resistant properties. The GRX-810 alloy utilizes AM processes to incorporate nano-scale yttria particles throughout its microstructure, resulting in remarkable enhancements. Compared to traditional Nickel-based superalloys, the GRX-810 alloy offers a two-fold increase in tensile strength, 1,000-fold better creep properties, and two-fold improvement in oxidation resistance. NASA successfully demonstrated the development and manufacturing of components using the GRX-810 alloy through laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Extensive efforts were made to model, evaluate metallurgical properties, develop heat treatment processes, characterize the microstructure, and determine mechanical properties. The GRX-810 alloy was specifically designed for aerospace applications, including liquid rocket engine injectors, preburners, turbines, and hot-section components, capable of withstanding temperatures up to 1,100 °C. The objective of this alloy development is to bridge the temperature gap between traditional Nickel-based superalloys and refractory alloys. This paper provides a comprehensive comparison of the GRX-810 alloy with other aerospace alloys, discussing its microstructure, mechanical properties, processing advancements, component development, and hot-fire testing results. The ultimate goal of this development was to elevate the Technology Readiness Level (TRL) of the GRX-810 alloy, enabling its integration into NASA and commercial aerospace applications.

GRX-810↗

DOE OSTI2021

A Time-Dependent Directional Damage Theory for Brittle Rocks Considering the Kinetics of Microcrack Growth

In this work, a novel microcrack damage theory for describing the time-dependent behavior of brittle rocks is proposed. Instead of using scalar or tensorial variables to approximate the effect of microcracks, the concept of directional damage is introduced by upscaling the directional distribution density of microcracks through the noninteracting homogenization scheme. The contribution of an individual crack on global strain is first derived from the crack-opening displacements including sliding, closure, and dilation. The model is then cast in the free energy form, and the range of parameters ensuring compliance with the second law of thermodynamics is derived rigorously. Considering that the subcritical propagation of microcracks is the dominant mechanism behind the time-dependent deformation and failure of brittle rocks, the driving force for directional damage is defined as the corresponding energy release rate, and the effect of time is introduced through a damage evolution law inspired from the kinetics of subcritical crack growth. The model is applied to simulate the behavior of basalt rock under various loading conditions. In addition to predicting the stress–strain–time response, the model offers enhanced resolution in representing the anisotropic characteristics of microcrack-induced damage in brittle rocks and their time-dependent evolutions.

58 GEOSCIENCES↗

NASA NTRS1973

Theoretical analysis of swelling characteristics of cylindrical uranium dioxide fuel pins with a niobium - 1-percent-zirconium clad

The relations between clad creep strain and fuel volume swelling are shown for cylindrical UO2 fuel pins with a Nb-1Zr clad. These relations were obtained by using the computer code CYGRO-2. These clad-strain - fuel-volume-swelling relations may be used with any fuel-volume-swelling model, provided the fuel volume swelling is isotropic and independent of the clad restraints. The effects of clad temperature (over a range from 118 to 1642 K (2010 to 2960 R)), pin diameter, clad thickness and central hole size in the fuel have been investigated. In all calculations the irradiation time was 500 hours. The burnup rate was varied.

Saltsman, J. F.↗

NASA NTRS1983

HOST structural analysis program overview

Hot section components of aircraft gas turbine engines are subjected to severe thermal structural loading conditions, especially during the start up and take off portions of the engine cycle. The most severe and damaging stresses and strains are those induced by the steep thermal gradients induced during the start up transient. These transient stresses and strains are also the most difficult to predict, in part because of the temperature gradients and distributions are not well known or readily predictable, and also because the cyclic elastic viscoplastic behavior of the materials at these extremes of temperature and strain are not well known or readily predictable. A broad spectrum of structures related technology programs is underway to address these deficiencies. One element of the structures program is developing improved time varying thermal mechanical load models for the entire engine mission cycle from start up to shutdown. Another major part of the program is the development of new and improved nonlinear 3-D finite elements and associated structural analysis programs, including the development of temporal elements with time dependent properties to account for creep effects in the materials and components.

Johns, R. H.↗

NASA NTRS1989

High temperature inelastic deformation under uniaxial loading - Theory and experiment

The elevated-temperature uniaxial inelastic deformation behavior of an Ni-base alloy, B1900 + Hf, is investigated by performing isothermal tensile, creep, cyclic, stress relaxation, and thermomechanical fatigue tests. The range of strain rates examined is from 10 to the -7th to 100 per sec, while the test temperatures range from 25 to 1093 C. This extensive constitutive data base has been used for evaluating the unified constitutive models of Bodner and Partom (1972) and of Walker (1972) which apply for the small-strain regime. Comparison of test results with independent model predictions indicates good agreement over a broad range of loading conditions, demonstrating the applicability of the unified-constitutive-equation approach for describing the strongly nonlinear and temperature-dependent response of meals under a wide range of deformation and thermal histories. Thus the results give confidence that the unified approach is an effective and efficient approach in which complex history-dependent thermoviscoplastic flow can be represented within a single inelastic strain-rate term.

Chan, K. S.↗

DOE OSTI2020

Understanding the deformation mechanisms in Ni-based superalloys with using crystal plasticity finite element method

Nl-based superalloy is considered as a good candidate due to its excellent resistance to elevated temperature deformation for long term period application. Understanding the deformation and failure mechanisms of Ni-Based superalloys is very helpful for providing design guidelines for processing Ni-based superalloys. Experimental characterization indicates that the deformation mechanisms of Ni based superalloy is strongly microstructure dependent. Besides, damage transform from the void nucleation to the macro cracks by voids growth leading to the failure of the Ni-based superalloys are also showing strong microstructure sensitivity. Therefore, this work focuses on the prediction and comprehension of the deformation and void growth behavior in Ni based superalloy at different working conditions via crystal plasticity finite element modeling and simulation. Physically based crystal plasticity frameworks were developed for newly Ni- based superalloy Haynes 282. It was found that dislocation shearing through the precipitates were acting as the main contributor to the strength of Haynes 282 at room temperature and 815°C. Our analysis of the creeping behavior of Haynes 282 exhibited that resistance of general climb replaced by the resistance induced by the deposited climb dislocation density. In addition, in the study of void growth behavior, our simulation results demonstrated that as the main loading axis perpendicular to the grain boundary (GB), voids grow more slowly on tilt GBs in bicrystals than those in single and bicrystals with twist GBs. And tilt GBs would promote the void grow into irregular shape.

36 MATERIALS SCIENCE↗

DOE OSTI2021

As-Run Thermal Analysis for the AGC-4 Experiment Irradiated in the ATR

The Advanced Graphite Capsule (AGC) irradiation experiment will provide irradiation creep rate data for the new graphite proposed for the Next Generation Nuclear Plant (NGNP) program. The fourth experiment in the series (AGC-4) was designed to irradiate various types of graphite specimens at a temperature of 900 ºC and targeted displacements per atom (DPA) of 6. This experiment has been irradiated in the east flux trap of the Advanced Test Reactor (ATR) during the cycles of 157D, 158A, 162A, 162B, 164A, 164B, 166A, and 166B. Temperatures were monitored using twelve thermocouples (TC) located at various elevations in the reactor core, and variable helium-argon gas mixtures were used for gas gap temperature control of the specimens. The purpose of this Engineering Calculation and Analysis Report (ECAR) is to calculate the specimen temperature after the model is calibrated by the measured TC data with the as-run heating rates of the components, DPA of the graphite, and the gas mixture compositions during the experiment. As-run specimen mean temperature and the tolerance will be obtained.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1976

Mantle plumes - A boundary layer approach for Newtonian and non-Newtonian temperature-dependent rheologies

Stress is placed on the temperature dependence of both a linear Newtonian rheology and a nonlinear olivine rheology in accounting for narrow mantle flow structures. The boundary-layer theory developed incorporates an arbitrary temperature-dependent power-law rheology for the medium, in order to facilitate the study of mantle plume dynamics under real conditions. Thermal, kinematic, and dynamic structures of mantle plumes are modelled by a two-dimensional natural-convection boundary layer rising in a fluid with a temperature-dependent power-law relationship between shear stress and strain rate. An analytic similarity solution is arrived at for upwelling adjacent to a vertical isothermal stress-free plane. Newtonian creep as a deformation mechanism, thermal anomalies resulting from chemical heterogeneity, the behavior of plumes in non-Newtonian (olivine) mantles, and differences in the dynamics of wet and dry olivine are discussed.

Yuen, D. A.↗

NASA NTRS1996

Structures Division 1994 Annual Report

The NASA Lewis Research Center Structures Division is an international leader and pioneer in developing new structural analysis, life prediction, and failure analysis related to rotating machinery and more specifically to hot section components in air-breathing aircraft engines and spacecraft propulsion systems. The research consists of both deterministic and probabilistic methodology. Studies include, but are not limited to, high-cycle and low-cycle fatigue as well as material creep. Studies of structural failure are at both the micro- and macrolevels. Nondestructive evaluation methods related to structural reliability are developed, applied, and evaluated. Materials from which structural components are made, studied, and tested are monolithics and metal-matrix, polymer-matrix, and ceramic-matrix composites. Aeroelastic models are developed and used to determine the cyclic loading and life of fan and turbine blades. Life models are developed and tested for bearings, seals, and other mechanical components, such as magnetic suspensions. Results of these studies are published in NASA technical papers and reference publication as well as in technical society journal articles. The results of the work of the Structures Division and the bibliography of its publications for calendar year 1994 are presented.

Source record↗

NASA NTRS1997

Structures Division

The NASA Lewis Research Center Structures Division is an international leader and pioneer in developing new structural analysis, life prediction, and failure analysis related to rotating machinery and more specifically to hot section components in air-breathing aircraft engines and spacecraft propulsion systems. The research consists of both deterministic and probabilistic methodology. Studies include, but are not limited to, high-cycle and low-cycle fatigue as well as material creep. Studies of structural failure are at both the micro- and macrolevels. Nondestructive evaluation methods related to structural reliability are developed, applied, and evaluated. Materials from which structural components are made, studied, and tested are monolithics and metal-matrix, polymer-matrix, and ceramic-matrix composites. Aeroelastic models are developed and used to determine the cyclic loading and life of fan and turbine blades. Life models are developed and tested for bearings, seals, and other mechanical components, such as magnetic suspensions. Results of these studies are published in NASA technical papers and reference publication as well as in technical society journal articles. The results of the work of the Structures Division and the bibliography of its publications for calendar year 1995 are presented.

Source record↗

NASA NTRS2004

Advanced Technology Development for Stirling Convertors

A high-efficiency Stirling Radioisotope Generator (SRG) for use on potential NASA Space Science missions is being developed by the Department of Energy, Lockheed Martin, Stirling Technology Company, and NASA Glenn Research Center (GRC). These missions may include providing spacecraft onboard electric power for deep space missions or power for unmanned Mars rovers. GRC is also developing advanced technology for Stirling convertors, aimed at substantially improving the specific power and efficiency of the convertor and the overall power system. Performance and mass improvement goals have been established for second- and thirdgeneration Stirling radioisotope power systems. Multiple efforts are underway to achieve these goals, both in-house at GRC and under various grants and contracts. The status and results to date for these efforts will be discussed in this paper. Cleveland State University (CSU) is developing a multi-dimensional Stirling computational fluid dynamics code, capable of modeling complete convertors. A 2-D version of the code is now operational, and validation efforts at both CSU and the University of Minnesota are complementing the code development. A screening of advanced superalloy, refractory metal alloy, and ceramic materials has been completed, and materials have been selected for creep and joining characterization as part of developing a high-temperature heater head. A breadboard characterization is underway for an advanced controller using power electronics for active power factor control with a goal of eliminating the heavy tuning capacitors that are typically needed to achieve near unity power factors. Key Stirling developments just initiated under recent NRA (NASA Research Announcement) awards will also be discussed. These include a lightweight convertor to be developed by Sunpower Inc. and an advanced microfabricated regenerator to be done by CSU.

Thieme, Lanny G.↗

DOE OSTI2024

Evaluation of proposed Section III Division 5 Class B rules: Piping example problem

Evaluation of proposed Section III Division 5 Class B rules: Piping example problem to be presented include Z pipe geometry and model problem statement, Z pipe loads and design inputs problem statement, Primary Stress Limit overview, Primary stress limit pseudo yield stress calculation, Primary stress limited factored load procedure, Strain limit evaluation composite load cycle, Strain limit evaluation pseudo yield stress, Strain limit evaluation strain limit criteria and ratcheting check, Creep fatigue damage evaluation overview, Creep fatigue damage evaluation alternating stress calculations, Creep fatigue damage evaluation lower bound stress, Creep fatigue damage evaluation stress relaxation history, Creep fatigue damage evaluation damage fractions, and Recommendations to consider for Z-pipe problem.

42 ENGINEERING↗