SEARCH · Engineering Papers

Results for “Conditional Distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Flight survey of the 757 wing noise field and its effects on laminar boundary layer transition. Volume 2: Data compilation

A flight test program was performed using the Boeing 757 flight research airplane to investigate the effect of noise from wing mounted engines on laminar boundary layer transition. An NLF glove was installed on the right wing panel just outboard of the engine. The extent of laminar flow on the glove was measured as a function of engine power setting for a range of flight conditions. A combination of surface and probe microphones was distributed over the upper and lower wing surfaces to measure sound spectra. The flight test program was completed in June 1985 and the results of preliminary analysis indicate that a maximum of about 29 percent of chord laminar flow was obtained on the upper surface and about 28 percent on the lower surface (at a high sideslip condition). The engine speed was varied from about 2600 (idle) to about 4500 (maximum continuous power) r/min. This produced changes in sound pressure level up to 20 dB on the lower surface. On the upper surface, the noise levels were independent of engine power but sensitive to airplane Mach number. No effect of engine power setting on upper surface transition location was observed, and only a small forward movement of the transition location on the lower surface was observed at the high power settings. Volume 1 of this report contains the program description and data analysis. Volume 2 is a compilation of all of the flight test data.

Source record↗

NASA NTRSDate not supplied

Acoustic Flight Test of the Joby Aviation Advanced Air Mobility Prototype Vehicle

An extensive acoustic flight test was performed on the Joby Aviation pre-production all-electric vertical takeoff and landing prototype. With the design intent of carrying a pilot and four passengers a maximum range of 150 miles, this vehicle utilizes distributed propulsion and vectored thrust via six tilting propellers. As part of the Advanced Air Mobility (AAM) National Campaign, this is the first full-scale AAM aircraft tested by NASA over representative conditions for all phases of a typical mission profile. A 58- channel distributed microphone array was used to acquire acoustic measurements on more than 100 test points (31 unique conditions). The measurements were postprocessed with synchronously sampled vehicle position and state data to form ground noise contours of departures and approaches at various flight path angles and accelerations. Comparing ground areas of 75 dBA isolines, approaches consistently exhibit higher noise levels rela- tive to departures. Directivity maps were generated for constant airspeed level flyovers. Examples comparing the differences in a semi-thrust borne and full wing-borne mode are given, with full wing-borne mode representing the quietest phase of the flight envelope tested. Measurements for hover in and out of ground effect are given and found to have 2 to 5 dB variation over a single run, and more significant variation between back-to-back runs. Finally, initial analysis of acoustic symmetry about the longitudinal vehicle axis and repeatability over several test days are presented.

Acoustics↗

NASA NTRS1981

Heat transfer of phase-change materials in two-dimensional cylindrical coordinates

Two-dimensional phase-change problem is numerically solved in cylindrical coordinates (r and z) by utilizing two Taylor series expansions for the temperature distributions in the neighborhood of the interface location. These two expansions form two polynomials in r and z directions. For the regions sufficiently away from the interface the temperature field equations are numerically solved in the usual way and the results are coupled with the polynomials. The main advantages of this efficient approach include ability to accept arbitrarily time dependent boundary conditions of all types and arbitrarily specified initial temperature distributions. A modified approach using a single Taylor series expansion in two variables is also suggested.

Labdon, M. B.↗

NASA NTRS1987

Convergence properties of modal costs for certain distributed parameter systems

A complete modal cost analysis is presented for the vibration of various kinds of simple continua with different boundary conditions. Explicit formulas for the norm of the response (called the 'cost') are derived for these distributed parameter systems. The convergence theorems developed are useful in the model reduction of the equivalent continuum models of large space structures as well as in the selection of finite-element code for control design.

Hu, A.↗

NASA NTRSDate not supplied

Contrails Measurement and Testing Capabilities in NASA's Particulate Aerosol Laboratory

The NASA Glenn Research Center Particulate Aerosol Laboratory (PAL) is a ground test facility for studying emissions and contrails at upper atmospheric conditions. The facility consists of a small-scale combustor that generates hot combustion gases and soot nanoparticles, which flow through a transition pipe into a jet nozzle, which exhausts into an altitude chamber. Thermodynamic conditions experienced in flight are matched in the altitude chamber, allowing the study of ice particle formation of simulated aircraft engine exhaust plumes. A non-intrusive optical diagnostic technique based on Mie scattering provides ice particle size, number density, and mass density. A suite of commercial extractive particle measurement instruments provides estimates of soot number density, size, and black carbon mass distributions. Measurements are presented for various fuels at chamber conditions covering an altitude range of 20,000 ft (6 km) to 45,000 ft (14 km) altitude and ambient temperatures from -48°C to -68°C. The data presented demonstrate the effect of soot number density, altitude, and fuel-to-air equivalence ratio on the contrail ice particle formation. Ice mass density measurements are compared to values predicted by a thermodynamic plume similarity solution.

Optical Instrumentation↗

NASA NTRS1988

MCT crystal growth

Convection and segregation in directional solidification and crystal growth by the Bridgman-Stockbarger technique are traditionally treated by assuming axisymmetric thermal condition on the ampoule wall. It is, however, difficult to achieve such a condition in an experimental setup. Any deviation from an axisymmetric temperature field on the wall of a vertical ampoule represents a horizontal temperature gradient. The horizontal density gradient that results from thermal expansion in the melt under this condition must lead on earth to some buoyance-driven convection, no matter what the axial (vertical) temperature distribution that is imposed on the melt. The magnitude of such convective flows for conditions representative of the MSFC mercury-cadmium-telluride (MCT) Bridgman setup is studied.

Baird, James K.↗

NASA NTRS2001

Spatial Distribution of Cyanobacteria in Modern Stromatolites

Living stromatolites consist of complex microbial communities with distinct distribution patterns for different microbial groups. The cyanobacterial populations of Highborne Cay Bahamas exemplify this phenomenon. Field observations reveal distinct distribution patterns for several of these cyanobacterial species. To date 10 different cyanobacterial cultures, including both filamentous and endolithic species, have been isolated from these stromatolites. We will present data on the growth and motility characteristics as well as on the nutritional requirements of these isolates. These data will then be correlated with the field observed distributions for these species. Lastly laboratory simulations of stromatolites grown under various conditions of irradiance, flow and cyanobacterial community composition will be presented. These experiments allow us to evaluate our predictions regarding controls on cyanobacterial distribution.

Prufert-Bebout, Lee↗

NASA NTRS1991

A system-approach to the elastohydrodynamic lubrication point-contact problem

The classical EHL (elastohydrodynamic lubrication) point contact problem is solved using a new system-approach, similar to that introduced by Houpert and Hamrock for the line-contact problem. Introducing a body-fitted coordinate system, the troublesome free-boundary is transformed to a fixed domain. The Newton-Raphson method can then be used to determine the pressure distribution and the cavitation boundary subject to the Reynolds boundary condition. This method provides an efficient and rigorous way of solving the EHL point contact problem with the aid of a supercomputer and a promising method to deal with the transient EHL point contact problem. A typical pressure distribution and film thickness profile are presented and the minimum film thicknesses are compared with the solution of Hamrock and Dowson. The details of the cavitation boundaries for various operating parameters are discussed.

Lim, Sang Gyu↗

NASA NTRS1992

A system-approach to the elastohydrodynamic lubrication point-contact problem

Lim, Sang G.↗

NASA NTRS1978

Scale effects on supercritical airfoils

A survey of research relative to scale effects on supercritical airfoils has been conducted. The results of this survey indicated that Reynolds number scale effects have a significant impact on airfoil design and performance. Further, this impact is greater for supercritical airfoils than for conventional airfoils. It was found that low Reynolds number drag data could be extrapolated to high Reynolds number conditions provided the flow was attached and the pressure distribution shape did not change appreciably. Airfoil lift and pitching-moment data obtained at low Reynolds numbers cannot be extrapolated to full-scale values. Viscous theoretical transonic analysis methods currently under development will significantly improve the ability of the designer to account for scale effects. Boundary-layer manipulation in low Reynolds number facilities using natural transition or aft located transition strips to simulate high Reynolds number conditions was shown to be an uncertain test procedure and reliance should be made on high Reynolds number facilities if available.

Blackwell, J. A., Jr.↗

NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part II : Stress and Strength Determination

The tests described in this report furnished data on the actual aerodynamic forces, and the resulting stresses and bending moments in the hull of the U. S. S. "Los Angeles" during as severe still-air maneuvers as the airship would normally be subjected to, and in straight flight during as rough air as is likely to occur in service, short of squall or storm conditions. The maximum stresses were found to be within the limits provided for in accepted practice in airship design. Normal flight in rough air was shown to produce forces and stresses about twice as great as the most severe still-air maneuvers. No light was thrown upon the forces which might occur in extreme or exceptional conditions, such as the storm which destroyed the "Shenandoah". The transverse aerodynamic forces on the hull proper were found to be small and irregular. Owing to the necessity of conserving helium, it was impossible to fly the airship in a condition of large excess of buoyancy or weight in order to determine the air pressure distribution at a fixed angle of pitch. However, there is every reason to believe that in that condition the forces on the actual airship are as close to the wind-tunnel results as can be determined by present type of pressure measuring apparatus. It is considered that most important data obtained are the coefficients of tail-surface forces and hull-bending moments. These are tabulated in this report.

Burgess, C P↗

NASA NTRS2013

Jet-Surface Interaction Test: Phased Array Noise Source Localization Results

An experiment was conducted to investigate the effect that a planar surface located near a jet flow has on the noise radiated to the far-field. Two different configurations were tested: 1) a shielding configuration in which the surface was located between the jet and the far-field microphones, and 2) a reflecting configuration in which the surface was mounted on the opposite side of the jet, and thus the jet noise was free to reflect off the surface toward the microphones. Both conventional far-field microphone and phased array noise source localization measurements were obtained. This paper discusses phased array results, while a companion paper (Brown, C.A., "Jet-Surface Interaction Test: Far-Field Noise Results," ASME paper GT2012-69639, June 2012.) discusses far-field results. The phased array data show that the axial distribution of noise sources in a jet can vary greatly depending on the jet operating condition and suggests that it would first be necessary to know or be able to predict this distribution in order to be able to predict the amount of noise reduction to expect from a given shielding configuration. The data obtained on both subsonic and supersonic jets show that the noise sources associated with a given frequency of noise tend to move downstream, and therefore, would become more difficult to shield, as jet Mach number increases. The noise source localization data obtained on cold, shock-containing jets suggests that the constructive interference of sound waves that produces noise at a given frequency within a broadband shock noise hump comes primarily from a small number of shocks, rather than from all the shocks at the same time. The reflecting configuration data illustrates that the law of reflection must be satisfied in order for jet noise to reflect off of a surface to an observer, and depending on the relative locations of the jet, the surface, and the observer, only some of the jet noise sources may satisfy this requirement.

Podboy, Gary G.↗

NASA NTRS2012

Jet-Surface Interaction Test: Phased Array Noise Source Localization Results

An experiment was conducted to investigate the effect that a planar surface located near a jet flow has on the noise radiated to the far-field. Two different configurations were tested: 1) a shielding configuration in which the surface was located between the jet and the far-field microphones, and 2) a reflecting configuration in which the surface was mounted on the opposite side of the jet, and thus the jet noise was free to reflect off the surface toward the microphones. Both conventional far-field microphone and phased array noise source localization measurements were obtained. This paper discusses phased array results, while a companion paper discusses far-field results. The phased array data show that the axial distribution of noise sources in a jet can vary greatly depending on the jet operating condition and suggests that it would first be necessary to know or be able to predict this distribution in order to be able to predict the amount of noise reduction to expect from a given shielding configuration. The data obtained on both subsonic and supersonic jets show that the noise sources associated with a given frequency of noise tend to move downstream, and therefore, would become more difficult to shield, as jet Mach number increases. The noise source localization data obtained on cold, shock-containing jets suggests that the constructive interference of sound waves that produces noise at a given frequency within a broadband shock noise hump comes primarily from a small number of shocks, rather than from all the shocks at the same time. The reflecting configuration data illustrates that the law of reflection must be satisfied in order for jet noise to reflect off of a surface to an observer, and depending on the relative locations of the jet, the surface, and the observer, only some of the jet noise sources may satisfy this requirement.

Podboy, Gary G.↗

NASA NTRS1983

Asymmetries of the upper stratospheric ozone distribution between two hemispheres

In connection with the eccentricity of the earth's orbit, conditions of solar radiation are not strictly symmetrical for the two hemispheres. The intensity of solar irradiation is approximately 6.6 percent higher near perihelion than near aphelion. As the ozone densities in the upper stratosphere and mesosphere are mainly controlled by photochemical processes, the asymmetry of irradiation conditions for both hemispheres could result in corresponding asymmetries regarding the ozone content. The present investigation is concerned with this possibility. The investigation takes into account Nimbus-7 and Nimbus-4 satellite data. It is found that the hemispheric asymmetries of the ozone distribution in the summer mesosphere and upper stratosphere are fully ascribable to the hemispheric temperature differences due to the combined effects of the earth's orbital ellipticity and its tilted spin axis from the ecliptic plane. The wintertime hemispheric asymmetries imply the presence of additional effects.

Maeda, K.↗

NASA NTRS1987

Mass distributions in elliptical galaxies at large radii

Recently, X-ray observations have shown that elliptical galaxies generally contain large quantities of hot gas. Central dominant cluster ellipticals have even more gas, which they have accreted from the surrounding clusters. The mass distributions in these galaxies can be derived from the condition of hydrostatic equilibrium. M87, the best studied central dominant galaxy, has a massive, dark halo with a total mass of about 4 x 10 to the 12th solar masses within a radius of 300 kpc. The total mass-to-light ratio within this radius is at least 150 solar mass/solar luminosity. The X-ray observations of normal ellipticals also strongly suggest that they have heavy halos, although the distribution of the mass is much less certain than in M87.

Sarazin, Craig L.↗

NASA NTRS1972

A computer program for the calculation of laminar and turbulent boundary layer flows

The results are presented of a study to produce a computer program to calculate laminar and turbulent boundary layer flows. The program is capable of calculating the following types of flow: (1) incompressible or compressible, (2) two dimensional or axisymmetric, and (3) flows with significant transverse curvature. Also, the program can handle a large variety of boundary conditions, such as blowing or suction, arbitrary temperature distributions and arbitrary wall heat fluxes. The program has been specialized to the calculation of equilibrium air flows and all of the thermodynamic and transport properties used are for air. For the turbulent transport properties, the eddy viscosity approach has been used. Although the eddy viscosity models are semi-empirical, the model employed in the program has corrections for pressure gradients, suction and blowing and compressibility. The basic method of approach is to put the equations of motion into a finite difference form and then solve them by use of a digital computer. The program is written in FORTRAN 4 and requires small amounts of computer time on most scientific machines. For example, most laminar flows can be calculated in less than one minute of machine time, while turbulent flows usually require three or four minutes.

Dwyer, H. A.↗

NASA NTRS1972

NASTRAN thermal analyzer: A general purpose finite element heat transfer computer program

The program not only can render temperature distributions in solids subjected to various thermal boundary conditions, including effects of diffuse-gray thermal radiation, but is fully compatible in capacity and in the finite-element model representation with that of its structural counterpart in the NASTRAN system. The development history of the finite-element approach for determining temperatures is summarized. The scope of analysis capability, program structure, features, and limitations are given with the objective of providing NASTRAN users with an overall veiw of the NASTRAN thermal analyzer.

Lee, H.↗

NASA NTRS1972

Thermal elastoplastic structural analysis of non-metallic thermal protection systems

An incremental theory and numerical procedure to analyze a three-dimensional thermoelastoplastic structure subjected to high temperature, surface heat flux, and volume heat supply as well as mechanical loadings are presented. Heat conduction equations and equilibrium equations are derived by assuming a specific form of incremental free energy, entropy, stresses and heat flux together with the first and second laws of thermodynamics, von Mises yield criteria and Prandtl-Reuss flow rule. The finite element discretization using the linear isotropic three-dimensional element for the space domain and a difference operator corresponding to a linear variation of temperature within a small time increment for the time domain lead to systematic solutions of temperature distribution and displacement and stress fields. Various boundary conditions such as insulated surfaces and convection through uninsulated surface can be easily treated. To demonstrate effectiveness of the present formulation a number of example problems are presented.

Chung, T. J.↗