Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coarse graining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Apollo 16 core 60013/14 as a product of path 1 and path 2 regolith evolution processes

We have made a petrographic study of 12 samples along the 62 cm profile of Apollo 16 core 60013/14 taken at Station 10 near the lunar module. The basic core description and maturity variations have been discussed earlier. This core is important because it enables a stratigraphic comparison with nearby cores 60001-7 and 60009/10. These cores form a triangle with sides 35-40 m. FMR data show a maturity-match between 60009/10 and 60013/14. Unfortunately, segments of the core 60001-7 are too disturbed for any cm scale comparison. We present new data on the grain size distribution and the modal petrography for six samples from six levels of 60013 using the same approach and rationale used for 60014. We have combined the new data with our previous data on 60014 to plot the variations of grain size distributions and grain type abundances, in the 500-1000 m and 90-150 micrometers size fractions, with depth. Agglutinate abundances match the I sub s/FeO profile and both show a significant break at a depth of about 45 cm, with lower maturity material below that point. Grain size distributions show that for all analyzed samples, the mean grain size is below 90 micrometers. The two lowest samples are somewhat more coarse-grained than the rest of the core. The break at about 45 cm is the most prominent feature of the core and was described during the initial dissection as a pronounced change in color from dark to light. It now seems clear that this break is primarily one of maturity rather than of bulk chemical composition.

Basu, A.↗

Effect of Aluminum and Grain Size on the Fracture Behavior of Twinning-Induced Plasticity Steels

The present study investigates the effect of Al and grain size on the notch sensitivity and fracture toughness of twinning-induced plasticity (TWIP) steels. It is evident that the notch sensitivity and fracture toughness of TWIP steels can be improved by the addition of Al and grain refinement. Furthermore, the relatively low fracture toughness and high-notched sensitivity of coarse-grained TWIP steels can be explained by a quasi-cleavage fracture mechanism.

36 MATERIALS SCIENCE↗

The creep properties of dispersion-strengthened silver-gallium oxide alloys.

Steady-state creep rates were measured for two preparations of a dispersion-strengthened alloy of silver with 1 mol % gallium oxide. One preparation, an internally-oxidized type, had a grain size 40 times that of the other preparation, which was a consolidated-powder type of alloy. The temperature and stress dependence of the steady-state creep rate differs widely for the two alloys and must be attributed to the difference in grain size. The activation energy for steady-state creep of the internally-oxidized coarse grained material is near that for self-diffusion of silver, which strongly indicates a creep process controlled by dislocation climb.

Lenel, F. V.↗

Isotopic, optical, and trace element properties of large single SiC grains from the Murchison meteorite

Ion probe mass spectrometry is used to analyze 41 large SiC grains from the Murchison CM2 chondrite, ranging up to 15 x 26 microns, for the isotopic compositions of C, N, Mg, and Si, and the concentrations of Al, Ti, V, Fe, Zr, and Ba. The majority were found to have large isotopic anomalies. Only two grains, characterized by extremely heavy carbon, give evidence for fossil Mg-26. On the basis of C and Si isotopic composition, 29 of the grains fall into three compact clusters, presumably from three discrete sources. The clustering of coarse-grained SiC stands in sharp contrast to the quasi-continuous distribution of finer-grained SiC and suggests that the top 0.1 percent of the mass distribution is a distinct population. The C and N isotopic compositions of the anomalous grains are not very diagnostic, being consistent with H-burning in the CNO cycle. The Si-isotopic compositions qualitatively show the signature of neutron capture in He-burning shells of highly evolved stars.

Virag, Alois↗

Relict grains in chondrules: Evidence for chondrule recycling

The presence of relict grains in chondrules, which offers some insight into the degree to which chondrule material was recycled in the chondrule-forming region, is discussed in this report. Relics are grains that clearly did not crystallize in situ in the host chondrule. They represent coarse-grained precursor material that did not melt during chondrule formation, and provide the only tangible record of chondrule precursor grains. Relics are commonly identified by a large difference in size, textural differences, and/or significant compositional differences compared with normal grains in the host chondrule. Two important types of relics are: (1) 'dusty,' metal-bearing grains of olivine and pyroxene; and (2) forsterite (Mg-rich olivine) grains present in FeO-rich chondrules.

Jones, R. H.↗

Discovery of hydrated Clasts with Very High Abundance of Ferromagnesian 160-Rich Olivine: Inner or Outer Solar System origin?

Olivine is one of the major minerals in chondritic meteorites and occurs in all chondritic components, including amoeboid olivine aggregates (AOAs), forsterite-bearing Type B (FoB) Ca, Al-rich inclusions (CAIs), chondrules, and matrices. As a result, olivines could preserve chemical and isotopic characteristics of their formation environments. There are significant variations in oxygen isotopic compositions of chondritic olivine. Forsteritic olivine in AOAs and FoB-CAIs has solar-like 16O-rich compositions (D17O ~ -23±2‰); the former condensed from an 16O-rich gas of ~solar composition, whereas the latter crystallized from remelted condensates in an isotopic similar gaseous reservoir. Olivine phenocrysts in chondrules are significantly 16O-depleted compared to CAIs and AOAs: D17O ranges from ~ -7 to +3‰. Only rare relict olivines in chondrules have CAI/AOA-like 16O-rich compositions; these grains most likely represent fragments of CAIs and AOAs incompletely melted during chondrule formation. Olivine in matrices of weakly metamorphosed meteorites is extremely fine-grained (<100 nm) and has predominantly forsteritic composition. In metamorphosed chondrites, matrix olivines are coarse-grained (up to 10 μm) and enriched in FeO. Due to small grain sizes, oxygen isotopic compositions of matrix olivines are poorly known. Mapping of matrices of Vigarano and Kakangari using isotope microscopes (secondary ion mass-spectrometer (SIMS) plus SCAPS detector) revealed the presence of 16O-rich olivine grains. While most matrix olivines in Vigarano have 16O-poor compositions, nearly half of olivines measured in Kakangari matrix are16O-rich.Here, we present for the first time new lithologies largely composed of 16O-and Fe-rich olivine. We attempt to address the question of whether these 16O-richolivine grains were formed by condensation in the solar nebula or by a secondary process during the evolution of the parent body. Mineralogical characteristics of these unusual olivines, as well as in-situ measured oxygen-isotope compositions of different phases are reported in detail.

I. Kerraouch↗

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel

Mechanical Performance of traditional gas-shielded arc welded joints of 700 MPa grade microalloyed C-Mn steel cannot meet service requirements. Laser welding, with its characteristic high energy density, is known to improve the welding performance of experimental steels. In the present study, Nb-Ti microalloyed steel with a thickness of 4.5 mm was welded using a 4 kW fiber laser. The microstructure, precipitation, and mechanical properties of the welded joints were studied. The hardness and tensile strength of the welded joints were higher than those of the base metal (BM). The microstructure of the fusion zone (FZ) and coarse grain heat affected zone (CGHAZ) was lath martensite (LM), while the microstructure of the fine grain HAZ and mixed grain HAZ consisted of ferrite and martensite/austenite islands. Although LM was observed in both the FZ and CGHAZ, the hardness and calculated tensile strength of the FZ were lower than those of the CGHAZ, due to a reduction in solid solution strengthening by element loss and the dissolution of high-hardness precipitates in FZ. Most precipitates such as [(Nb,Ti)C and (Nb,Ti)(C,N)] that were present in the BM were dissolved, which led to an increase in C and N in solid solution in the FZ. Thus, the elastic modulus of the FZ was higher than that of the BM. Similarly, the elastic modulus of the CGHAZ was higher than that of the BM due to the segregation of C and N atoms during the welding process. The toughness of the FZ was superior to that of the BM, and the toughness of the HAZ approached 91% of that of the BM. The change in toughness primarily depended on the microstructural refinement, the increase in the fraction of grains with high misorientation, the residual austenite in the FZ and CGHAZ, and the dissolution of coarse precipitates.

36 MATERIALS SCIENCE↗

Unveiling the mechanism of phase and morphology selections during the devitrification of Al-Sm amorphous ribbon

The complex interplay between energetic and kinetic factors that governs the phase and morphology selections can originate at the earliest stage of crystallization in the amorphous parent phases. Because of the extreme difficulties in capturing the microscopic nucleation process, a detailed picture of how initial disordered structures affect the transformation pathway remains unclear. Here, we report the experimental observation of widely varying phase selection and grain size evolution during the devitrification of a homogeneous melt-spun glassy ribbon. Two different crystalline phases, θ-Al 5 Sm and ε-Al 60 Sm 11 , are found to form in the different regions of the same metallic glass ribbon during the devitrification. The grain size of ε-Al 60 Sm 11 phase shows a strong spatial heterogeneity. Coarse-grained ε-Al 60 Sm 11 phase coupled with the small volume fraction of θ-Al 5 Sm phase is preferably formed close to wheel side of the melt-spun ribbon. Combining experimental characterization and computational simulations, we show that phase selection and microstructure evolution can be traced back to different types and populations of atomic clusters that serve as precursors for the nucleation of different crystalline phases. Inhomogeneous cooling rates cause different structure orders across the glass sample during the quenching process. Our findings provide direct insight into the effect of structural order on the crystallization pathways during the devitrification of metallic glass. It also opens an avenue to study the detailed nucleation process at the atomic level using the metallic glass as a platform and suggests the opportunity of microstructure and property design via controlling the cooling process.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Examining the influence of grain size on radiation tolerance in the nanocrystalline regime

Here, nanocrystalline materials have been proposed as superior radiation tolerant materials in comparison to coarse grain counterparts. However, there is still a limited understanding whether a particular nanocrystalline grain size is required to obtain significant improvements in key deleterious effects resulting from energetic irradiation. This work employs the use of in-situ heavy ion irradiation transmission electron microscopy experiments coupled with quantitative defect characterization and precession electron diffraction to explore the sensitivity of defect size and density within the nanocrystalline regime in platinum. Under the explored experimental conditions, no significant change in either the defect size or density between grain sizes of 20 and 100 nm was observed. Furthermore, the in-situ transmission electron microscopy irradiations illustrate stable sessile defect clusters of 1-3 nm adjacent to most grain boundaries, which are traditionally treated as strong defect sinks. The stability of these sessile defects observed in-situ in small, 20-40 nm, grains is the proposed primary mechanism for a lack of defect density trends. Lastly, this scaling breakdown in radiation improvement with decreasing grain size has practical importance on nanoscale grain boundary engineering approaches for proposed radiation tolerant alloys.

36 MATERIALS SCIENCE↗

Microstructure and Strengthening Mechanisms in an Ultrafine Grained Al-Mg-Sc Alloy Produced by Powder Metallurgy

Additions of Sc to an Al-Mg matrix were investigated, paying particular attention to the influence of Al3Sc precipitates and other dispersoids, as well as grain size, on mechanical behavior. Prior studies have shown that Sc significantly increases the strength of coarse-grained Al-Mg alloys. Prompted by these findings, we hypothesized that it would be of fundamental and technological interest to study the behavior of Sc additions to an ultrafine-grained (UFG) microstructure (e.g., 100’s nm). Accordingly, we investigated the microstructural evolution and mechanical behavior of a cryomilled ultrafine grained Al-5Mg-0.4Sc (wt pct) and compared the results to those of an equivalent fine-grained material (FG) produced by powder metallurgy. Experimental materials were consolidated by hot isostatic pressing (HIP’ing) followed by extrusion or dual mode dynamic forging. Under identical processing conditions, UFG materials generate large Al3Sc precipitates with an average diameter of 154 nm and spaced approximately 1 to 3 µm apart, while precipitates in the FG materials have a diameter of 24 nm and are spaced 50 to 200 nm apart. The strengthening mechanisms are calculated for all materials and it is determined that the greatest strengthening contributions for the UFG and FG materials are Mg-O/N dispersion strengthening and precipitate strengthening, respectively.

36 MATERIALS SCIENCE↗

Microstructure and mechanical behavior of direct metal laser sintered Inconel alloy 718

In this paper, we investigate microstructure and quasi-static mechanical behavior of the direct metal laser sintered Inconel 718 superalloy as a function of build direction (BD). The printed material was further processed by annealing and double-aging, hot isostatic pressing (HIP), and machining. We characterize porosity fraction and distribution using micro X-ray computed tomography (μXCT), grain structure and crystallographic texture using electron backscattered diffraction (EBSD), and mechanical response in quasi-static tension and compression using standard mechanical testing at room temperature. Analysis of the μXCT imaging shows that majority of porosity develops in the outer layer of the printed material. However, porosity inside the material is also present. The EBSD measurements reveal formation of columnar grains, which favor < 001 > fiber texture components along the BD. These measurements also show evidence of coarse-grained microstructure present in the samples treated by HIP. Finally, analysis of grain boundaries reveal that HIP results in a large number of annealing twins compared to that in samples that underwent annealing and double-aging. The yield strength varies with the testing direction by approximately 7%, which is governed by a combination of grain morphology and crystallographic texture. In particular, we determine tension–compression asymmetry in the yield stress as well as anisotropy of the material flow during compression. We find that HIP lowers yield stress but improves ductility relative to the annealed and aged material. These results are discussed and critically compared with the data reported for wrought material in the same condition. - Highlights: • Microstructure and mechanical properties of DMLS Inconel 718 are studied in function of build direction. • Inhomogeneity of microstructure in the material in several conditions is quantified by μXCT and EBSD. • Anisotropy and asymmetry in the mechanical response are determined by tension and compression testing.

36 MATERIALS SCIENCE↗

An N-body Tree Algorithm for the Cray T3D

We describe in this paper an algorithm for solving the gravitational N-body problem using tree data structures on the Cray T3D parallel supercomputer. This implementation is an adaptation of previous work where this problem was solved using an SIMD, fine-grained parallel computer. We show here that this approach lends itself, with small modifications, to more coarse-grained parallelism as well. We also show that the performance of the algorithm on the Cray T3D parallel architecture scales adequately with the number of processors (up to 256). Specific levels to be reached using the Cray T3D parallel architecture. A peak performance level of 9.6 Gflop/s is reached on 256 processors for the time critical gravity computation.

Olson, Kevin M.↗

Rescuing complementarity with little drama

The AMPS paradox challenges black hole complementarity by apparently constructing a way for an observer to bring information from the outside of the black hole into its interior if there is no drama at its horizon, making manifest a violation of monogamy of entanglement. We propose a new resolution to the paradox: this violation cannot be explicitly checked by an infalling observer in the finite proper time they have to live after crossing the horizon. Our resolution depends on a weak relaxation of the no-drama condition (we call it “little-drama”) which is the “complementarity dual” of scrambling of information on the stretched horizon. When translated to the description of the black hole interior, this implies that the fine-grained quantum information of infalling matter is rapidly diffused across the entire interior while classical observables and coarse-grained geometry remain unaffected. Under the assumption that information has diffused throughout the interior, we consider the difficulty of the information-theoretic task that an observer must perform after crossing the event horizon of a Schwarzschild black hole in order to verify a violation of monogamy of entanglement. We find that the time required to complete a necessary subroutine of this task, namely the decoding of Bell pairs from the interior and the late radiation, takes longer than the maximum amount of time that an observer can spend inside the black hole before hitting the singularity. Furthermore, an infalling observer cannot observe monogamy violation before encountering the singularity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of Pore Fluid Chemistry on Fine-Grained Sediment Fabric and Compressibility

Fines, defined here as grains or particles, less than 75µm in diameter, exist nearly ubiquitously in natural sediment, even those classified as coarse. Macroscopic sediment properties, such as compressibility, which relates applied effective stress to the resulting sediment deformation, depend on the fabric of fines. Unlike coarse grains, fines have sizes and masses small enough to be more strongly influenced by electrical interparticle forces than by gravity. These electrical forces acting through pore fluids are influenced by pore-fluid chemistry changes. Macroscopic property dependence on pore-fluid chemistry must be accounted for in sediment studies involving subsurface flow and sediment stability analyses, as well as in engineered flow situations such as groundwater pollutant remediation, hydrocarbon migration or other energy resource extraction applications. This study demonstrates how the liquid-limit-based electrical sensitivity index can be used to predict sediment compressibility changes due to pore-fluid chemistry changes. Laboratory tests of electrical sensitivity, sedimentation and compressibility illustrate mechanisms linking micro- and macro-scale processes for selected pure, endmember fines. In conclusion, a specific application considered here is methane extraction via depressurization of gas hydrate-bearing sediment, which causes a dramatic pore-water salinity drop concurrent with sediment being compressed by the imposed effective stress increase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Production of Seamless Superconducting Radio Frequency Cavities from Ultra-fine Grained Niobium, Phase II Final Report

The positron and electron linacs of the International Linear Collider (ILC) will require over 14,000, nine-cell, one meter length, superconducting radio frequency (SRF) cavities [ILC Reference Design Report, 2007]. Manufacturing on this scale will benefit from more efficient fabrication methods. The current methods of fabricating SRF cavities involve deep drawing of the halves of each of the elliptical cells and joining them by high-vacuum, electron beam welding, with at least 19 circumferential welds per cavity. The welding is costly and has undesirable effects on the cavity surfaces, including grain-scale surface roughening at the weld seams. Hydroforming of seamless tubes avoids welding, but hydroforming of coarse-grained seamless tubes results in strain-induced surface roughening. Surface roughness limits accelerating fields, because asperities prematurely exceed the critical magnetic field and become normal conducting. This project explored the technical and economic feasibility of an improved processing method for seamless tubes for hydroforming. Severe deformation of bulk material was first used to produce a fine structure, followed by extrusion and flow-forming methods of tube making. Extrusion of the randomly oriented, fine-grained bulk material proceeded under largely steady-state conditions, and resulted in a uniform structure, which was found to be finer and more crystallographically random than standard (high purity) RRR niobium sheet metal. A 165 mm diameter billet of RRR grade niobium was processed into five, 150 mm I.D. tubes, each over 1.8 m in length, to meet the dimensions used by the DESY ILC hydroforming machine. Mechanical properties met specifications. Costs of prototype tube production were approximately twice the price of RRR niobium sheet, and are expected to be comparable with economies of scale. Hydroforming and superconducting testing will be pursued in subsequent collaborations with DESY and Fermilab. SRF Cavities are used to construct particle accelerators for high-energy physics research, as well as for lower energy particle accelerators, and Free Electron Lasers. These machines have applications in the fields of basic science, industrial processing, medical diagnostics, pharmaceutical research and weapons systems. The scientific community and the general public will benefit from the implementation of this technology since lower production costs will increase the availability of SRF particle accelerators.

36 MATERIALS SCIENCE↗

Rocks 60618 and 65785 - Evidence for admixture of KREEP in lunar impact melts

We present evidence to support the hypothesis that the fine-grained, basaltic-textured portions of rocks 60618 and 65785 were produced by impact melting of the coarse-grained spinel-olivine anorthosite (60618) and spinel troctolite (65785) portions, coupled with admixture of approximately 33% and 63%, respectively, material of alkalic high-alumina basalt (KREEP) composition. The abundance of impact-modified rocks at the Apollo 16 site with compositional similarities to the impact melts reported here, suggests that the relations observed in these rocks are indicative of widespread impact mixing with KREEP in rocks of the lunar highlands.

Keil, K.↗

Recrystallization characteristics of oxide dispersion strengthened nickel-base alloys

Electron microscopy was employed to study the process of recrystallization in two oxide dispersion strengthened (ODS) mechanically alloyed nickel-base alloys, MA 754 and MA 6000E. MA 754 contained both fine, uniformly dispersed particles and coarser oxides aligned along the working direction. Hot rolled MA 754 had a grain size of 0.5 microns and high dislocation densities. After partial primary recrystallization, the fine grains transformed to large elongated grains via secondary (or abnormal) grain growth. Extruded and rolled MA 6000E contained equiaxed grains of 0.2 micron diameter. Primary recrystallization occurring during working eliminated virtually all dislocations. Conversion from fine to coarse grains was triggered by gamma prime dissolution; this was also a process of secondary or abnormal grain growth. Comparisons were made to conventional and oxide dispersion strengthened nickel-base alloys.

Hotzler, R. K.↗

Influence of grain size on the creep behavior of HfC-dispersed NiAl

Rapid solidification technology has been utilized to produce a NiAl-4(wt pct)HfC composite containing about 0.3 vol pct HfC as dispersed 50 nm particles. Study of the 1300 K compressive creep properties demonstrated that the initial, small grain size microstructure was unstable under slow strain rate deformation conditions. The grain growth which occurred during testing led to considerable strengthening. Subsequent measurements of the creep properties of the coarse grained specimens revealed that this strength was achieved by a large increase in the activation energy for deformation without any change in the stress exponent. Based on this work, it is concluded that large grain microstructures will be required for optimum elevated temperature creep properties in dispersed NiAl.

Whittenberger, J. D.↗