Results for “Ceramic matrix composites” — Page 46

NASA NTRS2020

Influence of Thermally-Grown Oxide (TGO) Layer on the Driving Forces Associated with Failure in Environmental Barrier Coating (EBC) Systems

Environmental barrier coatings (EBC) is an enabling technology for the successful application of ceramic matrix composites (CMCs) in air-breathing gas turbine engines. Spallation of environmental barrier coating (EBC) induced by thermally grown oxide (TGO) layer is a key EBC failure mode. The TGO layer, resulting from steam oxidation, grows either from a silicon bond coat layer (if present) or from the silicon carbide (SiC) based substrate itself. Critical thickness of the TGO layer for failure is in the range of 20-30 microns but it can vary due to exposure temperature, microstructure etc. Current work at NASA Glenn Research Center, under the Revolutionary Tools and Methods (RTM) project is aimed at addressing associated failure modes in EBC systems and developing robust analysis tools to aid in the design/analysis of these systems. The objective of the current work is to conduct a sensitivity study to examine the influence of uniformly and non-uniformly grown oxide layers with or without damage on the associated driving forces leading to spallation of the EBC when subjected to isothermal loading. Initial results indicate that the presence of damage (vertical cracks caused by in-plane stresses) enhances the stresses that are present due to non-uniformity. However, the presence of non-uniformity itself is still the main factor influencing the magnitude of peel and shear stresses in the TGO layer.

Mital, Subodh K.↗

NASA NTRS2020

Advancing Development of Environmental Barrier Coatings Resistant to Attack by Molten Calcium-Magnesium-Aluminosilicate (CMAS)

Ceramic matrix composites (CMCs) are a leading material system to replace metal-based parts in the hot-section of air-breathing turbine engines to improve fuel efficiency in aircraft engines. CMCs have higher temperature capabilities and lower density compared with traditional metallic structural materials. However, silicon-based CMCs are susceptible to oxidation in the harsh combustion environment encountered in turbine engines. Consequently, environmental barrier coatings (EBCs) are being developed to protect CMC components to improve durability and extend service life of CMCs. Sand, volcanic ash and other particulate debris, which are generally comprised of calcium-magnesium-aluminosilicate (CMAS) and other trace oxides, are routinely ingested by aircraft engines. At temperatures above 1200Â°C, CMAS particulates melt. Near target operating temperatures (~1500Â°C) of future CMC-based aircraft engines, molten CMAS behaves like a viscous melt that can infiltrate and chemically interact with protective coatings. These interactions can cause premature failure of the EBC system and ultimately the overall CMC engine component. Degradation of candidate EBC materials by molten CMAS will be presented with a focus on recent work, as well as methods of evaluating the complex high-temperature materials interactions, underway at NASA Glenn Research Center.

Wiesner, Valerie L.↗

NASA NTRSDate not supplied

TPSAS-NF1676L-16463-DND

Ceramic Matrix Composites (CMCs) have been proposed for hot structures in scramjet combustors. Previous studies have calculated significant weight savings by utilizing CMCs (active and passive) versus actively cooled metallic scramjet structures. Both a C/C and a C/C-SiC material system fabricated by DLR (Stuttgart, Germany) are being considered for use in a passively cooled combustor design for HIFiRE 8, a joint Australia / AFRL hypersonic flight program, expected to fly at Mach 7 for ~ 30 sec, at a dynamic pressure of 55 kPa. Flat panels of the DLR C/C and the C/C-SiC were tested in the NASA Langley Direct Connect Rig (DCR) at Mach 5 and Mach 6 enthalpy for several minutes. Gaseous hydrogen fuel was used to fuel the scramjet combustor. The test panels were instrumented with embedded Type K and Type S thermocouples. Zirconia felt insulation was used in some of the tests to increase the surface temperature of the C/C-SiC panel ~ 350?F. The final C/C-SiC panel was tested for 3 cycles totaling over 135 sec at Mach 6 enthalpy. Slightly more erosion was observed on the C/C panel than the C/C-SiC panels, but both material systems demonstrated acceptable recession performance for the HIFiRE 8 flight.

David E Glass↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Paul W Giel↗

NASA NTRS2020

Special Issue: Environmental Barrier Coatings

The global increase in air travel will require commercial vehicles to be more efficient than ever before. Advanced turbine hot section materials are a key technology required to keep fuel consumption and emission to a minimum. Ceramic matrix composites (CMCs) are the most promising material to revolutionize turbine hot section materials because of their excellent high‐temperature properties. Rapid surface recession due to volatilization by water vapor is the Achilles heel of CMCs. Environmental barrier coatings (EBCs), which protect CMCs from water vapor, is an enabling technology for CMCs. The first CMC component entered into service in 2016 in a commercial engine, and more CMC components are scheduled to follow within the next few years. One of the most difficult challenges to CMC components is EBC durability because failure of EBC leads to a rapid reduction in CMC component life. Novel EBC chemistries, creative EBC designs, and robust processes are required to meet EBC durability challenges. Engine-relevant testing, characterization, and lifing methods need to be developed to improve EBC reliability. The aim of this Special Issue is to present recent advances in EBC technology to address current EBC challenges.

EBC, CMC, Oxidation, Volatility, CMAS, Thermomecha↗

NASA NTRS2020

Tensile Creep Behavior of SiC(f)/SiC Ceramic Matrix Minicomposites

Single fiber-tow minicomposites represent the major load-bearing element of woven and laminate ceramic matrix composites (CMCs). To understand the effects of fiber type, fiber content, and matrix cracking on tensile creep in SiCf/SiC CMCs, single-tow SiCf/SiC minicomposites with different fiber types and contents were investigated. The minicomposites studied contained either Hi-Nicalon™ or Hi-Nicalon™ Type S SiC fibers with a boron nitride (BN) interphase and a chemical-vapor-infiltrated-silicon-carbide (CVI-SiC) matrix. Tensile creep was performed at 1200 °C in air. A bottom-up creep modeling approach was applied where creep parameters of the fibers and matrix were obtained separately at 1200 °C. Next, a theoretical model based on the rule of mixtures was derived to model the fiber and matrix creep-time-dependent stress redistribution. Fiber and matrix creep parameters, load transfer model results, and numerical modeling were used to construct a creep strain model to predict creep damage evolution of minicomposites with different fiber types and contents.

SiC/SiC Minicomposites Creep↗

NASA NTRSDate not supplied

Effects of Trailing Edge Thickness and Blade Loading Distribution on the Aerodynamic Performance of Simulated CMC Turbine Blades

The aerodynamic performance of three blade sets that represent the geometric manufacturing constraints of Ceramic Matrix Composite (CMC) blades was measured experimentally in a large-scale transonic turbine blade cascade. The trailing edge thicknesses of CMC blades are anticipated to be significantly larger than those of current state-of-the-art metallic blades. The blades tested in the current study had trailing edge thicknesses of 5%, 7%, and 9% relative to the blade axial chord. The three blade sets were designed with matching throat dimensions, so the blade loading distributions were varied to retain similar overall loading levels. Data were acquired at four Reynolds numbers, covering a factor of six range. All data were acquired at the design isentropic exit Mach number of 0.74. Measurements include blade loading and five-hole probe surveys at two downstream stations. The effects of inlet turbulence intensity were also quantified. Total pressure loss data were integrated to determine overall loss levels for each of the three measured blade passages. Excellent periodicity was noted. For low inlet turbulence levels, losses were surprisingly lower for the thickest trailing edge at low Reynolds numbers, but were highest at the maximum Reynolds number. In general, losses were found to scale well with Reynolds number, although front loading was found to significantly reduce the sensitivity of loss to Reynolds number. For high inlet turbulence intensity, losses were found to scale with trailing edge thickness as expected, and the Reynolds number sensitivity was reduced for all three blade sets. Loss levels at the highest Reynolds number were comparable at low and high inlet turbulence intensity levels.

Turbine↗

NASA NTRS2021

Modeling of the Influence of Thermally Grown Oxide (TGO) Layers on the Driving Forces in Environmental Barrier Coating Systems

Environmental barrier coatings (EBC) are an enabling technology for the successful application of ceramic matrix composites (CMCs) in air-breathing gas turbine engines. EBCs are susceptible to several failure modes including oxidation/delamination, recession, chemical attack and dissolution, thermomechanical degradation, erosion, and foreign object impact damage in a combustion environment. Spallation of environmental barrier coating (EBC), induced by a thermally grown oxide (TGO) layer, is a key EBC failure mode. The TGO layer, resulting from steam oxidation, grows either from a silicon bond coat layer (if present) or from a silicon carbide (SiC) based substrate itself. The TGO layer evolves (i.e., thickness increases with time) as water vapor and oxygen gradually diffuse through the EBC, and the EBC spalls off once the TGO layer reaches some critical thickness. The critical thickness of the TGO layer for failure is in the range of 20-30 microns, with the actual value depending upon exposure temperature, microstructure, etc. Current work at NASA Glenn Research Center, under the Transformative Tools and Technology (TTT) subproject is aimed at addressing associated failure modes in EBC systems and developing robust analysis tools to aid in the design/analysis of these systems. The objective of the current work is to conduct a sensitivity study to examine the influence of uniformly and non-uniformly grown oxide layers on the associated driving forces leading to spallation of the EBC when subjected to isothermal loading. The effect of damage in the TGO layer on the resulting stress states is also assessed both in uniform and non-uniform TGO layers.

Coatings↗

NASA NTRS2022

Natural Gas/Oxygen Burner Rig at The NASA Glenn Materials Research Laboratory

This technical memorandum describes the development of a new natural gas/oxygen (NG/O2) fueled burner rig to be used for high-temperature environmental durability studies of advanced materials and components at atmospheric pressure. The burner simulates the high-temperature, high-heat flux, and high-velocity thermal environments encountered in aerospace applications. It will be used to study environmental effects such as water vapor interactions relevant to advanced gas turbine engine materials such as ceramic matrix composites with protective environmental barrier coatings. The highest sample temperature achieved to date in a study of the oxidation and recession of monolithic silicon carbide is 3000 °F.

Burner Rig↗

NASA NTRSDate not supplied

A Machine Learning-Derived Atomistic Potential for Y2Si2O7

Incorporation of SiC/SiC ceramic matrix composite (CMC) hot section components into aircraft engines promises to increase efficiency and safety. However, SiC/SiC CMCs are subject to water vapor-induced oxidation and recession at the high temperatures of engine operation, and thus environmental barrier coatings (EBCs) are required to reduce this degradation and enable their widespread adoption. An understanding of EBCs failure mechanisms, including thermochemical and thermomechanical mechanisms, is essential as coating degradation leads to reduced CMC component service life. Computational modeling approaches can provide insight into EBC material properties important for coating design. However, density functional theory (DFT) is computationally expensive and atomistic potentials are lacking for materials of interest. In this work, we utilize a machine learning approach and DFT training data to parameterize atomistic potentials for two candidate EBC materials, Y2Si2O7 and Yb2Si2O7. These potentials enable near DFT-accurate calculations of thermodynamic and thermomechanical properties essential to EBC design.

Cameron J Bodenschatz↗

NASA NTRSDate not supplied

Thermochemical/Thermomechanical Synergies in High Temperature Solid Particle Erosion of CMAS-Exposed EBCs

Environmental barrier coatings (EBCs) are an enabling technology for the use of SiC-based ceramic matrix composites in next generation gas turbine engines. In the extreme engine environment, EBCs must be able to withstand a variety of individual damage mechanisms and their interactions with each other. Ingested particulates/debris can cause both thermochemical and thermomechanical degradation of EBCs. Siliceous debris primarily based on calcium magnesium aluminosilicates (CMAS) can melt and infiltrate and/or react with EBCs above >1200°C. Similarly, ingested debris can lead to mechanical damage and recession of coatings due to particulate erosion. Both modes of degradation can occur simultaneously during engine operation, and it is crucial to comprehensively understand the mechanisms of coating failure due to high-temperature particulate interactions. This study assesses the erosion durability of Yb2Si2O7-based EBCs exposed to CMAS of various loads in NASA Glenn’s Erosion Burner Rig Facility. CMAS exposures and erosion testing were carried out at 1316°C. The effects of CMAS loading and exposure time on EBC erosion durability were evaluated using Al2O3 as an erodent material.

EBC↗

NASA NTRSDate not supplied

Varying Processing Parameters in the Development of Slurry-Based Oxide Bond Coat for Environmental Barrier Coatings

Silicon carbide (SiC)-based ceramic matrix composites (CMCs) are replacing nickel-base superalloys in some hot-section aircraft engine materials due to their lower density and higher working temperature. CMCs require an environmental barrier coating (EBC) for protection from corrosive combustion species. Current-generation EBCs consist of a rare earth silicate topcoat and a silicon bond coat; however, the relatively low melting point of silicon (1414°C) limits the upper use temperature of these coatings. To extend the capability of next-generation EBCs, an oxide-based bond coat capable of withstanding temperatures of up to 1480°C has been developed at NASA Glenn Research Center. In this study, the oxide-based bond coat was applied to monolithic SiC via a slurry coating process. Parameters including slurry particle size and viscosity were varied, and coating performance was evaluated after steam cycling at 1480°C. The effect of including different rare earth constituents in the bond coat was also explored.

R. I. Webster↗

NASA NTRSDate not supplied

The Effect of Trailing Edge Grid Resolution in Large-Eddy Simulations

Ceramic Matrix Composite (CMC) with environmental barrier coating can tolerate significantly higher temperatures compared with the conventional metal alloy blades and thus can help achieve higher thermal efficiency in gas turbine engines. Due to the complex fabrication process of CMC blades, larger blade trailing edge thicknesses and larger leading-edge radii of curvature are expected. These features significantly alter aerodynamic performance especially near the trailing edge and thus the loss profile. In previous studies, the authors used the large eddy simulation (LES) as well as the Reynolds Averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model to simulate an aerodynamics performance of three different CMC blades and compared the predictions against the data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Although we were able to successfully predict different characteristics of aerodynamic performance among three different blades (e.g., pressure loading and integrated losses), LES consistently predicted a small recirculation bubble at the end of the suction side. This was not inconsistent with the physics of the flow, but the pressure loading, locally, near the trailing edge, and as a result, the measured wake profiles did not match the experimental data. To delve further into these issues, a new LES grid with a much finer mesh near the trailing edge was generated where the spanwise extent of the grid was increased by 50%. An LES simulation for the CMC blade with the largest trailing edge thicknesses at the high-freestream turbulence (Tu=13%) condition showed that using such a mesh is necessary for LES to accurately capture the transition phenomena on the suction side. The resulting total pressure coefficient profile and the shift of the wake profile were greatly improved.

CMC↗

NASA NTRSDate not supplied

Thermochemical/Thermomechanical Synergies in High-Temperature Solid Particle Erosion of CMAS-Exposed EBCs

Environmental barrier coatings (EBCs) are an enabling technology for the use of SiC-based ceramic matrix composites in next generation gas turbine engines. In the extreme engine environment, EBCs must be able to withstand a variety of individual damage mechanisms and their interactions with each other. Ingested particulates/debris can cause both thermochemical and thermomechanical degradation of EBCs. Siliceous debris primarily based on calcium magnesium aluminosilicates (CMAS) can melt and infiltrate and/or react with EBCs above 1200°C. Similarly, ingested debris can lead to mechanical damage and recession of coatings due to particulate erosion. Both modes of degradation can occur simultaneously during engine operation, and it is crucial to comprehensively understand the mechanisms of coating failure due to high-temperature particulate interactions. This study assesses the erosion durability of Yb 2 Si 2 O 7 -based EBCs exposed to CMAS of various loads in NASA Glenn’s Erosion Burner Rig Facility. CMAS exposures and erosion testing were carried out at 1316°C. The effects of CMAS loading and exposure time on EBC erosion durability were evaluated using Al 2 O 3 as an erodent material.

CMAS↗

NASA NTRS2023

Nasa Hytec CMC Turbine Blade Durability

The objective of the CMC turbine blade durability program is to identify critical material and design parameters that affect durability of ceramic matrix composite (CMC) turbine blades. A baseline architecture for a cooled high-pressure turbine (HPT) CMC blade and accompanying sub-component test articles were developed with the intent to demonstrate through analysis and subcomponent testing how material and design parameters impact key failure modes. As part of this program, a notional architecture for a cooled CMC blade was matured through a design review rhythm to produce a blade test article containing the necessary features required for operation in an engine like environment. Further validation of the durability of these features were achieved through coupon and sub-component testing to demonstrate the durability of cooling hole configurations and blade attachment designs. Analytical methods were also used to evaluate the acceptability of the baseline blade test article architecture against relevant design requirements and identify abatement and recommended changes to key design drivers to improve component durability for future design iterations.

CMC, Blade↗

NASA NTRSDate not supplied

Thermochemical/Thermomechanical Synergies in High Temperature Solid Particle Erosion of CMAS Exposed EBCs

Environmental barrier coatings (EBCs) are an enabling technology for the use of SiC-based ceramic matrix composites in next generation gas turbine engines. In the extreme engine environment, EBCs must be able to withstand a variety of individual damage mechanisms and their interactions with each other. Ingested particulates/debris can cause both thermochemical and thermomechanical degradation of EBCs. Siliceous debris primarily based on calcium magnesium aluminosilicates (CMAS) can melt and infiltrate and/or react with EBCs above >1200°C. Similarly, ingested debris can lead to mechanical damage and recession of coatings due to particulate erosion. Both modes of degradation can occur simultaneously during engine operation, and it is crucial to comprehensively understand the mechanisms of coating failure due to high-temperature particulate interactions. This study assesses the erosion durability of Yb 2 Si 2 O 7 -based EBCs exposed to CMAS of various loads in NASA Glenn’s Erosion Burner Rig Facility. CMAS exposures and erosion testing were carried out at 1316°C. The effects of CMAS loading and exposure time on EBC erosion durability were evaluated using Al2O3 as an erodent material.

EBC↗

NASA NTRSDate not supplied

The Effect of Trailing Edge Grid Resolution in Large-Eddy Simulations

Ceramic Matrix Composite (CMC) with environmental barrier coating can tolerate significantly higher temperatures compared with the conventional metal alloy blades and thus can help achieve higher thermal efficiency in gas turbine engines. Due to the complex fabrication process of CMC blades, larger blade trailing edge thicknesses and larger leading-edge radii of curvature are expected. These features significantly alter aerodynamic performance especially near the trailing edge and thus the loss profile. In previous studies, the authors used the large eddy simulation (LES) as well as the Reynolds Averaged Navier-Stokes (RANS) coupled with an intermittency function-based transition model to simulate an aerodynamics performance of three different CMC blades and compared the predictions against the data acquired at NASA Glenn Transonic Turbine Blade Cascade Rig. Although we were able to successfully predict different characteristics of aerodynamic performance among three different blades (e.g., pressure loading and integrated losses), LES consistently predicted a small recirculation bubble at the end of the suction side. This was not inconsistent with the physics of the flow, but the pressure loading, locally, near the trailing edge, and as a result, the measured wake profiles did not match the experimental data. To delve further into these issues, a new LES grid with a much finer mesh near the trailing edge was generated where the spanwise extent of the grid was increased by 50%. An LES simulation for the CMC blade with the largest trailing edge thicknesses at the high-freestream turbulence (Tu=13%) condition showed that using such a mesh is necessary for LES to accurately capture the transition phenomena on the suction side. The resulting total pressure coefficient profile and the shift of the wake profile were greatly improved.

LES↗

NASA NTRSDate not supplied

Machine Learning Approaches for Rare-Earth Silicate Environmental Barrier Coating Thermochemical and Thermomechanical Property Predictions

Environmental barrier coatings (EBCs) are a necessary enabling technology for the transition from superalloys to silicon carbide (SiC) ceramic matrix composites (CMCs) in gas turbine engines for increased efficiency and decreased fuel costs. SiC-based CMCs are prone to oxidation-based degradation in the engine hot section, and rare-earth (RE) silicates are promising candidates for EBCs due to their close thermal expansion match to the composite substrate and oxidation resistance. However, the design of EBCs is hindered by the large chemical space of candidate materials and the difficulty in obtaining material properties for engineering optimization. This is especially difficult as research continues into mixed-cation or “high-entropy” RE silicates. First-principles computational methods such as density functional theory (DFT) are highly effective at calculating material properties to guide coating design but are limited by their computational cost. Atomistic simulations have the potential to both accelerate property calculations and expand the properties able to be calculated due to their lower computational compared to DFT. However, they require interatomic potentials (IAPs) specific to the material system of interest, and, to our knowledge, there are no suitable IAPs for RE silicates. Machine learning (ML) is a promising technique to accelerate material property predictions indirectly by generating IAPs for atomistic simulations or via direct prediction. In this work, we present two ML approaches to accelerate the calculation of RE silicate properties relevant to EBC design: 1) a ML-derived interatomic potential (IAP) for atomistic simulations of yttrium disilicate (Y2Si2O7) from DFT training data, and 2) a neural network (NN) model to directly predict thermochemical properties of RE silicates and oxides directly from easily obtainable unit cell parameters. Classical MD simulations using the IAP yield lattice properties and bond lengths in good agreement with both DFT and experimental results from x-ray diffraction. Thermodynamic properties calculated using the finite-displacement phonon method and quasi-harmonic approximation were orders of magnitude faster than DFT with good agreement to the DFT results. The IAP was also used to calculate properties such as coefficient of thermal expansion (CTE) that require large simulation supercells and are therefore difficult with DFT. The IAP correctly predicted the anisotropic nature of the CTE in three different phases of Y2Si2O7. The NN model predicts constant pressure heat capacity, Cp, orders of magnitude faster than DFT calculations, which can enable its use as a surrogate model for multiscale simulations. The two methods presented in this work demonstrate the utility of ML for accelerating the prediction of RE silicate properties, which can in turn accelerate EBC design and optimization.

machine learning↗