SEARCH · Engineering Papers

Results for “CONCENTRATION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Effects of Glymes on the Distribution of Mg(B 10 H 10 ) and Mg(B 12 H 12 ) from the Thermolysis of Mg(BH 4 ) 2

We examined the effects of concentrations and identities of various glymes, from monoglyme up to tetraglyme, on H 2 release from the thermolysis of Mg(BH 4 ) 2 at 160–200 °C for 8 h. 11 B NMR analysis shows major products of Mg(B 10 H 10 ) and Mg(B 12 H 12 ); however, their relative ratio is highly dependent both on the identity and concentration of the glyme to Mg(BH 4 ) 2 . Selective formation of Mg(B 10 H 10 ) was observed with an equivalent of monoglyme and 0.25 equivalent of tetraglyme. However, thermolysis of Mg(BH 4 ) 2 in the presence of stoichiometric or greater equivalent of glymes can lead to unselective formation of Mg(B 10 H 10 ) and Mg(B 12 H 12 ) products or inhibition of H 2 release.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2005

Measurement and Characterization of Concentrator Solar Cells II

Concentrator solar cells are continuing to get more consideration for use in power systems. This interest is because concentrator systems can have a net lower cost per watt in solar cell materials plus ongoing improvements in sun-tracking technology. Quantitatively measuring the efficiency of solar cells under concentration is difficult. Traditionally, the light concentration on solar cells has been determined by using a ratio of the measured solar cell s short circuit current to that at one sun, this assumes that current changes proportionally with light intensity. This works well with low to moderate (<20 suns) concentration levels on "well-behaved" linear cells but does not apply when cells respond superlinearly, current increases faster than intensity, or sublinearly, current increases more slowly than intensity. This paper continues work on using view factors to determine the concentration level and linearity of the solar cell with mathematical view factor analysis and experimental results [1].

Scheiman, Dave↗

NASA NTRS1992

Variations in the methanesulfonate to sulfate molar ratio in submicrometer marine aerosol particles over the south Pacific Ocean

Seawater concentrations of dimethylsulfide (DMS) and atmospheric concentrations of DMS, sulfur dioxide, methanesulfonate (MSA), and non-sea-salt (nss) sulfate were measured over the eastern Pacific Ocean between 105 deg and 110 deg W from 20 deg N to 60 deg S during February and March 1989. Although the samples collected in the Southern Hemisphere appear to be of marine origin, no significant correlation was found between the latitudinal distributions of DMS, SO2, MSA, and nss SO4(2-). However, an inverse correlation was found between atmospheric temperature and the MSA to nss SO4(2-) molar ratio in submicrometer aerosol particles with a decrease in temperature corresponding to an increase in the molar ratio. Although this trend is consistent with laboratory results indicating the favored production of MSA at lower temperatures, it is contrary to Southern Hemisphere baseline station data. This suggests either a decrease in the supply of DMS relative to nonmarine sources of nss SO4(2-) at the baseline stations in winter or additional mechanisms that affect the relative production of MSA and nss SO4(2-).

Bates, Timothy S.↗

NASA NTRS1978

Experimental and analytical study of nitric oxide formation during combustion of propane in a jet-stirred combustor

A jet-stirred combustor, constructed of castable zirconia and with an Inconel injector, was used to study nitric oxide formation in propane-air combustion with residence times in the range from 3.2 to 3.3 msec and equivalence ratios varying from 0.7 to 1.4. Measurements were made of combustor operating temperature and of nitric oxide concentration. Maximum nitric oxide concentrations of the order of 55 ppm were found in the range of equivalence ratio from 1.0 to 1.1. A finite-rate chemical kinetic mechanism for propane combustion and nitric oxide formation was assembled by coupling an existing propane oxidation mechanism with the Zeldovich reactions and reactions of molecular nitrogen with hydrocarbon fragments. Analytical studies using this mechanism in a computer simulation of the experimental conditions revealed that the hydrocarbon-fragment-nitrogen reactions play a significant role in nitric oxide formation during fuel-rich combustion.

Wakelyn, N. T.↗

DOE OSTI2021

Simultaneous Isotopic Analysis of U, Pu, and Am in Spent Nuclear Fuel by Resonance Ionization Mass Spectrometry

Solid samples of spent nuclear fuel were analyzed for actinide isotopic composition by resonance ionization mass spectrometry. Isotopes of U, Pu, and Am were simultaneously quantified using a new method that removes and/or resolves the isobaric interferences at 238 U/ 238 Pu and 241 Pu/ 241 Am without sample preparation other than cutting and mounting small (~10 μm) samples. Trends in burnup and neutron capture product distributions were correlated with the sampling positions inside the reactor. Overall, the results show the skin effect, in which the core and near-edge regions of a fuel pellet exhibit strong differences in actinide concentrations and isotope distributions due to differences in the neutron energy spectra between the pellet rim and the core. While no elemental concentration measurements were made, the ability to measure the 238 Pu/ 239 Pu ratio in the presence of a 7400× excess of 238 U enabled an estimate of the enhancement in Pu concentration due to the skin effect at the rim of the pellet.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

NASA NTRS1976

Diurnal and seasonal variations in atomic and molecular oxygen inferred from Atmosphere Explorer-C

Mass-spectrometer measurements of O and N2, obtained with the Atmosphere Explorer-C satellite during December 1974 and January 1975, are used to derive the O2 concentration near 250 km from several ionization reactions. In order to separate temperature effects from diffusion effects, the measured O and inferred O2 concentrations are employed to determine, under the assumption of diffusive equilibrium, the O/N2 and O2/N2 ratios at 120 km. It is found that the latitudinal and diurnal variations in the O concentration at 120 km are consistent with previous results obtained with OGO 6 and that the O2 concentration in the Northern (winter) Hemisphere is about twice as high as that in the Southern (summer) Hemisphere. The possible importance of photodissociation in the diurnal O2 variations is discussed.

Mayr, H. G.↗

DOE OSTI2025

Assessment of Low-Level Pu Isotope Ratio Measurements Using Multicollector Inductively Coupled Plasma Mass Spectrometry (MC-ICP-MS/MS) Equipped with a Pre-Mass Filter

We present an initial investigation into the performance of a multicollector inductively coupled plasmamass spectrometer equipped with a pre-mass filter (Neoma MC-ICP-MS/MS) for making plutonium (Pu) isotope ratio measurements on solutions containing low level (i.e., pg mL –1 ) Pu concentrations. This assessment was achieved by comparison of the 240 Pu/ 239 Pu, 241 Pu/ 239 Pu, and 242 Pu/ 239 Pu ratios attained over a one month period on the MC-ICP-MS/MS with the long-term (∼1 year) performance observed on the predecessor MC-ICP-MS (Neptune Plus) instrument each equipped with an equipped with an APEXΩ desolvating nebulizer for repeated measurements of certified reference materials from New Brunswick Program Office (NBL PO) CRM 136a and CRM 137. The MC-ICP-MS/MS performance of repeated measurement of CRM 136a (n = 20) resulted in mean values of 240 Pu/ 239 Pu = 0.1448 ± 0.0006, 241 Pu/ 239 Pu = 0.00371 ± 0.00006, and 242 Pu/ 239 Pu = 0.00682 ± 0.00006 (k = 2). The CRM 137 (n = 20), analyzed during the same analytical sessions, produced mean values for 240 Pu/ 239 Pu = 0.2414 ± 0.0006, 241 Pu/ 239 Pu = 0.00464 ± 0.00007, and 242 Pu/ 239 Pu = 0.0157 ± 0.0001 (k = 2). These results closely align with the certificate values for CRM 136a and CRM 137 and are within the k = 2 envelopes defined by the long-term performance of the traditional MC-ICP-MS approach (Neptune Plus). Examination of the performance of the various Pu isotope ratios as a function of total Pu content revealed accurate results (<3% relative difference, or RD) above ∼50 fg total Pu. The results presented here demonstrate the capability of the MC-ICP-MS/MS making accurate and precise low level Pu isotopic measurements. While the intent of this work was not to investigate the functionality of the collision cell, the pre-mass filter was employed. Future studies are warranted to investigate the entire capability of the MC-ICP-MS/MS collision cell and pre-cell mass filter optimization for performing low level Pu isotope measurements, even in mixed matrix samples.

CRM↗

NASA NTRS1973

Atomic oxygen transport in the thermosphere.

The photodissociation of oxygen in the lower thermosphere is evaluated to obtain its global average value and the hemispheric imbalance. The observed concentrations of atomic oxygen do not reflect this imbalance in production due to the effect of seasonal wind patterns redistributing the atomic oxygen. The wind system necessary to compensate for the imbalance in solar thermal input into the lower thermosphere is found to transport an amount of atomic oxygen sufficient to compensate for the hemispheric imbalance in production. Ionospheric data indicate a winter enhancement in atomic oxygen concentration; to produce this, a higher degree of oxygen dissociation than that normally accepted (i.e., higher than an atomic to molecular oxygen ratio of unity at 120 km) is needed. The concept that the concentrations of atomic oxygen observed over the winter polar region are maintained by transport from lower latitudes requires that eddy diffusion coefficients derived from vertical transport at low latitudes (ignoring horizontal transport) be reduced by about 25%.

Johnson, F. S.↗

DOE OSTI2024

The Mobility of Mo during Microbially Mediated Ferrihydrite Phase Transformation

Molybdenum (Mo) is an essential nutrient for almost all organisms. However, at high concentrations, it can be toxic to animals and plants. This study investigated the interactions of Mo(VI) with iron oxyhydroxides during ferrihydrite bioreduction in the presence of the Fe(III)- reducing Geobacter sulfurreducens. Here, in this study, we showed that Mo concentration controlled ferrihydrite phase transformation, leading to Mo release. With the biotic reduction of ferrihydrite and Fe(II) production, Mo(VI) reduction and Mo(IV)O 2 formation were observed for the first time, which further immobilised Mo after surface adsorption of Mo(VI). At low Mo levels (Mo/Fe molar ratios of 1-2 %), sufficient Fe(II) adsorption onto ferrihydrite resulted in its transformation into magnetite nanoparticles (>80%, ~25 nm) which catalysed the reduction of Mo(VI) to form Mo(IV)O 2 and immobilised Mo. Contrastingly, at high Mo concentrations (Mo/Fe molar ratios of 5-10%), Mo(VI)O 4 2- adsorption onto ferrihydrite limited Fe(II) adsorption, subsequently less magnetite (<8-12%) formed while more goethite (~30- 50%, width & length > 15 & 100 nm, respectively) and siderite (~20-30%, width & length > 100 & 200 nm, respectively) with larger particle sizes formed instead, causing Mo(VI) release due to lower Mo adsorption. This study provides a comprehensive understanding of the interaction mechanisms among Geobacter sulfurreducens, Mo(VI), and iron oxyhydroxides, enabling predictions and controls of long-term Mo mobility and Fe mineral transformation under a variety of biogeochemical scenarios.

Geobacter sulfurreducens↗

DOE OSTI2021

Fine Aerosol Acidity and Water during Summer in the Eastern North Atlantic

Aerosol pH governs many important atmospheric processes that occur in the marine boundary layer, including regulating halogen and sulfur chemistries, and nutrient fertilization of surface ocean waters. In this study, we investigated the acidity of PM1 over the eastern North Atlantic during the Aerosol and Cloud Experiments in Eastern North Atlantic (ACE-ENA) aircraft campaign. The ISORROPIA-II thermodynamic model was used to predict PM1 pH and water. We first investigated the sensitivities of PM1 pH and water predictions to gas-phase NH3 and HNO3 concentrations. Our sensitivity analysis indicated that even though NH3 and HNO3 were present at very low concentrations in the eastern North Atlantic during the campaign, PM1 pH calculations can still be sensitive to NH3 concentrations. Specifically, NH3 was needed to constrain the pH of populations of PM1 that had low mass concentrations of NH4+ and non-volatile cations (NVCs). We next assumed that gas-phase NH3 and HNO3 concentrations during the campaign were 0.15 and 0.09 µg m−3, respectively, based on previous measurements conducted in the eastern North Atlantic. Using the assumption that PM1 were internally mixed (i.e., bulk PM1), we determined that PM1 pH ranged from 0.3–8.6, with a mean pH of 5.0 ± 2.3. The pH depended on both Hair+ and Wi. Hair+ was controlled primarily by the NVCs/SO42− molar ratio, while Wi was controlled by the SO42− mass concentration and RH. Changes in pH with altitude were driven primarily by changes in SO42−. Since aerosols in marine atmospheres are rarely internally mixed, the scenario where non-sea salt species and sea-salt species were present in two separate aerosol modes in the PM1 (i.e., completely externally mixed) was also considered. Smaller pH values were predicted for the aerosol mode comprised only of non-sea salt species compared to the bulk PM1 (difference of around 1 unit on average). This was due to the exclusion of sea-salt species (especially hygroscopic alkaline NVCs) in this aerosol mode, which led to increases in Hair+ values and decreases in Wi values. This result demonstrated that assumptions of aerosol mixing states can impact aerosol pH predictions substantially, which will have important implications for evaluating the nature and magnitude of pH-dependent atmospheric processes that occur in the marine boundary layer.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Cooperative Effects Associated with High Electrolyte Concentrations in Driving the Conversion of CO2 to C2H4 on Copper

Compared to a conventional electrolyte concentration of 1 M HCOOK, the use of a highly concentrated 7.1 M HCOOK electrolyte increases the Faradaic efficiency (FE) ratio of C2H4/CO from 2.2 +- 0.3 to 18.3 +- 4.8 at -1.08 V vs. reversible hydrogen electrode (RHE) on a Cu gas-diffusion electrode. Based on electrochemical analysis and ab initio molecular dynamics (AIMD) simulation, the identity and concentration of the cation and anion play more important roles in controlling the CO2R reaction pathway than the bulk CO2 solubility and the bulk pH of electrolytes. In situ attenuated reflectance surface enhanced infrared absorption spectroscopy (ATR-SEIRAS) suggests that, unlike 1 M HCOOK, the *CO-bridge-binding mode on Cu is dominant in 7.1 M HCOOK electrolyte, which potentially results in less CO release and higher yield of C2H4. This study demonstrates that although we can tailor the electrolyte composition to shift product selectivity, the factors that control the product selectivity are numerous and cannot be distilled down into one correlated property-reactivity relationship.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1981

Gaseous constituents in the plume from eruptions of Mount St. Helens

Measurements in the stratosphere of gaseous constituents in the plume of Mount St. Helens were obtained during five flights of the NASA U-2 aircraft between 19 May and 17 June 1980. Mixing ratios from gas chromatographic measurements on samples acquired about 24 hours after the initial eruption show considerable enhancement over nonvolcanic concentrations for sulfur dioxide (more than 1000 times), methyl chloride (about 10 times), and carbon disulfide (more than 3 times). The mixing ratio of carbonyl sulfide was comparable to nonvolcanic mixing ratios although 3 days later it was enhanced two to three times. Ion chromatography measurements on water-soluble constituents are also reported. Very large concentrations of chloride, nitrate, and sulfate ions were measured, implying large mixing ratios for the water-soluble gaseous constituents from which the anions are derived. Measurements of radon-222 present in the plume are also reported.

Inn, E. C. Y.↗

DOE OSTI2023

A Systematic Investigation of the Effects of Standard-Sample Concentration Mismatch during Fe Isotope Measurement by MC-ICP-MS

Advances in multi-collector inductively coupled plasma-mass spectrometry (MC-ICP-MS) have led to the widespread use of iron (Fe) isotopes to elucidate the (bio)geochemical history of a range of environments. To generate Fe isotope ratio measurements, standard-sample bracketing (SSB) is commonly used to correct for instrumental mass bias inherent to MC-ICP-MS. However, SSB is only accurate when sample and isotope standard Fe concentrations match, in addition to the bulk solution matrix. When the Fe concentrations differ, Fe isotope ratio measurement results may be inaccurate, a phenomenon known as the "self-induced matrix effect." Here, this study systematically characterised the self-induced matrix effect for dry plasma Fe isotope ratio measurements on three MC-ICP-MS instruments and three introduction systems. Our extensive dataset indicates that: (1) the degree of mass bias is consistent regardless of MC-ICP-MS front-end design, (2) the degree of mass bias becomes less reproducible as the concentration difference between the sample and bracketing standard increases, and (3) this applies to both pure Fe solutions and solutions from geological materials. This study reinforces the requirement to match bracketing standard and sample concentrations within 10% and provides a correction method for that fall beyond the recommended concentration range to subsequently allow for proper concentration matching during SSB.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1993

Fuel-rich catalytic combustion of a high density fuel

Fuel-rich catalytic combustion (ER is greater than 4) of the high density fuel exo-tetrahydrocyclopentadiene (JP-10) was studied over the equivalence ratio range 5.0 to 7.6, which yielded combustion temperatures of 1220 to 1120 K. The process produced soot-free gaseous products similar to those obtained with iso-octane and jet-A in previous studies. The measured combustion temperature agreed well with that calculated assuming soot was not a combustion product. The process raised the effective hydrogen/carbon (H/C) ratio from 1.6 to over 2.0, thus significantly improving the combustion properties of the fuel. At an equivalence ratio near 5.0, about 80 percent of the initial fuel carbon was in light gaseous products and about 20 percent in larger condensable molecules. Fuel-rich catalytic combustion has now been studied for three fuels with H/C ratios of 2.25 (iso-octane), 1.92 (jet-A), and 1.6 (JP-10). A comparison of the product distribution of these fuels shows that, in general, the measured concentrations of the combustion products were monotonic functions of the H/C ratio with the exception of hydrogen and ethylene. In these cases, data for JP-10 fell between iso-octane and jet-A rather than beyond jet-A. It is suggested that the ring cross-linking structure of JP-10 may be responsible for this behavior. All the fuels studied showed that the largest amounts of small hydrocarbon molecules and the smallest amounts of large condensable molecules occurred at the lower equivalence ratios. This corresponds to the highest combustion temperatures used in these studies. Although higher temperatures may improve this mix, the temperature is limited. First, the life of the present catalyst would be greatly shortened when operated at temperatures of 1300 K or greater. Second, fuel-rich catalytic combustion does not produce soot because the combustion temperatures used in the experiments were well below the threshold temperature (1350 K) for the formation of soot. Increasing the temperature above this value would remove the soot-free nature of the process. Since all the fuels studied show a similar breakdown of the primary fuel into smaller molecular combustion products, this technique can be applied to all hydrocarbon fuels.

Brabbs, Theodore A.↗

DOE OSTI2024

Effective Corrosion-Resistant Single-Atom Alloy Catalyst on HfO 2 -Passivated BiVO 4 Photoanode for Durable (≈800 h) Solar Water Oxidation

Green hydrogen (H 2 ) production from solar water splitting necessitates photoelectrodes with superior photoelectrochemical (PEC) activity and durability. However, surface defects and photocorrosion instability—especially at high potentials—limit PEC performance and stability. Herein, the prototypical bismuth vanadate (BiVO 4 ) photoanode is used to demonstrate a holistic approach to improve photocurrent density and long-term stability. In this approach, high surface-area nanostructuring of BiVO 4 is combined with barium (Ba) doping with semi-crystalline hafnium oxide (HfO 2 ) surface passivation and single-atom nickel platinum (NiPt) catalysts. The introduction of Ba 2+ ions into BiVO 4 increases the concentration of conductive V 4+ ions or the ratio of V 4+ ions to oxygen vacancies, avoiding V 5+ dissolution during water oxidation. The semi-crystalline HfO 2 , which serves as a passivation layer, prevents BiVO 4 photocorrosion by suppressing harmful chemical reactions when holes are transferred to the electrolyte. The synergistic use of isolated single-atom and Ni-Pt coordination improves charge transfer at the photoanode/electrolyte interface, leading to enhanced PEC kinetics and stability. As a result, a photoelectrode is demonstrated with ≈6.5 mA cm -2 at 1.23 V versus a reversible hydrogen electrode (RHE) and continuous operation for 800 h with a negligible degradation rate. This work provides a promising approach to improve photoanodes for PEC H 2 production.

08 HYDROGEN↗

DOE OSTI2023

Nanostructure Scaling in Semi-Dilute Triblock Copolymer Gels

Here, there is a considerable body of work that describes the scaling of diblock copolymer micelle dimensions in dilute and semi-dilute solution based upon block degrees of polymerization and copolymer concentration. However, there is a lack of analogous information for semi-dilute ABA triblock copolymer gels, which consist of ABA triblock copolymer dissolved in midblock-selective (B-selective) solvent. The present study uses small angle X-ray scattering to extract micelle dimensions for numerous triblock copolymer gels that vary in copolymer identity (and hence block lengths) and copolymer concentration, as well as gels that contain various ratios of two unique triblock copolymers. Analysis of micelle structural data subsequently translates to universal scaling expressions for the micelle core radius – r A ≈ N A 0.53 N B -0.14 $\phi$ ABA 0.16 where N A and N B are the endblock and midblock degrees of polymerization, respectively, and $\phi$ ABA is the volume fraction of triblock copolymer in the gel – and for the intermicelle spacing – l AA ≈ N A 0.09 N B 0.29 $\phi$ ABA -0.35 . Each scaling expression describes the full collection of experimental data very well. Additionally, these scaling expressions are partially in line with expectations from semi-dilute diblock copolymer solution theory.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Using groundwater noble gas measurements to confirm paleorecharge hypotheses at Pahute Mesa, Nevada National Security Site, Nevada, USA

Pahute Mesa (Nevada, USA) was the site of 85 underground nuclear tests between 1965 and 1992 whose residual radio-chemical inventory poses a contaminant threat to local groundwater resources. To assess the fate and transport of these radionuclides in groundwater, several geochemical studies, including this one, have been conducted to understand long-term groundwater flow patterns at, and downgradient of, Pahute Mesa. Groundwater samples from the Pahute Mesa area at the Nevada National Security Site were analyzed for noble gases ( 3 He/ 4 He isotopic ratio and He, Ne, Kr, Ar and Xe concentrations) to infer groundwater recharge temperatures and provide additional evidence in support of groundwater flow patterns and the presence of late-pluvial Pleistocene groundwater. These data confirm recent findings (based on groundwater geochemistry and isotope compositions) that most recharge in the area occurred under temperature conditions much cooler than are found today, except near major drainages where ephemeral run of continues to recharge shallow groundwater. These noble gas data indicate that noble gas recharge temperatures and terrigenic He components have been reset where groundwater has flowed upward over barriers formed by caldera margins, or near the regional discharge area (Oasis Valley) where shallow groundwater has interacted with shallow soil gas. This evidence from groundwater noble gas measurements, in combination with other isotopic and geochemical studies, supports the current understanding of the unusual hydrogeology and recharge history of Pahute Mesa.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Experimental study of mechanistic factors influencing solvent-driven fractional crystallization of calcium sulfate

To advance dimethyl ether-driven fractional crystallization (DME-FC), a more sustainable method of water treatment and mineral recovery, a range of chemical equilibria were measured. These include varying concentrations of miscible organic solvents (MOS) used to experimentally measure the solvent-induced solid-liquid equilibrium (SLE) of calcium sulfate (CaSO 4 ) in water. Seven MOS, including dimethyl ether (DME), acetonitrile (MeCN), 1,4-dioxane, tetrahydrofuran (THF), acetone, ethanol, and diethylamine, were screened to establish trends associated with molecular volume, functional groups, and physical properties. The effect of MOS on CaSO 4 removal differed at concentrations <0.15 mol fraction MOS; MOS with greater molecular volume (THF, 1,4-dioxane, and diethylamine) induced greater CaSO 4 precipitation on a per mole basis. The solvent-induced SLE for all MOS converged between 0.15 and 0.2 mol fraction MOS, reaching a CaSO 4 concentration consistent with a water to MOS hydration ratio of 5:1 to 6:1, which may correspond to the solvent generating a solution-based pseudo-clathrate structure with continuity within the solution. Finally, solution pseudo-clathrate structures provide a mechanistic basis for DME-FC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗