Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPARATIVE EVALUATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2026

Citric Acid Functionalized Natural Fibers to Enhance Thermal Stability and Moisture Resistance in Polylactic Acid Composites

Cellulosic fibers can impart many unique benefits into composite applications, such as reduced weight or structural reinforcement; however, these materials also increase hygroscopicity and decrease thermal stability, restricting broader applications. The present work adapted an experimental process for functionalizing the cellulose surface using citric acid (CA) for three fibers: a 100% cellulose bleached soft Kraft pulp (e.g., creafill) and two natural fibers with similar composition but different fiber morphology, flax fiber and banana fiber. The process uses CA with a sodium hypophosphite (SHP) catalyst to chemically functionalize fiber surfaces, and the reaction mechanism was investigated through Fourier Transform Infrared Spectroscopy (FTIR), which suggested a grafting mechanism rather than a surface-based crosslinking between neighboring sites. Functionalized fibers were compounded into polylactic acid (PLA) at 20 wt.% to better understand how this functionalization might impact critical performance properties like thermal stability, crystallization, thermal mechanical properties, and water uptake of these composites. The study demonstrated varying levels of efficacy for the functionalization of cellulosic fibers with CA/SHP and the fiber with the most open microstructure, e.g., banana fiber, exhibited the largest change in its properties with a 38% reduction in water uptake compared to untreated banana fiber composites. Parallel evaluation of the functionalization process for different fibers demonstrates the importance of fiber morphology on surface modification and can enable their use in composites by demonstrating the efficacy of this potentially low-cost, low-toxicity method for reducing hygroscopicity and improving thermal stability.

citric acid↗
DOE OSTI2020

Optimal Equilibrium Selection of Price-Maker Agents in Performance-Based Regulation Market

This paper analyzes the oligopolistic equilibrium of multiple price-maker agents in performance-based regulation (PBR) markets. In these markets, there are price-maker agents representing some frequency regulation (FR) providers and a number of independent price-taker FR providers. An equilibrium problem with equilibrium constraints (EPEC) model is employed in this paper to study the equilibria of a PBR market in the presence of price-maker agents and pricetaker FR providers. Due to the incorporation of the FR providers' dynamics, the proposed model is reformulated as a mixed-integer linear programming (MILP) problem over innovative mathematical techniques. An optimal equilibrium point is also selected for the market, where none of the agents is unique deviator and the dynamic performance of power system is improved simultaneously. The effectiveness of proposed optimal equilibrium point is evaluated in the numerical results section by comparing the outputs with conventional optimal dispatches of the FR providers.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Star Formation Histories from Spectral Energy Distributions and Color–magnitude Diagrams Agree: Evidence for Synchronized Star Formation in Local Volume Dwarf Galaxies over the Past 3 Gyr

Star formation histories (SFHs) reveal physical processes that influence how galaxies form their stellar mass. We compare the SFHs of a sample of 36 nearby (D ≲ 4 Mpc) dwarf galaxies from the ACS Nearby Galaxy Survey Treasury (ANGST), inferred from the color–magnitude diagrams (CMDs) of individually resolved stars in these galaxies, with those reconstructed by broadband spectral energy distribution (SED) fitting using the dense basis SED-fitting code. When comparing individual SFHs, we introduce metrics for evaluating SFH reconstruction techniques. For both the SED and CMD methods, the median normalized SFH of galaxies in the sample shows a period of quiescence at lookback times of 3–6 Gyr followed by rejuvenated star formation over the past 3 Gyr that remains active until the present day. To determine if these represent special epochs of star formation in the D <4 Mpc portion of the Local Volume, we break this ANGST dwarf galaxy sample into subsets based on specific star formation rate and spatial location. Modulo offsets between the methods of about 1 Gyr, all subsets show significant decreases and increases in their median normalized SFHs at the same epochs, and the majority of the individual galaxy SFHs are consistent with these trends. These results motivate further study of potential synchronized star formation quiescence and rejuvenation in the Local Volume as well as development of a hybrid method of SFH reconstruction that combines CMDs and SEDs, which have complementary systematics.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Simulation of radon-222 with the GEOS-Chem global model: Emissions, seasonality, and convective transport

Radon-222 (222Rn) is a short-lived radioactive gas naturally emitted from land surface, and has long been used to assess convective transport in atmospheric models. In this study, we simulate 222Rn using the GEOS-Chem chemical transport model with aims to improve our understanding of 222Rn emissions and surface concentration seasonality, and to characterize convective transport associated with two Goddard Earth Observing System (GEOS) meteorological products, MERRA and GEOS-FP. We evaluate four available 222Rn emission scenarios by comparing model results with surface observations at 51 global surface sites. The default emission scenario in GEOS-Chem yields a moderate agreement with global surface observations (< 70% data within a factor of 2) and a large underestimate of wintertime surface 222Rn concentrations at Northern Hemisphere mid- and high-latitudes due to an oversimplified formulation of 222Rn emission fluxes (1 atom cm-2 s-1 over land with a reduction by a factor of 3 under freezing conditions). We compose a new global 222Rn emission scenario based on Zhang et al. (2011) and show its potential to improve simulated surface 222Rn concentrations and seasonality. The regional components of this emission scenario include spatially and temporally varying emission fluxes derived from previous measurements of soil radium content and soil exhalation models, which are key factors to 222Rn emission flux rates. However, large model underestimates of surface 222Rn concentrations still exist in Asia, suggesting unusually high regional 222Rn emissions. We propose a conservative up-scaling factor of 1.2 for 222Rn emission fluxes in China, as also constrained by the observed deposition fluxes of 210Pb (decay daughter of 222Rn). With this modification, the model shows better agreement with the observations in Europe and North America (>80% data within a factor of 2), and reasonable agreement in Asia (close to 70%). Further constraints on 222Rn emissions would require additional observations of surface 222Rn concentrations and emission fluxes in central U.S., Canada, Africa, and Asia. We also compare and assess convective transport in model simulations driven by MERRA and GEOS-FP using observed 222Rn vertical profiles during northern mid-latitude summertime and from two short-term airborne campaigns. While the simulations with both GEOS products are able to capture the observed vertical gradient of 222Rn concentrations in the lower troposphere (0-4 km), neither correctly represents the level of convective detrainment, resulting in biases in the middle and upper troposphere. Compared to GEOS-FP, MERRA leads to stronger convective transport of 222Rn, which is partially compensated by its weaker large-scale vertical advection, resulting in similar global vertical distributions of 222Rn concentrations between the two simulations.

Zhang, Bo↗
DOE OSTI2024

Evaluation of Global Fire Simulations in CMIP6 Earth System Models

Fire is the primary form of terrestrial ecosystem disturbance on a global scale and an important Earth system process. Most Earth system models (ESMs) have incorporated fire modeling, with 19 of them submitting model outputs of fire-related variables to the Coupled Model Intercomparison Project Phase 6 (CMIP6). This study provides the first comprehensive evaluation of CMIP6 historical fire simulations by comparing them with multiple satellite-based products and charcoal-based historical reconstructions. Our results show that most CMIP6 models simulate the present-day global burned area and fire carbon emissions within the range of satellite-based products. They also capture the major features of observed spatial patterns and seasonal cycles, the relationship of fires with precipitation and population density, and the influence of the El Niño–Southern Oscillation (ENSO) on the interannual variability of tropical fires. Regional fire carbon emissions simulated by the CMIP6 models from 1850 to 2010 generally align with the charcoal-based reconstructions, although there are regional mismatches, such as in southern South America and eastern temperate North America prior to the 1910s and in temperate North America, eastern boreal North America, Europe, and boreal Asia since the 1980s. The CMIP6 simulations have addressed three critical issues identified in CMIP5: (1) the simulated global burned area being less than half of that of the observations, (2) the failure to reproduce the high burned area fraction observed in Africa, and (3) the weak fire seasonal variability. Furthermore, the CMIP6 models exhibit improved accuracy in capturing the observed relationship between fires and both climatic and socioeconomic drivers and better align with the historical long-term trends indicated by charcoal-based reconstructions in most regions worldwide. However, the CMIP6 models still fail to reproduce the decline in global burned area and fire carbon emissions observed over the past 2 decades, mainly attributed to an underestimation of anthropogenic fire suppression, and the spring peak in fires in the Northern Hemisphere midlatitudes, mainly due to an underestimation of crop fires. In addition, the model underestimates the fire sensitivity to wet–dry conditions, indicating the need to improve fuel wet-ness estimation. Based on these findings, we present specific guidance for fire scheme development and suggest a postprocessing methodology for using CMIP6 multi-model outputs to generate reliable fire projection products.

Wildfire, Earth system models↗
DOE OSTI2026

Public water supply infrastructure extensification and diversification in surface waters is insufficient to meet future demands in Texas

The data were developed to evaluate the capacity of existing and potential new surface water supply infrastructure to meet projected public water demands across districts in Texas under multiple future socioeconomic and climate scenarios. The database integrates hydrologic, water quality, infrastructure, energy, cost, demographic, and demand-projection information for candidate surface water supply locations. Candidate sites include stream reaches, waterbodies, reservoir surplus locations, and potential new reservoir sites. Water availability is characterized using historical and projected flow conditions, while site suitability is evaluated using five indicators: Water Availability Index (WAI), Water Quality Index (WQI), Energy Requirement Index (ERI), Water Treatment Cost (WTC), and Water Infrastructure Cost (WIC). The datasets include statewide candidate-site information, district-level demand projections under Shared Socioeconomic Pathways (SSPs), runoff-based allocation constraints, climate-stress metrics, and optimization outputs evaluating alternative infrastructure planning strategies. Optimization results compare Business-as-Usual (BAU) and All Surface Water (AllSW) demand-management approaches under both scaled and fixed cost-cap strategies. Associated validation datasets provide district-level feasibility assessments, infrastructure selection outcomes, cost-cap utilization, demand satisfaction metrics, and constraint diagnostics. Additional datasets quantify projected changes in storage and flow conditions as well as water availability stress for both existing and newly selected intake locations under the SSP5 scenario for mid-century and late-century climate conditions. Together, these datasets support assessment of the extent to which surface-water infrastructure expansion and diversification strategies can satisfy future public water demands while accounting for hydrologic, economic, and planning constraints across Texas. Dataset(s) Description Dataset_preoptimization.xlsx Comprehensive pre-optimization dataset containing candidate water-supply sites and associated hydrologic, water-quality, infrastructure, climate, demographic, runoff, and demand-projection variables used as inputs to the optimization analyses. Includes variable descriptions and the full statewide candidate-site database. District_level_site_selection.zip - Compressed archive containing all SSP-specific district-level optimization result files MESIO_ssp1_results.xlsx District-level site selection results for SSP1 (MESIO). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. MESID_ssp2_results.xlsx District-level site selection results for SSP2 (MESID). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. LCMRD_ssp3_results.xlsx District-level site selection results for SSP3 (LCMRD). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. IRDev-Low_ssp4l_results.xlsx District-level site selection results for SSP4-Low (IRDev-Low). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. IRDev-High_ssp4h_results.xlsx District-level site selection results for SSP4-High (IRDev-High). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. RSIM_ssp5_results.xlsx District-level site selection results for SSP5 (RSIM). Includes variable descriptions, BAU and AllSW site-selection results under scaled and fixed cost strategies, and district-level validation diagnostics. tx_hydrological_stress.xlsx Hydrological stress dataset for existing and newly selected intake locations. Includes projected mid-century and late-century changes, gain/loss classifications, planning strategy information, and accompanying variable descriptions. Also includes water-stress metrics derived from historical and projected low-flow conditions.

Okoye, Perpetua I. (ORCID:0000000215545033)↗
DOE OSTI2020

Accelerated Aging and Evaluation of Hose-In-Hose Transfer Lines in the Hanford Waste Transfer System - 20312

Nonmetallic materials are used in the United States Department of Energy's Hanford Site Tank Farm waste transfer system. These materials include the inner primary hoses in the hose-in-hose transfer lines (HIHTLs), Garlock{sup R} gaskets, ethylene propylene diene monomer (EPDM) O-rings, and other nonmetallic materials. These nonmetallic materials are exposed to β and γ radiation, caustic solutions as well as high temperature and pressure stressors. How the nonmetallic components react to each of these stressors individually has been well established. However, simultaneous exposure of these stressors has not been evaluated and is of great concern to Hanford Site engineers. Florida International University's Applied Research Center engineers worked closely with key Hanford's Washington River Protection Solutions personnel to develop an experimental test plan that determines how these nonmetallic components react to various simultaneous stressor exposures. In this paper, research on the experimental testing of the hose-in-hose transfer lines used in the Hanford tank farm waste transfer system under simultaneous stressor exposures is presented. The stressor exposure experiments consisted of various combinations of simultaneous stressor exposure of caustic solution, high temperature and high pressure stressors. Research efforts focused on evaluating the aging behavior of EPDM by exposing samples of HIHTLs as well as EPDM dog bone shaped specimens to a 25% NaOH solution at (38 deg. C), operating (54 deg. C) and design temperatures (77 deg. C) for 6 months and 12 months. In addition, HIHTL and the EPDM dog-bone specimens were exposed to only hot water at 77 deg. C for a duration of one year. The mechanical and material properties of the samples were characterized and compared with those of the unexposed samples (baseline). Evaluations included burst pressure tests of the EPDM hose-in-hose transfer lines and material tensile strength test of EPDM dog-bone coupons. Both the tensile strength of the EPDM material dog bones and the burst pressure of the HIHTLs significantly decreased with the increasing temperature and increasing exposure time. When compared with the baseline samples, the burst pressure decreased by 28.75% for the sample aged at 77 deg. C after 12 months, in comparison to sample aged at 38 deg. C and 54 deg. C which had about 1.34% and 5.70% loss in burst pressures, respectively, after 12-month exposure. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

The HOSTS Survey for Exozodiacal Dust: Observational Results from the Complete Survey

The Large Binocular Telescope Interferometer (LBTI) enables nulling interferometric observations across the N band (8 to 13 μm) to suppress a star’s bright light and probe for faint circumstellar emission. We present and statistically analyze the results from the LBTI/Hunt for Observable Signatures of Terrestrial Systems survey for exozodiacal dust. By comparing our measurements to model predictions based on the solar zodiacal dust in the N band, we estimate a 1σ median sensitivity of 23 zodis times the solar system dust surface density in its habitable zone (HZ; 23 zodis) for early-type stars and 48 zodis for Sun-like stars, where 1 zodi is the surface density of HZ dust in the solar system. Of the 38 stars observed, 10 show significant excess. A clear correlation of our detections with the presence of cold dust in the systems was found, but none with the stellar spectral type or age. The majority of Sun-like stars have relatively low HZ dust levels (best-fit median: 3 zodis, 1σ upper limit: 9 zodis, 95% confidence: 27 zodis based on our N band measurements), while ~20% are significantly more dusty. The solar system’s HZ dust content is consistent with being typical. Our median HZ dust level would not be a major limitation to the direct imaging search for Earth-like exoplanets, but more precise constraints are still required, in particular to evaluate the impact of exozodiacal dust for the spectroscopic characterization of imaged exo-Earth candidates.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Real-Time Evolution and Deployment of Neuromorphic Computing at The Edge

Extremely low power neuromorphic systems are well-suited for deployment to the edge for many applications. In many use cases of neuromorphic computing for control, a spiking neural network is trained off-line using a simulation and then deployed to a neuromorphic system at the edge, where it will operate without ongoing training or learning. However, it may be desirable to continue training or learning at the edge to refine or adapt to the real-world system. In this work, we propose an approach for performing real-time evolutionary optimization for spiking neural networks for neuromorphic deployment at the edge. In particular, we propose a combination of simulation and real-world evaluations, along with feedback from the real-world environment, to train spiking neural networks for continuous deployment to the edge. We show that the real-time evolution at the edge approach achieves comparable performance to an evolution approach that requires constant evaluation in the realworld environment.

Schuman, Catherine↗
DOE OSTI2021

Development, Implementation, and Verification of Partially-Ionized Collisional Multifluid Plasma Models in Drekar

We consider the development of multifluid models for partially ionized multispecies plasmas. The models are composed of a standard set of five-moment fluid equations for each species plus a description of electromagnetics. The most general model considered utilizes a full set of fluid equations for each charge state of each atomic species, plus a set of fluid equations for electrons. The fluid equations are coupled through source terms describing electromagnetic coupling, ionization, recombination, charge exchange, and elastic scattering collisions in the low-density coronal limit. The form of each of these source terms is described in detail, and references for required rate coefficients are identified for a diverse range of atomic species. Initial efforts have been made to extend these models to incorporate some higher-density collisional effects, including ionization potential depression and three- body recombination. Some reductions of the general multifluid model are considered. First, a reduced multifluid model is derived which averages over all of the charge states (including neutrals) of each atomic species in the general multifluid model. The resulting model maintains full consistency with the general multifluid model from which it is derived by leveraging a quasi-steady-state collisional ionization equilibrium assumption to recover the ionization fractions required to make use of the general collision models. Further reductions are briefly considered to derive certain components of a single-fluid magnetohydrodynamics (MHD) model. In this case, a generalized Ohm's law is obtained, and the standard MHD resistivity is expressed in terms of the collisional models used in the general multifluid model. A number of numerical considerations required to obtain robust implementations of these multifluid models are discussed. First, an algebraic flux correction (AFC) stabilization approach for a continuous Galerkin finite element discretization of the multifluid system is described in which the characteristic speeds used in the stabilization of the fluid systems are synchronized across all species in the model. It is demonstrated that this synchronization is crucial in order to obtain a robust discretization of the multifluid system. Additionally, several different formulations are considered for describing the electromagnetics portion of the multifluid system using nodal continuous Galerkin finite element discretizations. The formulations considered include a parabolic divergence cleaning method and an implicit projection method for the traditional curl formulation of Maxwell's equations, a purely- hyperbolic potential-based formulation of Maxwell's equations, and a mixed hyperbolic-elliptic potential-based formulation of Maxwell's equations. Some advantages and disadvantages of each formulation are explored to compare solution robustness and the ease of use of each formulation. Numerical results are presented to demonstrate the accuracy and robustness of various components of our implementation. Analytic solutions for a spatially homogeneous damped plasma oscillation are derived in order to verify the implementation of the source terms for electromagnetic coupling and elastic collisions between fluid species. Ionization balance as a function of electron temperature is evaluated for several atomic species of interest by comparing to steady-state calculations using various sets of ionization and recombination rate coefficients. Several test problems in one and two spatial dimensions are used to demonstrate the accuracy and robustness of the discretization and stabilization approach for the fluid components of the multifluid system. This includes standard test problems for electrostatic and electromagnetic shock tubes in the two-fluid and ideal shock-MHD limits, a cylindrical diocotron instability, and the GEM challenge magnetic reconnection problem. A one-dimensional simplified prototype of an argon gas puff configuration as deployed on Sandia's Z-machine is used as a demonstration to exercise the full range of capabilities associated with the general multifluid model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Total-Ionizing-Dose Effects on Long-term Data Retention Characteristics of Commercial 3-D NAND Memories

This article evaluates the data retention characteristics of irradiated multi-level cell (MLC) 3-D NAND flash memories. We irradiate the memory chips by a Co-60 gamma-ray source for up to 50 krad(Si) and then write a random data pattern on the irradiated chip to find its retention characteristics. The experimental results show that the data retention property of the irradiated chips is significantly degraded compared to the un-irradiated ones. We evaluate two independent strategies to improve the data retention characteristics of the irradiated chips. Furthermore, the first method involves high-temperature annealing of the irradiated chip while the second method suggests pre-programming the memory modules before deploying them in radiation-prone environments.

3-D NAND flash↗
DOE OSTI2021

FPGA-based HPC accelerators: An evaluation on performance and energy efficiency

Hardware specialization is a promising direction for the future of digital computing. Reconfigurable technologies enable hardware specialization with modest non-recurring engineering cost, but their performance and energy efficiency compared to state-of-the-art processor architectures remain an open question. In this article, we use FPGAs to evaluate the benefits of building specialized hardware for numerical kernels found in scientific applications. In order to properly evaluate performance, we not only compare Intel Arria 10 and Xilinx U280 performance against Intel Xeon, Intel Xeon Phi, and NVIDIA V100 GPUs, but we also extend the Empirical Roofline Toolkit (ERT) to FPGAs in order to assess our results in terms of the Roofline model. We show design optimization and tuning techniques for peak FPGA performance at reasonable hardware usage and power consumption. As FPGA peak performance is known to be far less than that of a GPU, we also benchmark the energy efficiency of each platform for the scientific kernels comparing against microbenchmark and technological limits. Results show that while FPGAs struggle to compete in absolute terms with GPUs on memory- and compute-intensive kernels, they require far less power and can deliver nearly the same energy efficiency.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Power System Resilience Evaluation Framework and Metric Review: Preprint

Power system resilience is an emerging hot topic in recent years to study the increasing threats of extreme events such as natural disasters, severe weather, and cyberattacks. Although many research works have been done to define, model, and quantify resilience from different aspects, the lack of universally accepted resilience metrics and evaluation methods makes it difficult to assess and compare resilience across different power systems like what is typically done in power system reliability studies. In this paper, we first review the definitions of resilience and summarized two core concepts shared by most literature. On top of that, we conduct a thorough review of resilience metrics and develop a new framework to assess power system resilience from two perspectives, i.e., pre-event estimation and post-event evaluation, to capture system resilience performance in both general and specific fashions. Existing resilience metrics are summarized and categorized using the proposed framework, where recommendations are also proposed to capture core concepts of resilience.

power system resilience↗
DOE OSTI2021

Towards an Agent-Based Blackboard System for Reactor Design Optimization

The field of reactor design is rich with opportunities for applications of computational optimization algorithms; these applications can range from preliminary core design to reactor shuffling patterns. Many of these schemes rely on sets of previously generated solutions (sometimes referred to as “generations”) to inform future decisions. While it is important to build upon prior knowledge, this process requires a full generation of solutions to be formed before future solutions can be examined. Rather than relying on a generational scheme to perform an optimization, we propose using an agent-based approach in conjunction with a blackboard framework for performing reactor design optimizations. Utilizing an agent-based approach allows agents to perform tasks independently, while retaining the ability to build off of previous solutions. We develop an agent-based blackboard system (ABBS) for determining the Pareto front (PF) in sodium fast reactor design optimization problems and compared this with the Non-Dominated Sorting Genetic Algorithm II (NSGA-II). Our goal is to evaluate the viability of the ABBS in producing a PF that is comparable with the NSGA-II algorithm. The design space consists of the fuel height, fuel smear, and plutonium fraction in the core, and we seek to minimize the reactivity swing and plutonium mass, while maximizing the burnup. The diversity, coverage, and spread of the PFs generated by the two methods are examined, and the ABBS is able to converge to the same PF as the NSGA-II algorithm. These results show that the ABBS is able to find optimal designs that are similar to those found by the NSGA-II algorithm. We conclude our study by applying the ABBS to the design of a sodium-cooled fast reactor to dispose of weapons-grade plutonium. The ABBS finds a core design that can burn upwards of 17.5 kg of weapons-grade plutonium per year and degrade an additional 195 kg of weapons-grade plutonium per year into non-weapons-grade material.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Assessing the Consistency of Estimated Ground Cover Fractions between the BLM AIM Method and Optical Remote Sensing Method

Since 2012, Argonne National Laboratory (Argonne) has supported the Bureau of Land Management (BLM) in developing remote sensing methodologies for long-term environmental monitoring of Palo Verde Mesa in eastern Riverside County, California, including methods for: detailed mapping of ephemeral streams, estimating fractional cover of desert-land surface components (e.g., trees, shrubs, litters, and bare ground), evaluating erosion risk or land stability, and characterizing vegetation alliances using spatial structure and geostatistical approaches. These studies showed the promise of remote sensing for monitoring changes in desert landscapes by providing information that would be difficult to obtain through field surveys. During this time the BLM has also worked to establish long-term monitoring protocols and compiled field-observation data collected using standardized protocols from the Assessment, Inventory, and Monitoring (AIM) strategy. The AIM data can be compared to data derived from remote sensing methods to evaluate their relative operational utility in monitoring landscape change. If ground cover estimated using remotely sensed imagery is comparable to AIM ground cover estimates, then remote sensing can be used to monitor whether any land cover change in desert landscapes may be related to solar energy development. Therefore, the goal of this study was to determine the consistency in ground cover estimates between AIM data and those derived from publicly- available remotely sensed imagery, such as that available through the U.S. Department of Agriculture, National Agricultural Imagery Program (NAIP), to examine feasibility of a remote sensing method for complementing AIM monitoring. Based on the image analysis in this study, we also provide recommendations for how small unmanned aerial system (sUAS) data may be used to complement BLM’s AIM data and NAIP imagery for future vegetation monitoring. The ground cover types we originally planned to investigate were trees, shrubs, and bare ground. However, the small sample size and a limited range of cover fraction of trees and shrubs in the AIM dataset (e.g., 33 samples with a maximum shrub cover of 18%, 14 samples with a maximum tree cover of 17%) did not allow for performing a meaningful evaluation for the remote sensing approach. Therefore, we conducted the study focusing on bare ground, foliar, and rock cover, all of which are indicators reported in the AIM remote sensing dataset.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

The effect of neutron irradiation on conventional and nanocrystalline nickel: NSUF Work Package UA-22PN080501 Milestone M3UA-22PN0805012 (Final Report)

Even though nanocrystalline materials (20-100 nm) present an unprecedented potential, scientific knowledge related to the effect of neutron irradiation on the mechanical properties and microstructure is still scarce. Most of the past studies were conducted using ion irradiation which may not have the same effect as neutron irradiation because of the smaller irradiation volume and the higher dose rate. To reach a firm conclusion on the potential of nanocrystalline materials for nuclear reactor applications, extensive study of model metals with different stacking fault energy (SFE) is required to elucidate their behavior in radiation environments. Nanocrystalline copper and nickel are typically chosen because they are commonly used as model FCC metals in studies of radiation effects. Nickel is an FCC metal with a high stacking-fault energy (~125 mJ/m 2 ) compared to copper (~45 mJ/m 2 ). Hence, microcrystalline and nanocrystalline nickel samples were irradiated in the INL’s Advanced Test Reactor (ATR), as a part of FY08 North Carolina State University NSUF Irradiation Experiment# 96 to evaluate the irradiation behavior of these materials. The objective of this FY20 NSUF project# 19122 is to perform PIE (at PNNL NSUF facility) on previously ATR-neutron irradiated (1.2 and 2.6 dpa; 80-89°C) nanocrystalline and microcrystalline nickel samples to investigate the changes in mechanical properties and microstructures and evaluate whether nanocrystalline nickel is relatively more radiation resistant compared to conventional microcrystalline nickel. To perform PIE at PNNL, sixteen neutron irradiated specimens (microcrystalline and nanocrystalline) were transferred from the NSUF Nuclear Fuels and Materials Library at INL. Experimental techniques such as SEM/EBSD, XRD, TEM, Vickers microhardness and tensile testing were employed to characterize the effect of neutron irradiation on the microstructure and mechanical properties of nanocrystalline nickel and compared them with corresponding characteristics of microcrystalline nickel.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Assessment of the ParFlow–CLM CONUS 1.0 integrated hydrologic model: evaluation of hyper-resolution water balance components across the contiguous United States

Abstract. Recent advancements in computational efficiency and Earth system modeling have awarded hydrologists with increasingly high-resolution models of terrestrial hydrology, which are paramount to understanding and predicting complex fluxes of moisture and energy. Continental-scale hydrologic simulations are, in particular, of interest to the hydrologic community for numerous societal, scientific, and operational benefits. The coupled hydrology–land surface model ParFlow–CLM configured over the continental United States (PFCONUS) has been employed in previous literature to study scale-dependent connections between water table depth, topography, recharge, and evapotranspiration, as well as to explore impacts of anthropogenic aquifer depletion to the water and energy balance. These studies have allowed for an unprecedented process-based understanding of the continental water cycle at high resolution. Here, we provide the most comprehensive evaluation of PFCONUS version 1.0 (PFCONUSv1) performance to date by comparing numerous modeled water balance components with thousands of in situ observations and several remote sensing products and using a range of statistical performance metrics for evaluation. PFCONUSv1 comparisons with these datasets are a promising indicator of model fidelity and ability to reproduce the continental-scale water balance at high resolution. Areas for improvement are identified, such as a positive streamflow bias at gauges in the eastern Great Plains, a shallow water table bias over many areas of the model domain, and low bias in seasonal total water storage amplitude, especially for the Ohio, Missouri, and Arkansas River basins. We discuss several potential sources for model bias and suggest that minimizing error in topographic processing and meteorological forcing would considerably improve model performance. Results here provide a benchmark and guidance for further PFCONUS model development, and they highlight the importance of concurrently evaluating all hydrologic components and fluxes to provide a multivariate, holistic validation of the complete modeled water balance.

O'Neill, Mary M. F. (ORCID:0000000221455165)↗