Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BRITTLENESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

A Comparative Analysis on Microstructure and Fracture Mechanism of X100 Pipeline Steel CGHAZ Between Laser Welding and Arc Welding

The objective of this study is to compare and contrast the differences in microstructure and fracture mechanism between CGHAZ of laser welding and submerged arc welding in X100 pipeline steel. The single-pass welding thermal simulation test of laser welding and submerged arc welding was carried out in MMS-200 thermal simulation test machine using self-made fixtures. The results indicated that the microstructure of laser welding CGHAZ and submerged arc welding CGHAZ was lath martensite and granular bainite, respectively. The impact energy of laser welding CGHAZ was 27 J, and the fracture mode was ductile fracture; the impact energy of submerged arc welding CGHAZ was 7.7 J, and the fracture mode was brittle fracture. The nucleation and propagation mechanism of cracks in different welding modes was established. Microcracks nucleated at the position of dislocation accumulation and remained austenite suppressed crack nucleation in laser welding CGHAZ. The nucleation site was at the M–A constituents in submerged arc welding CGHAZ. The main crack of laser welding CGHAZ was formed by one or a small number of microcracks. The main crack in submerged arc welding CGHAZ was formed by a large number of microcracks. The difference between crack nucleation and propagation mechanism is the reason why the impact energy of laser welding CGHAZ is higher than of submerged arc welding CGHAZ.

36 MATERIALS SCIENCE↗

Laser Additive Manufacturing Process Development for Bismuth Telluride Thermoelectric Material

Thermoelectric generators have strong potential for aerospace and aircraft applications. However, traditional manufacturing methods for thermoelectric devices severely limit device adaptability and consequently marketability. Laser powder bed fusion is an additive manufacturing method which shows promising potential for producing thermoelectric devices. Thermoelectric materials pose unique challenges compared to metals because of low thermal conductivity, brittle fracture characteristics, and irregular powder particle morphologies. Herein, we communicate processing procedures to fabricate thermoelectric parts of Bi 2 Te 3 through laser powder bed fusion. In this study, we identify the successful combination of key process parameters—laser power, scan speed, hatch distance, and powder layer thickness—to achieve high-quality parts in terms of density and physical properties, and we demonstrate the impact of process parameter variation on built part quality. While it cannot exclusively determine part quality, the volumetric energy density is a useful guide in deciding process parameters for thermoelectric materials, and the optimal value is between 9 and 11 J/mm 3 for Bi 2 Te 3 . We demonstrate successful fabrication of different freeform geometries of Bi 2 Te 3 powders. The results suggest it is possible to extend this method more broadly to other semiconductor materials, including thermoelectric power generation materials applicable for space applications.

36 MATERIALS SCIENCE↗

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗

Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys

To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.

36 MATERIALS SCIENCE↗

Diffusion Barrier Selection from Refractory Metals (Zr, Mo and Nb) via Interdiffusion Investigation for U-Mo RERTR Fuel Alloy

U-Mo alloys are being developed as low enrichment monolithic fuel under the Reduced Enrichment for Research and Test Reactor (RERTR) Program. Diffusional interactions between the U-Mo fuel alloy and Al-alloy cladding within the monolithic fuel plate construct necessitate incorporation of a barrier layer. Fundamentally, a diffusion barrier candidate must have good thermal conductivity, high melting point, minimal metallurgical interaction, and good irradiation performance. Refractory metals, Zr, Mo, and Nb are considered based on their physical properties, and the diffusion behavior must be carefully examined first with U-Mo fuel alloy. Solid-to-solid U-10wt.%Mo vs. Mo, Zr, or Nb diffusion couples were assembled and annealed at 600, 700, 800, 900 and 1000 degrees C for various times. The interdiffusion microstructures and chemical composition were examined via scanning electron microscopy and electron probe microanalysis, respectively. For all three systems, the growth rate of interdiffusion zone were calculated at 1000, 900 and 800 degrees C under the assumption of parabolic growth, and calculated for lower temperature of 700, 600 and 500 degrees C according to Arrhenius relationship. The growth rate was determined to be about 10 3 times slower for Zr, 10 5 times slower for Mo and 10 6 times slower for Nb, than the growth rates reported for the interaction between the U-Mo fuel alloy and pure Al or Al-Si cladding alloys. Zr, however was selected as the barrier metal due to a concern for thermo- mechanical behavior of UMo/Nb interface observed from diffusion couples, and for ductile-to-brittle transition of Mo near room temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

Phase equilibria and microstructure evolution in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C

The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.

energy dispersive spectrometry↗

Interface-Driven Plasticity in Metal–Ceramic Nanolayered Composites: Direct Validation of Multiscale Deformation Modeling via In Situ Indentation in TEM

Here, we present in situ indentation in a transmission electron microscope on Al-TiN multilayers with individual layer thicknesses of 50 nm and 2.7 nm to explore the effect of length scales on the plastic co-deformability of a metal and a ceramic. At 50 nm, plasticity was confined to the Al layers with brittle fracture in the TiN layers. At 5 nm and below, cracking in TiN was suppressed with co-deformation evident in both layers. The in situ transmission electron microscopy (TEM) straining results demonstrate a profound size effect in enhancing plastic co-deformability in nanoscale metal-ceramic multilayers, as well as direct validation of ex situ and 3-D elastic–plastic deformation models.

36 MATERIALS SCIENCE↗

In-Situ Grain Resolved Stress Characterization During Damage Initiation in Cu-10%W Alloy

The evolution of stress during damage initiation and accumulation in a two-phase alloy consisting of a ductile copper (Cu) matrix with a randomly dispersed brittle tungsten (W) phase was studied using multiple non-destructive experimental probes. Neutron diffraction measurements were performed to examine the macroscopic strain partitioning between the two phases during a uniaxial tension test. The same material was then examined with high-energy x-ray diffraction microscopy (HEDM) and micro-computed tomography (μ-CT) measurements to monitor micromechanical field evolution. The neutron diffraction data indicated a redistribution of load between the Cu and W phases as deformation proceeds. Therefore, using HEDM to monitor individual grain micromechanical behavior, an increase followed by decrease in hydrostatic stress and a similar stress triaxiality behavior were found to occur in a subset of W grains. These same W grains were found to be in close proximity to voids observed via tomography at later stages of deformation. From these observations, we conclude that high stress triaxiality development in the W particles leads to decohesion of the interface between the Cu and W phases. The debonded regions eventually grew and coalesced with neighboring voids leading to material failure.

36 MATERIALS SCIENCE↗

Joining AA7099 to Ni-Cr-Mo Steel Using Single Pass Friction Stir Dovetailing and AA6061 Butter Layer

A novel single pass friction stir dovetailing (FSD) was developed to join thick plate AA7099 to Ni-Cr-Mo steel in a lap configuration through the use of an AA6061 butter layer. The butter layer approach can be shown to significantly reduce interfacial failures by inhibiting the formation of brittle Fe–Al intermetallic compounds (IMCs) which are typically formed during conventional friction stir welding (FSW) of AA7099 directly to steel. This study evaluates the strength and microstructural evolution of the aluminum/steel joint interface between single pass FSD of AA7099/AA6061(butter)/steel fabricated using three different FSD tool configurations. The butter layer was achieved by placement of a free-floating strip of AA6061 within the dovetail groove that was pre-machined in the steel substrate. Friction stir welding was then used to simultaneously join the thick plate AA7099, the AA6061 strip and the AA7099 in a single weld pass. To optimize the joining process, three different pin geometries (full thread, half smooth/half thread, no thread) were evaluated; it was demonstrated that the half smooth/half thread tool produced the strongest weld joint due to the absence of a Zn rich layer at the Al/steel interface. The efficacy of this unique processing technique was tested using lap shear tensile testing as well as high resolution transmission electron microscopy (TEM). A discussion of the new FSD technique, joint configurations, and process parameters are provided along with joint microstructural analyses and mechanical performance.

Olszta, Matthew J.↗

Adversarial Ensemble Modeling of Multi-modal Mechanical Properties for Iron-Based Alloys

Mechanical properties of alloys are controlled by their microstructure; and microstructure evolution is controlled by internal and external stressors. Chemical complexity during the alloy processing may result in heterogeneity and observation of multimodal performance patterns. Thus, to ensure the desired performance of stressed components it is important to understand the origin and mechanisms of such behavior. Adversarial ensemble modeling was introduced here to explain multimodal mechanical properties of the iron-based alloys. The modeling results showed that the areas of a single mechanism predominance were contiguous across the alloy compositions clustered by similarity, with sharp and persistent boundaries separating the single-mechanism domains. The marginal compositions resulted in increased competition between the adversarial models but only led to the multimodal behavior when the competing models diverged. Transparency of the clustering method allowed explicit interpretation of the chemistries leading to such competition. The adversarial ensemble was interpreted through transition from ductile to brittle microstructure.

36 MATERIALS SCIENCE↗

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗

Characterization of Fe-6Si Soft Magnetic Alloy Produced by Laser-Directed Energy Deposition Additive Manufacturing

Abstract Commercial electrical steels, Fe-Si alloys with < 4 wt.% Si, are inexpensive and efficient materials for electrical power conversion. Further efficiency improvements require increasing the silicon concentration to 6 wt.%, at which point the material becomes brittle and difficult to form by conventional rolling and sheet fabrication methods. Additive manufacturing stands to overcome challenges with commercial manufacturing techniques by leveraging near-net-shape fabrication. The wide array of process conditions provides additive manufacturing with increased flexibility, enabling control over the microstructure and mechanical properties. This work explores the microstructures and magnetic properties of ring-shaped Fe-Si alloys produced using concentric and cross-hatch tool paths on a laser-directed energy deposition additive manufacturing system. Concentric-built samples exhibit elongated grain structures while cross-hatch-built samples comprise lower aspect ratio grain structures. Thermal finite element analysis simulations model the stress conditions produced by the different scan path geometries. Microhardness measurements probe the mechanical properties as a function of anneal temperature, providing a qualitative understanding of the intergranular defect density. Soft magnetic properties measured under quasistatic and AC conditions show frequency- and microstructure-dependent coercivity and permeability. Finally, analysis of the core loss quantifies how the build strategies and thermal treatments influence efficiency in electrical power conversion applications. Understanding the influences of scan path geometry and thermal treatment provides a pathway towards application of additively manufactured soft magnetic materials.

Adamczyk, Jesse M.↗

Ion Implantation-Induced Plastic Phenomena in Metallic Alloys

Ion implantation is widely used for doping semiconductors or electroceramic materials and probing material behaviors in extreme radiation environments. However, implanted ions can induce compressive stresses into the host material, which can induce plasticity and mesoscopic deformation. However, these phenomena have almost exclusively been observed in brittle ionic and/or covalently bonded materials. Here, in this study, we present transmission electron microscopy observations of unusual implantation-induced plasticity in two metallic alloys. First, Fe 2+ ions induce dislocation plasticity below the implanted layer in a model Fe-P alloy. Next, He+ ions form pressurized cavities which activate the fcc-to-hcp strain-induced martensitic transformation in Alloy 625. In both cases, the plasticity can be explained by a combination of implanted ions being incorporated into the lattice and the creation of irradiation defects. These findings have significant implications for mechanical testing of ion-implanted layers, while also opening pathways for using ion implantation to tune stress distributions in metallic alloys.

36 MATERIALS SCIENCE↗

A New Method for Polishing Laminated Dissimilar Metals

Here, this paper presents a novel method for preparing metallographic samples of laminated dissimilar metals, specifically a layered structure of zirconium (Zr), vanadium (V), and tungsten (W), which pose a challenge due to their differing crystal structures and hardness levels. The work was motivated by the need to develop a cladding for tungsten targets in spallation neutron sources, where a zirconium face is applied over an interlayer of either vanadium or titanium to prevent the formation of brittle intermetallic compounds such as ZrW 2 . Traditional polishing techniques prove inadequate because each constituent metal requires a different polishing approach based on its unique material properties. The methodology outlined includes a sequential process involving conductive epoxy mounting, successive grinding and polishing with specific abrasives, and a final chemical-mechanical polish using a colloidal silica-based solution. Optical microscopy confirmed that this multi-step process successfully produced scratch-free surfaces and minimized surface relief across the different metal interfaces. Although developed for refractory metals, this approach shows promise for other layered structures comprised of transition metals, offering a meticulous yet effective technique for high-quality metallographic sample preparation.

Newberry, Daniel [Oak Ridge National Laboratory (O↗

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗

Dynamic Tensile Experimental Techniques for Geomaterials: A Comprehensive Review

Here, this review article is dedicated to the Dynamic Behavior of Materials Technical Division for celebrating the 75th anniversary of the Society for Experimental Mechanics (SEM). Understanding dynamic behavior of geomaterials is critical for analyzing and solving engineering problems of various applications related to underground explosions, seismic, airblast, and penetration events. Determining the dynamic tensile response of geomaterials has been a great challenge in experiments due to the nature of relatively low tensile strength and high brittleness. Various experimental approaches have been made in the past century, especially in the most recent half century, to understand the dynamic behavior of geomaterials in tension. In this review paper, we summarized the dynamic tensile experimental techniques for geomaterials that have been developed. The major dynamic tensile experimental techniques include dynamic direct tension, dynamic split tension, and spall tension. All three of the experimental techniques are based on Hopkinson or split Hopkinson (also known as Kolsky) bar techniques and principles. Finally, uniqueness and limitations for each experimental technique are also discussed.

36 MATERIALS SCIENCE↗

Dynamic Tensile Response of a Fe–49Co–2V Alloy at Various Strain Rates and Temperatures

Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s -1 and temperatures from - 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.

36 MATERIALS SCIENCE↗