Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vibration analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Test versus analysis: A discussion of methods

Some techniques for comparing structural vibration data determined from test and analysis are discussed. Orthogonality is a general category of one group, correlation is a second, synthesis is a third and matrix improvement is a fourth. Advantages and short-comings of the methods are explored with suggestions as to how they can complement one another. The purpose for comparing vibration data from test and analysis for a given structure is to find out whether each is representing the dynamic properties of the structure in the same way. Specifically, whether: mode shapes are alike; the frequencies of the modes are alike; modes appear in the same frequency sequence; and if they are not alike, how to judge which to believe.

Butler, T. G.↗

Vibration detection of component operability

In order to prevent catastrophic failure and eliminate unnecessary periodic maintenance in the Space Shuttle Orbiter dynamic components, instrumentation for detecting incipient failure in these components is required. This study investigated the utilization of vibrational phenomena as one of the principal physical parameters on which to base the design of this instrumentation. Baseline vibration data was collected from three aircraft type fans and two aircraft type pumps over a frequency range from a few Hertz to greater than 300 kHz. The baseline data included spectrum analysis of the vibration and detected carrier signals, as well as several non-spectrum parameters. Several defects were introduced into the five test items, and all defects were detected by at least one of the parameters with a margin of at least 2:1 over the worst case baseline.

Baird, B.↗

Status of integrated multidisciplinary rotorcraft optimization research at the Langley Research Center

This paper describes a joint NASA/Army research activity at the Langley Research Center to develop optimization procedures aimed at improving the rotor blade design process by integrating appropriate disciplines and accounting for important interactions among the disciplines. The activity is being guided by a Steering Committee made up of key NASA and Army researchers and managers. The paper describes the optimization formulation in terms of the objective function, design variables, and constraints. The analysis aspects are discussed, and the interdisciplinary interactions are defined in terms of the information that must be transferred among disciplinary analyses as well as the trade-offs between disciplines in determining the details of the design. At this writing, some significant progress has been made. Results given in the paper represent accomplishments in rotor aerodynamic performance optimization for minimum horsepower, rotor dynamic optimization for vibration reduction, approximate analysis of frequencies and mode shapes, rotor structural optimization for minimum weight, and integrated aerodynamic load/dynamics optimization for minimum vibration and weight.

Mantay, Wayne R.↗

FOURIER TRANSFORM EMISSION SPECTROSCOPY OF THE A {sup 2}{Pi}-X {sup 2}{Sigma}{sup +} (RED) SYSTEM OF {sup 13}C{sup 14}N

Emission spectra of the A {sup 2{Pi}}-X {sup 2}{Sigma}{sup +} transition (red system) of {sup 13}C{sup 14}N have been measured in the 4000-15,000 cm{sup -1} region using the Fourier transform spectrometer associated with the McMath-Pierce Solar Telescope of the National Solar Observatory. The {sup 13}C{sup 14}N free radical was produced in microwave discharge of a mixture of {sup 13}CH{sub 4} and {sup 14}N{sub 2}. Rotational analysis of 22 vibrational bands involving vibrational levels up to v' = 8 and v'' = 5 of the excited and ground states has been obtained and much improved spectroscopic constants have been determined. An experimental line list and calculated term values are provided. The results of the present analysis are useful for the identification of {sup 13}C{sup 14}N lines in late-type stars in the red and near-infrared spectral regions.

79 ASTRONOMY AND ASTROPHYSICS↗

Rigid-flexible coupling multi-body dynamics modeling of a semi-submersible floating offshore wind turbine

A 14-degree-of-freedom (14-DOF) flexible multibody dynamics model is developed and verified for a semi-submersible floating offshore wind turbine (FOWT). The model considers the coupled dynamics of the platform, tower, nacelle, blades, and mooring subjected to external wind and wave loads. The platform is simplified as a rigid body connected to the seabed by the mooring system. The tower and blade are modeled as flexible cantilever beams. The energy method is used to derive the governing equations of motion, where the kinetic energy, potential energy, and work done by external wind-wave forces are all deduced in a global coordinate system. The 5-MW baseline semi-submersible FOWT is used to verify the derived model against the results simulated from FAST developed by the US National Renewable Energy Laboratory (NREL) at two scenarios: free decay state and different wind-wave load cases. Results show that the established FOWT model can well reflect the vibration characteristics of FAST model. The application of the model to the control of platform pitch with a tuned mass damper is studied. Furthermore, the simplified model could provide a low-order method for the structural dynamics analysis and advanced vibration control design for the multi-body components of the semi-submersible FOWT in the future.

17 WIND ENERGY↗

Vibration and buckling of general periodic lattice structures

A method is presented for vibration and buckling analysis of arbitrary lattice structures having repetitive geometry in any combination of coordinate directions. The approach is based on exact member theory for representing the stiffness of an individual member subject to axial load, and in the case of vibration, undergoing harmonic oscillation. The method is an extension of previous work that was limited to specific geometries. The resulting eigenvalue problem is of the size associated with the repeating element of the structure. A computer program has been developed incorporating the theory and results are given for vibration of rectangular platforms and a large antenna structure having rotational symmetry. Buckling and vibration results for cable-stiffened rings are also given.

Anderson, M. S.↗

Ground shake test of the UH-60A helicopter airframe and comparison with NASTRAN finite element model predictions

Sikorsky Aircraft, together with the other major helicopter airframe manufacturers, is engaged in a study to improve the use of finite element analysis to predict the dynamic behavior of helicopter airframes, under a rotorcraft structural dynamics program called DAMVIBS (Design Analysis Methods for VIBrationS), sponsored by the NASA-Langley. The test plan and test results are presented for a shake test of the UH-60A BLACK HAWK helicopter. A comparison is also presented of test results with results obtained from analysis using a NASTRAN finite element model.

Howland, G. R.↗

Future Issues and Approaches to Health Monitoring and Failure Prevention for Oil-Free Gas Turbines

Recent technology advances in foil air bearings, high temperature solid lubricants and computer based modeling has enabled the development of small Oil-Free gas turbines. These turbomachines are currently commercialized as small (<100 kW) microturbine generators and larger machines are being developed. Based upon these successes and the high potential payoffs offered by Oil-Free systems, NASA, industry, and other government entities are anticipating Oil-Free gas turbine propulsion systems to proliferate future markets. Since an Oil-Free engine has no oil system, traditional approaches to health monitoring and diagnostics, such as chip detection, oil analysis, and possibly vibration signature analyses (e.g., ball pass frequency) will be unavailable. As such, new approaches will need to be considered. These could include shaft orbit analyses, foil bearing temperature measurements, embedded wear sensors and start-up/coast down speed analysis. In addition, novel, as yet undeveloped techniques may emerge based upon concurrent developments in MEMS technology. This paper introduces Oil-Free technology, reviews the current state of the art and potential for future turbomachinery applications and discusses possible approaches to health monitoring, diagnostics and failure prevention.

DellaCorte, Christopher↗

Improved Technique for Finding Vibration Parameters

Filtering and sample manipulation reduce noise effects. Analysis technique improves extraction of vibrational frequencies and damping rates from measurements of vibrations of complicated structure. Structural vibrations measured by accelerometers. Outputs digitized at frequency high enough to cover all modes of interest. Use of method on set of vibrational measurements from Space Shuttle, raised level of coherence from previous values below 50 percent to values between 90 and 99 percent

Andrew, L. V.↗

Quantification of Gear Tooth Damage by Optimal Tracking of Vibration Signatures

This paper presents a technique for quantifying the wear or damage of gear teeth in a transmission system. The procedure developed in this study can be applied as a part of either an onboard machine health-monitoring system or a health diagnostic system used during regular maintenance. As the developed methodology is based on analysis of gearbox vibration under normal operating conditions, no shutdown or special modification of operating parameters is required during the diagnostic process. The process of quantifying the wear or damage of gear teeth requires a set of measured vibration data and a model of the gear mesh dynamics. An optimization problem is formulated to determine the profile of a time-varying mesh stiffness parameter for which the model output approximates the measured data. The resulting stiffness profile is then related to the level of gear tooth wear or damage. The procedure was applied to a data set generated artificially and to another obtained experimentally from a spiral bevel gear test rig. The results demonstrate the utility of the procedure as part of an overall health-monitoring system.

Choy, F. K.↗

Probabilistic structural analysis methods and applications

An advanced algorithm for simulating the probabilistic distribution of structural responses due to statistical uncertainties in loads, geometry, material properties, and boundary conditions is reported. The method effectively combines an advanced algorithm for calculating probability levels for multivariate problems (fast probability integration) together with a general-purpose finite-element code for stress, vibration, and buckling analysis. Application is made to a space propulsion system turbine blade for which the geometry and material properties are treated as random variables.

Cruse, T. A.↗

Analysis of Methods of Investigation of the Vibration–Rotation Spectrum of Monomers and Dimers of Sulphur Hexafluoride Isotopes

The stability of the system of sulphur hexafluoride dimer SF{sub 6} under the action of external laser radiation has been estimated using ab initio quantum-chemical calculations of the vibration–rotation spectrum of SF{sub 6} monomers as well as homo- and heterodimers. It is noted that for simple CO molecule as an example, the most widely used method of calculations based on the Hessian matrix approach cannot serve as a reliable instrument in quantitative calculations of some molecular systems. As a potential analog, we have tested the algorithm for obtaining the vibration–rotation spectrum based on molecular dynamics data.

74 ATOMIC AND MOLECULAR PHYSICS↗

Rotational branch analysis of the excitation of the fundamental vibrational modes of CO2 by slow electron collisions

At 2 eV, the simultaneous rotational-vibrational cross sections for the fundamental modes are found to be well described by the Born formula with just long-range interactions. However, this result is not obtained for pure vibrational excitation (Q branch) in the Raman-active Fermi diads. At 3.8 eV, the infrared-active v2 and v3 cross sections agree with a previous theory incorporating resonant and direct scattering coherently. Measurements on the Raman-active v1 mode indicate that theories need to account for the Fermi resonance.

Antoni, TH.↗

Ground Vibration Test Planning and Pre-Test Analysis for the X-33 Vehicle

This paper describes the results of the modal test planning and the pre-test analysis for the X-33 vehicle. The pre-test analysis included the selection of the target modes, selection of the sensor and shaker locations and the development of an accurate Test Analysis Model (TAM). For target mode selection, four techniques were considered, one based on the Modal Cost technique, one based on Balanced Singular Value technique, a technique known as the Root Sum Squared (RSS) method, and a Modal Kinetic Energy (MKE) approach. For selecting sensor locations, four techniques were also considered; one based on the Weighted Average Kinetic Energy (WAKE), one based on Guyan Reduction (GR), one emphasizing engineering judgment, and one based on an optimum sensor selection technique using Genetic Algorithm (GA) search technique combined with a criteria based on Hankel Singular Values (HSV's). For selecting shaker locations, four techniques were also considered; one based on the Weighted Average Driving Point Residue (WADPR), one based on engineering judgment and accessibility considerations, a frequency response method, and an optimum shaker location selection based on a GA search technique combined with a criteria based on HSV's. To evaluate the effectiveness of the proposed sensor and shaker locations for exciting the target modes, extensive numerical simulations were performed. Multivariate Mode Indicator Function (MMIF) was used to evaluate the effectiveness of each sensor & shaker set with respect to modal parameter identification. Several TAM reduction techniques were considered including, Guyan, IRS, Modal, and Hybrid. Based on a pre-test cross-orthogonality checks using various reduction techniques, a Hybrid TAM reduction technique was selected and was used for all three vehicle fuel level configurations.

Bedrossian, Herand↗