Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “total correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Correlated Migration Invokes Higher Na + ‐Ion Conductivity in NaSICON‐Type Solid Electrolytes

Abstract Na super ion conductor (NaSICON), Na 1+ n Zr 2 Si n P 3– n O 12 is considered one of the most promising solid electrolytes; however, the underlying mechanism governing ion transport is still not fully understood. Here, the existence of a previously unreported Na5 site in monoclinic Na 3 Zr 2 Si 2 PO 12 is unveiled. It is revealed that Na + ‐ions tend to migrate in a correlated mechanism, as suggested by a much lower energy barrier compared to the single‐ion migration barrier. Furthermore, computational work uncovers the origin of the improved conductivity in the NaSICON structure, that is, the enhanced correlated migration induced by increasing the Na + ‐ion concentration. Systematic impedance studies on doped NaSICON materials bolster this finding. Significant improvements in both the bulk and total ion conductivity (e.g., σ bulk = 4.0 mS cm −1 , σ total = 2.4 mS cm −1 at 25 °C) are achieved by increasing the Na content from 3.0 to 3.30–3.55 mol formula unit −1 . These improvements stem from the enhanced correlated migration invoked by the increased Coulombic repulsions when more Na + ‐ions populate the structure rather than solely from the increased mobile ion carrier concentration. The studies also verify a strategy to enhance ion conductivity, namely, pushing the cations into high energy sites to therefore lower the energy barrier for cation migration.

Zhang, Zhizhen↗
NASA NTRS1990

An analysis of the viscous flow through a compact radial turbine by the average passage approach

A steady, three-dimensional viscous average passage computer code is used to analyze the flow through a compact radial turbine rotor. The code models the flow as spatially periodic from blade passage to blade passage. Results from the code using varying computational models are compared with each other and with experimental data. These results include blade surface velocities and pressures, exit vorticity and entropy contour plots, shroud pressures, and spanwise exit total temperature, total pressure, and swirl distributions. The three computational models used are inviscid, viscous with no blade clearance, and viscous with blade clearance. It is found that modeling viscous effects improves correlation with experimental data, while modeling hub and tip clearances further improves some comparisons. Experimental results such as a local maximum of exit swirl, reduced exit total pressures at the walls, and exit total temperature magnitudes are explained by interpretation of the flow physics and computed secondary flows. Trends in the computed blade loading diagrams are similarly explained.

Heidmann, James D.↗
NASA NTRS1990

An analysis of the viscous flow through a compact radial turbine by the average passage approach

A steady, three-dimensional viscous average passage computer code is used to analyze the flow through a compact radial turbine rotor. The code models the flow as spatially periodic from blade passage to blade passage. Results from the code using varying computational models are compared with each other and with experimental data. These results include blade surface velocities and pressures, exit vorticity and entropy contour plots, shroud pressures, and spanwise exit total temperature, total pressure, and swirl distributions. The three computational models used are inviscid, viscous with no blade clearance, and viscous with blade clearance. It is found that modeling viscous effects improves correlation with experimental data, while modeling hub and tip clearances further improves some comparisons. Experimental results such as a local maximum of exit swirl, reduced exit total pressures at the walls, and exit total temperature magnitudes are explained by interpretation of the flow physics and computed secondary flows. Trends in the computed blade loading diagrams are similarly explained.

Heidmann, James D.↗
DOE OSTI2026

A case study on the use of carbon sticky tabs for microbeam uranium isotope measurement with an emphasis on understanding the influence of subtle variations in substrate composition

In this paper we integrate laser induced breakdown spectroscopy (LIBS), large geometry secondary ion mass spectrometry (LG-SIMS), laser ablation—multi collector—inductively coupled plasma—mass spectrometry (LA-MC-ICP-MS), and trace elemental compositions obtained by bulk digestion from a suite of commercially available carbon sticky tabs to determine if subtle variations in the tab’s composition can be tied to shifts in the observed uranium isotopic composition of the IRMM-2020 standard relative to its ‘true’ value. The results suggest that, although clear differences exist in the relative abundances of carbon and hydrogen across the various carbon sticky tabs examined, as well as differences in their trace elemental and total uranium concentrations, these differences do not appear to influence the LG-SIMS or LA-MC-ICP-MS uranium isotope ratio measurements, or the appearance of the uranium mass spectrum scans. Instead, the quality (i.e., precision and accuracy) of the LG-SIMS and LA-MC-ICP-MS results are directly proportional to the observed signal intensity at the time of analysis. For the LG-SIMS measurements, there does appear to be a direct correlation between 235U1H hydride formation rates and vacuum conditions within the instrument’s analytical chamber. Furthermore, none of the carbon sticky tabs examined by LG-SIMS displayed evidence of elevated background uranium content. While a preliminary correlation was observed between the uranium isotope background signal during LA-MC-ICP-MS and the total uranium concentrations determined by isotope dilution, none of the tabs displayed a high enough analytical background to affect the isotope ratio measurements.

Zirakparvar, Alex [ORNL] (ORCID:0000000337797730)↗
DOE OSTI2020

Extrinsic Absorption Pathways in Vanadium-Doped SiC Measured Using a Total Internal Reflection Geometry

Vanadium-doped SiC is under study for high-power photoconductive switches and is receiving increased attention as a potential material system for quantum computing, as the V can act as a quantum emitter at telecom wavelengths. Knowledge of the defect-mediated electronic transition pathways from sub-bandgap illumination in this material with low absorption and multi-photon and multi-path transition probability is important in optimizing quantum efficiency. Herein, the optical transitions of vanadium-doped SiC for two polytypes as a function of dopant concentration using a total internal reflection (TIR) geometry are examined. Furthermore, normalized quantum efficiency is reported and correlated with both dopant concentrations (V, N, B, and Al) measured by secondary ion mass spectroscopy (SIMS) and absorption measurements. Although both polytypes respond well to 532 nm light, efficiency at longer wavelengths does not correlate 1:1 with absorption coefficient and strongly depends on the polytype and net background co-dopant concentration. This has important implications for efficient excitation of both carriers for optoelectronics and for the use of V as a quantum emitter.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microbial abundances and carbon use under ambient temperature or experimental warming in a southern boreal peatland

Abstract Organic peat soils occupy relatively little of the global land surface area but store vast amounts of soil carbon in northern latitudes where climate is warming at a rapid pace. Warming may result in strong positive feedbacks of carbon loss and global climate change driven by microbial processes if warming alters the balance between primary productivity and decomposition. To elucidate effects of warming on the microbial communities mediating peat carbon dynamics, we explored the abundance of broad microbial groups and their source of carbon (i.e. old carbon versus more recently fixed photosynthate) using microbial lipid analysis (δ 13 C PLFA) of peat samples under ambient temperatures and before/after initiation of experimental peat warming (+ 2.25, + 4.5, + 6.75, and + 9 °C). This analysis occurred over a profile to 2 m depth in an undrained, ombrotrophic peat bog in northern Minnesota. We found that the total microbial biomass and individual indicator lipid abundances were stratified by depth and strongly correlated to temperature under ambient conditions. However, under experimental warming, statistically significant effects of temperature on the microbial community were sporadic and inconsistent. For example, 3 months after experimental warming the relative abundance of Gram-negative bacterial indicators across depth combined and > 50 cm depth and Gram-positive bacterial indicators at 20–50 cm depth showed significant positive relationships to temperature. At that same timepoint, however, the relative abundance of Actinobacterial indicators across depth showed a significant negative relationship to temperature. After 10 months of experimental warming, the relative abundance of fungal biomarkers was positively related to temperature in all depths combined, and the absolute abundance of anaerobic bacteria declined with increasing temperature in the 20–50 cm depth interval. The lack of observed response in the broader microbial community may suggest that at least initially, microbial community structure with peat depth in these peatlands is driven more by bulk density and soil water content than temperature. Alternatively, the lack of broad microbial community response may simply represent a lag period, with more change to come in the future. The long-term trajectory of microbial response to warming in this ecosystem then could either be direct, after this initial lag time, or indirect through other physical or biogeochemical changes in the peat profile. These initial results provide an important baseline against which to measure long-term microbial community and carbon-cycling responses to warming and elevated CO 2 .

Felice, Mark↗
DOE OSTI2019

Characterizing the Influence of Fracture Density on Network Scale Transport

The topology of natural fracture networks is inherently linked to the structure of the fluid velocity field and transport therein. Here we study the impact of network density on flow and transport behaviors. We stochastically generate fracture networks of varying density and simulate flow and transport with a discrete fracture network model, which fully resolves network topology at the fracture scale. We study conservative solute trajectories with Lagrangian particle tracking and find that as fracture density decreases, solute channelization to large local fractures increases, thereby reducing plume spreading. Furthermore, in sparse networks mean particle travel distance increases and local network features, such as velocity zones where flow is counter to the primary pressure gradient, become increasingly important for transport. As the network density increases, network statistics homogenize and such local features have a reduced impact. We quantify local topological influence on transport behavior with an effective tortuosity parameter, which measures the ratio of total advective distance to linear distance at the fracture scale; large tortuosity values are correlated to slow-velocity regions. Additionally, these large tortuosity, slow-velocity regions delay downstream transport and enhance tailing on particle breakthrough curves. Finally, we predict transport with an upscaled, Bernoulli spatial Markov random walk model and parameterize local topological influences with a novel tortuosity parameter. Furthermore, Bernoulli model predictions improve when sampling from a tortuosity distribution, as opposed to a fixed value as has previously been done, suggesting that local network topological features must be carefully considered in upscaled modeling efforts of fracture network systems.

58 GEOSCIENCES↗
DOE OSTI2025

Requirements on the gain calibration for LiteBIRD polarisation data with blind component separation

The detection of primordial B modes of the cosmic microwave background (CMB) could provide information about the early stages of the Universe's evolution. The faintness of this signal requires exquisite calibration accuracy and control of instrumental systematic effects which otherwise could bias the measurements. In this work, we study the impact of an imperfect relative polarisation gain calibration on the recovered value of the tensor-to-scalar ratio r for the LiteBIRD experiment, through the application of the blind Needlet Internal Linear Combination (NILC) foreground-cleaning method. We derive requirements on the relative calibration accuracy of the overall polarisation gain (Δg ν ) for each LiteBIRD frequency channel. Our results show that minimum variance techniques, as NILC, are less sensitive to systematic gain calibration uncertainties compared to a parametric approach, if the latter is not equipped with a proper modelling of these instrumental effects. In this study, the most stringent requirements are found in the channels where the CMB signal is relatively brighter, with the tightest constraints at 166 GHz (Δg ν ≈ 0.16%). This differs from the outcome of an analogous analysis performed with a parametric method, where the tightest requirements are obtained for the foreground-dominated channels. Gain calibration uncertainties, corresponding to the derived requirements, are then simultaneously propagated into all frequency channels. By doing so, we find that the overall impact on estimated r is lower than the total gain systematic budget for LiteBIRD approximately by a factor 5, due to the correlations of the impacts of gain calibration uncertainties in different frequency channels. In order to decouple the systematic effect from the specific choice of the model, we derive the requirements assuming constant spectral parameters for the foreground emission. To assess the robustness of the obtained results against more realistic scenarios, we repeat the analysis assuming sky models of intermediate and high complexity. In these further cases, we adopt an optimised NILC pipeline, called the Multi-Clustering NILC (MC-NILC). We find that the impact of gain calibration uncertainties on r is lower than the LiteBIRD gain systematics budget for the intermediate-complexity sky model. For the high-complexity case, instead, it would be necessary to tighten the requirements by a factor 1.8.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Local distortion driven magnetic phase switching in pyrochlore Yb 2 ( Ti 1 - x Sn x ) 2 O 7

While it is commonly accepted that the disorder induced by magnetic ion doping in quantum magnets usually generates a rugged free-energy landscape resulting in slow or glassy spin dynamics, the disorder/distortion effects associated with nonmagnetic ion sites doping are still illusive. Here, using AC susceptibility measurements, we show that the mixture of Sn/Ti on the nonmagnetic ion sites of pyrochlore Yb 2 ⁢(Ti 1-x⁢ Sn x ) 2⁢ O 7 induces an antiferromagnetic ground state despite both parent compounds, Yb 2 ⁢Ti 2 ⁢O 7 and Yb 2 ⁢Sn 2⁢ O 7 , order ferromagnetically. Local structure studies through neutron total scattering reveals the local distortion in the nonmagnetic ion sites and its strong correlation with the magnetic phase switching. Further, our study demonstrates the local distortion as induced by the nonmagnetic ion site mixture could be a new path to achieve magnetic phase switching, which has been traditionally obtained by external stimuli such as temperature, magnetic field, pressure, strain, light, etc.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Geographic patterns and determinants of antibiotic resistomes in coastal sediments across complex ecological gradients

Coastal areas are highly influenced by terrestrial runoffs and anthropogenic disturbances, commonly leading to ecological gradients from bay, nearshore, to offshore areas. Although the occurrence and distribution of sediment antibiotic resistome are explored in various coastal environments, little information is available regarding geographic patterns and determinants of coastal sediment antibiotic resistomes across ecological gradients at the regional scale. Here, using high-throughput quantitative PCR, we investigated the geographic patterns of 285 antibiotic resistance genes (ARGs) in coastal sediments across a ~ 200 km scale in the East China Sea. Sediment bacterial communities and physicochemical properties were characterized to identify the determinants of sediments antibiotic resistome. Higher richness and abundance of ARGs were detected in the bay samples compared with those in nearshore and offshore samples, and significant negative correlations between the richness and/or abundance of ARGs and the distance to coastline (DTC) were identified, whereas different types of ARGs showed inconsistency in their relationships with DTC. The composition of antibiotic resistome showed significant correlations with nutrition-related variables (including NH 4 + -N, NO 3 − -N, and total phosphorus) and metals/metalloid (including As, Cu, Ni, and Zn), suggesting that terrestrial disturbances largely shape the antibiotic resistome. The Bipartite network showed strong associations between ARGs and mobile genetic elements (MGEs), and Partial Least Squares Path Modeling further revealed that terrestrial disturbance strength (as indicated by DTC) directly affected abiotic environmental conditions and bacterial community composition, and indirectly affected antibiotic resistome via MGEs. These findings provide insights into regional variability of sediment antibiotic resistome and its shaping path across complex ecological gradients, highlighting terrestrial disturbances as determinative forces in shaping coastal sediment antibiotic resistomes.

Xiong, Shangling↗
NASA NTRS1972

Carbon isotopic studies of organic matter in Precambrian rocks.

A survey has been undertaken of the carbon composition of the total organic fraction of a suite of Precambrian sediments to detect isotopic trends possibly correlative with early evolutionary events. Early Precambrian cherts of the Fig Tree and upper and middle Onverwacht groups of South Africa were examined for this purpose. Reduced carbon in these cherts was found to be isotopically similar to photosynthetically produced organic matter of younger geological age. Reduced carbon in lower Onverwacht cherts was found to be anomalously heavy; it is suggested that this discontinuity may reflect a major event in biological evolution.

Oehler, D. Z.↗
NASA NTRS1972

Noise generated by impingement of a jet upon a large flat board

Data were obtained on the noise generated by an air jet impinging on a large flat board. The board was large enough so that the flow leaving the edges of the board generated no significant noise. The impingement angle, nozzle shape and size, jet velocity, and the distance from the nozzle to the board were varied in the experiment. Far-field noise data are presented. The nozzle-alone noise contribution to the total noise was generally small and was subtracted from the total, leaving the impingement-only noise. The impingement-only noise was adequately correlated by eighth power of the peak impingement velocity and first power of the impingement area. The spectral data were correlated by a Strouhal number based on the peak impingement velocity and a characteristic impingement diameter.

Olsen, W. A.↗
NASA NTRS1974

Ultraviolet photometry from the orbiting astronomical observatory. XVI - The stellar Lyman-alpha absorption line

The stellar Lyman-alpha line at 1216 A was observed in 29 lightly reddened stars of spectral type B2.5 to B9 by a far-UV spectrophotometer on OAO-2. The equivalent widths obtained range from 15 A at type B2.5 to 65 A at type B8; in the late-B stars, the L-alpha line removes 2 to 3% of the total stellar flux. In this sampling, the strength of the L-alpha line correlates well with measures of the Balmer discontinuity and Balmer line strengths; luminosity classification does not seem to affect the line strength. The observed line widths also agree with the predictions of Mihala's grid of non-LTE model atmospheres. In some cases, the L-alpha line influences the interstellar column densities reported in the interstellar OAO-2 L-alpha survey. Hence, these data toward lightly reddened B2 and B1.5 stars should be regarded as upper limits only.

Savage, B. D.↗
NASA NTRS1976

Application of LANDSAT to the surveillance and control of lake eutrophication in the Great Lakes basin

The author has identified the following significant results. Computer techniques were developed for mapping water quality parameters from LANDSAT data, using surface samples collected in an ongoing survey of water quality in Saginaw Bay. Chemical and biological parameters were measured on 31 July 1975 at 16 bay stations in concert with the LANDSAT overflight. Application of stepwise linear regression bands to nine of these parameters and corresponding LANDSAT measurements for bands 4 and 5 only resulted in regression correlation coefficients that varied from 0.94 for temperature to 0.73 for Secchi depth. Regression equations expressed with the pair of bands 4 and 5, rather than the ratio band 4/band 5, provided higher correlation coefficients for all the water quality parameters studied (temperature, Secchi depth, chloride, conductivity, total kjeldahl nitrogen, total phosphorus, chlorophyll a, total solids, and suspended solids).

Rogers, R. H.↗
NASA NTRS1981

Determination of physical and chemical states of lubricants in concentrated contacts, part 2

Infrared emission spectroscopy through a window in an operating bearing continued to provide most of the information gathered on the state of lubricants subjected to elastohydrodynamic (EHD) conditions. Other measurements were traction, scanning electron microscopy and elemental surface analysis X-rays. A very significant finding was the decomposition of a naphthenic oil lubricant in the presence of small concentrations of an organic chloride. Olefins and aromatics were formed in ever increasing amounts prior to total lubricant failure. An aromatic fluid also failed in the presence of chloride. A correlation was found between changes of the alignment of lubricant molecules evidence by infrared polarization and changes of traction under varying EHD stresses.

Lauer, J. L.↗
NASA NTRS1984

A study of dynamic measurements made in the settling chamber of the Langley 0.3-meter transonic cryogenic tunnel

Tests have been conducted in a cryogenic wind tunnel settling chamber using a fast response instrumentation to measure the possible existence of temperature fronts due to a sudden or step change in the rate of liquid nitrogen injection into the circuit. No indications of such fronts were obtained using three different techniques to change the rate of nitrogen injection. The normalized pressure and velocity fluctuations at two total temperatures and over a large range of Mach numbers and Reynolds numbers were about 2 x 10 to the -7th to 2 x 10 to the -6th and about 1.8 to 3 percent, respectively. There was no evidence of liquid nitrogen droplets in the flow down to a total temperature of 140 K. The pressure fluctuation power spectra from a pressure transducer correlated with the fan blade passage through the eighth harmonic of the fundamental frequency.

Johnson, C. B.↗
NASA NTRS1994

Correlation of ozone loss with the presence of volcanic aerosols

Statistically significant reductions of ozone compared to a climatological profile have been measured above the Observatoire de Haute Provence (OHP) in Southern France (43.9 deg N, 5.7 deg E) during the months of July and August, 1992. Lidar profiles of ozone, temperature and aerosols were recorded on 25 separate nights during that time. The change in the ozone profile is correlated with the presence of volcanic aerosols from the eruption of Mt. Pinatubo. The total ozone loss amounts to approximately a 10% reduction in the total ozone column over OHP.

Mcgee, Thomas J.↗
NASA NTRS1998

Thermal Analysis and Testing of Fastrac Gas Generator Design

The Fastrac Engine is being developed by the Marshall Space Flight Center (MSFC) to help meet the goal of substantially reducing the cost of access to space. This engine relies on a simple gas-generator cycle, which burns a small amount of RP-1 and oxygen to provide gas to drive the turbine and then exhausts the spent fuel. The Fastrac program envisions a combination of analysis, design and hot-fire evaluation testing. This paper provides the supporting thermal analysis of the gas generator design. In order to ensure that the design objectives were met, the evaluation tests have started on a component level and a total of 15 tests of different durations were completed to date at MSFC. The correlated thermal model results will also be compared against hot-fire thermocouple data gathered.

Nguyen, H.↗