Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “torque control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Reactionless gimbal actuator for precision pointing of large payloads

A novel actuator for application to precision pointing gimbal systems is described. The new actuator, dubbed the Reactuator, is capable of large output torques for payload pointing while minimizing reaction torques that can excite gimbal support structure. The Reactuator is able to approach reactionless operation by using an integral wheel to absorb the reaction torques. The advantages that result are described through analysis and simulation examples. Methods for designing control algorithms for the Reactuator are discussed and the results of preliminary breadboard tests are presented.

Laskin, R. A.↗
NASA NTRS1990

A laboratory breadboard system for dual-arm teleoperation

The computing architecture of a novel dual-arm teleoperation system is described. The novelty of this system is that: (1) the master arm is not a replica of the slave arm; it is unspecific to any manipulator and can be used for the control of various robot arms with software modifications; and (2) the force feedback to the general purpose master arm is derived from force-torque sensor data originating from the slave hand. The computing architecture of this breadboard system is a fully synchronized pipeline with unique methods for data handling, communication and mathematical transformations. The computing system is modular, thus inherently extendable. The local control loops at both sites operate at 100 Hz rate, and the end-to-end bilateral (force-reflecting) control loop operates at 200 Hz rate, each loop without interpolation. This provides high-fidelity control. This end-to-end system elevates teleoperation to a new level of capabilities via the use of sensors, microprocessors, novel electronics, and real-time graphics displays. A description is given of a graphic simulation system connected to the dual-arm teleoperation breadboard system. High-fidelity graphic simulation of a telerobot (called Phantom Robot) is used for preview and predictive displays for planning and for real-time control under several seconds communication time delay conditions. High fidelity graphic simulation is obtained by using appropriate calibration techniques.

Bejczy, A. K.↗
NASA NTRSDate not supplied

Handling Qualities Considerations in Control Allocation for Multicopters

Due to multicopters’ role in advanced air mobility, there has been an increasing interest in handling qualities. This paper investigates the effect of control allocation of multicopters on handling qualities. Typically, multicopter aircraft are trimmed with equal speed on each rotor. The force generated by each rotor can be modeled, where thrust and torque of the rotor are related to the square of the rotor speed. The dynamic equations indicate that trimming pairs of motors at different RPM results in an increase of control effectiveness in the associated axis, improving bandwidth and disturbance rejection. A tradeoff occurs where power usage is no longer optimized, but handling qualities are improved in that control axis. A blade element model for multicopter, RMAC, was used to simulate how this off-nominal control allocation would affect the dynamics of a multicopter. System identification flight tests were used to validate the trends seen in RMAC. Control systems were optimized to provide improved disturbance rejection bandwidth in the axis associated with increased rotational speed. Unmanned mission task elements were performed in flight test, showing improved tracking in the lateral axis by using off-nominal mixing to increase trim speed on the rolling motors.

Handling Qualities↗
NASA NTRS2018

Reduced Gravity Airborne Mobility Testbed

Working in conjunction with the NASA Ames research center the goal of this senior design project was to develop a mobile test apparatus to enable wheel-soil interaction in a reduced gravity environment. In addition to collecting accurate wheel-soil interfacing data, a method of maintaining the density of the soil being used during the testing was developed to allow for repeatable testing conditions In order to meet these goals an annular testbed was design and built, providing an alternative to NASA’s linear rover wheel design. The circular design allowed for a smaller footprint and lighter device. The team found it was possible to set the desired slip ratio by rotating the both the annular testbed and wheel at different speeds. The Drawbar Pull force on the wheel was then measured with a torque sensor. Future work to be done includes improving the timing belt system, more robust control system, and more secure testbed base.

Liz Barrett↗
NASA NTRS1992

An electromechanical actuation system for an expendable launch vehicle

A major effort at the NASA Lewis Research Center in recent years has been to develop electro-mechanical actuators (EMA's) to replace the hydraulic systems used for thrust vector control (TVC) on launch vehicles. This is an attempt ot overcome the inherent inefficiencies and costs associated with the existing hydraulic structures. General Dynamics Space Systems Division, under contract to NASA Lewis, is developing 18.6 kW (25 hp), 29.8 kW (40 hp), and 52.2 kW (70 hp) peak EMA systems to meet the power demands for TVC on a family of vehicles developed for the National Launch System. These systems utilize a pulse population modulated converter and field-oriented control scheme to obtain independent control of both the voltage and frequency. These techniques allow an induction motor to be operated at its maximum torque at all times. At NASA Lewis, we are building on this technology to develop our own in-house system capable of meeting the peak power requirements for an expendable launch vehicle (ELV) such as the Atlas. Our EMA will be capable of delivering 22.4 kW (30 hp) peak power with a nominal of 6.0 kW (8 hp). This system differs from the previous ones in two areas: (1) the use of advanced control methods, and (2) the incorporation of built-in-test. The advanced controls are essential for minimizing the controller size, while the built-in-test is necessary to enhance the system reliability and vehicle health monitoring. The ultimate goal of this program is to demonstrate an EMA which will be capable of self-test and easy integration into other projects. This paper will describe the effort underway at NASA Lewis to develop an EMA for an Atlas class ELV. An explanation will be given for each major technology block, and the status of each major technology block and the status of the overall program will be reported.

Burrows, Linda M.↗
NASA NTRS1999

Space Station Attitude Control During Payload Operations

Evaluating the feasibility of planned robotic operations requires an analysis methodology and tools that can quickly assess proposed attitude control strategies. In this paper, an efficient approach to model the attitude dynamics of the Space Station during payload motion is presented. This approach is used to formulate an alternative numerical solution for torque equilibrium attitudes including the effect of payload velocity. It is also shown that a judicious choice of attitude command during robotic operations can substantially reduce peak attitude control momentum use.

Bedrossian, Nazareth S.↗
NASA NTRS1984

The dynamics and control of large flexible space structures, part 7

A preliminary Eulerian formulation of the in-plane dynamics of the proposed spacecraft control laboratory experiment configuration is undertaken when the mast is treated as a cantilever type beam and the reflector as a lumped mass at the end of the beam. Frequency and mode shapes are obtained for the open loop model of the beam system and the stability of closed loop control systems is analyzed by both frequency and time domain techniques. Environmental disturbances due to solar radiation pressure are incorporated into models of controlled large flexible orbiting platforms. Thermally induced deformations of simple beam and platform type structures are modelled and expressions developed for the disturbance torques resulting from the interaction of solar radiation pressure. Noise effects in the deterministic model of the hoop/column antenna system are found to cause a degradation in system performance. Appropriate changes in the ratio of plant noise to the measurement noise and/or changes in the control weighting matrix elements can improve transient and steady state performance.

Bainum, P. M.↗
NASA NTRS1980

A propulsion and steering control system for the Mars rover

The design of a propulsion and steering control system for the Rensselaer Polytechnic Institute prototype autonomous Mars roving vehicle is presented. The vehicle is propelled and steered by four independent electric motors. The control system must regulate the speeds of the motors so they work in unison during turns and on irregular terrain. An analysis of the motor coordination problem on irregular terrain, where each motor must supply a different torque at a different speed is presented. A procedure was developed to match the output of each motor to the varying load. A design for the control system is given. The controller uses a microprocessor which interprets speed and steering commands from an off-board computer, and produces the appropriate drive voltages for the motors.

Turner, J. M.↗
NASA NTRS1984

Missile rolling tail brake torque system

Apparatus for simulating varying levels of friction in the bearings of a free rolling tail afterbody on a canard-controlled missile to determine friction effects on aerodynamic control characteristics is described. A ring located between the missile body and the afterbody is utilized in a servo system to create varying levels of friction between the missile body and the afterbody to simulate bearing friction.

Davis, W. T.↗
NASA NTRS1989

High accuracy motor controller for positioning optical filters in the CLAES Spectrometer

The Etalon Drive Motor (EDM), a precision etalon control system designed for accurate positioning of etalon filters in the IR spectrometer of the Cryogenic Limb Array Etalon Spectrometer (CLAES) experiment is described. The EDM includes a brushless dc torque motor, which has an infinite resolution for setting an etalon filter to any desired angle, a four-filter etalon wheel, and an electromechanical resolver for angle information. An 18-bit control loop provides high accuracy, resolution, and stability. Dynamic computer interaction allows the user to optimize the step response. A block diagram of the motor controller is presented along with a schematic of the digital/analog converter circuit.

Thatcher, John B.↗
NASA NTRS1991

A time domain inverse dynamic method for the end point tracking control of a flexible manipulator

The inverse dynamic equation of a flexible manipulator was solved in the time domain. By dividing the inverse system equation into the causal part and the anticausal part, we calculated the torque and the trajectories of all state variables for a given end point trajectory. The interpretation of this method in the frequency domain was explained in detail using the two-sided Laplace transform and the convolution integral. The open loop control of the inverse dynamic method shows an excellent result in simulation. For real applications, a practical control strategy is proposed by adding a feedback tracking control loop to the inverse dynamic feedforward control, and its good experimental performance is presented.

Kwon, Dong-Soo↗
NASA NTRS1988

Controlled sample orientation and rotation in an acoustic levitator

A system is described for use with acoustic levitators, which can prevent rotation of a levitated object or control its orientation and/or rotation. The acoustic field is made nonsymmetrical about the axis of the levitator, to produce an orienting torque that resists sample rotation. In one system, a perturbating reflector is located on one side of the axis of the levitator, at a location near the levitated object. In another system, the main reflector surface towards which incoming acoustic waves are directed is nonsymmetrically curved about the axis of the levitator. The levitated object can be reoriented or rotated in a controlled manner by repositioning the reflector producing the nonsymmetry.

Martin B Barmatz↗
NASA NTRS2010

Space Station Control Moment Gyroscope Lessons Learned

Four 4760 Nms (3510 ft-lbf-s) Double Gimbal Control Moment Gyroscopes (DGCMG) with unlimited gimbal freedom about each axis were adopted by the International Space Station (ISS) Program as the non-propulsive solution for continuous attitude control. These CMGs with a life expectancy of approximately 10 years contain a flywheel spinning at 691 rad/s (6600 rpm) and can produce an output torque of 258 Nm (190 ft-lbf)1. One CMG unexpectedly failed after approximately 1.3 years and one developed anomalous behavior after approximately six years. Both units were returned to earth for failure investigation. This paper describes the Space Station Double Gimbal Control Moment Gyroscope design, on-orbit telemetry signatures and a summary of the results of both failure investigations. The lessons learned from these combined sources have lead to improvements in the design that will provide CMGs with greater reliability to assure the success of the Space Station. These lessons learned and design improvements are not only applicable to CMGs but can be applied to spacecraft mechanisms in general.

Gurrisi, Charles↗
NASA NTRS1992

Spacecraft attitude and velocity control system

A spacecraft attitude and/or velocity control system includes a controller which responds to at least attitude errors to produce command signals representing a force vector F and a torque vector T, each having three orthogonal components, which represent the forces and torques which are to be generated by the thrusters. The thrusters may include magnetic torquer or reaction wheels. Six difference equations are generated, three having the form ##EQU1## where a.sub.j is the maximum torque which the j.sup.th thruster can produce, b.sub.j is the maximum force which the j.sup.th thruster can produce, and .alpha..sub.j is a variable representing the throttling factor of the j.sup.th thruster, which may range from zero to unity. The six equations are summed to produce a single scalar equation relating variables .alpha..sub.j to a performance index Z: ##EQU2## Those values of .alpha. which maximize the value of Z are determined by a method for solving linear equations, such as a linear programming method. The Simplex method may be used. The values of .alpha..sub.j are applied to control the corresponding thrusters.

Paluszek, Michael A.↗
NASA NTRS1972

Bypass control valve seal and bearing life cycle test report

The operating characteristics of a bypass control valve seal and bearing life cycle tests are reported. Data from the initial assembly, leak, torque, and deflection tests are included along with the cycle life test results and conclusions. The equipment involved was to be used in the nuclear engine for the rocket vehicles program.

Lundback, A. V.↗
NASA NTRS1975

Ergometer calibrator

An apparatus is presented for accurately calibrating ergometers so that the work rate produced by the particular ergometer being calibrated is accurate. The apparatus includes a dc motor which is coupled directly to the ergometer for rotating it at various speeds. Positioned on the shaft between the dc motor and the ergometer is a torque sensor and tachometer, which feed signals to a power computer for subsequent recording. A speed controller is utilized with the dc motor.

Gause, R. L.↗
NASA NTRS1975

Airloads near the open port of a one-meter airborne telescope

An infrared telescope is mounted in a cavity in the fuselage of a C-141 airplane. The cavity is sealed off from the rest of the fuselage and can be opened to the outside for viewing. A retractable porous spoiler is installed ahead of the opening to inhibit cavity resonance. The paper presents the mean pressures, pressure fluctuations, spectra, phase, and coherence of the pressures in the cavity and on the fuselage near the cavity, along with pertinent acceleration and torque information for the aircraft structure and telescope. It is shown that a moderate spoiler extension controls resonance in normal flight attitudes and produces a cavity environment with approximately the same turbulence intensity as an attached turbulent boundary layer.

Buell, D. A.↗