Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test bed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Techno-economic assessment of emissions mitigation technologies for post-combustion CO2 capture using AMP/PZ

Minimizing the environmental impacts of amine-based post-combustion carbon capture technologies is essential for meeting environmental permitting regulations and ensuring public acceptance. Experimental test campaigns at the CO₂ capture pilot plant in Niederaussem using CESAR1 demonstrated that integrating available emission abatement technologies can significantly reduce the concentration of amines and degradation products in CO₂-depleted flue gas to below the detection limit of an infrared spectrometer. The study confirmed that proprietary dry bed technology (OEASE Aerozone™) or a second water wash can lower AMP and PZ emissions to below 1 mg/Nm³. However, to achieve very low NH₃ emissions below 2 mg/Nm³, an acid or other chemically active wash downstream of the water wash is required. A configuration with a dry bed or a double water wash results in a carbon capture cost (CCC) of 44 €/tCO₂, and a CO₂ avoided cost (CAC) of 86 €/tCO₂. A configuration with an acid wash increases the CCC to 47 €/tCO₂ and the CAC to 90 €/tCO₂ due to the amine losses in the acid waste and its treatment.

CO2 capture↗
DOE OSTI2025

Characterization of Additively Manufactured Tungsten Heavy Alloy Material (CRADA Final Report)

LLNL and Aerojet Rocketdyne, Inc. (AR), using earlier collaborative work in powder bed printing of other materials, have been collaboratively pursuing the additive manufacture of tungsten heavy alloy (WHA) material since 2014. The goal of the project was to establish the ability to produce the LLNL developed material at the AR production facility. When accomplished, AR would produce an agreed array of test samples to technically characterize the material properties via testing. AR would conduct a portion of that testing and provide those results to LLNL. The goal of this work was to perform a trial transfer of LLNL’s WHA technology to AR

36 MATERIALS SCIENCE↗
DOE OSTI2026

Gaseous Hydrogen Embrittlement of L-PBF Ni-Based Superalloys for Service in Natural Gas Turbines

Efforts to improve efficiency of industrial gas turbine engines have focused on increasing operating temperatures by use of fuel-flexible gas blends. Ni-based superalloys are susceptible to hydrogen embrittlement (HE), leading to potential risk of premature component failure. Certain turbine components exposed to hydrogen-rich environments are manufactured from additive processes like laser powder bed fusion (L-PBF). The HE susceptibility was evaluated for three Ni-based superalloys: solid solution strengthened Alloy 625, γ’/γ’’-precipitation strengthened Alloy 718, and γ’-precipitation strengthened Haynes® 282®. L-PBF samples were pre-charged under medium and high pressure gaseous hydrogen before tensile testing at temperatures up to 260 °C using a fast strain rate. Selected samples were subjected to a service conditioning heat treatment prior to hydrogen charging to evaluate the change in susceptibility after prolonged service. The susceptibility to HE and HE mechanisms of these three alloys is compared.

additive manufacturing↗
DOE OSTI2021

Evolution of global and local deformation in additively manufactured octet truss lattice structures

Additively manufactured lattice truss structures, often referred to as architected cellular materials, present significant advantages over conventional structures due to their unique characteristics such as high strength-to-weight ratios and surface area-to-volume ratios. These geometrically complex structures, however, come with concomitant challenges for qualification and inspection. In this study, compression testing interrupted with micro-computed tomography inspection was conducted to monitor the evolution of global and local deformation throughout the loading process of 304L stainless steel octet truss lattice structures. Both two- and three-dimensional image analysis techniques were leveraged to characterize geometric heterogeneities resulting from the laser powder bed fusion manufacturing process as well as track the structure throughout deformation. Variations from model-predicted behavior resulting from these heterogeneities are considered relative to the predicted and actual responses of the structures during compression to better understand, model, and predict the octet truss lattice structure compression response.

36 MATERIALS SCIENCE↗
DOE OSTI2022

FY2021 Rotating Bed Reactor for Iodine Removal from ETF Feed to Support DFLAW Start-Up

In FY20, Washington River Protection Solutions, LLC (WRPS) began a program of work to evaluate potential technologies for removal of iodine from the ETF feed. Work at the Pacific Northwest National Laboratory (PNNL) focused on ion exchange media and conventional column based deployment while Atkins and VSL focused on ion exchange media in a Rotating Bed Reactor (RBR) system. In the RBR system, the ion exchange media is loaded into a packed bed, which is rotated in the liquid to be treated. The work described in this report builds on the results from FY20 work, in particular, with regard to improving iodate removal, extending the data set to support process modeling, further comparison of RBR versus column performance, and RBR scale-up testing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Tensile Performance Sensitivity to Variations of Standard 17-4 PH Heat Treatments on LPBF-Produced Material

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical microscopy, Electron Backscatter Diffraction (EBSD), and X-ray diffraction (XRD), and mechanical properties were evaluated through uniaxial tensile testing. Based on these results, recommendations are provided for achieving improved wrought-like performance in LPBF 17-4 PH steel.

17-4 PH↗
DOE OSTI2021

High-efficiency catalytic reduction of residual oxygen for purification of carbon dioxide streams from high-pressure oxy-combustion systems

Pressurized oxy-combustion is a promising technology for carbon capture, utilization, and storage. For the captured CO 2 to be used for enhanced oil recovery or stored in geological formations, flue gas impurities, including residual O 2 in the CO 2 stream, must be purified to meet the purity specifications. A catalytic approach to reducing residual O 2 with CH 4 was investigated in this study. Five CoMn- and Cu-based catalysts were synthesized or acquired, and a reverse-flow fixed-bed reactor was used to assess their performance for O 2 removal from a simulated oxy-combustion flue gas at 15 bar. The impacts of the operating parameters on O 2 removal, such as temperature, gas hourly space velocity, O 2 /CH 4 ratio, and gas pressure, were investigated. Among the tested catalysts, the two CoMn catalysts were superior in both activity and selectivity, with the reaction lighting off at about 350 °C and achieving 99% O 2 removal at about 500 °C. Finally, the kinetics of the catalytic reaction is discussed, and the Mars–van Krevelen redox mechanism is deemed valid for describing the reaction pathway for the top-performing CoMn catalysts. The catalytic reaction was determined to be first order in CH 4 and zero order in O 2 under the test conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A GPU-based 2D shallow water quality model

In this paper, a 2D shallow water flow solver integrated with a water quality model is presented. The interaction between the main water quality constituents included is based on the Water Quality Analysis Simulation Program. Efficiency is achieved by computing with a combination of a Central Processing Unit (CPU) and a Graphics Processing Unit (GPU) device. This technique is intended to provide robust and accurate simulations with high computation speedups with respect to a single-core CPU in real events. The proposed numerical model is evaluated in cases that include the transport and reaction of water quality components over irregular bed topography and dry–wet fronts, verifying that the numerical solution in these situations conserves the required properties (C-property and positivity). The model can operate in any steady or unsteady form allowing an efficient assessment of the environmental impact of water flows. The field data from an unsteady river reach test case are used to show that the model is capable of predicting the measured temporal distribution of dissolved oxygen and water temperature, proving the robustness and computational efficiency of the model, even in the presence of noisy signals such as wind speed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Boron coated straw-based neutron multiplicity counter for neutron interrogation of TRISO fueled pebbles

Pebble bed reactors (PBRs) can improve the safety and economics of the nuclear energy production. PBRs rely on TRIstructural-ISOtropic (TRISO) fuel pebbles for enhanced fission product retention. Accurate characterization of individual fuel pebbles would enable the validation of computational models, efficient use of TRISO fuel, and improve fuel accountability. Here, we have developed and tested a new neutron multiplicity counter (NMC) based on 192 boron coated straw (BCS) detectors optimized for 235 U assay in TRISO fuel. The new design yielded a singles and doubles neutron detection efficiency of 4.71% and 0.174%, respectively, and a die-away time of 16.7 μs. The NMC has a low intrinsic gamma-ray detection efficiency of 8.71 x 10 –8 at an exposure rate of 80.3 mR/h. In simulation, a high-efficiency version of the NMC encompassing 396 straws was able to estimate the 235 U in a pebble with a relative uncertainty and error both below 2% in 100 s.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Sensitivity Analysis of MFiX-PIC Parameters Using Nodeworks, PSUADE, and DAKOTA

The study presented in this report was aimed to demonstrate UQ analysis performed not only with Nodeworks, but also two other well-established UQ software tools from the U.S. DOE’s National Laboratories (PSUADE from Lawrence Livermore National Laboratory and DAKOTA from Sandia National Laboratory). It is important to emphasize that the motivation of this study was not to determine the best UQ software, but to verify if the global sensitivity analyses from the end-to-end workflow in Nodeworks are consistent with the results of other two UQ software. The components of Nodeworks from Python’s ecosystem have been tested as standalone libraries. However, an assessment study for the complete workflow targeting a specific UQ analysis has not been performed for Nodeworks. Hence, this study is expected to serve as an equivalent of solution verification for Nodeworks using other established UQ tools as reference solution. For this purpose, three distinct flow configurations (i.e., settling bed, bubbling fluidized, and circulating fluidized bed) have been used as representative multiphase flow problems of interest. The results of the systematic simulation campaigns performed in an earlier study using the particle-in-cell (PIC) approach in the Multiphase Flow with Interphase eXchanges (MFIX) suite of solvers (i.e., MFiX-PIC) was utilized. The same set of tabulated results was provided as input to the different UQ software for global sensitivity analysis. Results for the three cases indicate that based on the Sobol’ Sensitivity Indices method the order of importance ranking determined by Nodeworks for the Sobol’ Total Sensitivity Indices is consistent with PSUADE and DAKOTA in each case for the five model parameters considered. The input files for Nodeworks for the three cases are also shared through NETL’s Gitlab repository for the reader interested in reproducibility and further analysis (See Section 1.2).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

A reusable neural network pipeline for unidirectional fiber segmentation

Abstract Fiber-reinforced ceramic-matrix composites are advanced, temperature resistant materials with applications in aerospace engineering. Their analysis involves the detection and separation of fibers, embedded in a fiber bed, from an imaged sample. Currently, this is mostly done using semi-supervised techniques. Here, we present an open, automated computational pipeline to detect fibers from a tomographically reconstructed X-ray volume. We apply our pipeline to a non-trivial dataset by Larson et al . To separate the fibers in these samples, we tested four different architectures of convolutional neural networks. When comparing our neural network approach to a semi-supervised one, we obtained Dice and Matthews coefficients reaching up to 98%, showing that these automated approaches can match human-supervised methods, in some cases separating fibers that human-curated algorithms could not find. The software written for this project is open source, released under a permissive license, and can be freely adapted and re-used in other domains.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Experimental Tests of Lateral Bedload Transport Induced by a Yawed Submerged Vane Array in Open-Channel Flows

This work proposes the use of an array of yawed porous vanes to control the lateral bedload transport by locally steering bedform migration and maximize the amount of sediments redirected toward a potential sediment extraction system or bypass channel. A laboratory experiment was conducted in a quasifield-scale channel with an array of permeable vanes installed on one side, in live-bed conditions under bedload dominant regime, i.e., negligible suspended load. A baseline experiment without vanes was also performed for comparison. The evolution of migrating bedforms of different scales was tracked in space and time using a high-resolution, state-of-the-art laser scanning device. The bedload transport rate in the streamwise direction was first calculated using bedforms’ geometry and migration velocity, and then spatially distributed over the entire monitored area using a new Eulerian-averaged grid-mapping method. This allowed us to introduce a new methodology to estimate the lateral bedload transport using control volume theory and applying mass conservation. Quantitative assessments of lateral bedload transport along the channel yield consistent results, suggesting that the vanes effectively move sediments laterally as intended. Under the investigated setup, the maximum lateral sediment transport rate ranges from 9% to 18% of the whole domain-averaged streamwise transport rate. The developed methodology also allowed to identify the location where sediment capture could be maximized for the given vane spatial distribution.

42 ENGINEERING↗
DOE OSTI2022

Modeling of a Generic Pebble Bed High-temperature Gas-cooled Reactor (PB-HTGR) with SAM

This report presents the modeling of the core of a generic pebble-bed reactor (PBR) at the system level using the System Analysis Module (SAM) code. This work is an extension of a previous work by the authors (Ooi et al. (2021)) that used the so-called 2-D ring model approach to model the PBMR-400. With the new approach, the pebble bed of the reactor is modeled with multiple PBCoreChannel components with spherical heat structures which allows the code to calculate thermal fluid parameters with built-in closure relations. The new core-channel approach is an improvement to the 2-D ring model approach as it does not introduce geometric distortions to the model and thus reduces the uncertainties of the predictions. In addition to thermal fluid simulations, point kinetics (PKE) are included to the model. Simulations are performed under a steady-state normal operation condition and a load-following transient scenario. This particular transient scenario is chosen as it tests both the thermal fluid and neutronics aspects of the model. The predicted results from both the steady-state and transient scenarios are compared with the results by Stew- art et al. (2021) who performed similar simulations with a Griffin-Pronghorn coupled tool. Despite the differences between the codes, with SAM being a system-analysis code and Pronghorn being a porous-medium code, both sets of results compare favorably. The over- all profiles and trends of the predicted temperatures and reactivities from the SAM and Griffin/Pronghorn simulations are similar, with some differences in their predicted values. The first part of the report covers the significance of a relatively fast-running approach that is capable of modeling the pebble bed reactor at the system-level while simultaneously capturing the radial thermal behavior of the core. Then, the modeling approach used in this work is discussed in details. Lastly, the results and comparisons with the Griffin/Pronghorn simulation are presented.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Validation of Streaklines as Recorders of Synoptic Flow Direction in a Deltaic Setting

Knowledge of the flow patterns within distributary systems is key for understanding deltaic hydro- and morpho-dynamics, yet synoptic measurements of flow fields remain virtually nonexistent. As a means of overcoming this problem, a small number of studies have used biogenic surface films as synoptic flow tracers, under the assumption that biofilm streaklines are tangent to the local flow direction. Here we rigorously test this assumption and show that, despite flow patterns that change severely in space and time (over a range >270°), streaklines are relatively accurate synoptic flow tracers for the Wax Lake Delta, in Louisiana. When the incoming discharge was greater than 2400 m3/s with stable or falling tides, the streakline-derived flow direction departed from near bed flow direction measurements of 22.8° (root mean square). When the discharge was greater than 2400 m3/s and the tides were rising greater than 0.03 m/hr, they were accurate within 28.0°. Under conditions of discharge less than 2400 m3/s and tidal change less than a positive 0.03 m/hr, they were accurate within 33.3°, while during low discharge and rising tides they were accurate within 58.9°. Accuracy varied with distance from the delta, with proximal sites having greater precision. Our results demonstrate that a streakline-derived flow direction can characterize the spatiotemporal variability in the flow directions, but that the accuracy is significantly influenced by the hydrodynamic conditions and location within the network.

58 GEOSCIENCES↗
DOE OSTI2023

Characterizing the seismic response of a molten salt nuclear reactor

Abstract One Generation IV nuclear reactor, which uses a fluoride salt as a coolant, graphite reflector blocks as a moderator, and circulating buoyant TRISO pebbles as fuel is at an advanced stage of development. To characterize the seismic behavior of components of this reactor, validate numerical models for analysis, and develop recommendations for design, a set of earthquake‐simulator experiments on a scaled model of the reactor vessel and its internals was executed on a six‐degree‐of‐freedom earthquake simulator. The model was seismically isolated at its base using two types of spherical sliding bearings. The scaled model involved representations of the prototype reactor vessel, core barrel, reflector blocks, coolant, and spherical fuel pebbles. The material and geometric properties of different test components were selected based on a dynamic similitude scaling analysis and an approximate length scale of 0.4. Four sets of three‐component earthquake motions were used as inputs for testing. Instrumentation on the test specimen recorded the dynamic responses of the outer vessel, core barrel, and reflector‐block assembly, the hydrodynamic responses (sloshing and hydrodynamic pressure) of the liquid coolant, pebble consolidation under earthquake shaking, and the behavior of the isolation systems. This paper describes the design of the experiments and presents key results from the tests. The dynamic responses of the outer vessel, core barrel, and the reflector blocks revealed that the components responded as a unit for the intense shaking used in the experiments. The sloshing response of the fluid in a thin annulus near the perimeter of the vessel was heavily damped. The change in the packing fraction of the pebble bed under repeated, intense 3D earthquake shaking was less than 3%. Seismically isolating the vessel substantially reduced demands on its internal components.

Engineering↗
DOE OSTI2022

Repurposing the θ (Al 2 Cu) phase to simultaneously increase the strength and ductility of an additively manufactured Al–Cu alloy

The Al–Cu–Mn–Zr (ACMZ) cast family of alloys offers unique properties and value propositions for higher strength, higher temperature lightweight components of future vehicles. Earlier research has demonstrated trade-offs in the selection of the alloy chemistry in which an increase in Cu content from 6 up to 9 wt% improves hot tear resistance but lowers ductility. However, a recent study has demonstrated that higher-Cu (9Cu) ACMZ fabricated with laser powder bed fusion additive manufacturing (AM) results in an increase in both ductility and strength when compared to as-aged microstructure of cast 9Cu alloys. The mechanisms of differing mechanical performance of the cast and AM ACMZ alloys are elucidated in the current paper through the utilization of in situ high energy x-ray diffraction (HEXRD) tensile testing wherein lattice strains of different phases are calculated and correlated to their stresses. The ACMZ alloys consisted of theta (θ) and theta prime (θ') phases (both Al 2 Cu in nominal composition) within an aluminum matrix. The larger micron-size θ phase which decorated the grain boundaries in 9Cu ACMZ cast alloys recorded small lattice strains, while the submicron, homogeneously distributed θ phase in the 9Cu ACMZ AM alloy recorded considerably higher lattice strains. The maximum stress reached in the θ phase for the cast 9Cu alloy was found to be ~280 MPa, which was lower than the AM 9Cu alloy which registered a maximum stress of ~1.4 GPa. These measurements indicate that delayed fracture of the finer intermetallic phases simultaneously improves the ductility and strength of AM 9Cu alloy relative to the cast 9Cu alloy, which exhibits early fracture of the larger intermetallic particles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Scalable in situ non-destructive evaluation of additively manufactured components using process monitoring, sensor fusion, and machine learning

Laser Powder Bed Fusion (L-PBF) Additive Manufacturing (AM) is among the metal 3D printing technologies most broadly adopted by the manufacturing industry. However, the current industry qualification paradigm for critical-application L-PBF parts relies heavily on expensive non-destructive inspection techniques, which significantly limits the use-cases of L-PBF. In situ monitoring of the process promises a less expensive alternative to ex situ testing, but existing sensor technologies and data analysis techniques struggle to detect sub-surface flaws (e.g., porosity and cracking) on production-scale L-PBF printers. In this work, an in situ NDE (INDE) system was engineered to detect subsurface flaws detected in X-Ray Computed Tomography (XCT) directly from process monitoring data. A multilayer, multimodal data input allowed the INDE system to detect numerous subsurface flaws in the size range of 200–1000µm using a novel human-in-the-loop annotation procedure. Furthermore, a framework was established for generating probability-of-detection (POD) and probability-of-false-alarm (PFA) curves compliant with NDE standards by systematically comparing instances of detected subsurface flaws to post-build XCT data. Here, we also introduce for the first time in the AM in situ sensing literature the a 90/95 – the flaw size corresponding to a 90% detection rate on the lower 95% confidence interval of the POD curve. The INDE system successfully demonstrated POD capabilities commensurate with traditional NDE methods. Traditional ML performance metrics were also shown to be inadequate for assessing the ability of the INDE system’s flaw detection performance. It is the hope of the authors that future studies will adopt the POD and PFA approach outlined here to provide better insight into the utility of process monitoring for AM.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Operando visualization of porous metal additive manufacturing with foaming agents through high-speed x-ray imaging

Porous metals find extensive applications in soundproofing, filtration, catalysis, and energy-absorbing structures, thanks to their unique internal pore structure and high specific strength. In recent years, there has been an increasing interest in fabricating porous metals using additive manufacturing (AM), leveraging its unique advantages, including improved design freedom, spatial material control, and cost-effective small-batch production. In this study, we conducted pioneering operando visualization of AM porous metal using a laser powder bed fusion (L-PBF) setup combined with a high-speed synchrotron x-ray imaging system. Single track printing experiments using Ti6Al4V (Ti64) combined with titanium hydride (TiH 2 ) and sodium carbonate (Na 2 CO 3 ) as foaming agents, with varying mixing ratios were performed under different processing conditions. Here. the results elucidate the dynamic development of porosity formation. The average pore size is significantly influenced by the particle size of foaming agents when pore coalescence is absent. For all foaming agent content tested in the current study, the number of pores is found to be more sensitive to changes in laser power than in laser scanning speed. Increasing linear energy density (increasing laser power or reducing laser scanning speed) promotes the foaming agent activation thereby porosity formation. However, high linear energy density skews pore distribution towards the surface despite forming deeper melt pools. In addition, the impact of additional factors including foaming agent's laser absorptivity and decomposition kinetics with respect to AM time scales should be carefully considered to avoid ineffective activation of foaming agents during the AM of porous metals.

36 MATERIALS SCIENCE↗