Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Sodium Exposure Tests of A709 Steel (FY2020 Progress Report)

Sodium exposure tests were conducted on the first commercial heat, H58776 of A709 steel. Six different processing and heat treatment conditions were investigated, including three processing conditions, namely, Argon-Oxygen-Decarburization (AOD), Electro-slag Remelting (ESR), and Electro-slag Remelting with subsequent homogenization (HOMO), and two heat treatment conditions, i.e. solution annealing at 1100°C (SA1100°C) or 1150°C (SA1150°C). Specimens of AOD-SA1100°C, AOD-SA1150°C, ESR-SA1100°C, ESR-SA1150°C, HOMO-SA1100°C, and HOMO-SA1150°C were tested in sodium at 650°C and for times up to 10,152 h. Specimens in the AOD-SA1100°C and AOD-SA1150°C conditions were also tested in sodium at 550 and 600°C. Parallel thermal aging experiments were carried out for comparison with sodium exposure tests to separate the thermal and sodium effects. It was found that A709 H58776 generally showed a weight loss after sodium exposures at 650°C except a few data points of the ESR-SA1100°C specimens. The corrosion rate showed large variations in the initial stage and decreased with increasing exposure time. Long-term exposure tests are needed to determine its steady-state corrosion rate. The AOD-SA1100°C and HOMO-SA1100°C specimens showed similar tensile responses after thermal or sodium exposures at 650°C. The yield stress increased, the ultimate tensile strength decreased, and the uniform and total elongations were reduced after thermal or sodium exposures. A longer exposure time had a minimal effect on the tensile strength but further reduced the tensile ductility. The sodium-exposed specimens had higher tensile strength than the thermally-aged specimens. In contrast, the ESR-SA1100°C specimens showed an increase in the yield stress and the ultimate tensile strength after thermal or sodium exposures at 650°C and ~10,000 h. The AOD-SA1150°C and ESR-SA1150°C specimens showed similar tensile behavior after thermal or sodium exposures at 650°C.Thermal or sodium exposures at 650°C increased the yield stress, decreased the ultimate tensile strength, and reduced uniform and total elongations. There were minimal differences in tensile properties between the sodium-exposed and thermally-aged specimens after an ~3000 h exposure. After an exposure for ~10,000 h the sodium-exposed specimens showed higher yield stress and ultimate tensile strength and lower uniform and total elongations than the thermally-aged specimens. For the HOMO-SA1150°C specimens, thermal or sodium exposures at 650°C significantly increased the yield stress but had a minimal effect on the ultimate tensile strength. Both uniform and total elongations were significantly reduced at an exposure time of ~3,000 h, and they were further reduced after an exposure of ~10,000 h. The sodium-exposed specimens had lower tensile ductility than the thermally-aged specimens. Before exposure, the stress-strain curves of the specimens in all six processing-heat treatment conditions showed serrations indicating the dynamic aging effect at 650°C. Thermal aging or sodium exposures at 650°C after ~10,000 h completely removed the serrations of the flow curves in A709 H58776, indicating strong precipitation during thermal or sodium exposures. Longer-term sodium exposure tests are needed to determine the steady-state corrosion rates in sodium for A709 H58776 and fully understand the influence of sodium exposures on its mechanical performance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shear Behavior of Artificial Clay Seams within Bedded Salt Structures

Bedded salt contains thin layers of clay, also known as clay seams, in-between far thicker layers of salt. These inhomogeneities are thought to have first-order effects on the closure of nearby drifts and potential roof collapses. Despite their importance, characterizations of the peak shear strength and residual shear strength of clay seams in salt are extremely rare in the published literature. A previous paper reported results from laboratory direct shear experiments on clay seam samples from the Permian Basin in New Mexico. These clay seams behaved similar to intact salt, which was attributed to the abundance of salt crystals intersecting the clay seams. None of those specimens contained a distinct ¼" - ½" (6 -12 mm) thick clay seam, as has been observed in drifts at the Waste Isolation Pilot Plant (WIPP). Due to the difficulty in obtaining WIPP samples with these types of clay seams, artificial seams of bentonite and brine sandwiched between sections of salt were created and shear tested. Eight 4" diameter samples were created with either a ¼" or ½" a thick seam and then consolidated at 3000 psi prior to shear testing. The direct shear tests on these samples were performed at nominal normal stresses representative of expected WIPP in-situ conditions (500 to 1500 psi). The resulting shear stress vs. shear displacement curves exhibited a peak followed by a gradual decay of shear strength. The shear stress never transitioned to a true residual shear stress plateau, so the final shear strength at the end of each test (0.75" of shear displacement) was analyzed instead. Both the peak shear strength and the final shear strength conformed to Mohr- Coulomb behavior with friction angles and cohesion strengths consistent with a saturated, highly consolidated, clay. These new artificial clay seam results and the previous clay-interspersed-with-salt results likely bound the expected shear behavior of WIPP clay seams.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

U Metal Oxidation with Steam (U)

The Savannah Rive National Laboratory 9SRNL) is evaluating a method to produce uranium oxide (UO 2 ) from uranium metal using steam. The typical methods for making UO 2 yield powders with particle-size ranges of 1 to 50 micron. The goal of the steam oxidation is to produce a depleted uranium (DU) product with a larger particle size that can be used as a surrogate for testing physical and mechanical process techniques to refine uranium and/or plutonium bearing residues. Several studies in the literature indicated that reactions between uranium metal and steam will yield UO 2 as fine powders in the 160 to 500 °C range, but granular materials form above 500°C. Above 880 °C, a hard compact scale forms on the U metal. Furthermore, sintering of UO 2 occurs at about 1300 °C, but it has been stated that the presence of steam enhances the sintering characteristics of UO 2 . Initial studies into the oxidation of DU metal in an atmosphere of argon and steam have been completed. Oxidation of depleted uranium metal in Ar/steam at 600, 710, 700, and 830 °C yielded at UO 2 product with little or no impurity at each temperature. Although not enough sample was available to perform sieve analysis for particle size distribution, SEM images reveal that a significant volume fraction of the products at 710, 770, and 830 °C exceeds 100 microns. The material produced at 600 °C was too fine for programmatic needs. Questions associated with the UO 2 include morphology of product, mechanical strength of the particles, and performance in milling operations. The size of the samples produced in these tests did not allow for quantitative assessment of particle size of mechanical strength. A qualitative assessment of the particles formed at 710, 770, and 830 °C was that the samples produced at 710 and 770 °C were friable, and the sample produced 830 °C had more mechanical strength. Sintering of the samples in Ar/steam at 970 °C appeared to increase the strength of the particles without changing their general particle size characteristics. Due to the small sample sizes, the increase in strength could not be quantified. If the sintering at 970 °C is inadequate, higher sintering temperatures in Ar/steam can be evaluated. Future work will increase scale of the steam oxidation conditions which yield the most-favorable particle-size distributions with sufficient mechanical strength for programming usage. Further consideration will be given to oxidation temperature, steam addition to the reaction vessel, U metal pretreatment, and sintering conditions after oxidation. The UO 2 production could involve a two-step process where particles are formed in steam at lower temperatures (700-850 °C) and then sintered in Ar/steam at elevated temperatures (950-1200 °C). Larger samples (50-100 g each) will provide sufficient UO 2 product for sieve analysis and assessment of mechanical strength relatives to subsequent milling operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Report on use of Inoculants in Missile Application Alloys

This report documents the status of current inoculant research relevant to missile application alloys and MTCR control language. The information is intended to provide data on current inoculants for us determining the current state of development and identifying potential research directions. Although there has been significant scientific research into the development and synthesis of inoculants, their current availability is limited is traditional powder inoculants employed during casting processes. However, research continues the development of complex oxides, ribbon materials, high entropy alloys, and other inoculant product forms, including the use of inoculants in the melt pools produced during additive manufacturing. Research to date has focused primarily on aluminum and steel alloys with emphasis on refining grain structures and evolving equiaxed morphologies while increasing strength and castability. The primary inoculants in steel and cast irons include TiN, SiC, FeSi75, and Ce which have increased strength properties. Chief inoculants for Al alloys often include TiC, SiC, Al3Sc(x) and TiB2 to aid in precipitation and refinement. Ti and Ni alloys have fewer research activities involving inoculants, although TiN, TiB, ZrN and LaB6 (for Ti alloys) and WC, Co3FeNb2, and CrFeNb (for Ni alloys) have been used. Sic, Al2O3, Mg and Ti are key inoculants for Mg alloys. Multiple cast alloys from each of the material classes demonstrated increased strength and performance properties using inoculants, with several approaching requirements applicable to missile service environments. The continued evolution of advanced manufacturing capabilities is making it easier to produce high temperature near net shape structural materials using inoculant powders. These shapes may include the geometric shapes addressed within the MTCR (tubes and limited wall thicknesses). The use of inoculants may enable further development of high temperature alloys into near net shapes traditionally produced via casting processes due to limited ductility. This may decrease material and manufacturing costs. In addition, inoculation provides controlled kinetics and achievable chemical segregation that enables potential for far-from equilibrium thermodynamic microstructures and chemistries that could provide new metastable alloy states and subsequent properties to address co-design engineering constraints, including needs for increased strength and ductility. It is recommended that specific material combinations within these alloy classes be carefully watched as the materials evolve, with controls aimed at those having material properties above current MTCR levels. This specifically includes the use of refractory inoculants in alloys, and the application of inoculants in high strength and high temperature alloys via additive manufacturing processes, with care to link capabilities to product forms similar to the current requirements on tube geometries and material feed stocks. The continued development of nanoparticle inoculants will increase strength and ductility of high strength castings and additive manufactured metallic components. For example, adding inoculants into the casting of maraging steels and other precipitation strengthened alloys may drastically elevate mechanical properties above the control limit of current regulations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

IACMI Project 4.7: Pultruded Textile Carbon Fiber for Spar Caps (Final Report)

The primary objective of this project was to demonstrate the potential to significantly reduce the cost of wind turbine blades with carbon fiber reinforced polymer (CFRP) structure. Applicability of textile carbon fibers (TCF) were evaluated for use in pultruded spar cap (SC) elements as a path to cost reduction for utility scale wind turbine blades. In earlier work for the Department of Energy (DOE) Wind Energy Technologies Office (WETO), a collaboration of Sandia National Laboratory (SNL), Oak Ridge National Laboratory (ORNL), and Montana State University has demonstrated potential for pultruded TCF to compete with infused fiberglass and commercially available carbon fiber pultruded sections for spar cap construction. In the design cases evaluated, the TCF sections fared well when compared on cost per unit composite stiffness and cost per unit composite compressive strength for those designs [1]. Both stiffness and compressive strength tend to be key factors in the design of blade composite Spar Cap which carry the bulk of the blade structural loads in bending. Spar Cap design tends to distribute largely symmetric tensile and compressive stresses to opposite sides of the spar structure, but since carbon fiber composite compressive strength is typically 20-50% lower than tensile strength, the compressive loading reaches failure levels well before the tensile loading. Stiffness is critical in containing the large tip deflection in high wind loading situations. However, materials and process development were very limited in the earlier study and the work in this project was expanded to make the comparative information more representative of what will be required in order to make further inroads towards implementation. Similar to that study, this project team confirmed that the primary materials of interest for pultruded spar cap elements should be thermoset (TS) resins reinforced by carbon fibers, utilizing as high a percentage of TCF as practical to benchmark cost and performance against commercial carbon fibers. To make the closest comparison possible and eliminate specific test article size, resin selection, and equipment/operational nuance effects, the team planned to pultrude sections with 100% commercially available carbon fiber (Panex 35 carbon fiber from Zoltek) as well as samples utilizing high fractions of TCF. The resin system chosen was based on formulations recommended by large wind industry supplier Hexion and consisted of Hexion resin RSL-4597, curing agent CCA-138, and internal mold release additive 117, along with common kaolin filler ASP400P from BASF. As commonly deployed in spar cap configurations, the team had a mold built to pultrude a rectangular spar cap element of 100mm width and 3mm thickness. The extremely limited number of samples produced for the earlier study were produced with a “generic” epoxy utilized for a variety of applications by the pultruder contracted to produce test articles for demonstration purposes. More importantly, those samples were produced at a fiber fraction only slightly over 50%. Based on feedback from our industrial advisory team for that project and strongly recommended by this project team, the consensus is that it is highly desirable to obtain fiber fractions of 65-68% for significant penetration in wind blade spar cap. Although this requirement has yet to be exhaustively confirmed in readily available information, this was established as a project goal and informally decided we needed to exceed 60% fiber fraction to gain serious industry consideration. Previous TCF pultrusion trials have been challenged by the lack of robust TCF packages, resulting in non-uniform tension across and between tows, as well as excess labor and waste for removal of interleaved paper. The non-uniform tension and associated intermingling of tows in textile acrylic fiber tows and associated difficulties created from broken filaments in carbon fiber conversion inhibit the ordered packing necessary to enhance fiber fraction elevation. (These “cross-overs” are not considered undesirable for textile applications and there is some sense that they might be advantageous for those applications). In addition to work that is ongoing at the acrylic fiber manufacturers to improve their formats, The Institute of Advanced Composites Manufacturing Innovation (IACMI) Project 6.12 (report PA16-0349-6.12-01) [2] has developed and demonstrated a more robust packaging and creeling approach that at least partially addresses these issues, thus improving control of the TCF feed into the pultrusion unit. It was hoped that these and other improvements currently being implemented would allow us to achieve fiber fractions at least approaching these fiber fraction targets. During this project, sections utilizing 100% commercially available carbon fiber reinforcement were produced as a baseline, as well as sections reinforced with about 94% TCF and the balance being commercially available fiber for comparison. The most important finding was that similar to results reported in the earlier WETO-funded project and results from tests of TCF reported at IACMI meetings, this work demonstrated that sections pultruded with TCF in an epoxy resin frequently utilized in actual spar cap production had stiffness and compressive strengths largely comparable to similar sections pultruded with a commercially available carbon fiber also frequently utilized in the wind industry. Although the amount of that data is limited, some of the tensile strength results were actually closer than would have been expected based on fiber strength results provided by the TCF and commercial fiber producers. The actual test data are reported and discussed in detail in Section 5. The pultruded sections dominated by TCF reinforcement were approximately 8-10% lower in fiber fraction than for the sections produced using commercial fiber alone, making direct comparison difficult. The COVID-19 project has provided significant insight into the current state-of-the-art with various TCF product forms. The data obtained in this project will guide the planned improvements at the precursor level, especially in attaining uniform tensioning and payout to facilitate enhanced fiber fractions and overall processability of the TCF composites. The project team is providing guidance to stakeholders concerning the attributes, needs, and potential demand for TCF in wind blade spar caps. Results achieved in this project are consistent with findings in the related work cited [1] and support this guidance and the high potential for this product type. TCF precursor-producing partners continue to express interest in enhancing their product forms and the team looks forward to working with these improved materials as they become available.

42 ENGINEERING↗
DOE OSTI2022

Mechanical evaluation of WC-Co materials with varying microstructures

Tungsten carbide–cobalt materials are useful in a variety of extreme applications due to a desirable blend of properties, yet the technology has not significantly changed since their initial development in the 1920s. The mechanical properties of this class of materials is highly dependent on two variables, the size of the tungsten carbide grains, and the amount of binder phase present in the final body. In this study, the amount of binder phase is isolated across three commercial materials from the same manufacturer with three different grain sizes to investigate the effect on mechanical properties. The mechanical properties investigated are indentation hardness, flexure and tensile strength, as well as fracture toughness. In general, an increase in hardness and tensile strength with decreasing grain size was observed, while the fracture toughness showed the opposite trend with toughness increasing with increasing grain size. The flexure strength results did not show a correlation to grain size. Fractographic analysis identified the dominant strength-limiting flaw for each sample, which largely were in the form of porosity. Other flaws types, such as inclusions from the milling process, clusters of large grains, and machining cracks from the surface finishing process, were also identified. Finally, Weibull analysis was performed and deemed appropriate for analysis of these materials, but strength-size scaling was not conducted due to the variability in the strength-limiting feature between the different specimen geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Critical review of the Mogi failure criterion based on true-triaxial laboratory data analysis and theoretical considerations

The influence of the intermediate principal stress, σ 2 , is disregarded when rock strength is analyzed using the Mohr-Coulomb or Hoek-Brown criteria. Several polyaxial strength criteria have been proposed to account for the influence of σ 2 . One of the methods that received considerable attention is the Mogi criterion. The criterion modifies the Nadai or Drucker-Prager approaches by exchanging the normal octahedral stress with what is introduced as the mean effective stress, σ m,2 . This change is based on experimental evidence that the influence of the intermediate principal stress on strength is less pronounced than the influence of the minimum principal stress. However, the Mogi criterion was derived somewhat empirically and consequently it is essential to analyze its potential theoretical deficiencies. In the current note, we analyzed the Mogi failure criterion, describing its characteristics in both τ oct –σ m,2 and σ 1 -σ 2 spaces. We investigated the relation between Mohr-Coulomb and Mogi criteria, which marks the basis for the commonly used Mogi-Coulomb approach. Here, we compared the performance of the Mogi criterion against available polyaxial strength data using three fitting approaches: Mogi-Coulomb based on triaxial compression results only, linear Mogi based on all polyaxial strength results, and power law Mogi also based on all data. The analysis reveals several serious deficiencies of the Mogi approach which all suggest that the Mogi criterion cannot properly represent the σ 2 dependence of rock strength in many cases.

58 GEOSCIENCES↗
DOE OSTI2025

Effects of HCP/BCC element ratios on the room-temperature tensile properties of Ti-Zr-Hf-Nb-Ta refractory high-entropy alloys

Equiatomic and non-equiatomic Ti-Zr-Hf-Nb-Ta refractory high-entropy alloys (RHEAs) were arc melted, homogenized, cold rolled, and recrystallized to produce single-phase, body-centered cubic (BCC), microstructures with weak texture and equiaxed grains 76–199 μm in size. Here, the non-equiatomic alloys had either a 60:40 or 80:20 atomic ratio of hexagonal close-packed (HCP) elements (Ti + Zr + Hf) to BCC elements (Nb + Ta). Alloy compositions were measured after thermomechanical processing to determine the concentrations of the major (substitutional) and minor (interstitial) elements. We investigated how elastic constants and uniaxial tensile properties were affected by changes in the relative concentrations of the constituent elements at fixed HCP:BCC ratios. Yield strengths ranged from 801 to 922 MPa and ultimate tensile strengths from 815 to 933 MPa. Good agreement is obtained between the experimental yield strengths and those predicted by a strength theory based on edge dislocations indicating that the observed compositional effects are due to their effects on shear modulus and volume misfit. Fracture occurred by dimpled rupture with fracture strains of 19.4%–25.7%, but uniform strains were an order of magnitude lower at 1.1%–3.2%, calling into question the useable ductility (prior to necking) of RHEAs considered to be ductile based on their fracture strain. Contrary to predictions in the literature that HCP elements promote ductility, our present results show that increasing the HCP:BCC ratio decreases both the total strain and the uniform strain. Similar trends were not evident in the yield or ultimate strengths; rather, strengths were affected mainly by shear modulus and volume misfit.

BCC high-entropy alloys↗
DOE OSTI2025

Statistical fracture behavior of doped UO 2 using a ball-on-ring equibiaxial flexure test method

Metal oxide dopants, such as titanium and chromium oxides, have garnered considerable attention for their potential to increase grain size (≥ 30 µm) in UO 2 fuel, purportedly enhancing fission gas retention during reactor operation. Fuel performance is significantly impacted by fuel fracture behavior, so it is important to understand the effects of enhanced grain size and dopant content on UO 2 fuel fracture. UO 2 pellets were doped with 0.1 wt% TiO 2 and 0.3 wt% Cr 2 O 3 to alter density and grain size. Inductively coupled plasma mass spectroscopy measured dopant levels pre- and post-sintering. X-ray diffraction revealed lattice changes and microstrain via Rietveld refinement. Field emission scanning electron microscopy determined grain sizes of approximately 30 µm for TiO 2 doping and 7 µm for Cr 2 O 3 doping. Transverse rupture strength tests were performed on over 30 samples per dataset to obtain characteristic strength and Weibull modulus. Results indicate no statistical difference in fracture strength between 0.1 wt% TiO 2 doped UO 2 and undoped UO 2 , while 0.3 wt% Cr 2 O 3 doped UO 2 exhibited a 20% decrease in fracture strength. Doped UO 2 samples also showed reduced Weibull modulus compared to undoped UO 2 , suggesting increased scatter in fracture strength. This study's findings suggest that titanium and chromium oxide doping in UO 2 , regardless of grain size, induce residual stresses, decreasing fracture strength and increasing variability in fracture behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Extraction of neutron-capture cross sections on 92 Zr using the charge-exchange Oslo method

The 93 Nb (𝑡, 3 He ) reaction at 115 MeV/nucleon was studied to demonstrate that nuclear level densities and 𝛾-ray strength functions can be extracted from charge-exchange reactions at intermediate energies using the Oslo technique. The matrix of excitation energy in 93 Zr, reconstructed from the (𝑡, 3 He ) reaction, versus the energy of 𝛾 rays emitted by the excited 93 Zr nuclei, was obtained in an experiment with the S800 Spectrograph operated in coincidence with the GRETINA 𝛾 -ray detector. The extracted level density and 𝛾 -ray strength function obtained by applying the Oslo method to this matrix were used to estimate the 92 Zr⁢(𝑛,𝛾) ⁢93 Zr cross section by combining the new results with other experimental data and theoretical calculations for 𝐸⁢1 and 𝑀⁢1 strength functions at higher energies. Good agreement with direct measurements of the 92 Zr⁢(𝑛,𝛾)⁢ 93 Zr cross section was found. The contribution from the upbend in the extracted 𝛾-ray strength function was important to achieve the consistency, as the neutron-capture cross section without this contribution is significantly below the direct measurements otherwise. Since charge-exchange reactions at intermediate energies have long been used for extracting Gamow-Teller strengths, the successful demonstration of the charge-exchange Oslo method enables experiments in which (𝑛,𝛾) cross sections and Gamow-Teller strengths can be measured simultaneously, which is of benefit for astrophysical studies.

90 ≤ A ≤ 149↗
DOE OSTI2021

Failure in Confined Brazilian Tests on Sandstone

Strength of rocks in the confined tension region, where the minimum principal stress is tensile, has only infrequently been measured and is not well understood. Quasi-static confined Brazilian tests under a range of confining stresses (2.76 to 27.58 MPa) where used to determine the strength of sandstone in the confined tension region. The test results indicate that the strength in the confined tension region was a strong function of the intermediate principal stress: increasing the intermediate principal stress significantly increased the strength of the sandstone. The strength data were well fit by the Mogi–Coulomb criterion, which accounts for the intermediate principal stress. Unconfined Brazilian strength data were not well fit to the Mogi–Coulomb criterion derived from the confined Brazilian test data, consistent with a transition from tensile to shear processes dominating failure with increasing confining pressure. Observations of post-failure fracture surfaces reveal more indication of shear processes with increasing confining pressure. Numerical simulations from combined finite-discrete element method are compared to the experimental results and reflect similar conditions for failure compared to the experimental tests in the confined tension region.

42 ENGINEERING↗
DOE OSTI2023

A Sustainable and Environmentally Friendly Concrete for Structural Applications

The purpose of this study is to utilize waste products—precipitated calcium carbonate (PCC) and upcycled recycled concrete aggregate (upcycled RCA or UCA)—in civil works projects. To do so, tests must be performed to determine the engineering properties of the materials in which PCC and UCA are sequestered. PCC is a fine to coarse grain waste product generated during the production of sugar from sugar beets. UCA is produced from demolished and returned concrete by the extraction of primarily calcium and alkalinity. The study also includes the use of both PCC and UCA in the same concrete mix design. The test results on PCC alone show that the optimum content to achieve a minimum 28 MPa (4000 psi) compressive strength is 25% and 30%. The corresponding compressive strength of mixes in which conventional aggregate was replaced by UCA is about 48 MPa (7000 psi) to 55 MPa (8000 psi) at the same water: cement ratio (0.44) by weight. The compressive strength of concrete with 25% to 30% cement replaced by PCC and varying aggregates replaced with UCA ranges from 19.3 to 40 MPa (2800 to 5800 psi). Other tests on PCC and UCA include tensile strength of 2 to 3 MPa (293 to 423 psi) and flexural strength of 1.3 to 1.9 MPa (183 to 279 psi). Analytical techniques such as X-ray diffraction (XRD), energy-dispersive X-ray spectrometry (EDX), and scanning electron microscopy (SEM) were used to identify the constituent elements and chemical compounds present in PCC, including calcium carbonate and silica. Based on the test results, the composition of PCC by weight indicates 45.9% calcium, 39.4% oxygen, and 9.2% carbon. Based on the results of this study, we can expect to reduce carbon emissions in the production of cement and aggregates, as well as utilize waste products in the civil engineering field.

42 ENGINEERING↗
DOE OSTI2022

A Novel Rotating Flexure-Test Technique for Brittle Materials with Circular Geometries

The four-point bend test is one of the simplest and often the preferred flexural strength evaluation method for brittle materials. In this loading mode, fracture often initiates from a critical surface (or subsurface) flaw when subjected to a tensile stress state. However, if the critical flaw exists on the compression side of the test specimen, it may not activate to grow a crack and hence the resulting flexural strength will be higher than the true value. The goal of this study is to measure the true flexural strength of a solid or hollow cylindrical brittle specimen by ensuring that failure occurs at its weakest point by rotating along its longitudinal axis, thereby exposing and activating its critical surface flaw during a four-point bend test. A novel test fixture has been designed and fabricated, and the true flexural strengths of cylindrical brittle and quasi-brittle tubular specimens have been measured and compared to existing experimental data obtained through traditional four-point bend tests. In this work, experimental results showcase the orientation dependance on flexural strength for various materials. Additionally, similarities between experimental findings and those available in literature, including observations of fracture surfaces and relationships between surface roughness and material strength, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural evolution and strengthening mechanisms in a heat-treated additively manufactured Al–Cu–Mn–Zr alloy

In this report the microstructural and strength evolution of an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr alloy upon aging at 300, 350, and 400 °C is investigated. The strengthening phases of the alloy evolve significantly upon aging, with breakdown and spheroidization of the interconnected θ-Al 2 Cu network, dissolution of metastable θ'-Al 2 Cu precipitates, and precipitation of nanometric L1 2 -Al 3 Zr from a matrix supersaturated in Zr. In the peak-aged states, the alloy displays a favorable combination of strength and ductility, with a room-temperature yield strength of 314–341 MPa and ductility of 11–13%. The measured yield strengths for microstructures with different aging treatments are compared to predictions of yield strengths from grain boundary, solid solution, and particle strengthening contributions. The observed strain hardening behavior is related to fundamental precipitate and dislocation interactions. Comparison between predicted and measured strength values indicates a continued need for strengthening models specifically developed for the heterogeneous microstructures of additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

An Experimental and Numerical Study of Plasma Treatment Effects on Adhesive Joints of Metals, CFRTPs, and Metal–CFRTP Combinations

This work investigates the effects of plasma surface treatment on both the local adherend–adhesive interfacial strength and the global lap shear strength (LSS) of adhesively-bonded joints composed of metals, CFRTPs, and metal-CFRTP combinations, using AA6061 and CFRPPA as representative examples. Experimental and computational results show that plasma treatment improved the ratio of CFRPPA–adhesive interfacial normal strength to adhesive tensile strength (sint,n/scri,t,adhesive) from 0.59–1.00 to 0.91–1.73, leading to an average 90% increase in LSS for CFRPPA-related joints. In contrast, the LSS and sint,n/scri,t,adhesive values of AA6061–AA6061 joints (>=2.27) remained nearly unchanged after plasma treatment. The enhanced joint bonding was further supported by post-failure surface morphologies from three-dimensional profilometry and simulations, showing a transition from dominant interfacial failure to mixed modes involving interfacial, cohesive, and slight fiber-peeling failures. The LSS evolution with respect to sint,n/scri,t,adhesive was numerically established until the saturation of the LSS of various joints, and the behavior of AA6061–CFRPPA T-joints with varying interfacial strengths was also modeled. This study highlights the importance of local interfacial bonding strength, rather than global LSS, for understanding and optimizing the mechanical performance of adhesively-bonded composite–metal and composite-composite structures via different surface modification strategies.

Qiao, Yao (ORCID:0000000265867604)↗
DOE OSTI2021

Coupling of Flavonoid Initiation Sites with Monolignols Studied by Density Functional Theory

Lignin recalcitrance presents a challenge for the development of a bioeconomy that employs lignocellulosic feedstocks. The efficiency of lignin deconstruction is improved by a reduction of molecular weight, and given the discovery that flavones serve as initiation sites in lignin biosynthesis, these molecular weight reductions could potentially be achieved with plant metabolic engineering to over-express flavonoids. Upon increasing the flavonoid content in lignin, the bond strengths and properties of flavonoid-monolignol linkages become increasingly important. To that end, the current work applies density functional theory calculations to elucidate the bond dissociation enthalpies (BDEs) of flavonoid-monolignol linkages, including dimers with oxidized monolignols. Specifically, the dimer bond strengths and monomer hydrogen abstraction energies for the flavonoids tricin, chrysoeriol, luteolin, apigenin, catechin, epicatechin, epigallocatechin, and epigallocatechin gallate are calculated, when coupled to seven natural and engineered monolignols. Results indicate that 4'-O-ß linkage strengths between flavonoids and monolignols are of comparable strength to inter-monolignol ß-O-4 linkages, with average flavonoid-monolignol BDEs of 70.7 kcal/mol relative to ~69.3 kcal/mol in analogous canonical monolignols. Epigallocatechin yielded the lowest 4'-O-ß bond strength of 52.3 kcal/mol when coupled to an oxidized monolignol, while the flavones overall produced lower average BDEs, relative to the flavanols. Substituents at the 3'-C and 5'-C positions on flavonoids affected the dimer linkage strengths to a greater extent than glycosylation or substituents further from the linkage. Erythro and threo stereochemistry across the flavonoid-monolignol linkage library exhibited only small energetic differences and no pronounced correlations. Taken together, the predictions from this work support the concept that higher concentrations of flavonoid initiation sites in lignin may afford linkage properties conducive to more facile lignin depolymerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Tailoring additive manufacturing to optimize dynamic properties in 316L stainless steel

With the advent of additive manufacturing, manipulation of typical microstructural elements such as grain size, texture, and defect densities is now possible at a faster time scale. While the processing–structure–property relationship in additive manufactured metals has been well studied over the past decade, little work has been done in understanding how this process affects the dynamic behavior of materials. We postulate that additive manufacturing can be used to alter the material microstructure and used to enhance its dynamic strength. In this work, 316L stainless steel (SS) was manufactured via selected laser melting and its microstructure was altered through changing build parameters like laser power, speed, and hatch spacing systematically. These samples were then subjected to spall recovery experiments to measure the spall strength and quantify the amount of damage as a function of build parameters. By mapping the spall strength as a function of build parameters, this work demonstrated that indeed additive manufacturing can be used to tailor the spall strength of 316L SS. This work also determined the optimum build parameters (laser power=195W; scanning speed=1083mm/s; hatch spacing=0.09mm; layer thickness=0.02mm) to obtain the highest spall strength and the least amount of total damage in 316L SS. Microstructural characterization of the pre- and post-mortem samples revealed that increased grain average misorientation and textural index were the main driving force behind this higher spall strength. This work aims to enhance microstructural engineering techniques to design materials with greater resistance to dynamic shock loading.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Measurements of Gamow-Teller transitions from 59 Co via the 59 Co ⁢(𝑡, 3 He +𝛾) charge-exchange reaction and its application to the stellar electron-capture rates

Electron-capture reactions on iron-group nuclei play a crucial role in the late stages of massive star evolution. Since stellar evolution simulations depend on accurate electron-capture rates—which are highly sensitive to the detailed Gamow-Teller (GT) strength distributions—reliable theoretical models are essential. However, experimental data on GT strength distributions are scarce. High-resolution measurements are therefore vital for benchmarking and improving these theoretical calculations. To provide high-resolution data on Gamow-Teller strength distributions of iron-group nuclei and to compare these results with theoretical calculations within this mass region. Differential cross sections for the 59 Co ⁢(𝑡, 3 He)⁢ 59 Fe charge-exchange reaction at 115 MeV/u were measured using the S800 spectrometer. Furthermore, to resolve individual levels that are not distinguishable in the S800 particle singles data, coincident 𝛾 rays from the 59 Fe residual nucleus were detected by using the Gamma-Ray Energy Tracking In-beam Nuclear Array 𝛾-ray tracking array. Here, the Gamow-Teller transition strength distribution from the ground state of 59 Co to 59 Fe was extracted up to an excitation energy of 10 MeV. Additionally, transition strengths for several low-lying states were determined from coincident 𝛾-ray measurements. Electron-capture rates calculated using the present data indicate that these low-lying states contribute significantly to the overall rates in relevant stellar environments. The experimental results show reasonable agreement with theoretical predictions based on both shell-model and projected shell-model calculations. High-resolution data on Gamow-Teller strength distributions—particularly for individual low-lying states—are essential for accurately determining electron-capture rates in iron-group nuclei. Coincident 𝛾-ray measurements provide a powerful tool for obtaining such detailed information. While the present work demonstrates that shell-model calculations successfully reproduce the experimental results, such comparisons are scarce and more experimental data are desirable.

59 ≤ A ≤ 89↗