Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “slots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Near millimeter wave imaging/multi-beam integrated antennas

This report describes the most recent work on the theory of single element Linearly Tapered Slot Antennas (LTSAs) and Constant Width Slot Antennas (CWSAs). The radiation mechanism for these is presently well understood and allows quantitative calculation of beamwidths and sidelobe levels, provided that the antennas have a sufficiently wide conducting region on either side of the tapered slot. Appendices 4 to 7 represent earlier work on the grant. This work further elucidates the properties of arrays of CWSA elements, and the effects of coupling on the beam-shape. It should be noted that typical beam-efficiencies of 65% have been estimated, and that element spacings of about one Rayleigh unit are possible. Further, two-point resolution at the Rayleigh spacing has been demonstrated for a CWSA array in a 30.4 cm paraboloid at 31 GHz. These results underscore that interest in further studies of the radiation mechanism of tapered slot arrays. Appendix 7 constitutes a final, detailed report on the work leading to a 94 GHz seven element LTSA array imaging system, which has been reported previously in less detail. Experimental results are presented.

Yngvesson, K. S.↗
NASA NTRS1986

Verification of performance results for a low-speed 15 percent elliptical circulation control airfoil

Low-speed wind tunnel tests performed by the Naval Ship Research and Development Center (NSRDC) on a circulation control airfoil model was repeated by the Joint Institute for Aerodynamics and Acoustics in an attempt to reproduce the performance results. The model used was a 15% ellipse with interchangeable trailing edges. Surface pressure measurements were taken to obtain lift and pitching moment coefficients as functions of jet blowing momentum, and the momentum deficit in the wake was measured and used to calculate the drag coefficient. The effects of spanwise slot height variation and of leading edge blowing on performance were also investigated. The performance results showed that of the three slot heights tested, a slot height/chord ratio of 0.0022 produced the most lift coefficient for a given blowing rate. Lift obtained in the current test ranged from 2 to 35% lower than the NSRDC test. However, the two data sets compared reasonably well considering wind tunnel and wall blowing scheme differences. The spanwise lift distribution showed less change in lift due to a variation in slot height than expected. The leading edge blowing results demonstrated that although lift initially decreased, a positive lift increment was possible at higher leading edge blowing rates.

Rodman, L. C.↗
NASA NTRS1987

Development of computer models for correlating data of film cooling of nose cone under hypersonic flow

A 12.5 degree half cone with tangential slot injection at Mach 6.95 was studied to determine the heating rates to the surface of the body near and far downstream of the slot. The cone had a zero degree angle of attack. The heating rates were obtained using a computer program that was developed at NASA-Langley Research Center. The concentration of nitrogen from the slot into the boundary layer was also determined. The ratio of slot to freestream was varied to determine its effect on heating. The numerical heating rates were compared to other correlations obtained from experimental studies as well as theoretical laminar and turbulent results.

Sharpe, L., Jr.↗
NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind-tunnel measurements of boundary-layer and wake velocity profiles and surface static-pressure distributions are presented for a swept, circulation-control wing. The model is an aspect-ratio-four semispan wing mounted on the tunnel side wall at a sweep angle of 45 deg. A full-span, tangential, rearward-blowing, circulation-control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary-layer profiles measured on the forward portions of the wing are approximately streamwise and two-dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three-dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near-wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5-deg angle of attack, a range of jet blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower-surface separation location with blowing rate was determined from boundary-layer measurements at Mach 0.425.

Spaid, Frank W.↗
NASA NTRS1987

Airborne tracking sunphotometer apparatus and system

An airborne tracking Sun photometer apparatus has a rotatable dome. An azimuth drive motor is connected to rotate the dome. The dome has an equatorial slot. A cylindrical housing is pivotally mounted inside the dome at the equatorial slot. A photometer is mounted in the housing to move in the equatorial slot as the housing pivots. The photometer has an end facing from the slot with an optical flat transparent window. An elevation drive motor is connected to pivot the cylindrical housing. The rotatable dome is mounted in the bulkhead of an aircraft to extend from the interior of the aircraft. A Sun sensor causes the photometer to track the Sun automatically. Alternatively, the photometer may be oriented manually or by computer.

Matsumoto, Yutaka↗
NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind tunnel measurements of boundary layer and wake velocity profiles and surface static pressure distributions are presented for a swept, circulation control wing. The model is an aspect ratio four semispan wing mounted on the tunnel side wall as a sweep angle of 45 deg. A full span, tangetial, rearward blowing, circulation control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary layer profiles measured on the forward portions of the wing are approximately streamwise and two dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5 deg angle of attack, a range of jet blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower surface separation location with blowing rate was determined from the boundary layer measurements at Mach 0.425.

Spaid, Frank W.↗
NASA NTRS1987

Boundary-layer and wake measurements on a swept, circulation-control wing

Wind-tunnel measurements of boundary-layer and wake velocity profiles and surface static pressure distributions are presented for a swept, circulation-control wing. The model is an aspect-ratio-four semispan wing mounted on the tunnel side wall at a sweep angle of 45 deg. A full-span, tangential, rearward blowing, circulation-control slot is located ahead of the trailing edge on the upper surface. Flow surveys were obtained at mid-semispan at freestream Mach numbers of 0.425 and 0.70. Boundary-layer profiles measured on the forward portions of the wing are approximately streamwise and two dimensional. The flow in the vicinity of the jet exit and in the near wake is highly three dimensional. The jet flow near the slot on the Coanda surface is directed normal to the slot. Near-wake surveys show large outboard flows at the center of the wake. At Mach 0.425 and a 5-deg angle of attack, a range of jet-blowing rates was found for which an abrupt transition from incipient separation to attached flow occurs in the boundary layer upstream of the slot. The variation in the lower-surface separation location with blowing rate was determined from boundary-layer measurements at Mach 0.425.

Spaid, Frank W.↗
NASA NTRS1988

Solar dynamic heat rejection technology. Task 2: Heat pipe radiator development

This report covers the design, fabrication, and test of several dual slot heat pipe engineering development units. The following dual-slot heat pipes were fabricated and tested: two 6-ft. aluminum heat pipes; a 20-ft. aluminum heat pipe; and a 20-ft. aluminum heat pipe with a four-leg evaporator section. The test results of all four test articles are presented and compared to the performance predicted by the design software. Test results from the four-leg article are incomplete. The methodology for fabricating stainless steel dual slot heat pipes was also studied by performing a tool life test with different single point cutters, and these results are also presented. Although the dual-slot heat pipe has demonstrated the potential to meet the requirements for a high capacity radiator system, uncertainties with the design still exist. The startup difficulties with the aluminum test articles must be solved, and a stainless steel/methanol heat pipe should be built and tested.

League, Mark↗
NASA NTRS1988

Acoustical scattering from finite compliant surfaces bounding a duct

Acoustic radiation effects of a finite compliant surface covering a transverse slot in a two-dimensional parallel walled rigid duct are investigated. Radiation from a harmonic source external to the duct is shown to impinge on the slot, reradiating to the half plane and propagating through the duct. Integral equation techniques are employed to study the cases of an open slot, a membrane cover, and a flexible plate cover. The total power radiated to the half plane external to the duct and to the region internal to the duct is determined, taking into account slot-width and fluid-loading variations and the effect of the surface on the power radiated.

Smith, M. E.↗
NASA NTRS1990

Flow visualization studies of blowing from the tip of a swept wing

Flow visualization studies of blowing from the tip of a swept wing were conducted in the Langley 16- by 24-inch water tunnel. Four wing tips, each with two independent blowing slots, were tested. The two slots were located one behind the other in the chordwise direction. The wing tips were designed to vary systematically the jet length, the jet in-plane exhaust direction (sweep), and the jet out-of-plane exhaust direction (anhedral). Each blowing slot was tested separately at two angles of attack and at four ratios of jet to free stream velocity ratios. Limited tests were conducted with blowing from both slots simultaneously. Blowing from the tip inhibited inboard spanwise flow on the upper wing surface near the tip. The jet path moved farther away from the tip with increasing jet to free stream velocity ratio and moved closer to the tip with increasing angle of attack.

Smith, Jeannette W.↗
NASA NTRS1992

Axial-Loading Circumferential Dovetail Turbine-Blade Mount

In new configuration, retaining ring holds base of blades in circumferential dovetail slot. Blades inserted axially via loading slots into circumferential dovetail slot. Ring placed over loading slots and fastened with split ring held by arm of disk. Blades less likely to be shaken loose during operation.

Pierce, Martin J.↗
NASA NTRS1992

Forebody flow control on a full-scale F/A-18 aircraft

A full-scale F/A-18 was tested in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center to measure the effectiveness of pneumatic forebody vortex control devices. By altering the forebody vortex flow, yaw control can be maintained to angles of attack greater than 50 deg. Two forebody vortex control devices were tested: a discrete circular jet and a tangential slot. The tests were conducted for angles of attack between 25 and 50 deg, and angles of sideslip from 0 to +/- 15 deg. The Reynolds number based on wing mean aerodynamic chord ranged from 4.5 x 10 exp 6 to 12.0 x 10 exp 6. The time-averaged side forces and yawing moments, along with both time-averaged and time-dependent pressures on the forebody of the aircraft are presented here for various configurations. Of particular interest was the results that the tangential slot blowing had a greater effect on the yawing moment than the discrete circular jet. Additionally, it was found that blowing very close to the radome apex was not as effective as blowing slightly farther aft on the radome, and that a 16-inch slot was more effective than either an 8- or 48-inch long slot.

Lanser, Wendy R.↗
NASA NTRS1992

Analysis of ignition and flame spreading in the Space Shuttle head-end star grain

A model to analyze the unsteady, multidimensional, turbulent flow in the head-end, star slot section of a solid rocket motor (SRM) during ignition transients is presented. This paper examines the complex interactions between the expanding igniter plume, the flow field within the star slot, the heat transfer to the solid propellant, ignition of the propellant, and subsequent flame spreading across the surface of the grain in the slot. The analysis provides a description of the ignition transient sequence from the onset of igniter flow to complete ignition of the head-end star slot region of the SRM.

Ciucci, A.↗
NASA NTRS1992

An investigation of shock/turbulent boundary layer bleed interactions

A numerical investigation was conducted to determine the effect of bleed on oblique shock wave/turbulent boundary layer interactions. The numerical solution to the compressible Navier-Stokes equations reveal the flow details throughout the interaction zone and inside the normal bleed slot. Results are presented for an incident oblique shock of sufficient strength to cause boundary layer separation in the absence of bleed. Bleed is applied across the shock impingement location over a range of bleed mass flow rates corresponding to different values of plenum pressures. The results indicate a complex flow structure with large variations in both normal and tangential flow velocities across the bleed slot. The flow entrainment into the slot is accompanied by an expansion-compression wave system with a bow shock originating inside the bleed slot. Increasing the bleed mass flow by decreasing the plenum pressure caused an initial decrease then a later increase in the boundary layer momentum and displacement thickness downstream of the interaction.

Hamed, A.↗
NASA NTRS1992

Force production mechanisms of a tangential jet on bodies at high alpha

This work explores the mechanisms by which tangential slot blowing creates forces on a body at a high angle of attack. The study is conducted numerically by solving the three-dimensional, compressible-flow Navier-Stokes equations. A tangent-ogive cylinder configuration is used with the blowing slot located both on the nose and on the cylindrical part of the body. The angle of attack used is 30 deg., the Mach no. is 0.2 and the Reynolds no., based on diameter, is 52,000. Several conclusions were made concerning the physical mechanisms by which the jet interacts with the ambient flowfield to produce a side force: (1) A centrifugal force component is created at the wall due to the momentum of the jet being forced to follow the curvature of the surface. (2) A large amount of vorticity is added to the flowfield by the jet. In the region of the slot, the vorticity has the effect of inducing circulation around the body. Downstream of the slot, the vorticity alters the strength of the nose vortices. (3) The position of the nose vortices can be altered to the jet changing the location of separation. And (4), the jet has the ability to excite unstable behavior producing a global change in the character of the flow.

Font, G. I.↗
NASA NTRS1993

A sensitivity study for pneumatic vortex control on a chined forebody

A study was conducted to assess the sensitivity of yaw control on a chined forebody to the longitudinal location of a blowing slot at the chine edge. In addition, the effects of port blowing were also studied. NASA Langley's thin-layer Navier-Stokes code CFL3D was used to compare flow field characteristics and total yawing moment coefficients for the blowing configurations. Based upon equivalent blowing momentum coefficients, a significant increase in yaw control effectiveness was attained from the forward slot, relative to the aft slot, and port blowing was less effective than either slot blowing configuration.

Boalbey, R. E.↗
NASA NTRS1993

A parametric study of bleed in shock boundary layer interactions

A numerical investigation was conducted to study the effect of bleed configuration on oblique-shock wave/turbulent boundary-layer interactions. Bleed is applied through a normal slot across the shock impingement location. The numerical solution to the compressible Navier-Stokes equations is obtained for the turbulent flow throughout the interaction zone and inside the bleed slot for bleed mass flow rates up to 57 percent of the boundary layer mass flow upstream of the interaction. The results indicate that the bleed slot performance improves as the slot width decreases and the length to width ratio increases. This is reflected as an increase in the bleed discharge coefficient and total pressure, and a reduction in the boundary layer momentum and displacement thickness downstream.

Hamed, A.↗
NASA NTRS1948

Wind-tunnel Investigation of High-lift and Stall-control Devices on a 37 Degree Sweptback Wing of Aspect Ratio 6 at High Reynolds Numbers

Results are presented of an investigation in the Langley 19-foot pressure tunnel of the longitudinal characteristics of a semispan model wing having 37 degrees sweepback of the leading edge, an aspect ratio of 6, and NACA 641-212 airfoil section perpendicular to the 27-percent-chord line. Several types of stall-control devices including extensible round-nose leading-edge flaps, a leading-edge slat, and a drooped leading edge were investigated; partial- and full-span trailing-edge split and double slotted flaps were also tested. In addition, various combinations of the aforementioned leading- and trailing-edge flaps were investigated. The tests covered a range of Reynolds numbers between 2.00 x 10(6) and 9.35 x 10(6). The wing with or without trailing-edge splity of double slotted flap was longitudinally unstable near maximum lift due to tip stalling. The addition of an outboard half-span leading-edge flap or a leading-edge slat to the plain wing or wing with inboard half-span split flaps eliminated tip stalling and resulted in stable moment variations at the stall. The drooped leading edge, on the other hand, was only effective when used in conjunction with an upper-surface fence. The combination of an outboard leading-edge device and inboard half-span double slotted flap resulted in an undesirable loop in the pitching-moment curve near maximum lift in spite of an inboard stall. The loop is attributed to the section characteristics of the double slotted flap. Air-flow surveys behind the wing indicated that a suitably placed horizontal tail would eliminate the loop in the moment curve.

Koven, William↗