SEARCH · Engineering Papers
Results for “scaled testing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Results of the space shuttle vehicle ascent air data system probe calibration test using a 0.07-scale external tank forebody model (68T) in the AEDC 16-foot transonic wind tunnel (IA-310), volume 1
A recalibration of the Space Shuttle Vehicle Ascent Air Data System probe was conducted in the Arnold Engineering Development Center (AEDC) transonic wind tunnel. The purpose was to improve on the accuracy of the previous calibration in order to reduce the existing uncertainties in the system. A probe tip attached to a 0.07-scale External Tank Forebody model was tested at angles of attack of -8 to +4 degrees and sideslip angles of -4 to +4 degrees. High precision instrumentation was used to acquire pressure data at discrete Mach numbers ranging from 0.6 to 1.55. Pressure coefficient uncertainties were estimated at less than 0.0020. Data is given in graphical and tabular form.
Results of the space shuttle vehicle ascent air data system probe calibration test using a 0.07-scale external tank forebody model (68T) in the AEDC 16-foot transonic wind tunnel (IA-310), volume 2
A recalibration of the Space Shuttle Vehicle Ascent Air Data System probe was conducted in the Arnold Engineering and Development Center (AEDC) transonic wind tunnel. The purpose was to improve on the accuracy of the previous calibration in order to reduce the existing uncertainties in the system. A probe tip attached to a 0.07-scale External Tank Forebody model was tested at angles of attack of -8 to +4 degrees and sideslip angles of -4 to +4 degrees. High precision instrumentation was used to acquire pressure data at discrete Mach numbers ranging from 0.6 to 1.55. Pressure coefficient uncertainties were estimated at less than 0.0020. Additional information is given in tabular form.
Wind tunnel and ground static tests of a .094 scale powered model of a modified T-39 lift/cruise fan V/STOL research airplane
Ground static and wind tunnel test of a scale model modified T-39 airplane are reported. The configuration in the nose and replacement of the existing nacelles with tilting lift/cruise fans. The model was powered with three 14 cm diameter tip driven turbopowered simulators. Forces and moments were measured by an internal strain guage balance. Engine simulator thrust and mass flow were measured by calibrated pressure and temperature instrumentation mounted downstream of the fans. The low speed handling qualities and general aerodynamic characteristics of the modified T-39 were defined. Test variables include thrust level and thrust balance, forward speed, model pitch and sideslip angle at forward speeds, model pitch, roll, and ground height during static tests, lift/cruise fan tilt angle, flap and aileron deflection angle, and horizonal stabilizer angle. The effects of removing the landing gear, the lift/cruise fans, and the tail surfaces were also investigated.
Results of aerodynamic heat transfer tests of a 0.0175-scale model of the Rockwell International Space Shuttle Orbiter 139 (model number 22-0) in the NASA/Ames 3.5-foot hypersonic wind tunnel (test OH6)
The results of a hypersonic wind tunnel test program conducted using a 0.0175 scale thin-skin thermocouple model of the Space Shuttle Orbiter to obtain aerodynamic heat transfer data on the Orbiter under simulated reentry conditions were presented. The test program was conducted at a Mach number of 7.3 and a freestream Reynolds number ranging between 1.0 and 6.0 million/foot. The model was tested for angles of attack ranging between 10 deg and 30 deg and a sideslip angle of 0 deg. The model was constructed of 15-5 PH stainless steel with the instrumented areas machined to a nominal skin thickness of 0.030 in. The model instrumentation consisted of 288 iron-constantan thermocouples spot welded to the skin inner surface, but only 75 of these were used in this test program. A high-speed, analog-to-digital data acquisition system was used to record data on magnetic tape.
Flow Visualization for Plume-Surface Interaction Testing Within Large-Scale Vacuum Environments at Conditions Relevant to Lunar and Martian Landers
Interactions between rocket exhaust plumes and the landing surface during powered spacecraft descent on the Moon and Mars pose significant risks to the landing vehicle, landing site, and nearby infrastructure. Understanding the underlying plume-surface interaction phenomena through ground test data can provide critical insights on the sensitivities of parameters such as the spacecraft altitude and thrust. In the present work, we summarize a scaled ground test recently conducted within a 20-ft vacuum chamber environment located in the historical East Test Area at the NASA Marshall Space Flight Center. The ground test featured a Mach 5.3 inert gas plume impinging upon an instrumented flat plate. Planar laser-induced fluorescence, which is a 2D laser-based flow field measurement technique, was performed at this test area for the first time to visualize salient flow features such as the barrel shock, stagnation shock, and wall jet. Measurements were obtained at discrete lander altitudes, made dimensionless using the nozzle exit diameter, corresponding to h/D = 10, 8, 5, 4, 3, and 2. The stagnation pressures of the plume were varied from approximately 0.04 to 1 MPa, providing sensitivity to the engine thrust of a powered spacecraft. The unique test facility allowed for near-lunar conditions to be obtained at initial vacuum chamber pressures less than 0.1 Pa. Martian-relevant measurements were also performed at ambient pressures near 600 Pa. Furthermore, a third set of measurements were obtained at so called lunar-relevant conditions near 3 Pa chamber pressure
Flow Visualization for Plume-Surface Interaction Testing Within Large-Scale Vacuum Environments at Conditions Relevant to Lunar and Martian Landers
Interactions between rocket exhaust plumes and the landing surface during powered spacecraft descent on the Moon and Mars pose significant risks to the landing vehicle, landing site, and nearby infrastructure. Understanding the underlying plume-surface interaction phenomena through ground test data can provide critical insights on the sensitivities of parameters such as the spacecraft altitude and thrust. In the present work, we summarize a scaled ground test recently conducted within a 20-ft vacuum chamber environment located in the historical East Test Area at the NASA Marshall Space Flight Center. The ground test featured a Mach 5.3 inert gas plume impinging upon an instrumented flat plate. Planar laser-induced fluorescence, which is a 2D laser-based flow field measurement technique, was performed at this test area for the first time to visualize salient flow features such as the barrel shock, stagnation shock, and wall jet. Measurements were obtained at discrete lander altitudes, made dimensionless using the nozzle exit diameter, corresponding to h/D = 10, 8, 5, 4, 3, and 2. The stagnation pressures of the plume were varied from approximately 0.04 to 1 MPa, providing sensitivity to the engine thrust of a powered spacecraft. The unique test facility allowed for near-lunar conditions to be obtained at initial vacuum chamber pressures less than 0.1 Pa. Martian-relevant measurements were also performed at ambient pressures near 600 Pa. Furthermore, a third set of measurements were obtained at so called lunar-relevant conditions near 3 Pa chamber pressure.
Fin loads and control-surface hinge moments measured in full-scale wind-tunnel tests on the X-24A flight vehicle
Fin loads and control surface hinge moments measured in full scale wind tunnel tests on X-24A flight vehicle
Thrust performance of a variable-geometry, divergent exhaust nozzle on a turbojet engine at altitude
A variable geometry, low aspect ratio, nonaxisymmetric, two dimensional, convergent-divergent exhaust nozzle was tested at simulated altitude on a turbojet engine to obtain baseline axial, dry thrust performance over wide ranges of operating nozzle pressure ratios, throat areas, and internal expansion area ratios. The thrust data showed good agreement with theory and scale model test results after the data were corrected for seal leakage and coolant losses. Wall static pressure profile data were also obtained and compared with one dimensional theory and scale model data. The pressure data indicate greater three dimensional flow effects in the full scale tests than with models. The leakage and coolant penalties were substantial, and the method to determine them is included.
Dynamic scaling for earth based testing of Mars terminal descent dynamics
The purpose of this paper is to outline the derivation and limitations of a dynamic scaling law for Earth based testing of this type of Mars terminal descent system.
Large-Scale Wind-Tunnel Tests of a Wingless Vertical Take-Off and Landing Aircraft: Preliminary Results
Large-scale wind-tunnel tests were made of a wingless vertical take-off and landing aircraft at zero sideslip to determine performance and longitudinal stability and control characteristics at airspeeds from 0 to 70 knots. Roll control and rudder effectiveness were also obtained. Limitations in the propulsion system restricted the lift for which level flight could be simulated to approximately 1500 pounds. Test variables with roll control and rudder undeflected were airspeed, vane setting, angle of attack, elevator deflection, and power. In most of the tests angle of attack, elevator, and power were varied individually while the other four parameters were held constant at previously determined values required for simulating trimmed level flight. The majority of the tests were made with power on and tail on at airspeeds between 20 and 70 knots. However, a limited number of data were obtained for the following conditions: (1) at zero velocity, horizontal tail on, power on; (2) at forward velocity, tail off and power on; and (3) at forward velocity, tail on, but with power off.
Full-Scale Wind-Tunnel Tests of Blowing Boundary-Layer Control Applied to a Helicopter Rotor
A full-scale wind-tunnel test was conducted of two boundary-layer-control applications to a 44-foot diameter helicopter rotor. Blowing from a nozzle near the leading edge of the blades delayed retreating blade stall. Results also indicated that delay of retreating blade stall could be obtained by cyclic blowing with a lower flow rate than that required for continuous blowing. It was found that blowing applied through a nozzle at mid-chord had no effect on retreating blade stall.
Development of airframe design technology for crashworthiness.
This paper describes the NASA portion of a joint FAA-NASA General Aviation Crashworthiness Program leading to the development of improved crashworthiness design technology. The objectives of the program are to develop analytical technology for predicting crashworthiness of structures, provide design improvements, and perform full-scale crash tests. The analytical techniques which are being developed both in-house and under contract are described, and typical results from these analytical programs are shown. In addition, the full-scale testing facility and test program are discussed.
Large-Scale Wind-Tunnel Tests of an Airplane Model with an Unswept, Tilt Wing of Aspect Ratio 5.5, and with Four Propellers and Blowing Flaps
Tests were made of a large-scale tilt-wing deflected-slipstream VTOL airplane with blowing-type BLC trailing-edge flaps. The model was tested with flap deflections of 0 deg. without BLC, 50 deg. with and without BLC, and 80 deg. with BLC for wing-tilt angles of 0, 30, and 50 deg. Included are results of tests of the model equipped with a leading-edge flap and the results of tests of the model in the presence of a ground plane.
Methods for data reduction and loads analysis of Space Shuttle Solid Rocket Booster model water impact tests
The methodology used to predict full scale space shuttle solid rocket booster (SRB) water impact loads from scale model test data is described. Tests conducted included 12.5 inch and 120 inch diameter models of the SRB. Geometry and mass characteristics of the models were varied in each test series to reflect the current SRB baseline configuration. Nose first and tail first water entry modes were investigated with full-scale initial impact vertical velocities of 40 to 120 ft/sec, horizontal velocities of 0 to 60 ft/sec., and off-vertical angles of 0 to plus or minus 30 degrees. The test program included a series of tests with scaled atmospheric pressure.
A History of Full-Scale Aircraft and Rotorcraft Crash Testing and Simulation at NASA Langley Research Center
This paper summarizes 2-1/2 decades of full-scale aircraft and rotorcraft crash testing performed at the Impact Dynamics Research Facility (IDRF) located at NASA Langley Research Center in Hampton, Virginia. The IDRF is a 240-ft.-high steel gantry that was built originally as a lunar landing simulator facility in the early 1960's. It was converted into a full-scale crash test facility for light aircraft and rotorcraft in the early 1970 s. Since the first full-scale crash test was preformed in February 1974, the IDRF has been used to conduct: 41 full-scale crash tests of General Aviation (GA) aircraft including landmark studies to establish baseline crash performance data for metallic and composite GA aircraft; 11 full-scale crash tests of helicopters including crash qualification tests of the Bell and Sikorsky Advanced Composite Airframe Program (ACAP) prototypes; 48 Wire Strike Protection System (WSPS) qualification tests of Army helicopters; 3 vertical drop tests of Boeing 707 transport aircraft fuselage sections; and, 60+ crash tests of the F-111 crew escape module. For some of these tests, nonlinear transient dynamic codes were utilized to simulate the impact response of the airframe. These simulations were performed to evaluate the capabilities of the analytical tools, as well as to validate the models through test-analysis correlation. In September 2003, NASA Langley closed the IDRF facility and plans are underway to demolish it in 2007. Consequently, it is important to document the contributions made to improve the crashworthiness of light aircraft and rotorcraft achieved through full-scale crash testing and simulation at the IDRF.
Post-test data report for the space shuttle full-scale AFRSI sequence of environments test (OS-305-1 to -5) in the NASA/Ames Research Center 11x11-foot wind tunnel
The Advanced Flexible Reusable Surface Insulation (AFRSI) test article was wind tunnel tested. The AFRSI was exposed to a simulated ascent airloads environment and data was obtained which could be used to support the AFRSI certification program. The AFRSI sequence of environments also included radiant heating (1500 degrees Fahrenheit) and wind/rain environments. The test article was wind/rain conditioned before each wind tunnel entry and was thermally conditioned after each wind tunnel entry. The AFRSI failed and the test was aborted before reaching the ascent environment. The AFRSI test article sequentially exposed to 50 wind/rain and 49 simulated entry thermal missions, as well as four wind tunnel entries equivalent to 40 ascent missions.
Experimental study of main rotor tip geometry and tail rotor interactions in hover. Volume 1. Text and figures
A model scale hover test was conducted in the Sikorsky Aircraft Model rotor hover Facility to identify and quantify the impact of the tail rotor on the demonstrated advantages of advanced geometry tip configurations. The test was conducted using the Basic Model Test Rig and two scaled main rotor systems, one representing a 1/5.727 scale UH-60A BLACK HAWK and the others a 1/4.71 scale S-76. Eight alternate rotor tip configurations were tested, 3 on the BLACK HAWK rotor and 6 on the S-76 rotor. Four of these tips were then selected for testing in close proximity to an operating tail rotor (operating in both tractor and pusher modes) to determine if the performance advantages that could be obtained from the use of advanced geometry tips in a main rotor only environment would still exist in the more complex flow field involving a tail rotor. The test showed that overall the tail rotor effects on the advanced tip configurations tested are not substantially different from the effects on conventional tips.