SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Double hook latch provides preloading and support capability up to 80,000 pounds and opens self-energizingly when restraint linkage is released. It incorporates a double hook latch held closed by a toggle linkage attached to a flexible cable rigged in tension.
Four-square gear test rigs, master gear arrangements, and wear rate measurements for instrument sized gears
Design of segmented, axially conducting, pyrolytic graphite rig engine, including thermal and structural analyses
Literature survey, analytic formulations, and test rig designs for cavitating inducers in rocket engine turbopumps
Separate component test rigs for 90 degree sector combustor and full annular turbojet combustor comparison
Determining feasibility of increasing stator blade loading of single stage compressor rig by bleeding or blowing suction surface boundary layer
Burner rig tests on simulated turbine blades, with and without internal cooling, to predict thermal fatigue performance
Aerodynamic and deployment characteristics of twin keel all-flexible parawing rigged with several variations of multistage canopy and suspension line reefing system
Electron beam vapor deposited CoCrAlY coating composition optimization with ballistic impact and furnace/long term burner rig oxidation tests
A study of compressor noise is presented, based upon supersonic, part-speed operation of a high hub/tip ratio compressor designed for spanwise uniformity of aerodynamic conditions, having straight cylindrical inlet and exit passages for acoustic simplicity. Acoustic spectra taken in the acoustically-treated inlet plenum, are presented for five operating points at each of two speeds, corresponding to relative rotor tip Mach numbers of about 1.01 and 1.12 (60 and 67 percent design speed). These spectra are analyzed for low and high frequency broadband noise, blade passage frequency noise, combination tone noise and "haystack' noise (a very broad peak somewhat below blade passage frequency, which is occasionally observed in engines and fan test rigs). These types of noise are related to diffusion factor, total pressure ratio, and relative rotor tip Mach number. Auxiliary measurements of fluctuating wall static pressures and schlieren photographs of upstream shocks in the inlet are also presented and related to the acoustic and performance data.
The application and use of inlets and nozzles in aerospace, V/STOL, and hypersonic propulsion systems are discussed. Data cover test techniques and facilities, experimental results from small rig tests to flight tests, and theoretical analysis of propulsion system flows. The problems associated with such a system are also discussed.
The development of a 10-channel rotating pressure measuring system capable of operation to speeds of 9000 rpm at transducer temperatures of about 320 K (120 F) is described. Variable-reluctance pressure transducers were mounted in the rotating system for sensing pressure. Rotating performance tests on a spin rig showed that the output data from 7 of the 10 transducers tested were within a desired system error of 3 percent. However, the error of the output data from three other transducers was as large as 8 percent of 9000 rpm. It was concluded from these test results that a rotating screening method was necessary to evaluate each pressure transducer channel within a system that will be used under rotating conditions.
The primary aim of this investigation was verification of basic methods which are to be used in cataloging elastomer dynamic properties (stiffness and damping) in terms of viscoelastic model constants. These constants may then be used to predict dynamic properties for general elastomer shapes and operating conditions, thereby permitting optimum application of elastomers as energy absorption and/or energy storage devices in the control of vibrations in a broad variety of applications. The efforts reported involved: (1) literature search; (2) the design, fabrication and use of a test rig for obtaining elastomer dynamic test data over a wide range of frequencies, amplitudes, and preloads; and (3) the reduction of the test data, by means of a selected three-element elastomer model and specialized curve fitting techniques, to material properties. Material constants thus obtained have been used to calculate stiffness and damping for comparison with measured test data. These comparisons are excellent for a number of test conditions and only fair to poor for others. The results confirm the validity of the basic approach of the overall program and the mechanics of the cataloging procedure, and at the same time suggest areas in which refinements should be made.
An abradable buffered labyrinth seal for the control of turbine gas path leakage in a tip-turbine driven lift fan was designed, tested, and analyzed. The seal configuration was not designed to operate in any specific location but was sized to be evaluated in an existing test rig. The final sealing diameter selected was 28 inches. Results of testing indicate that the flow equations predicted seal air flows consistent with measured values. Excellent sealing characteristics of the abradable coating on the stator land were demonstrated when a substantial seal penetration of .030 inch into the land surface was encountered without appreciable wear on the labyrinth knife edges.
A survey is presented of the cyclic furnace and burner rig oxidation facilities at NASA-Lewis Research Center together with a review of selected test results and an initial interpretation of the data obtained. Cyclic furnace tests are used to conveniently screen alloy oxidation resistance and spall tendency; high velocity tests further indicate dynamic environmental resistance. Alloys which form scales predominantly of Cr2O3/chromite spinel spall much more than those forming alpha Al2O3/aluminate spinel scales. Weight changes due to scale spalling were used to estimate alloy depletion/thickness losses.
High speed helicopter transmission seal concepts were designed, fabricated and tested. The concepts were a dual element split ring seal and a circumferential seal. The tests were performed in a rig using an actual input quill assembly. The test conditions were selected to simulate transmission operation and were 230 F oil temperature, and a sliding speed of 9400 ft/min. The split ring seal exhibited gross leakage and was considered unsatisfactory, while the circumferential seal leakage was less than 1 c.c./hour; this leakage is within acceptable limits. The circumferential seal wear was only to .0005 inches during a 100 hour run (40 starts and stops). During a 40 hour contamination test (mesh silica flour) the seal total wear was a maximum of .004 inches. This wear is considered acceptable.
A design integration study program was conducted to determine size and performance parameters of an augmentor wing cruise blowing (valveless) system in a 150-passenger STOL airplane for the purpose of defining size and configuration of static rig, flow duct, and wind tunnel test hardware. The studies encompassed blowing systems powered by low-pressure (single stage) and high-pressure (three and four stage) engine fans. A range of wing aspect ratios, wing thicknesses, and duct flow velocity effects were investigated to establish airplane characteristics which minimize takeoff gross weight while achieving sideline noise requirements for an advanced commercial STOL airplane.
Foil bearings were designed and manufactured to replace pivoted-shoe journal bearings in an existing Brayton Cycle turbo-alternator-compressor. The design of this unconventional rotor support was accomplished within the constraints and space limitations imposed by the present machine, and the substitution of foil bearings was effected without changes or modification other machine components. A housing and a test rig were constructed to incorporate the new foil-bearing support into a unified assemble with an air-driven rotor and the gimbal-mounted thrust bearing, seals, and shrouds of an actual Brayton Rotating Unit. The foil bearing required no external pressure source, and stable self-acting rotation was achieved at all speeds up to 43,200 rpm. Excellent wipe-wear characteristics of the foil bearing permitted well over 1000 start-stop cycles with no deterioriation of performance in the entire speed range.