Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Drag coefficient equations for small particles in high speed flows

The paper determines the effect of various available drag coefficient equations on particle velocity calculations for typical two phase flows encountered in supersonic and turbulent laser velocimeter applications. The predictions of the particle drag coefficient equations are compared with experimental sphere drag data. For the laser velocimeter applications, the relative Mach number less than 2 and the relative Reynolds number less than 200 are of particular importance.

Walsh, M. J.↗

A description of the University of Illinois meteor radar system and some first results

A recently established meteor radar system for observing motions in the upper atmosphere is described, which features a peak transmitter power of 5 megawatts. This large peak power should allow a much greater number of wind determination during a fixed period of time than other meteor radar stations. The essential features of the range algorithm, two velocity algorithms, and the interferometer phase difference algorithm in use are described. A typical measured variation in the radial southward wind as a function of time of day based on data from all altitudes is shown as an example, and some results of spectral analysis of the data, yielding amplitude and phase variation with altitude for significant waves, is discussed.

Geller, M. A.↗

The structure of a separating turbulent boundary layer. IV - Effects of periodic free-stream unsteadiness

Measurements were obtained of the sinusoidal unsteadiness of the free stream velocity during the separation of the turbulent boundary layer. Data were gathered by single wire and cross-wire, anemometry upstream of flow detachment, by laser Doppler velocimetry to detect the movement of the flow in small increments, and by a laser anemometer in the detached zone to measure turbulence and velocities. The study was restricted to a sinusoidal instability frequency of 0.61 and a ratio of oscillation amplitude to mean velocity of 0.3. Large amplitude and phase variations were found after the detachment, with unsteady effects producing hysteresis in the relationships between flow parameters. The detached shear layer decreased in thickness with increasing free-stream velocity and increases in the Reynolds shear stress. Deceleration of the free stream velocity caused thickening in the shear layer and upstream movement of the flow reversal location. The results are useful for studies of compressor blade and helicopter rotors in transition.

Simpson, R. L.↗

The preferred-mode coherent structure in the near field of an axisymmetric jet with and without excitation

Visualization and phase-locked hot-wire measurements have been used to investigate the preferred-mode coherent structure in the near field of an axisymmetric jet for different Reynolds numbers and for the two limiting asymptotic states of the exit boundary layer: laminar and fully developed turbulent. Distributions of phase-averaged longitudinal and lateral velocities, coherent vorticity, coherent and incoherent turbulence Reynolds stresses, and coherent strain rate and production have been obtained over the spatial extent of the coherent structure for a Strouhal number of 0.3. It is found that these properties are independent of the initial conditions, but weakly dependent on the Reynolds number up to about 100,000. The naturally occurring coherent structure in the unexcited jet, educed via an optimized conditional sampling scheme, shows no clear dependence on the jet Reynolds number up to 800,000.

Hussain, A. K. M. F.↗

Acoustic imaging of subtle porosity variations in ceramics

Acoustic images of silicon carbide ceramic disks were obtained using a precision scanning contact pulse-echo technique. Phase and cross-correlation velocity and attenuation maps were used to form color images of microstructural variations. These acoustic images reveal microstructural variations not observable with X-radiography.

Generazio, E. R.↗

Buoyancy effects on morphological instability during directional solidification

The onset of morphological instability during the directional solidification of a single-phase binary alloy at constant velocity vertically upwards is treated by a linear stability analysis. The case in which a heavier solute is rejected at the solidifying interface is considered, and the effect of natural convection on the critical concentration for the onset of instability is studied. For tin containing lead, a small destabilization of the system at low growth velocities, and a large increase in the wavelength of the instability at the onset are found. Calculations show that the destabilization is enhanced as the variation of density with solute concentration is reduced, and in the limit of neutrally-dense solute, there is a long wavelength instability for which the critical solute concentration is several orders of magnitude lower than that predicted by the Mullins and Sekerka (1964) analysis in the absence of convection. For the neutrally-dense solute, a simplified analysis indicates the roles played by the interface deformation and thermal convection in promoting the instability. In particular, the destabilization is very sensitive to the ratio of crystal and melt thermal conductivities.

Coriell, S. R.↗

Disintegration of liquid sheets

The development, stability, and disintegration of liquid sheets issuing from a two-dimensional air-assisted nozzle is studied. Detailed measurements of mean drop size and velocity are made using a phase Doppler particle analyzer. Without air flow the liquid sheet converges toward the axis as a result of surface tension forces. With airflow a quasi-two-dimensional expanding spray is formed. The air flow causes small variations in sheet thickness to develop into major disturbances with the result that disruption starts before the formation of the main break-up region. In the two-dimensional variable geometry air-blast atomizer, it is shown that the air flow is responsible for the formation of large, ordered, and small chaotic 'cell' structures.

Mansour, Adel↗

Low Mach number parallel and quasi-parallel shocks

The properties of low-Mach-number parallel and quasi-parallel shocks are studied using the results of one-dimensional hybrid simulations. It is shown that both the structure and ion dissipation at the shocks differ considerably. In the parallel limit, the shock remains coupled to the piston and consists of large-amplitude magnetosonic-whistler waves in the upstream, through the shock and into the downstream region, where the waves eventually damp out. These waves are generated by an ion beam instability due to the interaction between the incident and piston-reflected ions. The excited waves decelerate the plasma sufficiently that it becomes stable far into the downstream. The increase in ion temperature along the shock normal in the downstream region is due to superposition of incident and piston-rflected ions. These two populations of ions remain distinct through the downstream region. While they are both gyrophase-bunched, their counterstreaming nature results in a 180-deg phase shift in their perpendicular velocities.

Omidi, N.↗

Structure of confined laminar spray diffusion flames: Numerical investigation

The structure of confined laminar spray diffusion flames is investigated numerically by solving the gas-phase conservation equations for mass species, continuity, momentum, and energy and the liquid-phase equations for droplet position, velocity, size, and temperature. A one-step global reaction scheme along with six equilibrium reactions are employed to model the flame chemistry. Monodisperse as well as polydisperse sprays are considered. The numerical results demonstrate that liquid spray flames substantially differ from gaseous flames in their structure, i.e., temperature, concentration, and velocity fields, shape, and dimensions under the same conditions. Spray flames are predicted to be taller and narrower than their counterpart gaseous ones and their shapes are almost cylindrical. This is in agreement with experimental observations. The numerical computations also show that the use of the equilibrium reactions with the one-step reaction scheme decreases the flame temperature compared to the one-step reaction scheme without the equilibrium reactions and more importantly increases the surface area of the flame zone due to a phenomenon termed 'equilibrium broadening.' The spray flames also possess a finite thickness with minimal overlap of the fuel and oxygen species. A case for which a fuel-mixture consisting of 20 to 80 percent gas-liquid by mass is introduced into the combustor is also investigated and compared with predictions using only gaseous or liquid fuel.

Mawid, M. A.↗

Rossby-gravity waves in tropical total ozone data

Evidence for Rossby-gravity waves in tropical data fields produced by the European Center for Medium Range Weather Forecasts (ECMWF) was recently reported. Similar features are observable in fields of total column ozone from the Total Ozone Mapping Spectrometer (TOMS) satellite instrument. The observed features are episodic, have zonal (east-west) wavelengths of 6,000-10,000 km, and oscillate with periods of 5-10 days. In accord with simple linear theory, the modes exhibit westward phase progression and eastward group velocity. The significance of finding Rossby-gravity waves in total ozone fields is that (1) the report of similar features in ECMWF tropical fields is corroborated with an independent data set and (2) the TOMS data set is demonstrated to possess surprising versatility and sensitivity to relatively smaller scale tropical phenomena.

Stanford, J. L.↗

Secondary atomization in the combustion of electrostatic sprays

The combustion of electrosprays in a laminar counterflow diffusion flame has been experimentally studied by measuring droplet size and velocity distributions and gas-phase temperature. Detailed examination of the evolution of droplet size distribution as droplets approach the flame shows that, if substantial evaporation occurs before droplets 'interact' with the flame, the size distribution becomes bimodal. A secondary, sharp peak, in fact, develops in correspondence of diameters about one order of magnitude smaller than the mean. No evaporation mechanism can account for the development of such bimodality, that can be explained only in terms of a disintegration of droplets into finer fragments of size much smaller than the parent ones. This fission is of electric nature and it occurs when the repulsion of electric charges overcomes the surface tension cohesive force ultimately leading to a disintegration into finer fragments at or about the so-called Rayleigh limit. We here report on the first observation in combustion environments of such 'explosions'. If, on the other hand, droplets enter the very high temperature region before exploding, there appears to be no evidence of bimodality in their size distribution. In this case, in fact, flame chemi-ions may neutralize the charge on the droplets and thus prevent disruption.

Gomez, Alessandro↗

Microspheres for laser velocimetry in high temperature wind tunnel

The introduction of non-intrusive measurement techniques in wind tunnel experimentation has been a turning point in error free data acquisition. Laser velocimetry has been progressively implemented and utilized in various wind tunnels; e.g. subsonic, transonic, and supersonic. The success of the laser velocimeter technique is based on an accurate measurement of scattered light by seeding particles introduced into the flow stream in the wind tunnel. Therefore, application of appropriate seeding particles will affect, to a large extent the acquired data. The seeding material used depends on the type of experiment being run. Among the seeding material for subsonic tunnel are kerosene, Kaolin, and polystyrene. Polystyrene is known to be the best because of being solid particles, having high index of refraction, capable of being made both spherical and monodisperse. However for high temperature wind tunnel testing seeding material must have an additional characteristic that is high melting point. Typically metal oxide powders such as Al2O3 with melting point 3660 F are used. The metal oxides are, however polydispersed, have a high density, and a tendency to form large agglomerate that does not closely follow the flow velocity. The addition of flame phase silica to metal oxide helps to break up the agglomerates, yet still results in a narrow band of polydispersed seeding. The less desirable utility of metal oxide in high temperature wind tunnels necessitates the search for a better alternative particle seeding which this paper addresses. The Laser Velocimetry (LV) characteristic of polystyrene makes it a prime candidate as a base material in achieving the high temperature particle seeding inexpensively. While polystyrene monodisperse seeding particle reported has been successful in a subsonic wind tunnel, it lacks the high melting point and thus is not practically usable in a high temperature wind tunnel. It is well known that rise in melting point of polystyrene can be achieved by a cross-linking technique. Since polystyrene already possesses all the desired characteristics for LV, to circumvent the low melting point, a cross-linking technique was investigated.

Ghorieshi, Anthony↗

Rossby-gravity waves in tropical total ozone

Randel (1992) has recently reported evidence for Rossby-gravity waves in tropical data fields produced by the European Centre for Medium Range Weather Forecasts (ECMWF). The purpose of this paper is to show that similar features are observable in fields of total column ozone from the Total Ozone Mapping Spectrometer (TOMS) satellite instrument. The observed features are episodic, have zonal (east-west) wavelengths of approximately 6,000-10,000 km and oscillate with periods of 5-10 days. The modes exhibit westward phase progression and eastward group velocity. A simple linear model is used to estimate the magnitude of total ozone perturbations induced by Rossby-gravity waves. The model is able to account for the magnitude of observed TOMS features as well as their asymmetry about the equator. The significance of finding Rossby-gravity waves in total ozone fields is that: (1) the report of similar features in ECMWF tropical fields is corroborated with an independent data set; and (2) the TOMS data set is demonstrated to possess surprising versatility and sensitivity to relatively smaller scale tropical phenomena.

Stanford, J. L.↗

Forced and Free Intra-Seasonal Variability Over the South Asian Monsoon Region Simulated by 10 AGCMs

This study examines intra-seasonal (20-70 day) variability in the South Asian monsoon region during 1997/98 in ensembles of 10 simulations with 10 different atmospheric general circulation models. The 10 ensemble members for each model are forced with the same observed weekly sea surface temperature (SST) but differ from each other in that they are started from different initial atmospheric conditions. The results show considerable differences between the models in the simulated 20-70 day variability, ranging from much weaker to much stronger than the observed. A key result is that the models do produce, to varying degrees, a response to the imposed weekly SST. The forced variability tends to be largest in the Indian and western Pacific Oceans where, for some models, it accounts for more than 1/4 of the 20-70 day intra-seasonal variability in the upper level velocity potential during these two years. A case study of a strong observed MJO (intraseasonal oscillation) event shows that the models produce an ensemble mean eastward propagating signal in the tropical precipitation field over the Indian Ocean and western Pacific, similar to that found in the observations. The associated forced 200 mb velocity potential anomalies are strongly phase locked with the precipitation anomalies, propagating slowly to the east (about 5 m/s) with a local zonal wave number two pattern that is generally consistent with the developing observed MJO. The simulated and observed events are, however, approximately in quadrature, with the simulated response 2 leading by 5-10 days. The phase lag occurs because, in the observations, the positive SST anomalies develop upstream of the main convective center in the subsidence region of the MJO, while in the simulations, the forced component is in phase with the SST. For all the models examined here, the intraseasonal variability is dominated by the free (intra-ensemble) component. The results of our case study show that the free variability has a predominately zonal wave number one pattern, and has propagation speeds (10 - 15 m/s) that are more typical of observed MJO behavior away from the convectively active regions. The free variability appears to be synchronized with the forced response, at least, during the strong event examined here. The results of this study support the idea that coupling with SSTs plays an important, though probably not dominant, role in the MJO. The magnitude of the atmospheric response to the SST appears to be in the range of 15% - 30% of the 20-70 day variability over much of the tropical eastern Indian and western Pacific Oceans. The results also highlight the need to use caution when interpreting atmospheric model simulations in which the prescribed SST resolve MJO time scales.

Wu, Man Li C.↗

3-D Flow Field Diagnostics and Validation Studies using Stereoscopic Tracking Velocimetry

The measurement of 3-D three-component velocity fields is of great importance in both ground and space experiments for understanding materials processing and fluid physics. Here, we present the investigation results of stereoscopic tracking velocimetry (STV) for measuring 3-D velocity fields. The effort includes diagnostic technology development, experimental velocity measurement, and comparison with analytical and numerical computation. The advantages of STV stems from the system simplicity for building compact hardware and in software efficiency for continual near-real-time process monitoring. It also has illumination flexibility for observing volumetric flow fields from arbitrary directions. STV is based on stereoscopic CCD observations of particles seeded in a flow. Neural networks are used for data analysis. The developed diagnostic tool is tested with a simple directional solidification apparatus using Succinonitrile. The 3-D velocity field in the liquid phase is measured and compared with results from detailed numerical computations. Our theoretical, numerical, and experimental effort has shown STV to be a viable candidate for reliably quantifying the 3-D flow field in materials processing and fluids experiments.

Cha, Soyoung Stephen↗

3D Simulations of the Richtmyer-Meshkov Instability with Re-Shock

We present results of inviscid simulations, in three dimensions, of Richtmyer-Meshkov instability for high incident shock Mach number. The growth rate of a single harmonic perturbation is quantified and compared with the results of a 2D calculation. Upon re-shock, the perturbation amplitude undergoes a phase reversal while the mean velocity of the interface is zero. Before re-shock the normalized growth rate of a 2D and 3D interface are nearly the same, but the growth rate after re-shock is significantly larger for the 3D than the 2D case. We also examine the evolution of multiple harmonic perturbations. Computational and parallelization issues of the simulation code will also be briefly discussed. The computations were done on the T3E at Pittsburgh Supercomputing Center.

Meiron, Daniel I.↗

The Collapse of Vapor Bubbles in a Spatially Non-Uniform Flow

Pressure gradients act differently on liquid particles and suspended bubbles and are, therefore, capable of inducing a relative motion between the phases even when no relative velocity initially exists. As a consequence of the enhanced heat transfer in the presence of convection, this fact may have a major impact on the evolution of a vapor bubble. The effect is particularly strong in the case of a collapsing bubble for which, due to the conservation of the system's impulse, the induced relative velocity tends to be magnified when the bubble volume shrinks. A practical application could be, for instance, the enhancement of the condensation rate of bubbles downstream of a heated region, thereby reducing the quality of a flowing liquid-vapor mixture. A simple model of the process, in which the bubble is assumed to be spherical and the flow potential, is developed in the paper.

Hao, Y.↗

Effects of Lewis Number on Temperatures of Spherical Diffusion Flames

Spherical diffusion flames supported on a porous sphere were studied numerically and experimentally. Experiments were performed in 2.2 s and 5.2 s microgravity facilities. Numerical results were obtained from a Chemkin-based program. The program simulates flow from a porous sphere into a quiescent environment, yields both steady-state and transient results, and accounts for optically thick gas-phase radiation. The low flow velocities and long residence times in these diffusion flames lead to enhanced radiative and diffusive effects. Despite similar adiabatic flame temperatures, the measured and predicted temperatures varied by as much as 700 K. The temperature reduction correlates with flame size but characteristic flow times and, importantly, Lewis number also influence temperature. The numerical results show that the ambient gas Lewis number would have a strong effect on flame temperature if the flames were steady and nonradiating. For example, a 10% decrease in Lewis number would increase the steady-state flame temperature by 200 K. However, for these transient, radiating flames the effect of Lewis number is small. Transient predictions of flame sizes are larger than those observed in microgravity experiments. Close agreement could not be obtained without either increasing the model s thermal and mass diffusion properties by 30% or reducing mass flow rate by 25%.

Santa, K. J.↗