Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “patterned beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Monitoring of the MU radar antenna pattern by Satellite Ohzora (EXOS-C)

As the first attempt among MST (mesosphere stratosphere troposphere) type radars, the MU (middle and upper atmosphere) radar features an active phased array system. Unlike the conventional large VHF radars, in which output power of a large vacuum tube is distributed to individual antenna elements, each of 475 solid state power amplifier feeds each antenna element. This system configuration enables very fast beam steering as well as various flexible operations by dividing the antenna into independent subarrays, because phase shift and signal division/combination are performed at a low signal level using electronic devices under control of a computer network. The antenna beam can be switched within 10 microsec to any direction within the zenith angle of 30 deg. Since a precise phase alignment of each element is crucial to realize the excellent performance of this system, careful calibration of the output phase of each power amplifier and antenna element was carried out. Among various aircraft which may be used for this purpose artificial satellites have an advantage of being able to make a long term monitoring with the same system. An antenna pattern monitoring system for the MU radar was developed using the scientific satellite OHZORA (EXOS-C). A receiver named MUM (MU radar antenna Monitor) on board the satellite measures a CW signal of 100 to 400 watts transmitted from the MU radar. The principle of the measurement and results are discussed.

Sato, T.↗
NASA NTRS1978

Charging of flexible solar array substrates in kilovolt electron beams

A series of survey tests were conducted to evaluate samples of flexible solar arrays. The samples used woven carbon fibers and/or coatings to increase the surface conductivity of the KAPTON substrate and thereby reduce surface charging. Four different samples were evaluated by exposing them to monoenergetic electron beams of 2 to 20 KeV at a current density of 1 nA sq cm. Simulated eclipse tests were also conducted. The results were as expected; the more continuous the conductive pattern, the lower the surface charging.

Staskus, J. V.↗
NASA NTRS1986

Shear strains in a graphite-PEEK beam by moire interferometry with carrier fringes

A multispan quasi-isotropic graphite-PEEK beam exhibited dramatic shear strains in the interlaminar region between plies. Shear strains in the plies themselves varied in basic accord with fiber direction. Large anomalous shear strains developed near the center of the beam height, where shear stresses were large. High-sensitivity moire interferometry with 2400 lines/mm was used. A new technique of data extraction was developed, using carrier fringes to transform the pattern to one in which fringe slopes are proportional to derivatives of displacement. It enhanced detection and measurement of highly localized shear-strain gradients.

Post, Daniel↗
NASA NTRS1992

Advanced Communication Technology Satellite (ACTS) multibeam antenna technology verification experiments

The Advanced Communication Technology Satellite (ACTS) is a key to reaching NASA's goal of developing high-risk, advanced communications technology using multiple frequency bands to support the nation's future communication needs. Using the multiple, dynamic hopping spot beams, and advanced on board switching and processing systems, ACTS will open a new era in communications satellite technology. One of the key technologies to be validated as part of the ACTS program is the multibeam antenna with rapidly reconfigurable hopping and fixed spot beam to serve users equipped with small-aperature terminals within the coverage areas. The proposed antenna technology experiments are designed to evaluate in-orbit ACTS multibeam antenna performance (radiation pattern, gain, cross pol levels, etc.).

Acosta, Roberto J.↗
NASA NTRS2009

System for Automated Calibration of Vector Modulators

Vector modulators are used to impose baseband modulation on RF signals, but non-ideal behavior limits the overall performance. The non-ideal behavior of the vector modulator is compensated using data collected with the use of an automated test system driven by a LabVIEW program that systematically applies thousands of control-signal values to the device under test and collects RF measurement data. The technology innovation automates several steps in the process. First, an automated test system, using computer controlled digital-to-analog converters (DACs) and a computer-controlled vector network analyzer (VNA) systematically can apply different I and Q signals (which represent the complex number by which the RF signal is multiplied) to the vector modulator under test (VMUT), while measuring the RF performance specifically, gain and phase. The automated test system uses the LabVIEW software to control the test equipment, collect the data, and write it to a file. The input to the Lab - VIEW program is either user-input for systematic variation, or is provided in a file containing specific test values that should be fed to the VMUT. The output file contains both the control signals and the measured data. The second step is to post-process the file to determine the correction functions as needed. The result of the entire process is a tabular representation, which allows translation of a desired I/Q value to the required analog control signals to produce a particular RF behavior. In some applications, corrected performance is needed only for a limited range. If the vector modulator is being used as a phase shifter, there is only a need to correct I and Q values that represent points on a circle, not the entire plane. This innovation has been used to calibrate 2-GHz MMIC (monolithic microwave integrated circuit) vector modulators in the High EIRP Cluster Array project (EIRP is high effective isotropic radiated power). These calibrations were then used to create correction tables to allow the commanding of the phase shift in each of four channels used as a phased array for beam steering of a Ka-band (32-GHz) signal. The system also was the basis of a breadboard electronic beam steering system. In this breadboard, the goal was not to make systematic measurements of the properties of a vector modulator, but to drive the breadboard with a series of test patterns varying in phase and amplitude. This is essentially the same calibration process, but with the difference that the data collection process is oriented toward collecting breadboard performance, rather than the measurement of output from a network analyzer.

Lux, James↗
NASA NTRS2005

[Development of X-ray Reflection Grating Technology for the Constellation-X Mission]

This Grant supports MIT technology development of x-ray reflection gratings for the Constellation-X Reflection Grating Spectrometer (RGS). Since the start of the Grant MIT has extended its previously-developed patterning and super-smooth, blazed grating fabrication technology to ten-times smaller grating periods and ten-times larger blaze angles to demonstrate feasibility and performance in the off-plane grating geometry. In the past year we have focused our efforts on extending our Nanoruler grating fabrication tool to enable it to perform variable-period scanning-beam interference lithography (VP-SBIL). This new capability required extensive optical and mechanical improvements to the system. The design phase of this work is largely completed and key components are now on order and assembly has begun. Over the next several months the new VP-SBIL Nanoruler system will be completed and testing begun. We have also demonstrated a new technique for patterning gratings using the Nanoruler called Doppler mode, which will be important for patterning the radial groove gratings for the RGS using the new VP-SBIL system. Flat and thin grating substrates will be critical for the RGS. In the last year we demonstrated a new technique for flattening thin substrates using magneto-rheologic fluid polishing (MRF) and achieved 2 arcsecond flatness with a 0.5 mm-thick substrate-a world's record. This meets the Con X requirement for grating substrate flatness.

Schattenburg, Mark L.↗
DOE OSTI2024

Dry etching of epitaxial InGaAs/InAlAs/InAlGaAs structures for fabrication of photonic integrated circuits

A dry etching process to transfer the pattern of a photonic integrated circuit design for high-speed laser communications is described. The laser stack under consideration is a 3.2-µm-thick InGaAs/InAlAs/InAlGaAs epitaxial structure grown by molecular beam epitaxy. The etching was performed using Cl2-based inductively-coupled-plasma and reactive-ion-etching (ICP-RIE) reactors. Four different recipes are presented in two similar ICP-RIE reactors, with special attention paid to the etched features formed with various hard mask compositions, in-situ passivations, and process temperatures. The results indicate that it is possible to produce high-aspect-ratio features with sub-micron separation on this multilayer structure. Additionally, the results of the etching highlight the tradeoffs involved with the corresponding recipes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Variable beamwidth monopulse feed for Tracking and Data Relay Satellite (TDRS)

The Tracking and Data Relay Satellite with a set of circularly-polarized, amplitude-sensing monopulse patterns suitable for acquiring and tracking user spacecraft at Ku-band (15.0 GHz) is discussed. The possibility of increasing the less than 0.4-degree half-power beamwidth of the data beam to almost 1.0 degree during the acquisition phase is predicated on the use of feeds situated in the first bright-ring of the Airy diffraction structure. A complex-vector simulation equivalent to the Kirchhoff-Kottler or Franz formulations is used to compute transmitted and received field information for a dual-reflector (Cassegrain) antenna configuration in a three-dimensional space.

Schmidt, R. F.↗
NASA NTRS1976

Scanning laser Doppler velocimeter system simulation for sensing aircraft wake vortices

A model that simulates the interaction of a laser-Doppler velocimeter with an aircraft wake flowfield is described. A hydrodynamic model is developed which represents the trailing vortex sheet and wind shear as discrete free vortices distributed over a two-dimensional grid. A sensor model is formulated for scanning both in range and in angle to produce a fan beam configuration without frequency translation. Output of this model is a frequency spectrum vs both range and angle. Once the spectrum is evaluated, simulations of the data analysis procedure are carried out. Patterns of various features of the signature are presented in range-elevation angle plots. The problem of locating the vortex centers is discussed as a pattern recognition problem and as a point target problem.

Thomson, J. A. L.↗
NASA NTRS1986

Laser-assisted solar cell metallization processing

The status of the laser-assisted solar cell metallization processing is described. Metallo-organic silver films were spun-on by argon ion laser beam pyrolysis. The metallo-organic decomposition (MOD) film was spun-on an evaporated Ti/Pd film to produce tood adhesion. In a maskless process, the argon ion laser writes the contact pattern. The film is then built up to obtain the required conductivity using conventional silverplating process. The Ti/Pd film in the field is chemically etched using the plated silver film as the mask. The width of the contact pattern is determined by the power of the laser. Widths as thin as 20 microns were obtained using 0.66 W of laser power. Cells fabricated with the 50 micron line widths of 4 ohm-cm floating zone (Fz) silicon-produced efficiencies of 16.6% (no passivation) which were equivalent to the best cells using conventional metallization/lithography and no passivation.

Meier, D. L.↗
NASA NTRS2005

Scaling device for photographic images

A scaling device projects a known optical pattern into the field of view of a camera, which can be employed as a reference scale in a resulting photograph of a remote object, for example. The device comprises an optical beam projector that projects two or more spaced, parallel optical beams onto a surface of a remotely located object to be photographed. The resulting beam spots or lines on the object are spaced from one another by a known, predetermined distance. As a result, the size of other objects or features in the photograph can be determined through comparison of their size to the known distance between the beam spots. Preferably, the device is a small, battery-powered device that can be attached to a camera and employs one or more laser light sources and associated optics to generate the parallel light beams. In a first embodiment of the invention, a single laser light source is employed, but multiple parallel beams are generated thereby through use of beam splitting optics. In another embodiment, multiple individual laser light sources are employed that are mounted in the device parallel to one another to generate the multiple parallel beams.

Rivera, Jorge E.↗
DOE OSTI2026

Interplay of Quantum Size Effect and Tensile Strain on Surface Morphology of β-Sn(100) Islands

The quantum size effect (QSE) and strain effect are two key factors influencing the surface morphology of thin films, which can increase film surface roughness through QSE-induced thickness oscillation and strain-induced island formation, respectively. Surface roughness usually manifests in the early stages of film growth and diminishes beyond a critical thickness. In this work, we employ molecular beam epitaxy (MBE) to grow β-Sn(100) islands with varying thickness N on bilayer graphene-terminated 6H-SiC(0001) substrates. Scanning tunneling microscopy and spectroscopy measurements reveal an inverse surface roughness effect that highlights the interplay of QSE and misfit strain in shaping the surface morphology of β-Sn(100) islands. For N ≤ 10, the islands exhibit flat surfaces, while for N ≥ 26, the island surfaces become corrugated and patterned. For the intermediate range, i.e., 12 ≤ N ≤ 24, both flat and patterned surfaces coexist, with the percentage coverage of the patterned surface oscillating as a function of N. By performing density functional theory calculations, we demonstrate that the unusual surface pattern evolution in our MBE-grown β-Sn(100) islands is a result of the interplay between QSE-induced surface roughing and tensile strain-induced smoothening effect.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

High-resolution chemical patterns from negative tone resists for the integration of extreme ultraviolet patterns of metal-oxide resists with directed self-assembly of block copolymers

Extreme ultraviolet (EUV) lithography faces significant challenges in designing suitable resist materials that can provide adequate precision, while maintaining economically viable throughput. These challenges in resist materials have led to printing failures and high roughness in EUV patterns, compromising the performance of semiconductor devices. Integrating directed self-assembly (DSA) of block copolymers (BCPs) with EUV lithography offers a promising solution because, while the BCPs register to the EUV-defined chemical guiding pattern, the thermodynamically determined structures of the BCPs automatically rectify defects and roughness in the EUV pattern. Despite the superior resolution of metal-oxide EUV resists (MORs), their application to DSA is limited by the difficulty in converting them into chemical patterns that allow effective transfer of the rectified patterns of DSA films into inorganic materials. To address this challenge, this study introduces a novel strategy for fabricating chemical patterns using hydrogen silsesquioxane (HSQ), a high-resolution negative tone inorganic resist, as a model system for MORs. Initially, a sacrificial Cr pattern is generated from HSQ patterns via reactive ion etching. The sacrificial Cr pattern is converted into a chemical pattern by first grafting a water-soluble polyethylene oxide brush onto the substrate, then wet etching the Cr, and finally grafting nonpolar polystyrene brushes. Assembling polystyrene-block-poly(methyl methacrylate) on these patterns results in structures oriented and registered with the underlying pattern, achieving 24 nm full-pitch resolutions. In conclusion, this approach has the potential to integrate MOR patterns into the DSA process, thereby enabling the generation of high-quality sub-10 nm patterns with high-χ BCPs.

Atomic force microscopy↗
DOE OSTI2024

Exploring Interferometry Diagnostics for Optical Stochastic Cooling at FAST/IOTA

Optical Stochastic Cooling (OSC) is an advanced beam-cooling technique that will precede the traditional stochastic cooling. This method leverages optical radiation and high-precision feedback to cool the particles more efficiently than traditional stochastic methods by more than three orders of magnitude. As such, it is an enabler for the development of next generation discovery science machines at the frontiers of energy and intensity. This paper focuses on the development of the second phase of OSC and improving extreme beam cooling technique in accelerators. Along with the assembly and use of an interferometer to provide diagnostics and optimization to OSC systems. The interferometer can allow for the observation and analysis of fringe patterns from a recreated simpler version in the laser room. By leveraging interferometric techniques, OSC can achieve higher efficiency, verification, stability and performance.

Teriba, Folashade↗
NASA NTRS1976

A new look at decomposition of turbulence forcing field and the structural response

Measured cross-spectrum of a turbulence field usually shows some decay in the statistical correlation in addition to convection at a characteristic velocity. It is shown that a decaying turbulence can be decomposed into frozen-pattern components thus permitting a simpler way to calculate the structural response. This procedure also provides a relationship whereby the measured input spectra can be incorporated. The theory is applied to an infinite beam which is backed on one side by a fluid filled cavity and is exposed on the other side by the turbulence excitation. The effect of the free stream velocity is also taken into consideration.

Lin, Y. K.↗
NASA NTRS1977

Response of periodic beam to supersonic boundary-layer pressure fluctuations

The response of a periodic beam (modeling a periodic fuselage) to supersonic boundary-layer pressure fluctuations is analyzed on the basis of a scheme in which a decaying turbulence is treated as a superposition of frozen-pattern components, thus allowing the structural response to be similarly superposed and the advantage of frozen-pattern analysis to be maximally utilized. The fundamental solution required for the construction of the total response is one corresponding to the excitation of a frozen-pattern sinusoid. To obtain this fundamental solution, the formulation follows Mead's wave-propagation method (1971), but also takes into account the effect of freestream velocity on the same side of the turbulence excitation and the effect of a cavity on the opposite side of the excitation. As a numerical example, the spectral density of the structural response is computed and the results are compared with experimental data.

Lin, Y. K.↗
NASA NTRS1984

Development of the phase/Doppler spray analyzer for liquid drop size and velocity characterizations

The present novel method for spray drop size and velocity measurement is analogous to a laser Doppler velocimeter, obtaining data from the spatial frequency of the interference fringe pattern produced by light scattering. Monodisperse droplet streams were used as a basic test of the theory, as well as of the susceptibility of the method to effects involved in actual application. Either beam intersection angle or detector spacing can be changed to achieve the same result. Polydispersed sprays were also measured.

Bachalo, W. D.↗
NASA NTRS1989

Feasibility study of a synthesis procedure for array feeds to improve radiation performance of large distorted reflector antennas

Surface errors on parabolic reflector antennas degrade the overall performance of the antenna. The errors are in the form of roughness on the surface, distortions in the shape, or structural design details. They cause amplitude and phase errors in the aperture field which lower the gain, raise the sidelobes, and fill in the nulls. These are major problems in large space reflector antennas. Planned mobile satellite communications systems having limited signal margin need high gain from the space reflectors. Future multiple beam antenna systems requiring spatial isolation to allow frequency reuse could be rendered useless if high sidelobes are present. High sidelobes are also responsible for noise. Ways of compensating for surface errors by pattern synthesis using an array of feed antennas are examined. Pattern corrections are directed specifically toward portions of the pattern requiring improvements. The pattern synthesis does not require knowledge of the surface errors. Both the amplitude and phase of the high side lobes caused by the distortion are required.

Stutzman, W. L.↗