Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

EGS Reservoir Modeling for Developing Geothermal District Heating at Cornell University

Cornell University is pursuing development of an enhanced geothermal system (EGS) for providing heating to its main campus in Upstate New York. A ~10,000 ft (~3 km) deep vertical observation well ('CUBO') was drilled in 2022 to characterize the subsurface using wellbore logging, borehole imaging, fluid sampling, mini-frac tests, coring and drill cutting analysis. Down-hole temperatures measured at 3 km depth are about 80 degrees C, sufficiently high for direct-use heating. The well drilled through generally low porosity and low permeability Paleozoic sedimentary formations and into metamorphic basement rock, encountered at about 9,400 ft depth. Leveraging subsurface data obtained through CUBO, we investigated technical feasibility and design requirements of a doublet well system with horizontal laterals connected to a fracture network created through hydraulic fracturing. The EGS reservoir is sized to provide a nominal heat output in the range 5 to 10 MWth of continuous heating over a 15 year-lifetime with limited thermal drawdown. We applied the Gringarten Multiple parallel fracture model, the Cornell Discrete Fracture Simulator FOXFEM and the commercial simulator ResFrac to estimate required heat transfer area and design a potential hydraulic stimulation treatment. Reservoir simulations indicate that, depending on fluid flow rate and injection temperature, 2 to 3 km2 of effective fracture heat transfer area is required to supply the target heat output of 5 to 10 MWth over 15 years.

district heating↗

Isobar channels and nucleon resonances in {pi}{sup +{pi}-} electroproduction on protons

Acomprehensive set of differential cross sections for the reaction {gamma}{sub {nu}p} {sup {yields} {pi}-{pi}+}p at the square of the photon 4-momentum in the range 0.2 < Q{sup 2} < 0.6 GeV{sup 2} and the invariant mass of final-state hadrons in the range 1.3 < W < 1.6 GeV was first obtained with the CLAS detector at the Thomas Jefferson Laboratory. An analysis of these data on the basis of the phenomenological model developed by physicists from the Institute of Nuclear Physics at Moscow State University (INP MSU) and Thomas Jefferson Laboratory (INP MSU-Hall B at Jefferson Lab Collaboration) made it possible to determine, for the first time, the contributions of all isobar channels to the differential cross sections in question. The possibility of extracting the Q{sup 2} dependences of the electromagnetic form factors for the P{sub 11}(1440) and D{sub 13}(1520) resonances in a kinematical region that is the most sensitive to the contribution of the meson-baryon cloud to the structure of nucleon resonances is demonstrated.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Epitaxial Crystal Silicon Absorber Layers and Solar Cells Grown at 1.8 Microns per Minute: Preprint

We have grown device-quality epitaxial silicon thin films at growth rates up to 1.8 ..mu..m/min, using hot-wire chemical vapor deposition from silane at substrate temperatures below 750 degrees C. At these rates, which are more than 30 times faster than those used by the amorphous and nanocrystalline Si industry, capital costs for large-scale solar cell production would be dramatically reduced,even for cell absorber layers up to 10 ?m thick. We achieved high growth rates by optimizing the three key parameters: silane flow, depletion, and filament geometry, based on our model developed earlier. Hydrogen coverage of the filament surface likely limits silane decomposition and growth rate at high system pressures. No considerable deterioration in PV device performance is observed whengrown at high rate, provided that the epitaxial growth is initiated at low rate. A simple mesa device structure (wafer/epi Si/a-Si(i)/a-Si:H(p)/ITO) with a 2.3 um epitaxial silicon absorber layer was grown at 700 nm/min. The finished device had an open-circuit voltage of 0.424 V without hydrogenation treatment.

14 SOLAR ENERGY↗

Morphology Development in Model Polyethylene via Two-Dimensional Correlation Analysis

Two-dimensional (2D) correlation analysis is applied to synchrotron X-ray scattering data to characterize morphological regimes during nonisothermal crystallization of a model ethylene copolymer (hydrogenated polybutadiene, HPBD). The 2D correlation patterns highlight relationships among multiple characteristics of structure evolution, particularly the extent to which separate features change simultaneously versus sequentially. By visualizing these relationships during cooling, evidence is obtained for two separate physical processes occurring in what is known as 'irreversible crystallization' in random ethylene copolymers. Initial growth of primarily lamellae into unconstrained melt ('primary-irreversible crystallization') is distinguished from subsequent secondary lamellae formation in the constrained, noncrystalline regions between the primary lamellae ('secondary-irreversible crystallization'). At successively lower temperatures ('reversible crystallization'), growth of the crystalline reflections is found to occur simultaneously with the change in shape of the amorphous halo, which is inconsistent with the formation of an additional phase. Rather, the synchronous character supports the view that growth of frustrated crystals distorts the adjacent noncrystalline material. Furthermore, heterocorrelation analysis of small-angle and wide-angle X-ray scattering data from the reversible crystallization regime reveals that the size of new crystals is consistent with fringed-micellar structures (9 nm). Thus, 2D correlation analysis provides new insights into morphology development in polymeric systems.

36 MATERIALS SCIENCE↗

Numerical simulation of spall in lead accounting for its occurrence in solid as well as liquid phases

The capabilities of a recently-developed continuum-level model developed for the purpose of predicting the evolution of spall, including the compaction of damaged material, and applicable to the formation of spall in the material that is fully solid as well as material that is locally liquid, are evaluated against empirical data for lead. Here, the model accounts for inertial forces, elastoplastic constitutive behavior, viscosity, and surface tension. Predictions of spall layer thickness are shown to match the empirical data reasonably well.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Magnetoresistance Hysteresis Evolution in the Granular Y–Ba–Cu–O High-Temperature Superconductor in a Wide Temperature Range

The temperature evolution of the magnetoresistance hysteresis in the granular YBa{sub 2}Cu{sub 3}O{sub 7-δ} high-temperature (T{sub C} ≈ 92 K) superconductor has been investigated. The measurements have been performed in the high-temperature region (78–90 K) and at the liquid helium temperature (4.2 K). The results obtained have been analyzed using the developed model of the behavior of transport properties of a granular high-temperature superconductor in an external magnetic field. Within the discussed model, the dissipation of the grain boundary subsystem is determined by the intergrain spacing-averaged effective field B{sub eff}, which is a superposition of external field H and the field induced by the magnetic moments of superconducting grains. Such a consideration yields the expression B{sub eff}(H) = H − 4πM(H) α for the effective field in the intergrain medium, where M(H) is the experimental hysteretic dependence of magnetization and α is the parameter of magnetic flux crowding in the intergrain medium. Here, the magnetoresistance is assumed to be proportional to the absolute value of the effective field: R(H) ~ |B{sub eff}(H)|. Analysis of the experimental R(H) and M(H) dependences obtained under the same conditions for the investigated high-temperature superconductor sample showed that in the high-temperature region this parameter is α ≈ 25. At the low temperature (4.2 K), we may state that the degree of flux crowding increases and the estimated α value is ~ 50. The estimates made are indicative of the strong effect of flux compression in the intergrain medium on the magnetotransport properties of the investigated granular high-temperature superconductor system. Possible reasons for a discrepancy between the developed model concepts and experimentally observed low-temperature R(H) hysteresis are analyzed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Feedforward Control of Fuel Distribution on Advanced Dual-Fuel Engines with Varying Intake Valve Closing Timings

This study examines the dynamics and control of an engine operated with late intake valve closure (LIVC) timings in a dual-fuel combustion mode. The engine features a fuel delivery system in which diesel is direct-injected and natural gas is port-injected. Despite the benefits of LIVC and dual-fuel strategy, combining these two techniques resulted in efficiency losses due to the variability of the combustion process across cylinders. The difference in power production across cylinders ranges from 9% at an IVC of 570°ATDC* to 38% at an IVC of 620 °ATDC and indicates an increasingly uneven fuel distribution as the intake valve remains open longer in the compression stroke. This paper describes an approach for controlling the amount of fuel injected into each cylinders’ port of an inline six- cylinder heavy-duty dual-fuel engine to minimize the variations in fuel distribution across cylinder. Since measuring the actual fuel reaching each cylinder is not a practical option on stock engines, this study aimed to produce a feedforward control technique. Using a model developed on an engine simulation software, the optimal fuel injection amounts at each cylinder port across 125 operating conditions (consisting of sweeps of five engine speeds, five engine loads, and five IVC timings) were determined by using PI controllers that adjust the amount of fuel injected at each port based on the amount of fuel reaching the cylinders. The results from the PI controller were expressed as a function of the operating condition (engine speed, engine load, and IVC timing); and consequently, could be reproduced without relying on a measurement of the amount of fuel reaching each cylinder. The feedforward control strategy, unlike the PI controller, is easily implementable on a stock engine and significantly reduces the variations in fuel distribution across cylinders.

Kassa, Mateos↗

Sodium-Cooled Fast Reactor Reference Plant Model

This report details the progress of Idaho National Laboratory (INL) in creating a reference plant multiphysics model for the Advanced Burner Test Reactor (ABTR). This model was developed under Task 13 of the U.S. Nuclear Regulatory Commission project “Development and Modeling Support for Advanced Non-Light Water Reactors,” and is an extension of the reference plant model developed in Task 4b, which was improved upon in the following ways. (1) The discrete ordinates method was used in lieu of the super-homogenization (SPH)-corrected diffusion approximation in order to better capture the anisotropic scattering contribution and the neutron leakage change due to thermal expansion. (2) The novel neutronic spatial discretization approach, termed the ring-heterogeneous (RH) approximation, was conceptualized and introduced to capture the differential expansion of the materials in the core. This new technique proved capable of preserving fission rates and maintaining the eigenvalue within 2.5% and 266 pcm with 9 neutron energy groups, respectively. Separating the different materials in the core enables the differential expansion of materials to be explicitly accounted for, eliminating the need for problem-specific cross-section functionalization techniques. (3) The SAM model for the core and system thermal-hydraulics analysis was updated to include 61 channels instead of just four representative ones. This enables users to obtain improved spatial resolution for sodium temperature and density scalar fields. (4) All the mesh files were created via the Multiphysics Object-Oriented Simulation Environment (MOOSE) Reactor module, eliminating all reliance on external tools for mesh creation. (5) Finally, the fuel axial expansion now leverages the HT9 and UPuZr material properties that have been validated against experimental data. The reference plant model was used to perform a full-core unprotected loss of flow (ULOF) transient calculation, including neutronics, thermal and mechanical feedback mechanisms. Future work will be devoted to further enhancements of the model. Potential improvements to the model include the addition of the control rod driveline expansion feedback and the upgrading of the support plate model so as to explicitly include 3D effects. Additionally, a Nuclear Energy Advanced Modeling and Simulation funded parallel effort has completely automated the creation of the ring-heterogeneous (RH) mesh from the fully heterogeneous (FH) geometry, thus maximizing user friendliness for the sodium fast reactor sodium-cooled fast reactor (SFR) workflow and will be incorporated in future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Ignition and flame characteristics of cryogenic hydrogen releases

In this work, under-expanded cryogenic hydrogen jets were investigated experimentally for their ignition and flame characteristics. The test facility described herein, was designed and constructed to release hydrogen at a constant temperature and pressure, to study the dispersion and thermo-physical properties of cryogenic hydrogen releases and flames. In this study, a non-intrusive laser spark focused on the jet axis was used to measure the maximum ignition distance. The radiative power emitted by the corresponding jet flames was also measured for a range of release scenarios from 37 K to 295 K, 2–6 bar abs through nozzles with diameters from 0.75 to 1.25 mm. The maximum ignition distance scales linearly with the effective jet diameter (which scales as the square root of the stagnant fluid density). A 1-dimensional (stream-wise) cryogenic hydrogen release model developed previously at Sandia National Laboratories (although this model is not yet validated for cryogenic hydrogen) was exercised to predict that the mean mole fraction at the maximum ignition distance is approximately 0.14, and is not dependent on the release conditions. The flame length and width were extracted from visible and infra-red flame images for several test cases. The flame length and width both scale as the square root of jet exit Reynolds number, as reported in the literature for flames from atmospheric temperature hydrogen. As shown in previous studies for ignited atmospheric temperature hydrogen, the radiative power from the jet flames of cold hydrogen scales as a logarithmic function of the global flame residence time. The radiative heat flux from jet flames of cold hydrogen is higher than the jet flames of atmospheric temperature hydrogen, for a given mass flow rate, due to the lower choked flow velocity of low-temperature hydrogen. Lastly, this study provides critical information with regard to the development of models to inform the safety codes and standards of hydrogen infrastructure.

08 HYDROGEN↗

Developing a model for the impact of non-conformal lithium contact on electro-chemo-mechanics and dendrite growth

Lithium dendrite growth hinders the use of lithium metal anodes in commercial batteries. We present a 3D model to study the mechanical and electrochemical mechanisms that drive microscale plating. With this model, we investigate electrochemical response across a lithium protrusion characteristic of rough anode surfaces, representing the separator as a porous polymer in non-conformal contact with a lithium anode. The impact of pressure on separator morphology and electrochemical response is of particular interest, as external pressure can improve cell performance. We explore the relationships between plating propensity, stack pressure, and material properties. External pressure suppresses lithium plating due to interfacial stress and separator pore closure, leading to inhomogeneous plating rates. For moderate pressures, dendrite growth is completely suppressed, as plating will occur in the electrolyte-filled gaps between anode and separator. In fast-charging conditions and systems with low electrolyte diffusivities, the benefits of pressure are overridden by ion transport limitations.

25 ENERGY STORAGE↗

Modeling Global Vegetation Gross Primary Productivity, Transpiration and Hyperspectral Canopy Radiative Transfer Simultaneously Using a Next Generation Land Surface Model—CliMA Land

Recent progress in satellite observations has provided unprecedented opportunities to monitor vegetation activity at global scale. However, a major challenge in fully utilizing remotely sensed data to constrain land surface models (LSMs) lies in inconsistencies between simulated and observed quantities. For example, gross primary productivity (GPP) and transpiration (T) that traditional LSMs simulate are not directly measurable from space, although they can be inferred from spaceborne observations using assumptions that are inconsistent with those LSMs. In comparison, canopy reflectance and fluorescence spectra that satellites can detect are not modeled by traditional LSMs. To bridge these quantities, we presented an overview of the next generation land model developed within the Climate Modeling Alliance (CliMA), and simulated global GPP, T, and hyperspectral canopy radiative transfer (RT; 400–2,500 nm for reflectance, 640–850 nm for fluorescence) at hourly time step and 1° spatial resolution using CliMA Land. CliMA Land predicts vegetation indices and outgoing radiances, including solar-induced chlorophyll fluorescence (SIF), normalized difference vegetation index (NDVI), enhanced vegetation index (EVI), and near infrared reflectance of vegetation (NIRv) for any given sun-sensor geometry. The spatial patterns of modeled GPP, T, SIF, NDVI, EVI, and NIRv correlate significantly with existing data-driven products (mean R 2 = 0.777 for 9 products). CliMA Land would be also useful in high temporal resolution simulations, for example, providing insights into when GPP, SIF, and NIRv diverge.

54 ENVIRONMENTAL SCIENCES↗