Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Strongly nonlinear wave propagation in elasto-plastic metamaterials: Low-order dynamic modeling

Nonlinear elastic metamaterials are known to support a variety of dynamic phenomena that enhance our capacity to manipulate elastic waves. Since these properties stem from complex, subwavelength geometry, full-scale dynamic simulations are often prohibitively expensive at scales of interest. Prior studies have therefore utilized low-order effective medium models, such as discrete mass-spring lattices, to capture essential properties in the long-wavelength limit. While models of this type have been successfully implemented for a wide variety of nonlinear elastic systems, they have predominantly considered dynamics depending only on the instantaneous kinematics of the lattice, neglecting history-dependent effects, such as wear and plasticity. Here, to address this limitation, the present study develops a lattice-based modeling framework for nonlinear elastic metamaterials undergoing plastic deformation. Due to the history- and rate-dependent nature of plasticity, the framework generally yields a system of differential-algebraic equations whose computational cost is significantly greater than an elastic system of comparable size. We demonstrate the method using several models inspired by classical lattice dynamics and continuum plasticity theory and explore means to obtain empirical plasticity models for general geometries, thereby gaining insight into the influence of microstructural plasticity on effective material performance, which can be used to improve the design of nonlinear mechanical metamaterials.

Dynamic simulation↗

Phase-field modeling of radiation-induced composition redistribution: An application to additively manufactured austenitic Fe–Cr–Ni

Multicomponent alloys undergoing irradiation damage develop radiation-induced composition redistribution at point defect sinks such as grain boundaries (GBs) and dislocations. Such redistribution results in undesired changes to their mechanical behavior and corrosion resistance. Additively manufactured alloys proposed for future nuclear applications are expected to demonstrate a distinct response to irradiation owing to their unique microstructure with as-solidified dislocation density and chemical microsegregation. To capture the composition redistribution in such systems, we develop a mesoscale model with coupled evolution of atomic and point defect components in the presence of dislocation density, dislocation heterogeneity, and thermodynamic interactions at the GB. The model is parameterized for an FCC Fe–Cr–Ni alloy as a representative system for austenitic stainless steels, and simulations are performed in 1D and 2D as a function of irradiation temperature, dose, dislocation density, and grain size. Radiation-induced segregation (RIS) characterized by Cr depletion and Ni enrichment is predicted at both the GB and the dislocation cell wall, with RIS being lower in magnitude but wider at the cell wall. Strongly biased absorption of self-interstitials by dislocations is found to suppress Ni enrichment but slightly enhance Cr depletion under certain conditions. Thermodynamic segregation at the GB is predicted to be narrower and opposite in sign to RIS for both Cr and Ni. Importantly, non-monotonic segregation is found to occur when both thermodynamic and RIS mechanisms are considered, providing a novel physical interpretation of experimental observations. The model is expected to serve as a key tool in accelerated qualification of irradiated materials.

additively manufactured microstructure↗

Design of a V–Ti–Ni alloy with superelastic nano-precipitates

Stress-induced martensitic transformations enable metastable alloys to exhibit enhanced strain hardening capacity, leading to improved formability and toughness. As is well-known from transformation-induced plasticity (TRIP) steels, however, the resulting martensite can limit ductility and fatigue life due to its intrinsic brittleness. In this work, we explore an alloy design strategy that utilizes stress-induced martensitic transformations but does not retain the martensite phase. This strategy is based on the introduction of superelastic nano-precipitates, which exhibit reverse transformation after initial stress-induced forward transformation. To this end, utilizing ab-initio simulations and thermodynamic calculations we designed and produced a V 45 Ti 30 Ni 25 (at%) alloy. In this alloy, TiNi is present as nano-precipitates uniformly distributed within a ductile V-rich base-centered cubic (bcc) β matrix, as well as being present as a larger matrix phase. We characterized the microstructure of the produced alloy using various scanning electron microscopy (SEM) and transmission electron microscopy (TEM) methods. Furthermore, the bulk mechanical properties of the alloy are demonstrated through tensile tests, and the reversible transformation in each of the TiNi morphologies were confirmed by in-situ TEM micro-pillar compression experiments, in-situ high-energy diffraction synchrotron cyclic tensile tests, indentation experiments, and differential scanning calorimetry experiments. The observed transformation pathways and variables impacting phase stability are critically discussed.

59 BASIC BIOLOGICAL SCIENCES↗

Plasticity and fracture behavior of Inconel 625 manufactured by laser powder bed fusion: Comparison between as-built and stress relieved conditions

In this work, the influence of stress relief on the plasticity and fracture behavior of Inconel 625 fabricated through laser powder bed fusion additive manufacturing (AM) was investigated. The as-built versus stress relieved microstructures were compared, showing similar grain structures but the presence of ~10 vol % δ phase in the stress relieved condition, and no δ phase in the as-built condition. Mechanical tests under plane strain tension were performed on the stress relieved samples, and an anisotropic plasticity model was calibrated and validated using finite element simulations. Uniaxial and notched tension tests were performed on both as-built and stress relieved samples to probe the effect of stress relief on stress state- and direction-dependent fracture behavior. It was found that on average, the fracture strain of the stress relieved samples along the build direction was 30% higher than that along the perpendicular build direction in the stress state range studied, and the stress relief heat treatment resulted in a 45% decrease in fracture strain. The fracture strain in stress relieved samples was more strongly dependent on stress state than in as-built samples.

36 MATERIALS SCIENCE↗

Regional Subsidence Analysis Through a Multi-Scale Modeling Framework Based on Breakage Mechanics

Although poroelastic models are often used to explain the delay between subsurface fluid depletion and ground subsidence, inelastic compaction involving permanent changes of rock microstructure may exacerbate hydro-mechanical coupling, thus influencing the interpretation of measurements and long-term forecasts. Here, a multi-scale modeling approach is discussed, which accounts for the inherent connection between rock microstructure, hydraulic conductivity, and pore compaction. A constitutive model built within the framework of breakage mechanics is proposed to link the hydraulic conductivity of granular rocks with inelastic deformations and changes in grading caused by injection-depletion cycles at stress levels far from yielding. The proposed model has been incorporated into large-scale simulation frameworks, thus enabling the spatiotemporal mapping of regional subsidence through a hybrid, semi-analytical approach. Numerical results based on this strategy show that the model allows isolating near-field and far-field effects into the computation of land subsidence and can generate forecasts for different modeling scenarios (e.g., elastic and inelastic compaction, constant permeability, and concurrent change of compressibility and permeability). In particular, examples of simulations for the case of the Groningen gas field are discussed, showing the model capabilities to use both field measurements and laboratory tests for the generation of reasonable subsidence maps, without expensive computational costs. Results indicate that ignoring coupled inelastic effects has major consequences on the predicted timescale of subsidence. Specifically, while all the model scenarios produced similar long-term ground settlements, those ignoring breakage-dependent permeability changes result in a variation of the temporal window of residual subsidence of the order of several decades.

58 GEOSCIENCES↗

Maximum strength and dislocation patterning in multi–principal element alloys

Multi–principal element alloys (MPEAs) containing three or more components in high concentrations render a tunable chemical short-range order (SRO). Leveraging large-scale atomistic simulations, we probe the limit of Hall-Petch strengthening and deformation mechanisms in a model CrCoNi alloy and unravel chemical ordering effects. The presence of SRO appreciably increases the maximum strength and lowers the propensity for faulting and structure transformation, accompanied by intensification of planar slip and strain localization. Deformation grains exhibit notably different microstructures and dislocation patterns that prominently depend on their crystallographic orientation and the number of active slip planes. Grain of single-planar slip attains the highest volume fraction of deformation-induced structure transformation, and grain with double-slip planes develops the densest dislocation network. These results advancing the fundamental understanding of deformation mechanisms and dislocation patterning in MPEAs suggest a mechanistic strategy for tuning mechanical behavior through simultaneously tailoring grain texture and local chemical order.

36 MATERIALS SCIENCE↗

Multi-frame, ultrafast, x-ray microscope for imaging shockwave dynamics

Inertial confinement fusion (ICF) holds increasing promise as a potential source of abundant, clean energy, but has been impeded by defects such as micro-voids in the ablator layer of the fuel capsules. It is critical to understand how these micro-voids interact with the laser-driven shock waves that compress the fuel pellet. At the Matter in Extreme Conditions (MEC) instrument at the Linac Coherent Light Source (LCLS), we utilized an x-ray pulse train with ns separation, an x-ray microscope, and an ultrafast x-ray imaging (UXI) detector to image shock wave interactions with micro-voids. To minimize the high- and low-frequency variations of the captured images, we incorporated principal component analysis (PCA) and image alignment for flat-field correction. After applying these techniques we generated phase and attenuation maps from a 2D hydrodynamic radiation code (xRAGE), which were used to simulate XPCI images that we qualitatively compare with experimental images, providing a one-to-one comparison for benchmarking material performance. Moreover, we implement a transport-of-intensity (TIE) based method to obtain the average projected mass density (areal density) of our experimental images, yielding insight into how defect-bearing ablator materials alter microstructural feature evolution, material compression, and shock wave propagation on ICF-relevant time scales.

47 OTHER INSTRUMENTATION↗

Austenite Formation and Manganese Partitioning during Double Soaking of an Ultralow Carbon Medium‐Manganese Steel

Double soaking (DS) is a thermal processing route intended to produce austenite–martensite microstructures in steels containing austenite‐stabilizing additions and consists of intercritical annealing (primary soaking), followed by heating and brief isothermal holding at an increased temperature (secondary soaking), and quenching. Herein, experimental dilatometry during DS of a medium‐manganese (Mn) steel with nominally 7 wt% Mn and an ultralow residual carbon concentration, in combination with phase‐field simulations of austenite formation during secondary soaking, is presented. The feasibility of maintaining heterogeneous Mn distributions during DS is demonstrated and insight is provided on the effects of the secondary soaking temperature and prior Mn distribution on the ferrite‐to‐austenite phase transformation during the secondary soaking portion of the DS treatment.

36 MATERIALS SCIENCE↗

Fatigue life prediction of powder bed fused–laser beam AlSi10Mg: Incorporating critical defects via crystal plasticity modelling

The current study provides a microstructurally-based computational framework to predict the fatigue life of additive manufactured (AM), i.e., powder bed fused–laser beam (PBF-LB), AlSi10Mg specimens using the crystal plasticity finite element method (CPFEM). The fractography analysis, electron backscatter diffraction (EBSD), uniaxial and cyclic responses, and fatigue life of specimens were used to inform the computational framework. CPFE simulation was used to compute fatigue indicator parameters (FIPs) as fatigue driving forces. A new fatigue criterion is introduced based on FIPs, which was calibrated using experimental fatigue data. The proposed fatigue measure was evaluated versus the specimens with critical defects of various sizes and locations subjected to different stress amplitudes. The results show that the developed framework can capture the fatigue life of samples with different critical defect locations and sizes along with different stress amplitudes for both high-cycle fatigue (HCF) and very high-cycle fatigue (VHCF) regimes.

Additive manufacturing↗

Correlation of coercivity, microstructure, and surface defects in HDDR-processed Nd-Fe-B powders for bonded magnet applications

Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) is an effective method for producing high coercivity, anisotropic powder from either fresh Nd-Fe-B alloy or recycled Nd-Fe-B magnets for use in bonded magnets. We investigated the impact of surface defects on the coercivity of HDDR-processed Nd-Fe-B using scanning electron microscopy (SEM), magnetic measurements, and micromagnetic simulations. We observed that coercivity decreases as particle size reduces, with SEM revealing surface defects and the detachment of Nd 2 Fe 14 B grains and Nd-rich phases from the particle surface. Micromagnetic simulations indicate that demagnetization initiates at the particle surface, where these defects are most concentrated, leading to reduced coercivity. The reduction in squareness of demagnetization curve, knee point field and coercivity for smaller HDDR particles is attributed to an increased specific surface area, which exhibits reduced nucleation field and weak domain wall pinning field during magnetization reversal. By addressing the role of surface defects in coercivity degradation, this study provides insights for improving both new powder production and recycling strategies, ultimately leading to enhanced performance of bonded magnets and contributing to more sustainable practices in the rare earth supply chain. One potential strategy to enhance the performance of HDDR Nd-Fe-B materials involves reducing the fraction of fine particles ($<$35 µm) and promoting the formation of grain boundary phases on particle surfaces.

Liu, Xubo B. [Ames Laboratory (AMES), Ames, IA (Un↗

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗

Particle interspacing effects on the mechanical behavior of a Fe–TiB 2 metal matrix composite using FFT-based mesoscopic field dislocation mechanics

This paper presents an application to metal matrix composites (MMCs) of an enhanced elasto-viscoplastic Fast Fourier Transform (EVP-FFT) formulation coupled with a phenomenological continuum Mesoscale Field Dislocation Mechanics (MFDM) theory. Contrary to conventional crystal plasticity, which only accounts for plastic flow and hardening induced by statistically stored dislocations (SSDs), MFDM-EVP-FFT also describes the evolution of polarized geometrically necessary dislocation (GND) density and its effect on both plastic flow and hardening. Numerical results for a Fe–TiB 2 MMC made of a ferrite matrix (α-Fe) and elastic ceramic particles (TiB 2 ) are presented. Full-field simulations are performed using synthetic periodic unit cells representative of the MMC, with single-crystalline and polycrystalline matrix, for different particle interspacing distances. A strong dependence of the predicted equivalent stress, cumulated plastic strain and GND density fields with particle interspacing distance is observed, in contrast with conventional crystal plasticity. Correlations between these mechanical fields and microstructural features, and their influence on local and global mechanical behavior are examined for the different MMC microstructures.

42 ENGINEERING↗

Stochastic parametric skeletal dosimetry model for humans: Pediatric and adult computational skeleton phantoms for internal bone marrow dosimetry

Currently, computational phantoms that simulate skeletal tissues are used in active red bone marrow (AM) internal dosimetry. Up-to-date reference computational phantoms recommended by the ICRP are based on the analysis of CT-images of cadavers. Such phantoms have significant disadvantages. One disadvantage is that the assessment of uncertainty due to the population variability of skeleton dimensions and microstructure results from the limited availability of autopsy material. Another disadvantage is the simplified modelling of cortical layer and bone microarchitecture. A method of stochastic parametric skeletal dosimetry modelling of the bone structures – SPSD modelling – has been developed as an alternative to the ICRP reference phantoms. In the framework of this approach, skeletal phantom parameters are evaluated based on extensively reviewed results of published measurements of real bones. The SPSD approach allows for the assessment of both population-average values and their variability. SPSD-phantoms of the skeleton are modelled in voxel representation. They consist of smaller phantoms of the bone sites – segments – described by simple geometric shapes with uniform microarchitecture parameters. Such segmentation makes it possible to account for non-homogeneous skeletal microarchitecture and to model the bone structure with the required voxel resolution to elaborate suitable skeletal phantoms. The current study presents the parameters of the SPSD skeletal phantoms for the following age-groups: newborn, 1-year-old, 5-year-old, 10-year-old, 15-year-old (male and female), and adult (male and female). This skeletal phantom can be used for dosimetry as an alternative to available reference phantoms for bone-seeking radionuclides. The above-mentioned age- and sex-specific skeletal phantoms are comprised of 289 unique segments. The characteristics of the SPSD phantoms do not contradict published data and are in good agreement with the measurement results of real bones.

Science & Technology - Other Topics↗

Research Needs for Uranium-Zirconium- Based Metallic Fuels

The purpose of this report is to summarize the needs and present recommendations related to the future direction for U-Zr-based metallic fuel research (including binary U-Zr and ternary U-Pu-Zr alloys). These needs and recommendations were determined by subject matter experts from various institutions during a two-day workshop held at the University of Florida in November, 2019. During open-floor discussions, the highest priority gaps in our understanding of U-Zr-based fuels were down-selected, and near- and long-term needs that directly impact the implementation of these metallic fuels were identified. The identified near-term needs include investigation of the following phenomena: i) swelling and fission gas release, ii) fuel-cladding chemical interaction, iii) phase evolution/constituent redistribution, and iv) thermal properties of the fuels. The long-term needs are: i) investigation of fuel creep and plasticity and ii) fission product (lanthanide) transport. In addition, there was general agreement that all institutions and subject matter experts would benefit from an open-source metallic fuels database with thermophysical property and microstructural data, along with fuel operation/irradiation history, which should be regularly updated with vetted information from new experimental and computational investigations and used to advance metallic fuels research and development. Finally, we recommend that metallic fuel research should be ongoing and that fuel qualification and fuel optimization should be equally prioritized; research combining experiments with modeling and simulation has the largest potential impact.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural refinement in ultrasonically modified A356 aluminum castings

Two A356 aluminum alloys (Al-Si-Mg), one with 0.09 wt.% Fe and one with 0.91 wt.% Fe, were cast in a graphite mold with the simultaneous application of local ultrasonic intensification to refine the as-cast microstructure. Ultrasonication during casting transformed the morphology of primary Al grains from dendritic (~140-290 microns in size) to globular (~33-36 microns in size). The alloy with high Fe exhibited globular grains at distances up to 45 mm away from the ultrasound probe, while the alloy with low Fe exhibited globular grains at distances only up to 6 mm away from the ultrasound probe. Near the location of the ultrasound probe (< 2 mm away), a second non-dendritic microstructural morphology was observed with fine aluminum grains (~9-25 microns in size). This unique fine-grained morphology has not been previously reported, contains a greater concentration of Si relative to the globular microstructure, and may be a large, fully eutectic region. Ultrasonication during casting also transformed the morphology of the ß-Al 5 FeSi phase particles (which are deleterious to the strength and ductility of the alloy) in the high Fe alloy from needle-like to rectangular, which could enable the greater use of secondary Al alloys. Thermodynamic simulations conducted to calculate the solidification paths of the two alloys studied predict that the ß-Al 5 FeSi phase begins to form earlier in the alloy with high Fe. Finally, data suggest that the ß-Al 5 FeSi phase (which is more abundant in alloys with high Fe content) may enhance ultrasonically-induced grain refinement.

36 MATERIALS SCIENCE↗

Multi-modal characterization of the B2 phase in the Ta-Re binary system

The energy and transportation industries demand materials that retain their mechanical property at high temperatures. Refractory complex concentrated alloys (RCCAs) with a BCC + B2 microstructure offer a potential solution, where maintaining the high temperature mechanical properties can be achieved by precipitation strengthening. This depends on the B2 phase in RCCAs being thermodynamically stable with a high solvus temperature. Recently, we predicted the high temperature stability of the B2 structure in the Ta-Re binary system, using density functional theory. Here, in this study, we provide experimental evidence for the existence of this phase for the first time, using a Ta 65 Re 35 alloy. Despite Ta-Re binary phase diagrams predicting a single-phase BCC microstructure for Ta 65 Re 35 , we show that a high Z nanoscale secondary phase appears after heat treatment at 1550 °C and 1100 °C. Scanning transmission electron microscopy (STEM) revealed that this phase has a cubic structure and is equiatomic TaRe though B2 superlattice reflections were absent in fast Fourier transforms (FFT) and diffraction patterns (DPs). DP simulations indicate that the B2 TaRe superlattice reflections are up to two orders of magnitude weaker than their fundamental reflections, making their detection challenging via electron microscopy. Neutron diffraction confirmed the second phase had a B2 structure. This study identified a previously unobserved high temperature stable B2 phase in the Ta-Re system, enabling the development of new high temperature BCC + B2 RCCAs.

36 MATERIALS SCIENCE↗

Mesh Computing Remote Automatic Workflow

The software suite uses a microservice architecture using Docker and `docker-compose`. The microservices are as follows: 1. User interface. This interface is written in JavaScript using the Svelte framework. It exposes form elements and a 3D visualizer to prompt the user through the definition of microstructure parameters, and setting parameters for mesh generation and refinement. 2. Mesh generator. This is a container running the Python package for DREAM3D to generate a voxelized mesh that represents a microstructure defined by the user in the interface. 3. Cubit runner. This is a secure shell protocol tool that makes the submitting the DREAM mesh to an HPC instance and starts to run Cubit shell commands to smooth the grain boundaries with its `sculpt` library, applies user-defined boundary node sets, and bundles and returns the simulation-ready meshes and input files as a zipped directory.

Harris, BrennanKay↗

Controlling reversible phase transitions in rare-earth nickelates for novel memory devices

Resistive switching in correlated complex oxides is lucrative for emerging applications in neuromorphic computing, and densely scaled non-volatile memory. Electrical conductance of such complex oxides can be controllable switched across multiple orders of magnitude by either (a) electroforming a conduction channel (e.g., in tungsten oxide), or (b) inducing Mott-Hubbard transition (e.g., in rare-earth nickelates)– both via controlled migration of defects (such as oxygen vacancies) under applied bias. Nevertheless, the promise of such defect-driven electronic transitions are far from realized due to a lack of fundamental understanding of the atomic-scale processes that underlie migration and spatiotemporal evolution of oxygen vacancies over nano-to-mesoscopic length/timescales under applied electric field. In this project, we employ a synergistic integration of density functional theory (DFT) calculations, ab initio/classical molecular dynamics (AIMD/CMD) simulations, machine learning (ML), precision synthesis, and multi-modal X-ray imaging experiments to address this knowledge gap. Such an integrated approach offers to elucidate the correlations between subtle structural distortion and oxidation states; treat localized charge carriers; describe defect/ion transport in the presence of electric field; and, in turn, greatly advance the current understanding of microstructural evolution in complex oxides under applied bias. The fundamental knowledge gained from this work will enable precise control over hierarchical defect structures and unravel new routes to manipulate resistance states in complex oxides. This, in turn, will accelerate design of novel devices with desired set of neural functionalities, and high-speed densely-scaled resistive random access memory technologies.

36 MATERIALS SCIENCE↗