SEARCH · Engineering Papers

Results for “laser processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

All sources NASA NTRS DOE OSTI

DOE OSTI2026

High-temperature mechanical properties of a γ′-strengthened Co-based superalloy designed for additive manufacturing

GammaPrint®-700 is a recently developed high γ′ (∼70% volume fraction) CoNi-based superalloy designed to combine high-temperature mechanical performance with laser powder bed fusion processability. Room-temperature yield strength ranged from 610 to 658 MPa and increased to 661 MPa (longitudinal) and 730 MPa (transverse) at 760 °C. The creep behavior compared favorably to high-γ′ Ni-based superalloys manufactured via laser powder bed fusion such as Incoloy® 939 and Inconel® 738LC. In-situ neutron diffraction data measured during creep revealed that plastic deformation was largely localized to the γ phase at 760 °C, allowing the γ’ phase to elastically compensate and maintain creep strain resistance. Furthermore, at 900 °C, this load sharing behavior was weakened, contributing to accelerated creep rate and rupture.

Creep↗

NASA NTRS1977

Laser-zone growth in a Ribbon-To-Ribbon (RTR) process. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

The Ribbon-to-Ribbon (RTR) approach to silicon ribbon growth is investigated. An existing RTR apparatus is to be upgraded to its full capabilities and operated routinely to investigate and optimize the effects of various growth parameters on growth results. A new RTR apparatus was constructed to incorporate increased capabilities and improvements over the first apparatus and to be capable of continuous growth. New high power lasers were implemented and this led to major improvements in growth velocity -- 4 inch/min. growth has been demonstrated. A major step in demonstration of the full feasibility of the RTR process is reported in the demonstration of RTR growth from CVD polyribbon rather than sliced polyribbon ingots. Average solar cell efficiencies of greater than 9% and a best cell efficiency of 11.7% are reported. Processing was shown to provide a substantial improvement in material minority carrier diffusion length. An economic analysis is reported which treats both the polyribbon fabrication and RTR processes.

Gurtler, R. W.↗

DOE OSTI2021

High-speed synchrotron X-ray imaging of directed energy deposition of titanium: effects of processing parameters on the formation of entrapped-gas pores

Laser based directed energy deposition (DED) is a competitive method for repairing and remanufacturing metallic parts used in numerous industries including aerospace and biomedical. However, the numerous dynamic phenomena associated with the DED process often result in defects such as entrapped-gas pores, lack of fusion, and undesirable anisotropic properties. The entrapped-gas pore, being one of the most common issues, not only influences melt-pool dynamics but also reduces the fabrication quality and mechanical properties of parts fabricated by the DED process. To reduce and further understand this issue, the real-time observation of the pore formation process needs to be studied first. To directly observe the phenomena in the melt pool, high-speed techniques are needed because rapid solidification leads to rapid pore formation and movement. In-situ high-speed X-ray has been proven to be an effective method in investigating the melt pool dynamics and pore formation mechanisms in the laser powder bed fusion process, in which the fabrication process is quite different from that in DED. Here, the high-speed X-ray method is extended to study the formation of entrapped-gas pores. The real-time formation and quantitative analysis of pores under each set of processing parameters (particle velocity, laser power, and spot welding dwelling time of stationary laser) in the DED process are investigated. We found that the DED with a higher particle velocity (3.19 m/s) produced a smaller average pore size of 27.8 µm and a lower pore area fraction of 0.52%. The DED under lower laser power (156 W) generated a smaller average pore size of 20.3 µm and a lower pore area fraction of 1.94%. The shorter dwelling time (10 ms) benefited the decrease of both average pore size and pore area fraction.

Defect↗

DOE OSTI2020

Progress Report on the Assessment of the Material Performance for TCR Applications

The objective of Argonne’s materials research activities for the Transformational Challenge Reactor (TCR) program is to improve the understanding of material properties from additive manufacturing with the focus on understanding the creep and fatigue properties of additively manufactured materials. The material work conducted by Argonne provides support in developing and qualifying advanced materials and manufacturing processes to allow for innovative reactor design and licensing for the TCR. In this report, we present the creep data at temperatures of 550, 600 and 650°C and stresses between 175 and 300 MPa for 316L stainless steel produced by a laser powder bed fusion process. We conducted five different post-build heat treatments, namely 650°C/1h, 750°C/1h, 800°C/1h, 900°C/1h and 1050°C/1h. Creep tests of the heat-treated specimens were performed under the same test condition, 550°C/275 MPa to evaluate and understand the effect of post-build heat treatment on the creep behavior of additively-manufactured 316L SS. Creep tests were conducted to ASME NQA-1 or its lab equivalent for quality assurance.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1977

Laser-zone growth in a Ribbon-To-Ribbon, RTR, process silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

A ribbon-to-ribbon process was used for routine growth of samples for analysis and fabrication into solar cells. One lot of solar cells was completely evaluated: ribbon solar cell efficiencies averaged 9.23% with a highest efficiency of 11.7%. Spherical reflectors have demonstrated significant improvements in laser silicon coupling efficiencies. Material analyses were performed including silicon photovoltage and open circuit photovoltage diffusion length measurements, crystal morphology studies, modulus of rupture measurements, and annealing/gettering studies. An initial economic analysis was performed indicating that ribbon-to-ribbon add-on costs of $.10/watt might be expected in the early 1980's.

Gurtler, R. W.↗

NASA NTRS2024

Short-Term Elevated Temperature Mechanical Performance and Microstructure of A Niobium-Zirconium Alloy Produced via Laser Powder Bed Fusion In-Situ Alloying

Nb-1Zr is a readily fabricable, dispersion-strengthened niobium alloy with improved elevated temperature properties compared to commercially pure niobium. This low to moderate strength niobium alloy is desirable in thermal management systems for fission power and propulsion applications; however, pre-alloyed spherical feedstock for powder-based additive manufacturing processes is generally unavailable. Laser powder bed fusion (L-PBF) in-situ alloying of a Nb-1Zr chemistry was performed using a high-purity niobium feedstock coated with 1 wt% of zirconium-based ceramic compound nano-powders: ZrO 2 , ZrC, and ZrH 2 . The additively manufactured material was mechanically tested at elevated temperatures within a controlled environment in the as-built condition. For comparison, traditionally manufactured wrought feedstock was also tested within an identical environment. Examination of the materials’ microstructure and short-term elevated temperature mechanical response determined: in-situ alloying of spherical Nb powder feedstock with Zr-based ceramic nanoparticles can be successfully implemented; the ZrO 2 addition offered the greatest elevated temperature stability and strength but exhibited brittle behavior; the ZrC addition achieved a balance of room temperature ductility and elevated temperature strength; and the ZrH 2 -modified material had the lowest as-built interstitial content and showed high ductility with mechanical performance most similar to wrought Nb-1Zr.

Niobium Alloy↗

DOE OSTI2020

Process optimization of complex geometries using feed forward control for laser powder bed fusion additive manufacturing

Additive manufacturing (AM) enables the fabrication of complex designs that are difficult to create by other means. Metal parts manufactured by laser powder bed fusion (LPBF) can incorporate intricate design features and demonstrate desirable mechanical properties. However, printing a part that is qualified for its intended application often involves reprinting and discarding many parts to eliminate defects, improve dimensional accuracy, and increase repeatability. The process of iteratively converging on the appropriate build parameters increases the time and cost of creating functional LPBF manufactured parts. This work describes a fast, scalable method for part-scale process optimization of arbitrary geometries. Additionally, the computational approach uses feature extraction to identify scan vectors in need of parameter adaptation and applies results from simulation-based feed forward control models. This method provides a framework to quickly optimize complex parts through the targeted application of models with a range of fidelity and by automating the transfer of optimization strategies to new part designs. The computational approach and algorithmic framework are described, a software package is implemented, the method is applied to parts with complex features, and parts are printed on a customized open architecture LPBF machine.

3D printing↗

DOE OSTI2023

Laser-Induced Fluorescence for Monitoring Environmental Contamination and Stress in the Moss Thuidium plicatile

The ability to detect, measure, and locate the source of contaminants, especially heavy metals and radionuclides, is of ongoing interest. A common tool for contaminant identification and bioremediation is vegetation that can accumulate and indicate recent and historic pollution. However, large-scale sampling can be costly and labor-intensive. Hence, non-invasive in-situ techniques such as laser-induced fluorescence (LIF) are becoming useful and effective ways to observe the health of plants through the excitation of organic molecules, e.g., chlorophyll. The technique presented utilizes images collected of LIF in moss to identify different metals and environmental stressors. Analysis through image processing of LIF response was key to identifying Cu, Zn, Pb, and a mixture of the metals at nmol/cm 2 levels. Specifically, the RGB values from each image were used to create density histograms of each color channel’s relative pixel abundance at each decimal code value. These histograms were then used to compare color shifts linked to the successful identification of contaminated moss samples. Photoperiod and extraneous environmental stressors had minimal impact on the histogram color shift compared to metals and presented with a response that differentiated them from metal contamination.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Remarkable enhancement in thermal conductivity of stainless-steel leveraging metal composite via laser powder bed fusion: 316L-Cu composite

This work aimed to significantly enhance the thermal conductivity of the SS matrix by fabricating a metal composite SS-Cu system utilizing a laser powder bed fusion process. The impact of process parameters on the microstructure of SS-Cu samples is investigated. Here, the processing and post-processing factors that influence the effective thermal conductivity of the metal composite SS-Cu system are discussed. Then, the effective thermal conductivity and mechanical properties of the SS-Cu composite are measured at room temperature and operating temperature of 300 °C. The optimized laser powder bed fusion parameters led to low Marangoni convection, high cooling rate, greater macro-segregation, and higher thermal conductivity values albeit at the cost of ductility in SS-Cu metal composite likely due to the presence of the unmelted powder particles. As-printed SS-60 vol % Cu and annealed SS-60 vol % Cu had 2.5X and 6.6X thermal conductivity enhancement, respectively. During annealing, phase separation, partial melting of Cu, and formation of a continuous network of Cu surrounding SS play a key role in enhancing the thermal conductivity of the SS-Cu metal composite structure.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Modeling Pore Closure in the Hot Isostatic Pressing of Additively Manufactured Inconel 718 Samples

Additive manufacturing provides opportunity for a new world of possibilities for metallic component design and fabrication; however, as-built part quality is notoriously variable, anisotropic, and degraded by porous defects. To improve quality, parts are commonly post processed using a variety of techniques including hot isostatic pressing (HIP). During HIP, high temperature and pressure is employed to improve microstructure and reduce pore volume by inducing visco-plastic deformation in the metallic substrate. Validated computational capabilities can provide predictions to guide the selection of processing condition, expected pore reduction, and the effects of varying entrapped gas in the pores. This discussion describes a micro-scale finite element structural model developed to predict pore closure due to HIP in as-built additively manufactured Inconel 718 samples produced by the laser powder bed fusion process. The model accounts for plastic deformation, creep, and internal pressure for a single pore. Pores are characterized in physical samples before and after HIP, and model predictions are compared to this measured data.

defect model prediction↗

DOE OSTI2022

Microstructurally-Inspired Strategies to Print Tantalum and Tantalum-Tungsten Alloys

The goal of this project is to investigate strategies to print tantalum and tantalumtungsten alloys, which are notoriously difficult to print with consistent results because of the sensitivity of the properties to small concentrations of interstitial impurities (particularly oxygen) and microstructure, and hence to processing conditions. In direct metal laser sintering (DMLS) Ta, a strong dependence of porosity, grain morphology and texture on processing conditions was found.

36 MATERIALS SCIENCE↗

NASA NTRS1991

Video Recording Of Images In Laser Remote Sensing

Timing technique enables recording of images in laser remote sensing of environment. Timings of laser pulse, shutter, and video frame synchronized. Technique also used in industrial or commercial processes requiring clear sighting of laser beams relative to their surroundings.

Kalshoven, James E., Jr.↗

DOE OSTI2024

Numerical investigation of nonequilibrium electron effects on the collisional ionization rate in the collisional-radiative model

In this study, the interplay of kinetic electron physics and atomic processes in ultrashort laser-plasma interactions provides a comprehensive understanding of the impact of the electron energy distribution on plasma properties. Notably, nonequilibrium electrons play a vital role in collisional ionization, influencing ionization degrees and spectra. This paper introduces a computational model that integrates the physics of kinetic electrons and atomic processes, utilizing a Boltzmann equation for nonequilibrium electrons and a collisional-radiative model for atomic state populations. The model is used to investigate the influence of nonequilibrium electrons on collisional ionization rates and its effect on the population distribution, as observed in a widely known experiment. The study reveals a significant nonequilibrium electron presence during XFEL-matter interactions, profoundly affecting collisional ionization rates in the gas plasma, thereby necessitating careful consideration of the Collisional-Radiative model applied to such systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1992

Two-Dimensional Laser-Speckle Surface-Strain Gauge

Extension of Yamaguchi's laser-speckle surface-strain-gauge method yields data on two-dimensional surface strains in times as short as fractions of second. Laser beams probe rough spot on surface of specimen before and after processing. Changes in speckle pattern of laser light reflected from spot indicative of changes in surface strains during processing. Used to monitor strains and changes in strains induced by hot-forming and subsequent cooling of steel.

Barranger, John P.↗

NASA NTRS1998

Cloud and Radiation Mission with Active and Passive Sensing from the Space Station

A cloud and aerosol radiative forcing and physical process study involving active laser and radar profiling with a combination of passive radiometric sounders and imagers would use the space station as an observation platform. The objectives are to observe the full three dimensional cloud and aerosol structure and the associated physical parameters leading to a complete measurement of radiation forcing processes. The instruments would include specialized radar and lidar for cloud and aerosol profiling, visible, infrared and microwave imaging radiometers with comprehensive channels for cloud and aerosol observation and specialized sounders. The low altitude,. available power and servicing capability of the space station are significant advantages for the active sensors and multiple passive instruments.

Spinhirne, James D.↗

DOE OSTI2022

Sensor fusion of pyrometry and acoustic measurements for localized keyhole pore identification in laser powder bed fusion

We report in-situ process monitoring as an aid to part qualification for laser powder-bed fusion (L-PBF) technology is a topic of increasing interest to the additive manufacturing community. In this work, airborne acoustic and inline pyrometry measurements were recorded simultaneously with the laser position. X-ray radiography imaging was used to spatio-temporally register keyhole pore locations to the pyrometry and acoustic signals, enabling binary labeling of data partitions based on pore formation. These labeled partitions were subsequently featurized using a highly comparative time-series analysis toolbox. Acoustic data was found to be much more effective than the pyrometry data for keyhole pore identification. However, when the information contained in both sensing modalities was combined in a sensor fusion strategy, the error rates of the top performing models were significantly reduced.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Photothermally Activated Artificial Neuromorphic Synapses

Biological nervous systems rely on the coordination of billions of neurons with complex, dynamic connectivity to enable the ability to process information and form memories. In turn, artificial intelligence and neuromorphic computing platforms have sought to mimic biological cognition through software-based neural networks and hardware demonstrations utilizing memristive circuitry with fixed dynamics. Here, to incorporate the advantages of tunable dynamic software implementations of neural networks into hardware, we develop a proof-of-concept artificial synapse with adaptable resistivity. This synapse leverages the photothermally induced local phase transition of VO 2 thin films by temporally modulated laser pulses. Such a process quickly modifies the conductivity of the film site-selectively by a factor of 500 to “activate” these neurons and store “memory” by applying varying bias voltages to induce self-sustained Joule heating between electrodes after activation with a laser. These synapses are demonstrated to undergo a complete heating and cooling cycle in less than 120 ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1993

Compound curvature laser window development

The NASA Lewis Research Center has developed and implemented a unique process for forming flawless compound curvature laser windows. These windows represent a major part of specialized, nonintrusive laser data acquisition systems used in a variety of compressor and turbine research test facilities. This report summarizes the main aspects of compound curvature laser window development. It is an overview of the methodology and the peculiarities associated with the formulation of these windows. Included in this discussion is new information regarding procedures for compound curvature laser window development.

Verhoff, Vincent G.↗