Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Mars Helicopter Ingenuity Rotor Geometry

The NASA Mars Helicopter Ingenuity performed its maiden flight on April 19, 2021, and opened new possibilities for planetary exploration. Ingenuity has ended its mission after experiencing an anomaly during its 72nd flight on January 18, 2024. Due to the low density and low temperature of the surface atmosphere on Mars, significant challenges must be overcome to achieve aerodynamic performance. The low density of the Martian atmosphere and the relatively small-scale rotor result in flows with very low Reynolds number, reducing the lifting force and lifting efficiency, respectively. Until recently, compressible flow at Reynolds numbers around Re = 10,000 was of moderate practical interest but with the success of Ingenuity, the aerodynamic regime is appreciating considerable attention. The purpose of this report is to document the geometry (planform, twist, and airfoils) of the Mars Helicopter rotor, for use in future research on rotor performance in the Mars atmosphere.

Mars↗

OpenACC offloading of the MFC compressible multiphase flow solver on AMD and NVIDIA GPUs

GPUs are the heart of the latest generations of supercomputers. We efficiently accelerate a compressible multiphase flow solver via OpenACC on NVIDIA and AMD Instinct GPUs. Optimization is accomplished by specifying the directive clauses gang vector and collapse. Further speedups of six and ten times are achieved by packing user-defined types into coalesced multidimensional arrays and manual inlining via metaprogramming. Additional optimizations yield seven-times speedup of array packing and thirty-times speedup of select kernels on Frontier. Weak scaling efficiencies of 97% and 95% are observed when scaling to 50% of Summit and 87% of Frontier. Strong scaling efficiencies of 84% and 81% are observed when increasing the device count by a factor of 8 and 16 on V100 and MI250X hardware. The strong scaling efficiency of AMD’s MI250X increases to 92% when increasing the device count by a factor of 16 when GPU-aware MPI is used for communication.

Wilfong, Benjamin↗

bhlight: GENERAL RELATIVISTIC RADIATION MAGNETOHYDRODYNAMICS WITH MONTE CARLO TRANSPORT

We present bhlight, a numerical scheme for solving the equations of general relativistic radiation magnetohydrodynamics using a direct Monte Carlo solution of the frequency-dependent radiative transport equation. bhlight is designed to evolve black hole accretion flows at intermediate accretion rate, in the regime between the classical radiatively efficient disk and the radiatively inefficient accretion flow (RIAF), in which global radiative effects play a sub-dominant but non-negligible role in disk dynamics. We describe the governing equations, numerical method, idiosyncrasies of our implementation, and a suite of test and convergence results. We also describe example applications to radiative Bondi accretion and to a slowly accreting Kerr black hole in axisymmetry.

79 ASTRONOMY AND ASTROPHYSICS↗

Euler and Navier-Stokes computations for two-dimensional geometries using unstructured meshes

A general purpose unstructured mesh solver for steady-state two-dimensional inviscid and viscous flows is described. The efficiency and accuracy of the method are enhanced by the simultaneous use of adaptive meshing and an unstructured multigrid technique. A method for generating highly stretched triangulations in regions of viscous flow is outlined, and a procedure for implementing an algebraic turbulence model on unstructured meshes is described. Results are shown for external and internal inviscid flows and for turbulent viscous flow over a multi-element airfoil configuration.

Mavriplis, D. J.↗

Euler and Navier-Stokes computations for airfoil geometries using unstructured meshes

A general purpose unstructured mesh solver for steady-state two-dimensional inviscid and viscous flows is described. The efficiency and accuracy of the method are enhanced by the simultaneous use of adaptive meshing and an unstructured multigrid technique. A method for generating highly stretched triangulations in regions of viscous flow is outlined, and a procedure for implementing an algebraic turbulence model on unstructured meshes is described. Results are shown for external and internal inviscid flows and for turbulent viscous flow over a multi-element airfoil configuration.

Mavriplis, D. J.↗

Advanced Electric Submersible Pump Design Tool for Geothermal Applications

Electrical Submersible Pumps (ESPs) present higher efficiency, larger production rate, and can be operated in deeper wells than the other geothermal artificial lifting systems. Enhanced Geothermal Systems (EGS) applications recommend lifting 300 C geothermal water at 80kg/s flow rate in a maximum 10-5/8-inch diameter wellbore to improve the cost-effectiveness. In this paper, an advanced ESP design tool comprising a 1D theoretical model and a 3D CFD analysis has been developed to design ESPs for geothermal applications. Design of Experiments was also performed to optimize the geometry and performance. The designed mixed-flow type centrifugal impeller and diffuser exhibit high efficiency and head rise under simulated EGS conditions. The design tool has been validated by comparing the prediction to experimental data of an existing ESP product.

15 GEOTHERMAL ENERGY↗

Overall and blade-element performance of a multiple-circular-arc bladed transonic compressor rotor with tip speed of 1375 feet per second

The design and experimental performance of a 20-inch-diameter multiple-circular-arc bladed axial-flow transonic compressor rotor is presented. Radial surveys of the flow conditions were made. At design speed the peak efficiency was 0.882 and occurred at a weight flow of 64.0 pounds per second. At this point the total-pressure and total-temperature ratios were 1.79 and 1.205, respectively. The stall margin at design speed was 8 percent based on weight flows and total-pressure ratios at experimental peak efficiency and near stall. The measured stall margin was 20 percent at design weight flow and speed.

Kovich, G.↗

Performance of a 1380-foot-per-second-tip-speed axial-flow compressor rotor with a blade tip solidity of 1.3

Aerodynamic design parameters are presented along the overall and blade element performance, of an axial flow compressor rotor designed to study the effects of blade solidity on efficiency and stall margin. At design speed the peak efficiency was 0.844 and occurred at an equivalent weight flow of 63.5 lb/sec with a total pressure ratio of 1.801. Design efficiency, pressure ratio, and weight flow 0.814, 1.65, and 65.3(41.1 lb/sec/sq ft of annulus area), respectively. Stall margin for design speed was 6.4 percent based on the weight flow and pressure ratio values at peak efficiency and just prior to stall.

Hager, R. D.↗

High-order dimensionally-split Cartesian embedded boundary method for non-dissipative schemes

Centered finite-difference schemes are commonly used for high-fidelity turbulent flow simulations in canonical configurations because of their non-dissipative property and computational efficiency. However, their use in flow simulations over complex geometries is limited by the requirements of a structured grid and a stable boundary treatment in the absence of artificial (numerical) dissipation. Cartesian embedded boundary (EB) approaches provide an efficient structured-grid framework to apply difference schemes over complex domains. However, they are often restricted to low orders of accuracy because of numerical instabilities at the embedded boundaries and the issues of small-cell problem that are difficult to address with high-order accuracy. The present work discusses a systematic approach to obtain high-order EB methods with non-dissipative centered schemes in the interior. This approach, based on satisfying the primary and secondary conservation conditions, is employed to derive EB schemes that are up to sixth-order accurate in the interior and fourth-order accurate globally for hyperbolic, parabolic as well as incompletely parabolic problems. The proposed finite-difference discretization is, by construction, dimensionally split and addresses the small-cell problem without any cell/geometry transformations, thus, highly simplifying implementation in a flow solver. Various linear and non-linear numerical tests are performed to evaluate the stability and the accuracy of the proposed EB schemes.

97 MATHEMATICS AND COMPUTING↗

The Gas-Jet Method of Deposition of Nanostructured Silver Films

The synthesis of thin silver films by the gas-jet deposition method is experimentally and theoretically studied. When the metal is deposited onto silicon substrates from a supersonic jet of silver vapor with a helium carrier gas, nanostructured films with a 3−30 nm size of nanostructures are obtained for a 1230−1380 K range of jet source temperatures. The data on Ag–He gas-jet dynamics when it is expanded into vacuum (velocity, temperature, concentration, flux of particles onto a substrate) depending on parameters at the source (vapor temperature, flow rate of a carrier gas) are obtained by the method of direct simulation Monte Carlo. The range of optimal helium flow rates, when the efficiency of a gas-jet source is maximal, is determined. It is established that the presence of a background gas in a deposition chamber at pressure higher than 1 Pa decreases the flow of particles onto a substrate, and a simple way of its evaluation is proposed. Conditions for formation of silver clusters in the jet are determined by using the simulation. It is shown that for experimental deposition regimes there are no clusters in the jet, and the observed silver nanostructures are formed on the substrate surface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Experimental Evaluation of a Cooled Radial-inflow Turbine

Two 14.4 inch tip diameter rotors were installed and tested in the Small Engines Component Turbine Facility (SECTF) at NASA Lewis Research Center. The rotors, a solid and a cooled version of a radial-inflow turbine, were tested with a 15 vane stat or over a set of rotational speeds ranging from 80 to 120 percent design speed (17,500 to 21,500 rpm). The total-to-total stage pressure ratios ranged from 2.5 to 5.5. The data obtained at the equivalent conditions using the solid version of the rotor are presented with the cooled rotor data. A Reynolds number of 381,000 was maintained for both rotors, whose stages had a design mass flow of 4.0 Ibm/sec, a design work level of 59.61 Btu/lbm, and a design efficiency of 87 percent. The results include mass flow data, turbine torque, turbine exit flow angles, stage efficiency, and rotor inlet and exit surveys.

Tirres, Lizet↗

Experimental evaluation of a cooled radial-inflow turbine

Two 14.4 inch tip diameter rotors were installed and tested in the Small Engines Component Turbine Facility (SECTF) at NASA Lewis Research Center. The rotors, a solid and a cooled version of a radial-inflow turbine, were tested with a 15 vane stat or over a set of rotational speeds ranging from 80 to 120 percent design speed (17,500 to 21,500 rpm). The total-to-total stage pressure ratios ranged from 2.5 to 5.5. The data obtained at the equivalent conditions using the solid version of the rotor are presented with the cooled rotor data. A Reynolds number of 381,000 was maintained for both rotors, whose stages had a design mass flow of 4.0 lbm/sec, a design work level of 59.61 Btu/lbm, and a design efficiency of 87 percent. The results include mass flow data, turbine torque, turbine exit flow angles, stage efficiency, and rotor inlet and exit surveys.

Tirres, Lizet↗

Model's sparse representation based on reduced mixed GMsFE basis methods

In this paper, we propose a model's sparse representation based on reduced mixed generalized multiscale finite element (GMsFE) basis methods for elliptic PDEs with random inputs. A typical application for the elliptic PDEs is the flow in heterogeneous random porous media. Mixed generalized multiscale finite element method (GMsFEM) is one of the accurate and efficient approaches to solve the flow problem in a coarse grid and obtain the velocity with local mass conservation. When the inputs of the PDEs are parameterized by the random variables, the GMsFE basis functions usually depend on the random parameters. This leads to a large number degree of freedoms for the mixed GMsFEM and substantially impacts on the computation efficiency. In order to overcome the difficulty, we develop reduced mixed GMsFE basis methods such that the multiscale basis functions are independent of the random parameters and span a low-dimensional space. To this end, a greedy algorithm is used to find a set of optimal samples from a training set scattered in the parameter space. Reduced mixed GMsFE basis functions are constructed based on the optimal samples using two optimal sampling strategies: basis-oriented cross-validation and proper orthogonal decomposition. Although the dimension of the space spanned by the reduced mixed GMsFE basis functions is much smaller than the dimension of the original full order model, the online computation still depends on the number of coarse degree of freedoms. To significantly improve the online computation, we integrate the reduced mixed GMsFE basis methods with sparse tensor approximation and obtain a sparse representation for the model's outputs. The sparse representation is very efficient for evaluating the model's outputs for many instances of parameters. To illustrate the efficacy of the proposed methods, we present a few numerical examples for elliptic PDEs with multiscale and random inputs. In particular, a two-phase flow model in random porous media is simulated by the proposed sparse representation method.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Using the boundary-layer equations in three-dimensional viscous flow simulation

A simple and computationally efficient algorithm for solving the unsteady three dimensional boundary layer equations in a time accurate or relaxation mode is presented. The algorithm is used to compute the separated flow over a 6:1 ellipsoid at angle of attack and the transonic flow over a finite wing with shock induced separation. These results are compared to available experimental data. A method of using the boundary layer algorithm to accelerate a Navier-Stokes computation is also presented. Example computations indicate that a boundary layer algorithm can be used to improve both the accuracy and efficiency of a Navier-Stokes algorithm.

Vandalsem, William R.↗

Transonic interactions of unsteady vortical flows

Unsteady interactions of strong concentrated vortices, distributed gusts, and sharp-edged gusts with stationary airfoils were analyzed in two-dimensional transonic flow. A simple and efficient method for introducing such vortical disturbances was implemented in numerical codes that range from inviscid transonic small disturbance to thin-layer Navier Stokes. The numerical results demonstrate the large distortions in the overall flow field and in the surface air loads that are produced by various vortical interactions. The results of the different codes are in excellent qualitative agreement, but, as might expected, the transonic small-disturbance calculations are deficient in the important region near the leading edge.

Mccroskey, W. J.↗

Efficiency of Mixed-Element USM3D for Benchmark Three-Dimensional Flows

The unstructured, mixed-element, cell-centered, finite-volume flow solver USM3D is enhanced with new capabilities such as line generation for general unstructured grids and optimization of the iterative solver. The efficiency of the new developments is assessed in a massively parallel environment. The assessments are conducted using a baseline method and the recent hierarchical adaptive nonlinear iteration method framework. Three benchmark turbulent flows, namely, a subsonic separated flow around a three-dimensional hemisphere cylinder configuration, a transonic flow around the ONERA M6 wing, and a supersonic flow through a square duct are considered.

Mohagna J Pandya↗

Numerical analysis of air dehumidification through electrospray-enhanced vortical flow cyclone separator

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air significantly below its dew point temperature. Here, this study numerically investigates air dehumidification achieved by electrostatic and dielectrophoresis forces in a converging duct and centrifugal principles in cyclone separators. An electrospray was employed to energize water droplets, which then captured water vapor via dielectrophoresis. A novelty of the present study is the inclusion of a cyclone separator positioned downstream of the electrospray. This combination increased the dehumidification efficiency and controlled the flow of the condensate. By integrating electrospray technology and applying an electric field, this study examines the impact of particle separation efficiency, pressure drops, and cyclone performance on air dehumidification. The control parameters for air dehumidification were investigated. Three cyclones were modelled for airflow rates of 5 cubic feet per minute [cfm] (0.0024 m 3 /s), 38 cfm (0.0179 m 3 /s), and 200 cfm (0.094 m 3 /s). The results indicated air dehumidification was up to 5.7 % under environmental conditions, similar to those used to validate the CFD model. The degree of air dehumidification was primarily influenced by the electric charge acquired by the water droplets, their flight trajectory, and the vorticity intensity within the cyclone. Air dehumidification could increase by up to 13 % by increasing the number of droplets injected into the air stream, the flight time, and the electrical charge. The breakdown electric field strength threshold near the electrospray was a limiting factor for further enhancing dehumidification performance. This study examines the optimization of an electro-assisted dehumidification system that includes cyclone-based droplet separation through numerical analysis. The results provide insights into the design of energy-efficient air treatment technologies.

42 ENGINEERING↗

Overall and blade element performance of a 1.20 pressure ratio fan stage with rotor blades reset -7 deg

A 51-cm-diam model of a fan stage for short haul aircraft was tested in a single stage compressor research facility. The rotor blades were set 7 deg toward the axial direction (opened) from the design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed and a weight flow of 30.9 kg/sec, the stage pressure ratio and efficiency were 1.205 and 0.85, respectively. The design speed rotor peak efficiency of 0.90 occurred at a flow rate of 32.5 kg/sec.

Lewis, G. W., Jr.↗